[coreboot-gerrit] New patch to review for coreboot: 771a427 Drop Intel E7501 / i82801ex and Tyan s2735
Stefan Reinauer (stefan.reinauer@coreboot.org)
gerrit at coreboot.org
Tue Feb 10 21:24:02 CET 2015
Stefan Reinauer (stefan.reinauer at coreboot.org) just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/8406
-gerrit
commit 771a427b10318e93d707ace0acfc35c493f37497
Author: Stefan Reinauer <stefan.reinauer at coreboot.org>
Date: Tue Feb 10 21:22:36 2015 +0100
Drop Intel E7501 / i82801ex and Tyan s2735
Change-Id: I0830d0f54189e855ef14b0d84bed74ba41b84efb
Signed-off-by: Stefan Reinauer <stefan.reinauer at coreboot.org>
---
src/mainboard/tyan/Kconfig | 3 -
src/mainboard/tyan/s2735/Kconfig | 41 -
src/mainboard/tyan/s2735/board_info.txt | 3 -
src/mainboard/tyan/s2735/cmos.layout | 82 --
src/mainboard/tyan/s2735/devicetree.cb | 86 --
src/mainboard/tyan/s2735/irq_tables.c | 45 -
src/mainboard/tyan/s2735/mptable.c | 130 --
src/mainboard/tyan/s2735/romstage.c | 76 -
src/northbridge/intel/Kconfig | 1 -
src/northbridge/intel/Makefile.inc | 1 -
src/northbridge/intel/e7501/Kconfig | 5 -
src/northbridge/intel/e7501/Makefile.inc | 1 -
src/northbridge/intel/e7501/debug.c | 275 ----
src/northbridge/intel/e7501/e7501.h | 79 -
src/northbridge/intel/e7501/northbridge.c | 140 --
src/northbridge/intel/e7501/raminit.c | 2007 --------------------------
src/northbridge/intel/e7501/raminit.h | 20 -
src/northbridge/intel/e7501/reset_test.c | 18 -
src/southbridge/intel/Kconfig | 1 -
src/southbridge/intel/Makefile.inc | 1 -
src/southbridge/intel/i82801ex/Kconfig | 14 -
src/southbridge/intel/i82801ex/Makefile.inc | 11 -
src/southbridge/intel/i82801ex/ac97.c | 37 -
src/southbridge/intel/i82801ex/chip.h | 34 -
src/southbridge/intel/i82801ex/early_smbus.c | 130 --
src/southbridge/intel/i82801ex/ehci.c | 51 -
src/southbridge/intel/i82801ex/i82801ex.c | 48 -
src/southbridge/intel/i82801ex/i82801ex.h | 22 -
src/southbridge/intel/i82801ex/ide.c | 42 -
src/southbridge/intel/i82801ex/lpc.c | 381 -----
src/southbridge/intel/i82801ex/pci.c | 44 -
src/southbridge/intel/i82801ex/reset.c | 8 -
src/southbridge/intel/i82801ex/sata.c | 59 -
src/southbridge/intel/i82801ex/smbus.c | 48 -
src/southbridge/intel/i82801ex/smbus.h | 104 --
src/southbridge/intel/i82801ex/uhci.c | 55 -
src/southbridge/intel/i82801ex/watchdog.c | 28 -
37 files changed, 4131 deletions(-)
diff --git a/src/mainboard/tyan/Kconfig b/src/mainboard/tyan/Kconfig
index 4a135bd..fb16996 100644
--- a/src/mainboard/tyan/Kconfig
+++ b/src/mainboard/tyan/Kconfig
@@ -23,8 +23,6 @@ choice
config BOARD_TYAN_S1846
bool "S1846 (Tsunami ATX)"
-config BOARD_TYAN_S2735
- bool "S2735 (Tiger i7501R)"
config BOARD_TYAN_S2850
bool "S2850 (Tomcat K8S)"
config BOARD_TYAN_S2875
