ASRock 939A785GMH-128M - Revision history

Ruik: /* Status */

2011-02-26T19:58:22Z

‎Status

2011-02-26T19:55:08Z

‎Status

2011-02-26T19:53:56Z

‎RAM

2011-02-26T19:52:44Z

‎Known Issues

2011-02-26T19:51:32Z

PCIe x16

2010-12-05T12:58:30Z

DualChannel worked after all

2010-12-05T12:32:16Z

Markup

2010-12-05T12:30:24Z

New RAM testings

2010-11-30T20:31:39Z

‎RAM

2010-11-30T20:27:23Z

add led note

@@ Line 47: / Line 47: @@
 |RAM_DDR3_status = N/A
 |RAM_ecc_status = N/A
 |IDE_status = OK
@@ Line 75: / Line 76: @@
 |PCIE_x4_status = N/A
 |PCIE_x8_status = N/A
 |PCIE_x32_status = N/A
 |HTX_status = N/A

@@ Line 51: / Line 51: @@
 |IDE_comments = checked with a CD-ROM drive
 |IDE_25_status = N/A
-|SATA_status = WIP
+|SATA_status = OK (check note)
 |Onboard_SCSI_status = N/A
 |USB_status = OK

← Older revision		Revision as of 19:53, 26 February 2011
Line 91:		Line 91:

	== Known Issues ==		== Known Issues ==
		+
		+	=== SATA ===
		+
		+	External and SATA port 4 is not detected. This is due to bug in Coreboot code with regards of Combined mode handling.

	=== RAM ===		=== RAM ===

@@ Line 116: / Line 116: @@
 === PCI-E graphics adapter ===
-* Wouldn't work. With both plugged in and CONFIG_CONSOLE_VGA_ONBOARD_AT_FIRST not set there was no video output. I had the vgabios for the onboard adapter still inside the coreboot.rom however.
+* Should be now fixed - r6384
 === Keyboard in Grub ===

← Older revision		Revision as of 19:51, 26 February 2011
Line 24:		Line 24:

	Suspend LED is the power LED - register 0f3 in SIO. Low = on		Suspend LED is the power LED - register 0f3 in SIO. Low = on
		+
		+	=== PCIe x16 ===
		+
		+	Reset signal is through GPIO - GPM8,GPM9, 0 asserts reset, 1 de-asserts reset.

	== Status ==		== Status ==

@@ Line 100: / Line 100: @@
 ==== Lennart tests ====
-* blue slots populated - works, but dualchannel doesn't (setpci -s 18.2 90.l outputs a c as third from right byte)
+* blue slots populated - works
 * all slots populated -- doesn't boot
 ** hangs on "Clearing initial memory region:"

@@ Line 100: / Line 100: @@
 ==== Lennart tests ====
+* blue slots populated - works, but dualchannel doesn't (setpci -s 18.2 90.l outputs a c as third from right byte)
-* Using 2 512 MB DIMMs I got 756 MB of usable RAM (as opposed to 881 with the vendor BIOS - most likely UMA settings).
+* all slots populated -- doesn't boot
-* With only 1 512 MB DIMM the system wouldn't boot.
+ * hangs on "Clearing initial memory region:"
-* With my 4 DIMMS from 3 vendors (2x A, 1x B, 1x C) I get the following boot chances. These might be related to another issue and not to the port of this board.
+* only channel0 populated - doesn't boot
-{| border="1"
+ * hangs on "Clearing initial memory region:"
-|+ RAM and booting
+* single DIMM in DDR1 - works.
-! DIMM configuration !! Boots?
-|-
-|A/A || style="background:green;" | Yes
-|-
-|A || style="background:red;" | No
-|-
-|A/A/B/C || style="background:red;" | No
-|-
-|B/C/A/A || style="background:green;" | Yes
-|}
 === Onboard VGA ===

@@ Line 89: / Line 89: @@
 === RAM ===
 * Using 2 512 MB DIMMs I got 756 MB of usable RAM (as opposed to 881 with the vendor BIOS).
 * With only 1 512 MB DIMM the system wouldn't boot.
 * With my 4 DIMMS from 3 vendors (2x A, 1x B, 1x C) I get the following boot chances. These might be related to another issue and not to the port of this board.

@@ Line 21: / Line 21: @@
 GPO35 - loadline control (0 enabled)
 GPO44 | GPO45  | GPO46 - DDR memory voltage
 == Status ==