Board:lenovo/x201: Difference between revisions

From coreboot
Jump to navigation Jump to search
No edit summary
m (sort the flash layout by location)
(48 intermediate revisions by 4 users not shown)
Line 1: Line 1:
== Status ==
== Status ==
* suspend to RAM (S3) currently fails.
Thanks for your interest in Lenovo X201 port.
Issues:
* Sometimes Gnome starts to think that battery is 10 time larger than real. Information from sysfs remains correct. Doesn't appear in newer gnome
* Yellow USB port is not powered when computer is shut down or in S3.
* Most times after suspend an EC IRQ hangs in the queue and all functions keys stopped working until cold boot.
 
Tested:
* RAM module combinations of 4G+4G, 4G, 2G+2G,4G+2G, 2G
* suspend to RAM (S3)
* USB
* Video (both internal and VGA)
* Expresscard slot (including hotplug)
* Sound
* LAN
* mini-PCIe slots (both wlan and wwan)
* Linux (through GRUB-as-payload & SeaBIOS-as-payload)
* Windows (through GRUB-as-payload loading SeaBIOS image from disk; you have to use extracted VGA blob, dumped from memory isn't good enough)
* SD card slot
* Thermal management
* Fingerprint reeader.
* Webcam
* Bluetooth
* Digitizer on X201t variant.
Not tested:
* Modem


== proprietary components status ==
== proprietary components status ==
* CPU Microcode (optional)
* CPU Microcode
* VGA option rom (optional)
* VGA option rom (optional): you need it if you wantgraphics in SeaBIOS but most payloads should work without it (text mode or corebootfb mode)
* ME(Management Engine) => you do not have to touch it(just leave it where it is)
* [[Intel_Management_Engine|ME(Management Engine)] => you do not have to touch it(just leave it where it is)
* EC(Embedded Controller) =>  you do not have to touch it(just leave it where it is)
* EC(Embedded Controller) =>  you do not have to touch it(just leave it where it is)
== Code ==
== Code ==
* [http://review.coreboot.org/#/c/2663/ The code is here]
{{MergedIntoMaster|review_url=http://review.coreboot.org/#/c/4514/}}
 
== Flashing ==
== Flashing ==
* you need an external programmer to flash it.
Flash in X201 is divided roughly in 4 parts:
* The flash chip is divided between the ME and the BIOS:
 
  <phcoder> First 5M is ME firmware, last 3M is BIOS/coreboot
* Descriptor (12K)
* To find exactly where it's divided run that command(the example below is on another laptop):
* ME firmware (5M-12K)
  [root@N71Jq ~]# flashrom -r bios.bin -pinternal:laptop=force_I_want_a_brick
* Rewriteable flash (3M-96K)
  flashrom v0.9.6.1-r1564 on Linux 3.8.2-1-LIBRE (x86_64)
* Locked bootblock (96K)
 
Descriptor and bootblock are read-only. ME firmware is not readable.
Rewriteable region can be rewritten easily with flashrom.
 
For coreboot we need to preserve descriptor and ME firmware while overwriting
rewriteable region and bootblock. To achieve this there are 2 ways:
 
* External flasher.
* Unlock bootblock
 
For the first one proceeds as follows:
* Turn off your laptop, remove battery and AC adapter.
* Remove the keyboard.
* Connect your external SPI flasher to the SPI chip which is under keyboard,
around the position of trackpoint under protective layer.
{|
|[[File:Lenovo-x201-bios-location-arrow.png |200px|thumb|center|found it!]]
|[[File:X201_flash_location.png |200px|thumb|center|under the keyboard]]
|}
[[File:Spi-soic8-25L6445E.png|200px|thumb|right|The flash chip]]
 
I recommend using SOIC-8 clip. Depending on the flasher you use, you may have to use separate
3.3V source. Make sure not to feed more than 3.3V ot the chip. I used
buspirate as flasher and 3.3V power lines from another computer.
The pinout is as follows, the colors are buspirate colors
  ===  front (display) ====
  3.3V (red)  N/C          violet (CLK)  MOSI (gray)
      |        |            |              |
  dot  |        |            |              |
  CS (white)  MISO (black) N/C          ground (brown)
  ===  back (touchpad) ===
 
* Read the flash. Twice. Compare the files to be sure. Save a copy of it on
external media.
flashrom -p <yourprogrammer> -r flash.bin
  flashrom -p <yourprogrammer> -r flash2.bin
diff flash.bin flash2.bin
 
If you have trouble reading the chip successfully,
the most common problems are
*insufficient power supply
*bad contacts
*too long wires
*bad pinout
The cable shipped with buspirate was too long, and needed to be trimmed.
 