@@ -56,7 +54,6 @@ config BOARD_TYAN_S8226
endchoice
source "src/mainboard/tyan/s1846/Kconfig"
-source "src/mainboard/tyan/s2735/Kconfig"
source "src/mainboard/tyan/s2850/Kconfig"
source "src/mainboard/tyan/s2875/Kconfig"
source "src/mainboard/tyan/s2880/Kconfig"
diff --git a/src/mainboard/tyan/s2735/Kconfig b/src/mainboard/tyan/s2735/Kconfig
deleted file mode 100644
index a64c0e3..0000000
--- a/src/mainboard/tyan/s2735/Kconfig
+++ /dev/null
@@ -1,41 +0,0 @@
-if BOARD_TYAN_S2735
-
-config BOARD_SPECIFIC_OPTIONS # dummy
- def_bool y
- select CPU_INTEL_SOCKET_MPGA604
- select NORTHBRIDGE_INTEL_E7501
- select SOUTHBRIDGE_INTEL_I82870
- select SOUTHBRIDGE_INTEL_I82801EX
- select SUPERIO_WINBOND_W83627HF
- select HAVE_PIRQ_TABLE
- select HAVE_MP_TABLE
- select UDELAY_TSC
- select HAVE_OPTION_TABLE
- select USE_WATCHDOG_ON_BOOT
- select BOARD_ROMSIZE_KB_512
-
-config MAINBOARD_DIR
- string
- default tyan/s2735
-
-config DCACHE_RAM_BASE
- hex
- default 0xcf000
-
-config DCACHE_RAM_SIZE
- hex
- default 0x1000
-
-config MAINBOARD_PART_NUMBER
- string
- default "S2735"
-
-config IRQ_SLOT_COUNT
- int
- default 15
-
-config MAX_CPUS
- int
- default 4
-
-endif # BOARD_TYAN_S2735
diff --git a/src/mainboard/tyan/s2735/board_info.txt b/src/mainboard/tyan/s2735/board_info.txt
deleted file mode 100644
index 3eb1393..0000000
--- a/src/mainboard/tyan/s2735/board_info.txt
+++ /dev/null
@@ -1,3 +0,0 @@
-Board name: Tiger i7501R (S2735)
-Category: server
-Board URL: http://www.tyan.com/archive/products/html/tigeri7501r.html
diff --git a/src/mainboard/tyan/s2735/cmos.layout b/src/mainboard/tyan/s2735/cmos.layout
deleted file mode 100644
index 58585a2..0000000
--- a/src/mainboard/tyan/s2735/cmos.layout
+++ /dev/null
@@ -1,82 +0,0 @@
-entries
-
-#start-bit length config config-ID name
-#0 8 r 0 seconds
-#8 8 r 0 alarm_seconds
-#16 8 r 0 minutes
-#24 8 r 0 alarm_minutes
-#32 8 r 0 hours
-#40 8 r 0 alarm_hours
-#48 8 r 0 day_of_week
-#56 8 r 0 day_of_month
-#64 8 r 0 month
-#72 8 r 0 year
-#80 4 r 0 rate_select
-#84 3 r 0 REF_Clock
-#87 1 r 0 UIP
-#88 1 r 0 auto_switch_DST
-#89 1 r 0 24_hour_mode
-#90 1 r 0 binary_values_enable
-#91 1 r 0 square-wave_out_enable
-#92 1 r 0 update_finished_enable
-#93 1 r 0 alarm_interrupt_enable
-#94 1 r 0 periodic_interrupt_enable
-#95 1 r 0 disable_clock_updates
-#96 288 r 0 temporary_filler
-0 384 r 0 reserved_memory
-384 1 e 4 boot_option
-385 1 e 4 last_boot
-386 1 e 1 ECC_memory
-388 4 r 0 reboot_bits
-392 3 e 5 baud_rate
-395 1 e 2 hyper_threading
-396 1 e 1 thermal_monitoring
-397 1 e 1 remap_memory_high
-400 1 e 1 power_on_after_fail
-412 4 e 6 debug_level
-416 4 e 7 boot_first
-420 4 e 7 boot_second
-424 4 e 7 boot_third
-428 4 h 0 boot_index
-432 8 h 0 boot_countdown
-#440 4 e 9 slow_cpu
-444 1 e 1 nmi
