Difference between revisions of "ASUS M2A-VM"

From coreboot
Jump to: navigation, search
m (Status: No PCI-X)
m (Status: more flashrom updates)
 
(2 intermediate revisions by one user not shown)
Line 85: Line 85:
 
|WakeOnKeyboard_status = Untested
 
|WakeOnKeyboard_status = Untested
 
|WakeOnMouse_status = Untested
 
|WakeOnMouse_status = Untested
|Flashrom_status = WIP
+
|Flashrom_status = OK
|Flashrom_comments = [http://www.coreboot.org/pipermail/coreboot/2007-September/025281.html Reported as working with the proprietary BIOS.]
+
  
 
}}
 
}}
 
== Flashrom ==
 
 
You need [http://www.coreboot.org/pipermail/coreboot/2009-February/044573.html this patch] for flashrom as of 2009/02.
 
  
 
== Bootlog ==
 
== Bootlog ==

Latest revision as of 23:06, 21 June 2009

This page describes how to use coreboot on the ASUS M2A-VM mainboard.

Status

Device/functionality Status Comments
CPU
CPU works OK
L1 cache enabled OK
L2 cache enabled OK
L3 cache enabled N/A
Multiple CPU support N/A
Multi-core support Untested
Hardware virtualization Untested
RAM
EDO N/A
SDRAM N/A
SO-DIMM N/A
DDR N/A
DDR2 WIP Works with 2 GB. Broken with 4 GB.
DDR3 N/A
Dual channel support WIP Does not work with 2x2 GB unmatched DIMMS in a dualchannel setup (expected). Patches have been sent to the list to partially fix this.
ECC support Untested
On-board Hardware
On-board IDE 3.5" OK
On-board IDE 2.5" N/A
On-board SATA OK Not working: SATA multicount transfers (detected as unsupported by Linux)
On-board SCSI N/A
On-board USB OK
On-board VGA OK VESA framebuffer console does not work if you select x86emu because the VESA call interface is not available. A normal X server works fine even with 3D (radeonhd driver).
On-board ethernet OK
On-board audio WIP Stereo output (onboard jack) in HD Audio mode works. Onboard jack for microphone input seems not to work due to an unknown reason. Coreboot says "No verb!". Linux kernel complains "hda_codec: Unknown model for ALC883, trying auto-probe from BIOS..."
On-board modem N/A
On-board FireWire N/A
On-board smartcard reader N/A
On-board CompactFlash N/A
On-board PCMCIA N/A
Add-on slots/cards
ISA add-on cards N/A
Audio/Modem-Riser (AMR/CNR) cards N/A
PCI add-on cards OK Only one slot was tested.
Mini-PCI add-on cards N/A
PCI-X add-on cards N/A
AGP graphics cards N/A
PCI Express x1 add-on cards Untested
PCI Express x2 add-on cards N/A
PCI Express x4 add-on cards N/A
PCI Express x8 add-on cards N/A
PCI Express x16 add-on cards Untested
PCI Express x32 add-on cards N/A
HTX add-on cards N/A
Legacy / Super I/O
Floppy Untested
Serial port 1 (COM1) OK
Serial port 2 (COM2) N/A
Parallel port Untested
PS/2 keyboard OK
PS/2 mouse Untested
Game port Untested
Infrared N/A
PC speaker Untested
DiskOnChip N/A
Miscellaneous
Sensors / fan control WIP
Hardware watchdog Untested
SMBus Unknown
CAN bus N/A
CPU frequency scaling OK
Other powersaving features N/A
ACPI WIP power button works, software poweroff works, suspend is untested
Reboot OK
Poweroff OK
Suspend Unknown
Nonstandard LEDs N/A
High precision event timers (HPET) Untested
Random number generator (RNG) N/A
Wake on modem ring Untested
Wake on LAN Untested
Wake on keyboard Untested
Wake on mouse Untested
Flashrom OK

Bootlog

The bootlog is available.


Lspci

Proprietary bios

00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx)
00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3)
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA
00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0)
00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1)
00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2)
00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3)
00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4)
00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI)
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 13)
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc RS690 [Radeon X1200 Series]
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
# lspci -vvvvvvvnx
00:00.0 0600: 1002:7910
	Subsystem: 1043:826d
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 64
00: 02 10 10 79 06 00 20 22 00 00 00 06 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 6d 82
30: 00 00 00 00 c4 00 00 00 00 00 00 00 00 00 00 00

00:01.0 0604: 1002:7912 (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 99
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: fdc00000-fddfffff
	Prefetchable memory behind bridge: 00000000fa000000-00000000fbffffff
	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [b0] Subsystem: 1002:7912
	Kernel modules: shpchp
00: 02 10 12 79 07 00 30 02 00 00 04 06 00 63 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 44 d1 d1 20 02
20: c0 fd d0 fd 01 fa f1 fb 00 00 00 00 00 00 00 00
30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 08 00

