Difference between revisions of "ACPI"

From coreboot
Jump to: navigation, search
(Potential Issues)
(Further Resources)
Line 285: Line 285:
 
* [http://en.opensuse.org/S2ram Suspend to RAM utility]
 
* [http://en.opensuse.org/S2ram Suspend to RAM utility]
 
* [http://download.microsoft.com/download/5/b/9/5b97017b-e28a-4bae-ba48-174cf47d23cd/CPA002_WH06.ppt Windows Vista ACPI information, incl. advice on common problems in ACPI implementations]
 
* [http://download.microsoft.com/download/5/b/9/5b97017b-e28a-4bae-ba48-174cf47d23cd/CPA002_WH06.ppt Windows Vista ACPI information, incl. advice on common problems in ACPI implementations]
 +
* [http://smackerelofopinion.blogspot.com/2010/03/debugging-acpi-using-acpiexec.html Debugging ACPI using acpiexec]

Revision as of 20:17, 13 May 2010

This page contains some (developer) documentation about how ACPI can be used in coreboot.

ACPI setup HOWTO

Please have a look at the files in src/mainboard/asus/a8v-e_se. Please also check out http://acpi.info, which contains the ACPI specification.

Set up hardware

Set the PMIO base address to some known address, and set up the desired ACPI IRQ (usually IRQ9; sometimes it is called the SCI interrupt).

Fixed ACPI Description Table (FADT)

You may skip this section if your SB has it already. Just call it from your MB ACPI setup code (check M2V-MX SE for details).

Now you will need to create an ACPI table which describes the I/O port location for kernel ACPI implementation. This is the FACP table. You will need to create the fadt.c file and fill in the I/O port values plus IRQ:

fadt->sci_int = 9;
fadt->pm1a_evt_blk = VT8237R_ACPI_IO_BASE;
fadt->pm1b_evt_blk = 0x0;
fadt->pm1a_cnt_blk = VT8237R_ACPI_IO_BASE + 0x4;
fadt->pm1b_cnt_blk = 0x0;
fadt->pm2_cnt_blk = 0x0;
fadt->pm_tmr_blk = VT8237R_ACPI_IO_BASE + 0x8;
fadt->gpe0_blk = VT8237R_ACPI_IO_BASE + 0x20;
fadt->gpe1_blk = 0x0;

In this example the ACPI IRQ is 9, and the PM1A event block starts at VT8237R_ACPI_IO_BASE. You may obtain some values from cat /proc/ioport if running with the proprietary BIOS. Not all blocks are necessary—usually only PM1A PMTMR and GPE0 are used. Please note that this table has the I/O port information stored twice using different formats. Please consult the ACPI specification for details. Most settings in fadt.c can use their default values.

Differentiated System Description Table (DSDT)

The DSDT table contains a bytecode that is executed by a driver in the kernel. This table stores also ACPI routing information in _PRT methods. You may add those _PRT methods later.

Generic part of DSDT

A very generic DSDT table would look similar to the ASUS A8V-E/ASUS M2V-MX SE src/mainboard/asus/a8v-e_se/dsdt.asl file.

        Scope (\_PR)
        {
                Processor (\_PR.CPU0, 0x00, 0x000000, 0x00) {}
                Processor (\_PR.CPU1, 0x01, 0x000000, 0x00) {}
        }

This is here for compatibility. More interesting is:

        /* For now only define 2 power states:
         *  - S0 which is fully on
         *  - S5 which is soft off
         * any others would involve declaring the wake up methods
         */
        Name (\_S0, Package () {0x00, 0x00, 0x00, 0x00 })
        Name (\_S5, Package () {0x02, 0x02, 0x00, 0x00 })

This defines the SLP_TYP fields in PM1A register. In my case I need to store 010 to perform soft-off, and 000 to wake up. Modify it to fit your chipset needs.

Interrupt routing in DSDT

The _PRT methods define the routing, similar to PIR and MP Table.