-728 256 h 0 user_data
-984 16 h 0 check_sum
-# Reserve the extended AMD configuration registers
-1000 24 r 0 amd_reserved
-
-
-
-enumerations
-
-#ID value text
-1 0 Disable
-1 1 Enable
-2 0 Enable
-2 1 Disable
-4 0 Fallback
-4 1 Normal
-5 0 115200
-5 1 57600
-5 2 38400
-5 3 19200
-5 4 9600
-5 5 4800
-5 6 2400
-5 7 1200
-6 6 Notice
-6 7 Info
-6 8 Debug
-6 9 Spew
-7 0 Network
-7 1 HDD
-7 2 Floppy
-7 8 Fallback_Network
-7 9 Fallback_HDD
-7 10 Fallback_Floppy
-#7 3 ROM
-
-checksums
-
-checksum 392 983 984
diff --git a/src/mainboard/tyan/s2735/devicetree.cb b/src/mainboard/tyan/s2735/devicetree.cb
deleted file mode 100644
index d3b6b1e..0000000
--- a/src/mainboard/tyan/s2735/devicetree.cb
+++ /dev/null
@@ -1,86 +0,0 @@
-chip northbridge/intel/e7501
- device domain 0 on
- subsystemid 0x10f1 0x2735 inherit
- device pci 0.0 on end
- device pci 0.1 on end
- device pci 2.0 on
- chip southbridge/intel/i82870
- device pci 1c.0 on end
- device pci 1d.0 on
- device pci 1.0 on end # intel lan
- device pci 1.1 on end
- end
- device pci 1e.0 on end
- device pci 1f.0 on end
- end
- end
- device pci 6.0 on end
- chip southbridge/intel/i82801ex
- device pci 1d.0 on end
- device pci 1d.1 on end
- device pci 1d.2 on end
- device pci 1d.3 on end
- device pci 1d.7 on end
- device pci 1e.0 on
- device pci 1.0 on end # intel lan 10/100
- device pci 2.0 on end # ati
- end
- device pci 1f.0 on
- chip superio/winbond/w83627hf
- device pnp 2e.0 on # Floppy
- io 0x60 = 0x3f0
- irq 0x70 = 6
- drq 0x74 = 2
- end
- device pnp 2e.1 off # Parallel Port
- io 0x60 = 0x378
- irq 0x70 = 7
- end
- device pnp 2e.2 on # Com1
- io 0x60 = 0x3f8
- irq 0x70 = 4
- end
- device pnp 2e.3 on # Com2
- io 0x60 = 0x2f8
- irq 0x70 = 3
- end
- device pnp 2e.5 on # Keyboard
- io 0x60 = 0x60
- io 0x62 = 0x64
- irq 0x70 = 1
- irq 0x72 = 12
- end
- device pnp 2e.6 off # CIR
- io 0x60 = 0x100
- end
- device pnp 2e.7 off # GAME_MIDI_GIPO1
- io 0x60 = 0x220
- io 0x62 = 0x300
- irq 0x70 = 9
- end
- device pnp 2e.8 off end # GPIO2
- device pnp 2e.9 off end # GPIO3
- device pnp 2e.a off end # ACPI
- device pnp 2e.b on # HW Monitor
- io 0x60 = 0x290
- irq 0x70 = 5
- end
- end
- end
- device pci 1f.1 off end
- device pci 1f.2 on end
- device pci 1f.3 on end
- device pci 1f.5 off end
- device pci 1f.6 off end
- end # SB
- end # PCI domain
- device cpu_cluster 0 on
- chip cpu/intel/socket_mPGA604
- device lapic 0 on end
- end
- chip cpu/intel/socket_mPGA604
- device lapic 6 on end
- end
- end
-end
-
diff --git a/src/mainboard/tyan/s2735/irq_tables.c b/src/mainboard/tyan/s2735/irq_tables.c
deleted file mode 100644
index 3d69b49..0000000
--- a/src/mainboard/tyan/s2735/irq_tables.c
+++ /dev/null
@@ -1,45 +0,0 @@
-/* This file was generated by getpir.c, do not modify!
