Difference between revisions of "HP COMPAQ NC6320"

Revision as of 18:42, 17 January 2013

Status

Nothing work yet, no output on serial.

Hardware

• CPU: T7200
• Northbridge: 945GM
• Southbridge: ICH7-M
• superio: SMSC LPC47N217
• ec: SMSC LPC47N217
• flash chip: M25PE80,1024 kB, soldered,SOIC-8

How to flash

• disassemble the laptop
• Put the power adapter in the laptop's power plug
• power off the laptop
• attach the pomona clip and flash(backup the BIOS before.)

how to unpack the BIOS

See http://paste.flashrom.org/view.php?id=1523

Ec Issue

The ec firmware(4000_KBC.bin) probably has to be in the image at the same fixed position than the BIOS.

LPC

# lspci -nnvvvxxx -s 00:1f.0
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 01)
	Subsystem: Hewlett-Packard Company Device [103c:30aa]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-INTx-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information: Len=0c <?>
	Kernel modules: leds-ss4200, iTCO_wdt, intel-rng
00: 86 80 b9 27 07 00 10 02 01 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 aa 30
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
40: 01 10 00 00 80 00 00 00 01 11 00 00 10 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 80 80 80 80 92 00 00 00 80 80 80 80 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 10 00 05 3c 01 05 7c 00 00 00 00 00 00 00 00 00
90: 39 02 04 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 24 06 00 00 e1 00 00 00 13 1c 0a 00 00 03 00 00
b0: 00 00 f0 00 00 00 00 00 08 60 60 91 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 33 22 11 00 67 45 00 00 00 c0 00 00 00 00 00 00
e0: 09 00 0c 10 b4 02 24 17 00 00 00 00 00 00 00 00
f0: 01 00 d9 fe 00 00 00 00 86 0f 02 00 00 00 00 00

Patch (not working)

The nc6320 is very similar to the Roda rk886ex, with only the superio that is different.

From c9e8a0dbc5519024be2acc5877c4f2b62a0461d6 Mon Sep 17 00:00:00 2001
From: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Date: Mon, 14 Jan 2013 00:28:07 +0100
Subject: [PATCH] Changes for nc6320

Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
---
 src/mainboard/roda/rk886ex/Kconfig       |  2 +-
 src/mainboard/roda/rk886ex/devicetree.cb |  2 +-
 src/mainboard/roda/rk886ex/romstage.c    | 92 +++++++-------------------------
 3 files changed, 20 insertions(+), 76 deletions(-)

diff --git a/src/mainboard/roda/rk886ex/Kconfig b/src/mainboard/roda/rk886ex/Kconfig
index 84a8543..0095f4d 100644
--- a/src/mainboard/roda/rk886ex/Kconfig
+++ b/src/mainboard/roda/rk886ex/Kconfig
@@ -8,7 +8,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy
 	select NORTHBRIDGE_INTEL_SUBTYPE_I945GM
 	select SOUTHBRIDGE_INTEL_I82801GX
 	select SOUTHBRIDGE_TI_PCI7420
-	select SUPERIO_SMSC_LPC47N227
+	select SUPERIO_SMSC_LPC47N217
 	select SUPERIO_RENESAS_M3885X
 	select EC_ACPI
 	select HAVE_OPTION_TABLE
diff --git a/src/mainboard/roda/rk886ex/devicetree.cb b/src/mainboard/roda/rk886ex/devicetree.cb
index aadba9d..955561a 100644
--- a/src/mainboard/roda/rk886ex/devicetree.cb
+++ b/src/mainboard/roda/rk886ex/devicetree.cb
@@ -83,7 +83,7 @@ chip northbridge/intel/i945
 			#device pci 1e.2 off end # AC'97 Audio
 			#device pci 1e.3 off end # AC'97 Modem
                         device pci 1f.0 on # LPC bridge
-                                chip superio/smsc/lpc47n227
+                                chip superio/smsc/lpc47n217
 					device pnp 2e.1 on # Parallel port
 						 io 0x60 = 0x378
 						irq 0x70 = 5
diff --git a/src/mainboard/roda/rk886ex/romstage.c b/src/mainboard/roda/rk886ex/romstage.c
index d75d33f..8be7b4e 100644
--- a/src/mainboard/roda/rk886ex/romstage.c
+++ b/src/mainboard/roda/rk886ex/romstage.c
@@ -35,6 +35,7 @@
 #include "northbridge/intel/i945/i945.h"
 #include "northbridge/intel/i945/raminit.h"
 #include "southbridge/intel/i82801gx/i82801gx.h"
+#include "superio/smsc/lpc47n217/early_serial.c"
 #include "option_table.h"
 
