Board:kontron/986lcd-m

From coreboot
Revision as of 18:23, 16 December 2008 by Uwe (Talk | contribs)

Jump to: navigation, search

This page describes how to use coreboot on the Kontron 986LCD-M/mITX mainboard. It is maintained by Uwe Hermann.

Status

Device/functionality Status Comments
CPU
CPU works OK Intel(R) Core(TM)2 CPU T5300 @ 1.73GHz (dual core)
L1 cache enabled OK CPU: L1 I cache: 32K, L1 D cache: 32K
L2 cache enabled OK L2 cache: 2048K
L3 cache enabled N/A
Multiple CPU support N/A
Multi-core support OK Both cores show up in /proc/cpuinfo.
Hardware virtualization  ?
RAM
EDO N/A
SDRAM N/A
SO-DIMM N/A
DDR N/A
DDR2 OK Works fine, but currently you need to populate both RAM slots with DIMMs (of the same size?).
DDR3 N/A
Dual channel support N/A
ECC support  ?
On-board Hardware
On-board IDE 3.5" OK
On-board IDE 2.5" N/A
On-board SATA  ?
On-board SCSI N/A
On-board USB OK Tested: USB thumb drive in all 4 backpanel USB ports. The onboard USB pin headers are untested, but should also work.
On-board VGA  ?
On-board ethernet  ?
On-board audio  ?
On-board modem  ?
On-board FireWire  ?
On-board smartcard reader N/A
On-board CompactFlash N/A
On-board PCMCIA N/A
Add-on slots/cards
ISA add-on cards N/A
Audio/Modem-Riser (AMR/CNR) cards N/A
PCI add-on cards  ?
Mini-PCI add-on cards Unknown
PCI-X add-on cards Unknown
AGP graphics cards N/A
PCI Express x1 add-on cards N/A
PCI Express x2 add-on cards N/A
PCI Express x4 add-on cards N/A
PCI Express x8 add-on cards N/A
PCI Express x16 add-on cards  ?
PCI Express x32 add-on cards N/A
HTX add-on cards N/A
Legacy / Super I/O
Floppy  ?
Serial port 1 (COM1) OK
Serial port 2 (COM2)  ?
Parallel port OK Doing modprobe ppdev works, but no further test were performed.
PS/2 keyboard OK
PS/2 mouse  ?
Game port N/A
Infrared  ?
PC speaker OK
DiskOnChip N/A
Miscellaneous
Sensors / fan control OK Works fine using the w83627hf and coretemp Linux kernel modules.
Hardware watchdog OK Not yet actually tested, but it seems to be found: iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0560).
SMBus  ?
CAN bus N/A
CPU frequency scaling  ?
Other powersaving features N/A
ACPI  ?
Reboot  ?
Poweroff  ? Needs ACPI, thus won't work if you use acpi=off on the Linux kernel command line.
Suspend Unknown
Nonstandard LEDs  ?
High precision event timers (HPET) OK The HPET is detected by Linux (hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0) and powertop output suggests that it works ok.
Random number generator (RNG) N/A
Wake on modem ring  ?
Wake on LAN  ?
Wake on keyboard  ?
Wake on mouse  ?
Flashrom OK Works fine, but you have to use -m kontron:986lcd-m when booted with the vendor BIOS (not needed when booted with coreboot).

Build tutorial

$ svn co svn://coreboot.org/repos/trunk/coreboot-v2
$ cd coreboot-v2/targets
$ ./buildtarget kontron/986lcd-m
$ cd kontron/986lcd-m/kontron_986lcd_m

Now copy your payload into the current directory and name it payload.elf. Then:

$ make -s

The resulting coreboot.rom is your coreboot ROM image you can flash using flashrom.

Notes

  • If you use FILO, SATA will probably be hda and hdb, while hdc is the master drive of the IDE controller.
  • Currently you have to use acpi=off on the kernel command line to make IDE work.
  • If you experience kernel crashes try to blacklist the agpgart and intel_agp kernel modules.
Public domain I, the copyright holder of this work, hereby release it into the public domain. This applies worldwide.

In case this is not legally possible:
I grant anyone the right to use this work for any purpose, without any conditions, unless such conditions are required by law.