- (but if you do, please run checkpir on it to verify)
- Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up
-
- Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
-*/
-
-#include <arch/pirq_routing.h>
-
-static const struct irq_routing_table intel_irq_routing_table = {
- PIRQ_SIGNATURE, /* u32 signature */
- PIRQ_VERSION, /* u16 version */
- 32+16*CONFIG_IRQ_SLOT_COUNT, /* there can be total CONFIG_IRQ_SLOT_COUNT devices on the bus */
- 0x00, /* Where the interrupt router lies (bus) */
- (0x1f<<3)|0x0, /* Where the interrupt router lies (dev) */
- 0, /* IRQs devoted exclusively to PCI usage */
- 0x8086, /* Vendor */
- 0x24d0, /* Device */
- 0, /* Miniport data */
- { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
- 0x9a, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
- {
- /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
- {0x04,(0x08<<3)|0x0, {{0x68, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x00,(0x1f<<3)|0x0, {{0x62, 0xdcf8}, {0x61, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x00,(0x1d<<3)|0x0, {{0x60, 0xdcf8}, {0x63, 0xdcf8}, {0x62, 0xdcf8}, {0x6b, 0x0dcf8}}, 0x0, 0x0},
- {0x04,(0x03<<3)|0x0, {{0x62, 0xdcf8}, {0x63, 0xdcf8}, {0x60, 0xdcf8}, {0x61, 0x0dcf8}}, 0x3, 0x0},
- {0x04,(0x02<<3)|0x0, {{0x62, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x03,(0x1f<<3)|0x0, {{0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x02,(0x1f<<3)|0x0, {{0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x03,(0x03<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x1, 0x0},
- {0x03,(0x06<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x2, 0x0},
- {0x02,(0x01<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x02,(0x02<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x04,(0x01<<3)|0x0, {{0x61, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x04,(0x04<<3)|0x0, {{0x63, 0xdcf8}, {0x60, 0xdcf8}, {0x61, 0xdcf8}, {0x62, 0x0dcf8}}, 0x4, 0x0},
- {0x03,(0x04<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x5, 0x0},
- {0x03,(0x05<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x6, 0x0},
- }
-};
-
-unsigned long write_pirq_routing_table(unsigned long addr)
-{
- return copy_pirq_routing_table(addr, &intel_irq_routing_table);
-}
diff --git a/src/mainboard/tyan/s2735/mptable.c b/src/mainboard/tyan/s2735/mptable.c
deleted file mode 100644
index 9073728..0000000
--- a/src/mainboard/tyan/s2735/mptable.c
+++ /dev/null
@@ -1,130 +0,0 @@
-#include <console/console.h>
-#include <arch/smp/mpspec.h>
-#include <arch/ioapic.h>
-#include <device/pci.h>
-#include <string.h>
-#include <stdint.h>
-
-static void *smp_write_config_table(void *v)
-{
- struct mp_config_table *mc;
- int isa_bus;
-
- mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN);
-
- mptable_init(mc, LOCAL_APIC_ADDR);
-
- smp_write_processors(mc);
- mptable_write_buses(mc, NULL, &isa_bus);
-/*I/O APICs: APIC ID Version State Address*/
- smp_write_ioapic(mc, 8, 0x20, IO_APIC_ADDR);
- {
- device_t dev;
- struct resource *res;
- dev = dev_find_slot(1, PCI_DEVFN(0x1e,0));
- if (dev) {
- res = find_resource(dev, PCI_BASE_ADDRESS_0);
- if (res) {
- smp_write_ioapic(mc, 0x09, 0x20, res->base);
- }
- }
- dev = dev_find_slot(1, PCI_DEVFN(0x1c,0));
- if (dev) {
- res = find_resource(dev, PCI_BASE_ADDRESS_0);
- if (res) {
- smp_write_ioapic(mc, 0x0a, 0x20, res->base);
- }
- }
- }
- mptable_add_isa_interrupts(mc, isa_bus, 0x8, 0);
-
-/*I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
-*/
-//USB
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x7c, 0x8, 0x12);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x7d, 0x8, 0x11);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x74, 0x8, 0x10);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x75, 0x8, 0x13);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x77, 0x8, 0x17);