 void setup_ich7_gpios(void)
@@ -68,82 +69,35 @@ void setup_ich7_gpios(void)
 
 static void ich7_enable_lpc(void)
 {
-	int lpt_en = 0;
-	if (read_option(lpt, 0) != 0) {
-	       lpt_en = 1<<2; // enable LPT
-	}
 	// Enable Serial IRQ
 	pci_write_config8(PCI_DEV(0, 0x1f, 0), 0x64, 0xd0);
 	// decode range
-	pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x80, 0x0007);
+	pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x80, 0x8);
 	// decode range
-	pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x82, 0x3f0b | lpt_en);
-	// Enable 0x02e0
-	pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x84, 0x02e1);
+	pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x82, 0x2001); //CNF2_LPC_EN| lpt_en);
+	// Enable 0x04e0
+	pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x84, 0x34e1);
 	pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x86, 0x001c);
 	// COM3 decode
-	pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x88, 0x00fc0601);
+	//pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x88, 0x00fc0601);
 	// COM4 decode
-	pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x8c, 0x00040069);
-}
-
-/* This box has two superios, so enabling serial becomes slightly excessive.
- * We disable a lot of stuff to make sure that there are no conflicts between
- * the two. Also set up the GPIOs from the beginning. This is the "no schematic
- * but safe anyways" method.
- */
-static inline void pnp_enter_ext_func_mode(device_t dev)
-{
-	unsigned int port = dev >> 8;
-	outb(0x55, port);
+	//pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x8c, 0x00040069);
 }
 
-static void pnp_exit_ext_func_mode(device_t dev)
-{
-	unsigned int port = dev >> 8;
-	outb(0xaa, port);
-}
-
-static void pnp_write_register(device_t dev, int reg, int val)
-{
-	unsigned int port = dev >> 8;
-	outb(reg, port);
-	outb(val, port+1);
-}
 
 static void early_superio_config(void)
 {
-	device_t dev;
-
-	dev=PNP_DEV(0x2e, 0x00);
-
-	pnp_enter_ext_func_mode(dev);
-	pnp_write_register(dev, 0x01, 0x94); // Extended Parport modes
-	pnp_write_register(dev, 0x02, 0x88); // UART power on
-	pnp_write_register(dev, 0x03, 0x72); // Floppy
-	pnp_write_register(dev, 0x04, 0x01); // EPP + SPP
-	pnp_write_register(dev, 0x14, 0x03); // Floppy
-	pnp_write_register(dev, 0x20, (0x3f0 >> 2)); // Floppy
-	pnp_write_register(dev, 0x23, (0x378 >> 2)); // PP base
-	pnp_write_register(dev, 0x24, (0x3f8 >> 2)); // UART1 base
-	pnp_write_register(dev, 0x25, (0x2f8 >> 2)); // UART2 base
-	pnp_write_register(dev, 0x26, (2 << 4) | 0); // FDC + PP DMA
-	pnp_write_register(dev, 0x27, (6 << 4) | 7); // FDC + PP DMA
-	pnp_write_register(dev, 0x28, (4 << 4) | 3); // UART1,2 IRQ
-	/* These are the SMI status registers in the SIO: */
-	pnp_write_register(dev, 0x30, (0x600 >> 4)); // Runtime Register Block Base
-
-	pnp_write_register(dev, 0x31, 0x00); // GPIO1 DIR
-	pnp_write_register(dev, 0x32, 0x00); // GPIO1 POL
-	pnp_write_register(dev, 0x33, 0x40); // GPIO2 DIR
-	pnp_write_register(dev, 0x34, 0x00); // GPIO2 POL
-	pnp_write_register(dev, 0x35, 0xff); // GPIO3 DIR
-	pnp_write_register(dev, 0x36, 0x00); // GPIO3 POL
-	pnp_write_register(dev, 0x37, 0xe0); // GPIO4 DIR
-	pnp_write_register(dev, 0x38, 0x00); // GPIO4 POL
-	pnp_write_register(dev, 0x39, 0x80); // GPIO4 POL
-
-	pnp_exit_ext_func_mode(dev);
+	/* Found SMSC LPC47N217 (id=0x7a, rev=0x01) at 0x4e */
+	device_t dev = PNP_DEV(0x4e, LPC47N217_SP1);
+	lpc47n217_enable_serial(dev, CONFIG_TTYS0_BASE);
+//	uart_init();
+#if 0
+	outb(0x24, 0xcd6);
+	outb(0x1, 0xcd7);
+	outb(0xea, 0xcd6);
+	outb(0x1, 0xcd7);
+	*(u8 *)0xfed80101 = 0x98;
+#endif
 }
 