     Package (0x04) { 0x000BFFFF, 0x00, 0x00, 0x10 }, //slot 0xB
     Package (0x04) { 0x000BFFFF, 0x01, 0x00, 0x11 },
     Package (0x04) { 0x000BFFFF, 0x02, 0x00, 0x12 },
     Package (0x04) { 0x000BFFFF, 0x03, 0x00, 0x13 },

This defines the slot 0xB (all functions FFFF) routing as follows:

INTA -> IRQ16
INTB -> IRQ17
INTC -> IRQ18
INTD -> IRQ19

Note: you cannot indicate the special functions like:

Package (0x04) { 0x000F0001, 0x00, 0x00, 0x14 }, // 0xf Native IDE IRQ 20

It means 0:0f.1 INTA is routed to IRQ20. Linux likes it. Windows does not (code 12). The ACPI standard requires that function is always 0xffff.

Please note that the 0x10, 0x11 are called GSI (global system interrupt). All your interrupts routed through first APIC will start with 0x00, second APIC will perhaps start at IRQ24 etc. This example has no support for legacy PIC routing. For PIC routing you would need to alter the rest of the fields in the _PRT package and also crete PIRQA-PIRQD special devices.

The described above uses static IRQ assignments. Some chipsets like MPC55/CK804 have a configuration register which indicates what APIC pins are routed to what interrupt. Those typically use dynamic IRQ routing which provides a _CRS and _SRS methods to set such registers. For now, those registers are filled in MP-Table setup of each MCP55/CK804 board. All you need is to have static wiring like the MP-Table has.

The rest of the file contains just some legacy devices to make certain OS installers happy. Don't forget to install the iasl compiler and also adjust the coreboot buildsystem to build the binary DSDT for you.

CPU Power Management

The CPU power management is hardware specific. It is described in APCI specs and also in AMD BIOS and Kernel Developer guide. The rest of this section describes the AMD specific part. AMD needs ACPI objects which describe the similar info as the legacy PowerNow table. Check the BKDG for details.

The content of the tables must be generated at runtime, which is a bit of a problem, because the AML code must be generated or DSDT patched. There is an acpigen infrastructure to generate the AML code.

The actual content for family 0fh revF and later P-States can be generated by complex algorithm implemented in amd_model_fxx_generate_powernow(). This function should be called in acpi_fill_ssdt_generator() callback. Up to revE, all P state info must be hardcoded in tables (not supported).

C States

C states are processor power states. C1 is mandantory and reached on IA32 compatible processors using the HLT instruction, C2 and C3 are optional and must be configured.

C states can be configured in ACPI using two methods:

  1. by defining the P_BLK base address in the Processor() Definition, and P_LVLx_LAT values in the FADT
  2. using the _CST object

P_BLK is easier to configure, if the hardware supports that method. ACPI defines that there must be two registers at P_BLK+4 and P_BLK+5 that initiate a transition to C2 or C3 when the register is read. After sleep, the read returns 0. P_LVLx_LAT define the worst case latency of the state transition.

_CST is necessary if you want to support more than 3 C states, or if the transition procedure doesn't follow the ACPI requirement.

PCI root bus _CRS method

Windows needs to know the actual decode ranges for PCI root bus (and any other). Windows needs to know platform independent way, how is I/O routed on PCI0 bus (and other busses).

  • For K8 this means to read the I/O and MMIO routing registers (same as k8resdump provides) and use them to create ACPI objects. The actual PCI regs are read in acpi-k8 in modelf and stored as SSDT table. The k8-util.asl code will construct the resources from that SSDT table. One can use the k8-util.asl code which will construct the resource objects. Check the ASUS M2V-MX mainboard ACPI code.
  • For i945 the required registers are read in the ASL code in northbridge/intel/i945/acpi/i945_hostbridge.asl.

DSDT debugging

There are two ways. You can store values in "debug" object, which will print it in dmesg. Check http://www.linuxhq.com/kernel/v2.6/28-rc6/Documentation/acpi/debug.txt how to turn that on. In DSDT use store method to write to Debug object. You can write buffers, ints etc:

* Store ("The answer to the question of live universe and everything is:", Debug) 
* Store (42, Debug) 

Second method is userspace interpretation of DSDT table. This can be achieved with APCI CA Unix package. It is located in acpica-unix-20081204/tools/acpiexec. You can eval the objects and run the methods, like _CRS for example.

If you receive a BSOD with STOP code 0xa5, check this: http://support.microsoft.com/kb/314830.