-
-//onboard ati
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, 0x8, 0x8, 0x12);
-
-//onboard intel 82551 10/100
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, 0x4, 0x8, 0x11);
-
-// onboard Intel 82547 1000
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x4, 0xa, 0x0);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x5, 0xa, 0x1);
-
-//Slot 4
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|0, 0x8, 0x12);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|1, 0x8, 0x13);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|2, 0x8, 0x10);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|3, 0x8, 0x11);
-//Slot 3
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|0, 0x8, 0x13);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|1, 0x8, 0x10);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|2, 0x8, 0x11);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|3, 0x8, 0x12);
-//Slot 1
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|0, 0x9, 0x0);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|1, 0x9, 0x1);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|2, 0x9, 0x2);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|3, 0x9, 0x3);
-//Slot 2
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|0, 0x9, 0x4);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|1, 0x9, 0x5);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|2, 0x9, 0x6);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|3, 0x9, 0x7);
-
-/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/
- mptable_lintsrc(mc, 0x0);
-/*
-MP Config Extended Table Entries:
-
---
-System Address Space
- bus ID: 0 address type: I/O address
- address base: 0x9000
- address range: 0x6000
---
-System Address Space
- bus ID: 0 address type: I/O address
- address base: 0x0
- address range: 0x100
---
-System Address Space
- bus ID: 0 address type: memory address
- address base: 0xa0000
- address range: 0x20000
---
-System Address Space
- bus ID: 0 address type: memory address
- address base: 0xfc700000
- address range: 0x2500000
---
-System Address Space
- bus ID: 0 address type: prefetch address
- address base: 0xff600000
- address range: 0x500000
---
-Bus Heirarchy
- bus ID: 5 bus info: 0x01 parent bus ID: 0--
-Compatibility Bus Address
- bus ID: 0 address modifier: add
- predefined range: 0x00000000--
-Compatibility Bus Address
- bus ID: 0 address modifier: add
- predefined range: 0x00000001 // There is no extension information...
-*/
- /* Compute the checksums */
- return mptable_finalize(mc);
-}
-
-unsigned long write_smp_table(unsigned long addr)
-{
- void *v;
- v = smp_write_floating_table(addr, 0);
- return (unsigned long)smp_write_config_table(v);
-}
diff --git a/src/mainboard/tyan/s2735/romstage.c b/src/mainboard/tyan/s2735/romstage.c
deleted file mode 100644
index 5d4fd0e..0000000
--- a/src/mainboard/tyan/s2735/romstage.c
+++ /dev/null
@@ -1,76 +0,0 @@
-#include <stdint.h>
-#include <string.h>
-#include <device/pci_def.h>
-#include <arch/io.h>
-#include <device/pnp_def.h>
-#include <cpu/x86/lapic.h>
-#include <pc80/mc146818rtc.h>
-#include <console/console.h>
-#include <lib.h>
-#include <spd.h>
-#include "southbridge/intel/i82801ex/early_smbus.c"
-#include "northbridge/intel/e7501/raminit.h"
-#include "northbridge/intel/e7501/debug.c"
-#include <superio/winbond/common/winbond.h>
-#include <superio/winbond/w83627hf/w83627hf.h>
-#include "cpu/x86/bist.h"
-
-#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
-
-// FIXME: There's another hard_reset() in reset.c. Why?