 static void rcba_config(void)
@@ -243,13 +197,6 @@ static void early_ich7_init(void)
 	RCBA32(0x2034) = reg32;
 }
 
-static void init_artec_dongle(void)
-{
-	// Enable 4MB decoding
-	outb(0xf1, 0x88);
-	outb(0xf4, 0x88);
-}
-
 #include <cbmem.h>
 
 void main(unsigned long bist)
@@ -285,9 +232,6 @@ void main(unsigned long bist)
 	 */
 	i945_early_initialization();
 
-	/* This has to happen after i945_early_initialization() */
-	init_artec_dongle();
-
 	/* Read PM1_CNT */
 	reg32 = inl(DEFAULT_PMBASE + 0x04);
 	printk(BIOS_DEBUG, "PM1_CNT: %08x\n", reg32);
-- 
1.8.1

grub in BIOS

lspci is incomplete:

grub> lspci -i
00:00.0 8086:27a0 [0600] Host Bridge
00:02.0 8086:27a2 [0300] VGA Controller
        32-bit memory space 0 at 0x00000000e8400000 [non-prefetchable]
        IO space 1 at 0x6000
        32-bit memory space 2 at 0x00000000d0000000 [prefetchable]
        32-bit memory space 3 at 0x00000000e8480000 [non-prefetchable]
00:02.1 8086:27a6 [0380] Display Controller
        32-bit memory space 0 at 0x00000000e8500000 [non-prefetchable]
00:1b.0 8086:27d8 [0403] Multimedia device
        64-bit memory space 0 at 0x00000000e8580000 [non-prefetchable]
00:1c.0 8086:27d0 [0604] PCI-PCI Bridge
        32-bit memory space 2 at 0x0000000000080800 [non-prefetchable]
        32-bit memory space 3 at 0x00000000000000f0 [non-prefetchable]
        32-bit memory space 4 at 0x00000000e800e800 [non-prefetchable]
        IO space 5 at 0x1fff0
00:1c.2 8086:27d4 [0604] PCI-PCI Bridge
        32-bit memory space 2 at 0x0000000000181800 [non-prefetchable]
        32-bit memory space 3 at 0x0000000020005040 [non-prefetchable]
        32-bit memory space 4 at 0x00000000e7f0e400 [non-prefetchable]
        IO space 5 at 0x1fff0
00:1c.3 8086:27d6 [0604] PCI-PCI Bridge
        32-bit memory space 2 at 0x0000000000202000 [non-prefetchable]
        32-bit memory space 3 at 0x0000000020003020 [non-prefetchable]
        32-bit memory space 4 at 0x00000000e3f0e000 [non-prefetchable]
        IO space 5 at 0x1fff0
00:1d.0 8086:27c8 [0c03] USB Controller
        IO space 4 at 0x6020
00:1d.1 8086:27c9 [0c03] USB Controller
        IO space 4 at 0x6040
00:1d.2 8086:27ca [0c03] USB Controller
        IO space 4 at 0x6060
00:1d.3 8086:27cb [0c03] USB Controller
        IO space 4 at 0x6080
00:1d.7 8086:27cc [0c03] USB Controller [PI 20]
        32-bit memory space 0 at 0x00000000e8584000 [non-prefetchable]
00:1e.0 8086:2448 [0604] PCI-PCI Bridge [PI 01]
        32-bit memory space 2 at 0x0000000020030200 [non-prefetchable]