See also [http://flashrom.org/ISP In-System Programming]
 
 
* Recover descriptor and me firmare:
  dd if=flash.bin of=coreboot/3rdparty/mainboard/lenovo/x201/descriptor.bin \
    count=12288 bs=1M iflag=count_bytes
  dd if=flash.bin of=coreboot/3rdparty/mainboard/lenovo/x201/me.bin \
    skip=12288 count=5230592 bs=1M iflag=count_bytes,skip_bytes
* Compile coreboot. Remember to enable HAVE_IFD and HAVE_ME_BIN
* Flash the resulting build/coreboot.rom
 
The other way has never been successfully used but it's known that the
locking mechanism is in bootblock itself and that original firmware has
a way to update it as follows:
* Flash an update of rewriteable region. On next boot bootblock parses the
image and sees that it contains a compressed copy of new bootblock. That
copy is uncompressed and flashed.
A way to unlock the bootblock would be to modify a firmware update to have a
copy of bootblock without protection. For this you need to compress the
modified block to fit into original space. The compression used is Lempel-Ziv-
Huffman variant. I've written a compressor for it but unfortunately it's not
performant enough.
 
 
===identify the regions===
  [root@x201 ~]# flashrom -r bios.bin -pinternal:laptop=force_I_want_a_brick
  flashrom v0.9.6.1-r1563 on Linux 3.10-1-grml-amd64 (x86_64)
  flashrom is free software, get the source code at http://www.flashrom.org
  flashrom is free software, get the source code at http://www.flashrom.org
   
   
  Calibrating delay loop... OK.
  Calibrating delay loop... OK.
========================================================================
  Found chipset "Intel QM57". Enabling flash write... WARNING: SPI Configuration Lockdown activated.
WARNING! You may be running flashrom on an unsupported laptop. We could
FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only.
not detect this for sure because your vendor has not setup the SMBIOS
  FREG2: WARNING: Management Engine region (0x00003000-0x004fffff) is locked.
tables correctly. You can enforce execution by adding
PR0: WARNING: 0x007d0000-0x01ffffff is read-only.
'-p internal:laptop=this_is_not_a_laptop' to the command line, but
please read the following warning if you are not sure.
Laptops, notebooks and netbooks are difficult to support and we
recommend to use the vendor flashing utility. The embedded controller
(EC) in these machines often interacts badly with flashing.
See http://www.flashrom.org/Laptops for details.
If flash is shared with the EC, erase is guaranteed to brick your laptop
and write may brick your laptop.
Read and probe may irritate your EC and cause fan failure, backlight
failure and sudden poweroff.
You have been warned.
========================================================================
Proceeding anyway because user forced us to.
  Found chipset "Intel HM55".  
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to flashrom@flashrom.org including a verbose (-V) log.
Thank you!
Enabling flash write... FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only.
  FREG2: WARNING: Management Engine region (0x00003000-0x001fffff) is locked.
  Please send a verbose log to flashrom@flashrom.org if this board is not listed on
  Please send a verbose log to flashrom@flashrom.org if this board is not listed on
  http://flashrom.org/Supported_hardware#Supported_mainboards yet.
  http://flashrom.org/Supported_hardware#Supported_mainboards yet.
Line 51: Line 128:
  If you force flashrom you will get no support if something breaks.
  If you force flashrom you will get no support if something breaks.
  OK.
  OK.
  Found SST flash chip "SST25VF032B" (4096 kB, SPI) at physical address 0xffc00000.
  Found Macronix flash chip "MX25L6405" (8192 kB, SPI) at physical address 0xff800000.
  Reading flash... Transaction error!
  Reading flash... FAILED.
Read operation failed!
 