-static void hard_reset(void)
-{
- /* full reset */
- outb(0x0a, 0x0cf9);
- outb(0x0e, 0x0cf9);
-}
-
-static inline int spd_read_byte(unsigned device, unsigned address)
-{
- return smbus_read_byte(device, address);
-}
-
-#include "northbridge/intel/e7501/raminit.c"
-#include "northbridge/intel/e7501/reset_test.c"
-#include "lib/generic_sdram.c"
-
-#include <cpu/intel/romstage.h>
-void main(unsigned long bist)
-{
- static const struct mem_controller memctrl[] = {
- {
- .d0 = PCI_DEV(0, 0, 0),
- .d0f1 = PCI_DEV(0, 0, 1),
- .channel0 = { DIMM0, DIMM1, DIMM2, 0 },
- .channel1 = { DIMM4, DIMM5, DIMM6, 0 },
- },
- };
-
- if (bist == 0)
- enable_lapic();
-
- winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
- console_init();
-
- /* Halt if there was a built in self test failure */
- report_bist_failure(bist);
-
- if (bios_reset_detected())
- hard_reset();
-
- enable_smbus();
-#if 0
- dump_spd_registers(&memctrl[0]);
- dump_smbus_registers();
-#endif
-
- sdram_initialize(1, memctrl);
-
-#if 0
- dump_pci_devices();
-#endif
-
-#if 1
- dump_pci_device(PCI_DEV(0, 0, 0));
-#endif
-}
diff --git a/src/northbridge/intel/Kconfig b/src/northbridge/intel/Kconfig
index 9ff66d3..b3df67b 100644
--- a/src/northbridge/intel/Kconfig
+++ b/src/northbridge/intel/Kconfig
@@ -1,4 +1,3 @@
-source src/northbridge/intel/e7501/Kconfig
source src/northbridge/intel/e7505/Kconfig
source src/northbridge/intel/e7525/Kconfig
source src/northbridge/intel/i3100/Kconfig
diff --git a/src/northbridge/intel/Makefile.inc b/src/northbridge/intel/Makefile.inc
index 020caa8..2239675 100644
--- a/src/northbridge/intel/Makefile.inc
+++ b/src/northbridge/intel/Makefile.inc
@@ -1,4 +1,3 @@
-subdirs-$(CONFIG_NORTHBRIDGE_INTEL_E7501) += e7501
subdirs-$(CONFIG_NORTHBRIDGE_INTEL_E7505) += e7505
subdirs-$(CONFIG_NORTHBRIDGE_INTEL_E7525) += e7525
subdirs-$(CONFIG_NORTHBRIDGE_INTEL_I3100) += i3100
diff --git a/src/northbridge/intel/e7501/Kconfig b/src/northbridge/intel/e7501/Kconfig
deleted file mode 100644
index 88c0b45..0000000
--- a/src/northbridge/intel/e7501/Kconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-config NORTHBRIDGE_INTEL_E7501
- bool
- select HAVE_DEBUG_RAM_SETUP
- select PER_DEVICE_ACPI_TABLES
-
diff --git a/src/northbridge/intel/e7501/Makefile.inc b/src/northbridge/intel/e7501/Makefile.inc
deleted file mode 100644
index 23eada5..0000000
--- a/src/northbridge/intel/e7501/Makefile.inc
+++ /dev/null
@@ -1 +0,0 @@
-ramstage-y += northbridge.c
diff --git a/src/northbridge/intel/e7501/debug.c b/src/northbridge/intel/e7501/debug.c
deleted file mode 100644
index 07f1596..0000000
--- a/src/northbridge/intel/e7501/debug.c
+++ /dev/null
@@ -1,275 +0,0 @@
-/*
- * generic debug code, used by mainboard specific romstage.c
- *
- */
-#if 1
-static void print_debug_pci_dev(unsigned dev)
-{
- print_debug("PCI: ");
- print_debug_hex8((dev >> 16) & 0xff);
- print_debug_char(':');
- print_debug_hex8((dev >> 11) & 0x1f);
- print_debug_char('.');
- print_debug_hex8((dev >> 8) & 7);
-}
-
-static inline void print_pci_devices(void)
-{
- device_t dev;
- for(dev = PCI_DEV(0, 0, 0);