Other tables

Rest of the ACPI tables is located at acpi_tables.c. I will describe briefly all methods:

acpi_fill_mcfg

If your platform supports MMCONFIG (memory mapped PCI configuration registers, aka extended PCIe configuration) just modify the function with correct base address.

acpi_fill_madt

A system with 8259s and APICs

This table describes the ACPI IRQ information, as well as IRQ override. For code example check the M2V-MX SE acpi_tables. You will need to create the sub-table for LAPIC (the APIC counterpart in CPU) and describe the APICs and also deal with so called IRQ overrides.

Let’s look at the figure below which explains how the interrupts are routed.

The interrupt sources are on the right side. The legacy IRQs and the PCI IRQs are connected to both APIC and 8259.

In the legacy case, the APIC is programmed in virtual wire mode. It will just interconnect pin0 of APIC with its output, bypassing APIC completely. OS uses 8259s, and ignores APICs at all.

The APIC should be in this mode in BIOS, to do that for your SB, check the setup_ioapic in vt8237r_lpc.c. Please note that there is some bit which also says if APIC is delivering through wires, or through FSB messages.

But back to the table. You need to provide some kind of description of the APICs. Each APIC is identified with its own ID and with the offset where its IRQ starts. It is called GSI base – Global System Interrupt base. This is just the value which is used in the _PRT entries as offset for IRQ nr. Typically the first SB APIC has offset 0, second APIC starts where the first has finished, so at IRQ 24 if the first has 24 interrupt sources.

Last thing in this table are IRQ overrides. Usually there are two IRQ overrides. IRQ0 override means that IRQ0 is not connected to pin 0 on APIC but to another, most likely pin 2. Check the figure above why. Second IRQ override is for ACPI IRQ. This overrides the 'level' of the interrupt to 'active low'. The rest of the table is filled with NMI entries for the processor.


write_acpi_tables

This is the main function which constructs the tables. Functions described above are callbacks from the "construct" functions called here. You may omit the HPET and MCFG tables.

FACS table

This table must be aligned to 64B boundary (Windows checks this).

Suspend to RAM

There are patches on the mailing list which add support for suspend to RAM in coreboot. The resume start of the computer does not differ until OS waking vector is executed instead of payload.

Checklist of things which needs to be setup correctly:

  • Supend clocks, SUSA/B/C plane pins
  • Often the Super I/O has some pin to toggle the power for RAM
  • SLP_TYPE with S3 definition to your DSDT
  • Support for exit-self-refresh in your RAM controller
  • An NVRAM which stores the memory configuration, which is known runtime (DQS)
  • Chipset tweaks for S3 (like various signal delays)
  • CPU tweaks (for AMD the PM1 and PM2 registers and SMAF codes)
  • _RAMBASE of coreboot setup to 31MB and set LB_MEM_TOPK to 32MB
  • Make sure new code does not corrupt any memory
  • Make sure that you reserve _RAMBASE - LB_MEM_TOPK
  • SMP might need some fixes

ACPI bytecode generator

Some ACPI stuff is generated runtime. To achieve this goal we have a AML code generator which generates binary ACPI bytecode. Such code then resides typically in SSDT table. There is a helper function which creates such a table - acpi_create_ssdt_generator(). The content of the table is created through the callback function acpi_fill_ssdt_generator(). So far we have two big users of the generator k8acpi_write_vars() and amd_model_fxx_generate_powernow(). The first function will generate some runtime configuration of HT bus and PCI decode ranges. Second function generates the P-States.

The available functions are in acpigen.h. Mostly there are functions generating some primitive named data structures. However sometimes it's necessary to put more data to a package. ACPI AML code needs to know the block lengths. The len is unknown until we have filled the payload of such package. Therefore when we are done, we need to call function acpigen_patch_len(int len) which will patch last object (package) which need patching. It uses stack internally so more structures can be nested. Look to acpigen.c and learn what functions call acpigen_write_len_f() - those needs patching.