FAILED.
it will print the ME regions:
it will print the ME regions:
  FREG2: WARNING: Management Engine region (0x00003000-0x001fffff) is locked.
  FREG2: WARNING: Management Engine region (0x00003000-0x004fffff) is locked.
it will also print the chip:
it will also print the chip:
  Found SST flash chip "SST25VF032B" (4096 kB, SPI) at physical address 0xffc00000.
  Found Macronix flash chip "MX25L6405" (8192 kB, SPI) at physical address 0xff800000.
=> verify if its voltage match with the programmer voltage...
'''But as in this case, flashrom might misidentify the chip''', this output is from [[Media:Spi-soic8-25L6445E.png|this MX25L6445E]]
* Then man flashrom says:
 
visually verify your chip's part number and find an [http://www.macronix.com/QuickPlace/hq/PageLibrary4825740B00298A3B.nsf/h_Index/3F21BAC2E121E17848257639003A3146/$File/MX25L6445E,%203V,%2064Mb,%20v1.8.pdf appropriate datasheet ]
 
=>verify that its voltage matches with the programmer voltage...
* Use flashrom layouts:
         -l, --layout <file>
         -l, --layout <file>
              Read ROM layout from <file>.
 
X201 Layout
000000000:00000fff fd
000001000:00002fff gbe
000003000:004fffff me
000500000:007fffff bios
   
   
              flashrom  supports  ROM  layouts. This allows you to flash certain parts of the flash chip only. A ROM layout file contains multiple lines with the following
 
              syntax:
To flash only the bios partition (coreboot) do:
  flashrom -l <layout> -i bios -w coreboot.rom
                startaddr:endaddr imagename
              startaddr and endaddr are hexadecimal addresses within the ROM file and do not refer to any physical address. Please note that using a 0x  prefix  for  those
              hexadecimal  numbers  is  not necessary, but you can't specify decimal/octal numbers.  imagename is an arbitrary name for the region/image from  startaddr to
              endaddr (both addresses included).
              Example:
   
                00000000:00008fff gfxrom
                00009000:0003ffff normal
                00040000:0007ffff fallback
              If you only want to update the image named normal in a ROM based on the layout above, run
                flashrom -p prog --layout rom.layout --image normal -w some.rom
              To update only the images named normal and fallback, run:
                flashrom -p prog -l rom.layout -i normal -i fallback -w some.rom
              Overlapping sections are not supported.

Revision as of 19:56, 31 May 2015

Status

Thanks for your interest in Lenovo X201 port. Issues:

  • Sometimes Gnome starts to think that battery is 10 time larger than real. Information from sysfs remains correct. Doesn't appear in newer gnome
  • Yellow USB port is not powered when computer is shut down or in S3.
  • Most times after suspend an EC IRQ hangs in the queue and all functions keys stopped working until cold boot.

Tested:

  • RAM module combinations of 4G+4G, 4G, 2G+2G,4G+2G, 2G
  • suspend to RAM (S3)
  • USB
  • Video (both internal and VGA)
  • Expresscard slot (including hotplug)
  • Sound
  • LAN
  • mini-PCIe slots (both wlan and wwan)
  • Linux (through GRUB-as-payload & SeaBIOS-as-payload)
  • Windows (through GRUB-as-payload loading SeaBIOS image from disk; you have to use extracted VGA blob, dumped from memory isn't good enough)
  • SD card slot
  • Thermal management
  • Fingerprint reeader.
  • Webcam
  • Bluetooth
  • Digitizer on X201t variant.

Not tested:

  • Modem

proprietary components status

  • CPU Microcode
  • VGA option rom (optional): you need it if you wantgraphics in SeaBIOS but most payloads should work without it (text mode or corebootfb mode)
  • [[Intel_Management_Engine|ME(Management Engine)] => you do not have to touch it(just leave it where it is)
  • EC(Embedded Controller) => you do not have to touch it(just leave it where it is)

Code

{{ #if: http://review.coreboot.org/#/c/4514/ | * The code has been merged into coreboot master: | * The code has been merged into coreboot master:}}

 $ git clone https://review.coreboot.org/coreboot.git


Flashing

Flash in X201 is divided roughly in 4 parts:

  • Descriptor (12K)
  • ME firmware (5M-12K)
  • Rewriteable flash (3M-96K)
  • Locked bootblock (96K)

Descriptor and bootblock are read-only. ME firmware is not readable. Rewriteable region can be rewritten easily with flashrom.