- dev <= PCI_DEV(0xff, 0x1f, 0x7);
- dev += PCI_DEV(0,0,1)) {
- uint32_t id;
- id = pci_read_config32(dev, PCI_VENDOR_ID);
- if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
- (((id >> 16) & 0xffff) == 0xffff) ||
- (((id >> 16) & 0xffff) == 0x0000)) {
- continue;
- }
- print_debug_pci_dev(dev);
- print_debug("\n");
- }
-}
-
-static void dump_pci_device(unsigned dev)
-{
- int i;
- print_debug_pci_dev(dev);
-
- for(i = 0; i < 256; i++) {
- unsigned char val;
- if ((i & 0x0f) == 0) {
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "\n%02x:",i);
-#else
- print_debug("\n");
- print_debug_hex8(i);
- print_debug_char(':');
-#endif
- }
- val = pci_read_config8(dev, i);
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, " %02x", val);
-#else
- print_debug_char(' ');
- print_debug_hex8(val);
-#endif
- }
- print_debug("\n");
-}
-
-static inline void dump_pci_devices(void)
-{
- device_t dev;
- for(dev = PCI_DEV(0, 0, 0);
- dev <= PCI_DEV(0xff, 0x1f, 0x7);
- dev += PCI_DEV(0,0,1)) {
- uint32_t id;
- id = pci_read_config32(dev, PCI_VENDOR_ID);
- if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
- (((id >> 16) & 0xffff) == 0xffff) ||
- (((id >> 16) & 0xffff) == 0x0000)) {
- continue;
- }
- dump_pci_device(dev);
- }
-}
-
-static inline void dump_pci_devices_on_bus(unsigned busn)
-{
- device_t dev;
- for(dev = PCI_DEV(busn, 0, 0);
- dev <= PCI_DEV(busn, 0x1f, 0x7);
- dev += PCI_DEV(0,0,1)) {
- uint32_t id;
- id = pci_read_config32(dev, PCI_VENDOR_ID);
- if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
- (((id >> 16) & 0xffff) == 0xffff) ||
- (((id >> 16) & 0xffff) == 0x0000)) {
- continue;
- }
- dump_pci_device(dev);
- }
-}
-
-static inline void dump_spd_registers(const struct mem_controller *ctrl)
-{
- int i;
- print_debug("\n");
- for(i = 0; i < 4; i++) {
- unsigned device;
- device = ctrl->channel0[i];
- if (device) {
- int j;
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "dimm: %02x.0: %02x", i, device);
-#else
- print_debug("dimm: ");
- print_debug_hex8(i);
- print_debug(".0: ");
- print_debug_hex8(device);
-#endif
- for(j = 0; j < 128; j++) {
- int status;
- unsigned char byte;
- if ((j & 0xf) == 0) {
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "\n%02x: ", j);
-#else
- print_debug("\n");
- print_debug_hex8(j);
- print_debug(": ");
-#endif
- }
- status = smbus_read_byte(device, j);
- if (status < 0) {
- break;
- }
- byte = status & 0xff;
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "%02x ", byte);
-#else
- print_debug_hex8(byte);
- print_debug_char(' ');
-#endif
- }
- print_debug("\n");
- }
- device = ctrl->channel1[i];
- if (device) {
- int j;
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "dimm: %02x.1: %02x", i, device);
-#else
- print_debug("dimm: ");
- print_debug_hex8(i);
- print_debug(".1: ");
- print_debug_hex8(device);
-#endif
- for(j = 0; j < 128; j++) {
- int status;
- unsigned char byte;
- if ((j & 0xf) == 0) {
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "\n%02x: ", j);
-#else
- print_debug("\n");
- print_debug_hex8(j);
- print_debug(": ");
-#endif