00:07.0 0604: 1002:7917 (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: fdb00000-fdbfffff
	Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag+ RBE+ FLReset-
		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
			ClockPM- Suprise- LLActRep+ BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
		Address: fee0300c  Data: 4149
	Capabilities: [b0] Subsystem: 1043:826d
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Virtual Channel <?>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp
00: 02 10 17 79 07 04 10 00 00 00 04 06 08 00 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 e1 e1 00 00
20: b0 fd b0 fd f1 fd f1 fd 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00

00:12.0 0106: 1002:4380 (prog-if 01 [AHCI 1.0])
	Subsystem: 1043:8231
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin A routed to IRQ 22
	Region 0: I/O ports at ff00 [size=8]
	Region 1: I/O ports at fe00 [size=4]
	Region 2: I/O ports at fd00 [size=8]
	Region 3: I/O ports at fc00 [size=4]
	Region 4: I/O ports at fb00 [size=16]
	Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [70] SATA HBA <?>
	Kernel driver in use: ahci
	Kernel modules: ahci
00: 02 10 80 43 07 00 30 02 00 01 06 01 00 40 00 00
10: 01 ff 00 00 01 fe 00 00 01 fd 00 00 01 fc 00 00
20: 01 fb 00 00 00 f0 02 fe 00 00 00 00 43 10 31 82
30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 00 00

00:13.0 0c03: 1002:4387 (prog-if 10 [OHCI])
	Subsystem: 1043:81ef
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd
	Kernel modules: ohci-hcd
00: 02 10 87 43 07 00 a0 02 00 10 03 0c 08 40 80 00
10: 00 e0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ef 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00

00:13.1 0c03: 1002:4388 (prog-if 10 [OHCI])
	Subsystem: 1043:81ef
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd
	Kernel modules: ohci-hcd
00: 02 10 88 43 07 00 a0 02 00 10 03 0c 08 40 00 00
10: 00 d0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ef 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 02 00 00

00:13.2 0c03: 1002:4389 (prog-if 10 [OHCI])
	Subsystem: 1043:81ef
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd
	Kernel modules: ohci-hcd
00: 02 10 89 43 07 00 a0 02 00 10 03 0c 08 40 00 00
10: 00 c0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ef 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 03 00 00

00:13.3 0c03: 1002:438a (prog-if 10 [OHCI])
	Subsystem: 1043:81ef
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd
	Kernel modules: ohci-hcd
00: 02 10 8a 43 07 00 a0 02 00 10 03 0c 08 40 00 00
10: 00 b0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ef 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 02 00 00

00:13.4 0c03: 1002:438b (prog-if 10 [OHCI])
	Subsystem: 1043:81ef
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd
	Kernel modules: ohci-hcd
00: 02 10 8b 43 07 00 a0 02 00 10 03 0c 08 40 00 00
10: 00 a0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ef 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 03 00 00

00:13.5 0c03: 1002:4386 (prog-if 20 [EHCI])
	Subsystem: 1043:81ef
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 64 bytes
	Interrupt: pin D routed to IRQ 19
	Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+
	Capabilities: [e4] Debug port: BAR=1 offset=00e0
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd
00: 02 10 86 43 17 00 b0 02 00 20 03 0c 10 40 00 00
10: 00 90 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ef 81
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 04 00 00

00:14.0 0c05: 1002:4385 (rev 13)
	Subsystem: 1043:81ef
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop+ ParErr+ Stepping+ SERR+ FastB2B+ DisINTx+
	Status: Cap+ 66MHz+ UDF+ FastB2B+ ParErr+ DEVSEL=?? >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx+
	Latency: 0
	Region 0: I/O ports at 0b00 [size=16]
	Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
	Kernel driver in use: piix4_smbus
	Kernel modules: i2c-piix4
00: 02 10 85 43 ff ff ff ff 13 00 05 0c 00 00 80 00
10: 01 0b 00 00 ff ff ff ff 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ef 81
30: 00 00 00 00 b0 00 00 00 00 00 00 00 00 00 00 00

00:14.1 0101: 1002:438c (prog-if 8a [Master SecP PriP])
	Subsystem: 1043:81ef
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin A routed to IRQ 16
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at f900 [size=16]
	Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
		Address: 00000000  Data: 0000
	Kernel driver in use: ATIIXP_IDE
	Kernel modules: ata_generic, ide-pci-generic, atiixp
00: 02 10 8c 43 05 00 30 02 00 8a 01 01 00 40 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: 01 f9 00 00 00 00 00 00 00 00 00 00 43 10 ef 81
30: 00 00 00 00 70 00 00 00 00 00 00 00 ff 01 00 00