        32-bit memory space 3 at 0x00000000228000f0 [non-prefetchable]
        32-bit memory space 4 at 0x00000000e830e810 [non-prefetchable]
        IO space 5 at 0x1fff0
00:1f.0 8086:27b9 [0601] ISA Bridge
00:1f.1 8086:27df [0101] IDE Controller [PI 8a]
        IO space 0 at 0x0
        IO space 1 at 0x0
        IO space 2 at 0x0
        IO space 3 at 0x0
        IO space 4 at 0x60a0
00:1f.2 8086:27c5 [0106] SATA Controller [PI 01]
        IO space 0 at 0x13f0
        IO space 1 at 0x15f4
        IO space 2 at 0x1370
        IO space 3 at 0x1574
        IO space 4 at 0x60d0
        32-bit memory space 5 at 0x00000000e8585000 [non-prefetchable]
02:06.0 104c:8039 [0607] CardBus Bridge
        32-bit memory space 0 at 0x00000000e8100000 [non-prefetchable]
        32-bit memory space 1 at 0x00000000020000a0 [non-prefetchable]
        32-bit memory space 2 at 0x0000000000030300 [non-prefetchable]
02:06.1 104c:803a [0c00] Serial Bus Controller [PI 10]
        32-bit memory space 0 at 0x00000000e8101000 [non-prefetchable]
        32-bit memory space 1 at 0x00000000e8104000 [non-prefetchable]
02:06.2 104c:803b [0180] Mass storage Controller
        32-bit memory space 0 at 0x00000000e8108000 [non-prefetchable]
02:06.3 104c:803c [0805] System hardware
        32-bit memory space 0 at 0x00000000e8109000 [non-prefetchable]
02:06.4 104c:803d [0780] Communication controller
        32-bit memory space 0 at 0x00000000e810a000 [non-prefetchable]
        32-bit memory space 1 at 0x00000000e810b000 [non-prefetchable]
02:0e.0 14e4:169c [0200] Ethernet Controller
        32-bit memory space 0 at 0x00000000e8110000 [non-prefetchable]
08:00.0 8086:4222 [0280] Network controller
        32-bit memory space 0 at 0x00000000e8000000 [non-prefetchable]

but:

grub> setpci -s 00:1f.0 0.W
Register 0 of 0:31.0 is 8086

small python helper

$ cat coreboothelper.py 
#! /usr/bin/env python
def PCI_DEV(SEGBUS, DEV, FN):
    return ((((SEGBUS) & 0xFFF) << 20) | (((DEV) & 0x1F) << 15) | (((FN)  & 0x07) << 12)) 

def pci_write_config8(dev,where,value):
    addr = (dev>>4) | where
    print "outl({0:#x});".format(0x80000000 | (addr & ~3), 0xCF8)
    print "outb({0:#x});".format(value, 0xCFC + (addr & 3))

$ python
Python 2.7.3 (default, Dec 22 2012, 21:27:36) 
[GCC 4.7.2] on linux2
Type "help", "copyright", "credits" or "license" for more information.
>>> from coreboothelper import *
>>> pci_write_config8(PCI_DEV(0, 0x1f, 0),0x64, 0x92)
outl(0x8000f864);
outb(0x92);