For coreboot we need to preserve descriptor and ME firmware while overwriting rewriteable region and bootblock. To achieve this there are 2 ways:

  • External flasher.
  • Unlock bootblock

For the first one proceeds as follows:

  • Turn off your laptop, remove battery and AC adapter.
  • Remove the keyboard.
  • Connect your external SPI flasher to the SPI chip which is under keyboard,

around the position of trackpoint under protective layer.

found it!
under the keyboard
The flash chip

I recommend using SOIC-8 clip. Depending on the flasher you use, you may have to use separate 3.3V source. Make sure not to feed more than 3.3V ot the chip. I used buspirate as flasher and 3.3V power lines from another computer. The pinout is as follows, the colors are buspirate colors

 ===  front (display) ====
 3.3V (red)   N/C          violet (CLK)  MOSI (gray)
      |        |             |              |
 dot  |        |             |              |
 CS (white)   MISO (black) N/C           ground (brown)
 ===  back (touchpad) ===
  • Read the flash. Twice. Compare the files to be sure. Save a copy of it on

external media.

flashrom -p <yourprogrammer> -r flash.bin
flashrom -p <yourprogrammer> -r flash2.bin
diff flash.bin flash2.bin

If you have trouble reading the chip successfully, the most common problems are

  • insufficient power supply
  • bad contacts
  • too long wires
  • bad pinout

The cable shipped with buspirate was too long, and needed to be trimmed.

See also In-System Programming


  • Recover descriptor and me firmare:
 dd if=flash.bin of=coreboot/3rdparty/mainboard/lenovo/x201/descriptor.bin \
   count=12288 bs=1M iflag=count_bytes
 dd if=flash.bin of=coreboot/3rdparty/mainboard/lenovo/x201/me.bin \
   skip=12288 count=5230592 bs=1M iflag=count_bytes,skip_bytes
  • Compile coreboot. Remember to enable HAVE_IFD and HAVE_ME_BIN
  • Flash the resulting build/coreboot.rom

The other way has never been successfully used but it's known that the locking mechanism is in bootblock itself and that original firmware has a way to update it as follows:

  • Flash an update of rewriteable region. On next boot bootblock parses the

image and sees that it contains a compressed copy of new bootblock. That copy is uncompressed and flashed. A way to unlock the bootblock would be to modify a firmware update to have a copy of bootblock without protection. For this you need to compress the modified block to fit into original space. The compression used is Lempel-Ziv- Huffman variant. I've written a compressor for it but unfortunately it's not performant enough.


identify the regions

[root@x201 ~]# flashrom -r bios.bin -pinternal:laptop=force_I_want_a_brick
flashrom v0.9.6.1-r1563 on Linux 3.10-1-grml-amd64 (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org

Calibrating delay loop... OK.
Found chipset "Intel QM57". Enabling flash write... WARNING: SPI Configuration Lockdown activated.
FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only.
FREG2: WARNING: Management Engine region (0x00003000-0x004fffff) is locked.
PR0: WARNING: 0x007d0000-0x01ffffff is read-only.
Please send a verbose log to flashrom@flashrom.org if this board is not listed on
http://flashrom.org/Supported_hardware#Supported_mainboards yet.
Writes have been disabled. You can enforce write support with the
ich_spi_force programmer option, but it will most likely harm your hardware!
If you force flashrom you will get no support if something breaks.
OK.
Found Macronix flash chip "MX25L6405" (8192 kB, SPI) at physical address 0xff800000.
Reading flash... FAILED.

it will print the ME regions:

FREG2: WARNING: Management Engine region (0x00003000-0x004fffff) is locked.

it will also print the chip:

Found Macronix flash chip "MX25L6405" (8192 kB, SPI) at physical address 0xff800000.

But as in this case, flashrom might misidentify the chip, this output is from this MX25L6445E

visually verify your chip's part number and find an appropriate datasheet

=>verify that its voltage matches with the programmer voltage...

  • Use flashrom layouts:
       -l, --layout <file>

X201 Layout

000000000:00000fff fd
000001000:00002fff gbe
000003000:004fffff me
000500000:007fffff bios

To flash only the bios partition (coreboot) do:

flashrom -l <layout> -i bios -w coreboot.rom