00:14.2 0403: 1002:4383
	Subsystem: 1043:8249
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin ? routed to IRQ 16
	Region 0: Memory at fe020000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000
	Kernel driver in use: HDA Intel
	Kernel modules: snd-hda-intel
00: 02 10 83 43 06 00 10 04 00 00 03 04 08 40 00 00
10: 04 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 49 82
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 00 00 00

00:14.3 0601: 1002:438d
	Subsystem: 1043:81ef
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
00: 02 10 8d 43 0f 00 20 02 00 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ef 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:14.4 0604: 1002:4384 (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
	I/O behind bridge: 0000c000-0000cfff
	Memory behind bridge: fcc00000-fd7fffff
	Prefetchable memory behind bridge: fde00000-fdefffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00: 02 10 84 43 27 00 a0 02 00 01 04 06 00 40 81 00
10: 00 00 00 00 00 00 00 00 00 03 03 40 c0 c0 80 22
20: c0 fc 70 fd e0 fd e0 fd 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.0 0600: 1022:1100
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: [80] HyperTransport: Host or Secondary Interface
		!!! Possibly incomplete decoding
		Command: WarmRst+ DblEnd-
		Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
		Revision ID: 1.02
00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00

00:18.1 0600: 1022:1101
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.2 0600: 1022:1102
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.3 0600: 1022:1103
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: [f0] Secure device <?>
	Kernel driver in use: k8temp
	Kernel modules: k8temp
00: 22 10 03 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00

01:05.0 0300: 1002:791e (prog-if 00 [VGA controller])
	Subsystem: 1043:826d
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 7
	Region 0: Memory at fa000000 (64-bit, prefetchable) [size=32M]
	Region 2: Memory at fddf0000 (64-bit, non-prefetchable) [size=64K]
	Region 4: I/O ports at de00 [size=256]
	Region 5: Memory at fdc00000 (32-bit, non-prefetchable) [size=1M]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000
00: 02 10 1e 79 07 00 10 00 00 00 00 03 08 40 00 00
10: 0c 00 00 fa 00 00 00 00 04 00 df fd 00 00 00 00
20: 01 de 00 00 00 00 c0 fd 00 00 00 00 43 10 6d 82
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00

02:00.0 0200: 10ec:8168 (rev 01)
	Subsystem: 1043:81aa
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 1278
	Region 0: I/O ports at ee00 [size=256]
	Region 2: Memory at fdbff000 (64-bit, non-prefetchable) [size=4K]
	Expansion ROM at fdbc0000 [disabled] [size=128K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [48] Vital Product Data <?>
	Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
		Address: 00000000fee0300c  Data: 4159
	Capabilities: [60] Express (v1) Endpoint, MSI 00
		DevCap:	MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited
			ExtTag+ AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 4096 bytes
		DevSta:	CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
			ClockPM- Suprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [84] Vendor Specific Information <?>
	Capabilities: [100] Advanced Error Reporting <?>
	Capabilities: [12c] Virtual Channel <?>
	Capabilities: [148] Device Serial Number 68-81-ec-10-00-00-00-1a
	Capabilities: [154] Power Budgeting <?>
	Kernel driver in use: r8169
	Kernel modules: r8169
00: ec 10 68 81 07 04 10 00 01 00 00 02 10 00 00 00
10: 01 ee 00 00 00 00 00 00 04 f0 bf fd 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 aa 81
30: 00 00 bc fd 40 00 00 00 00 00 00 00 05 01 00 00

Other issues

MMCONFIG is not enabled. The patch to enable it causes ethernet to fail, but the reason is still unclear. Maybe that bug will be fixed by supplying a MCFG ACPI table. MMCONFIG is disabled in coreboot for too long. This could cause other issues. The current in-tree code has broken SATA handling in ACPI. The MMCONFIG enable patch fixes SATA ACPI. MMCONFIG is enabled twice(!) in coreboot before being disabled. The MMCONFIG handling is in the RS690 code (if you want to dive in and fix this).

Need to investigate why 4 GB RAM disturb USB and SATA to the point that Linux won't boot. Maybe some BAR collides with RAM.

The ACPI code is not fully 64bit safe.

Thermal code is for the DBM690T. Needs to be stripped out and replaced.

SuperI/O and thermal handling need to be factored out from main ACPI dsdt.asl.

SB600 SMBus (00:14.0) resource allocation has problems:

ERROR: PCI: 00:14.0 74 mem size: 0x0000001000 not assigned
ERROR: PCI: 00:14.0 14 mem size: 0x0000000400 not assigned
ERROR: PCI: 00:14.0 10 io size: 0x0000000010 not assigned


Public domain I, the copyright holder of this work, hereby release it into the public domain. This applies worldwide.

In case this is not legally possible:
I grant anyone the right to use this work for any purpose, without any conditions, unless such conditions are required by law.