Debugging ACPI

When CONFIG_ACPI_DEBUG is compiled into the kernel, the ACPI debug level can be specified on the kernel command line:

acpi.debug_level=0x2003
(warn, error und tables debug enabled)

The values can be checked at runtime:

# cat /sys/module/acpi/parameters/debug_level
Description                     Hex        SET 
ACPI_LV_ERROR                   0x00000001 [*]
ACPI_LV_WARN                    0x00000002 [*]
ACPI_LV_INIT                    0x00000004 [*]
ACPI_LV_DEBUG_OBJECT            0x00000008 [ ]
ACPI_LV_INFO                    0x00000010 [ ]
ACPI_LV_INIT_NAMES              0x00000020 [ ]
ACPI_LV_PARSE                   0x00000040 [ ]
ACPI_LV_LOAD                    0x00000080 [ ]
ACPI_LV_DISPATCH                0x00000100 [ ]
ACPI_LV_EXEC                    0x00000200 [ ]
ACPI_LV_NAMES                   0x00000400 [ ]
ACPI_LV_OPREGION                0x00000800 [ ]
ACPI_LV_BFIELD                  0x00001000 [ ]
ACPI_LV_TABLES                  0x00002000 [ ]
ACPI_LV_VALUES                  0x00004000 [ ]
ACPI_LV_OBJECTS                 0x00008000 [ ]
ACPI_LV_RESOURCES               0x00010000 [ ]
ACPI_LV_USER_REQUESTS           0x00020000 [ ]
ACPI_LV_PACKAGE                 0x00040000 [ ]
ACPI_LV_ALLOCATIONS             0x00100000 [ ]
ACPI_LV_FUNCTIONS               0x00200000 [ ]
ACPI_LV_OPTIMIZATIONS           0x00400000 [ ]
ACPI_LV_MUTEX                   0x01000000 [ ]
ACPI_LV_THREADS                 0x02000000 [ ]
ACPI_LV_IO                      0x04000000 [ ]
ACPI_LV_INTERRUPTS              0x08000000 [ ]
ACPI_LV_AML_DISASSEMBLE         0x10000000 [ ]
ACPI_LV_VERBOSE_INFO            0x20000000 [ ]
ACPI_LV_FULL_TABLES             0x40000000 [ ]
ACPI_LV_EVENTS                  0x80000000 [ ]
--
debug_level = 0x00000007 (* = enabled)

Potential Issues

Windows Errors

STOP 0xa5

A Blue Screen Of Death with STOP code 0x000000A5 is ACPI related, and it seems that Microsoft is very strict when it comes to ACPI compliance. http://support.microsoft.com/kb/314830/en explains some of the error codes, but not all of them.

  • Parameter1 == 0x00001000 means that some memory resource is claimed by ACPI that, according to memory tables, belongs to the OS. Parameter3 is the start address, Parameter4 is the length of the range. They can probably be found somewhere in the ASL code.
  • Parameter1 == 0x0000000D means that some _ADR or _HID Symbol is missing in the dsdt.asl.
  • Parameter1 == 0x00000011 is "something in the ACPI init". This can be improper object names, like an object "\._PR_foo" inside the "\._PR" scope (it should be just "foo" instead, or the surrounding scope killed)

The documentation of windbg has more detailed information about STOP 0xa5 than the MSDN article.

Other errors

  • Quoting MSDN: A "Stop: 0x0000007E" error message or a "Stop: 0x0000008E" error message typically means that a kernel mode component, such as a driver, encountered an error that could not be handled by the built-in Windows error handler.

Linux Errors

ACPI 2.0/3.0 without XSDT

Linux 2.6.12.x requires an XSDT if the RSDP revision is larger than 0 as it's hardcoded to use that instead of the RSDT then. Fixed in later Linux versions.

PCI Hotplug _BBN fail

If you are seeing the following error you are on a (most likely old) system with PCI(e) hotplug. 

pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5

Add the following under PCI0 device to get rid of the error:

Name(_ADR, 0) 
Name(_BBN, 0)

Random Notes

Don't nest scopes improperly

Windows ACPI doesn't like

Scope(\foo) {
  Name(\foo.bar) { ... }
}

Either make that

Scope(\foo) {
  Name (bar) { .. }
}

or eliminate the scope:

Name(\foo.bar) { ... }

Shutdown sequences differ between systems

Success with shutting down a system from Windows doesn't mean that Linux properly shuts down the system (and this probably applies the other way around, too)

Further Resources