- }
- status = smbus_read_byte(device, j);
- if (status < 0) {
- break;
- }
- byte = status & 0xff;
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "%02x ", byte);
-#else
- print_debug_hex8(byte);
- print_debug_char(' ');
-#endif
- }
- print_debug("\n");
- }
- }
-}
-static inline void dump_smbus_registers(void)
-{
- unsigned device;
- print_debug("\n");
- for(device = 1; device < 0x80; device++) {
- int j;
- if( smbus_read_byte(device, 0) < 0 ) continue;
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "smbus: %02x", device);
-#else
- print_debug("smbus: ");
- print_debug_hex8(device);
-#endif
- for(j = 0; j < 256; j++) {
- int status;
- unsigned char byte;
- status = smbus_read_byte(device, j);
- if (status < 0) {
- break;
- }
- if ((j & 0xf) == 0) {
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "\n%02x: ",j);
-#else
- print_debug("\n");
- print_debug_hex8(j);
- print_debug(": ");
-#endif
- }
- byte = status & 0xff;
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "%02x ", byte);
-#else
- print_debug_hex8(byte);
- print_debug_char(' ');
-#endif
- }
- print_debug("\n");
- }
-}
-
-static inline void dump_io_resources(unsigned port)
-{
-
- int i;
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "%04x:\n", port);
-#else
- print_debug_hex16(port);
- print_debug(":\n");
-#endif
- for(i=0;i<256;i++) {
- uint8_t val;
- if ((i & 0x0f) == 0) {
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "%02x:", i);
-#else
- print_debug_hex8(i);
- print_debug_char(':');
-#endif
- }
- val = inb(port);
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, " %02x",val);
-#else
- print_debug_char(' ');
- print_debug_hex8(val);
-#endif
- if ((i & 0x0f) == 0x0f) {
- print_debug("\n");
- }
- port++;
- }
-}
-
-static inline void dump_mem(unsigned start, unsigned end)
-{
- unsigned i;
- print_debug("dump_mem:");
- for(i=start;i<end;i++) {
- if((i & 0xf)==0) {
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, "\n%08x:", i);
-#else
- print_debug("\n");
- print_debug_hex32(i);
- print_debug(":");
-#endif
- }
-#if !defined(__ROMCC__)
- printk(BIOS_DEBUG, " %02x", (unsigned char)*((unsigned char *)i));
-#else
- print_debug(" ");
- print_debug_hex8((unsigned char)*((unsigned char *)i));
-#endif
- }
- print_debug("\n");
- }
-#endif
diff --git a/src/northbridge/intel/e7501/e7501.h b/src/northbridge/intel/e7501/e7501.h
deleted file mode 100644
index 1e431b1..0000000
--- a/src/northbridge/intel/e7501/e7501.h
+++ /dev/null
@@ -1,79 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2005 Digital Design Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-/*
- * e7501.h: PCI configuration space for the Intel E7501 memory controller
- */
-
-/************ D0:F0 ************/
-// Register offsets
-#define MAYBE_SMRBASE 0x14 /* System Memory RCOMP Base Address Register, 32 bit? (if similar to 855PM) */
-#define MCHCFGNS 0x52 /* MCH (scrubber) configuration register, 16 bit */
-#define DRB_ROW_0 0x60 /* DRAM Row Boundary register, 8 bit */
-#define DRB_ROW_1 0x61
-#define DRB_ROW_2 0x62
-#define DRB_ROW_3 0x63
-#define DRB_ROW_4 0x64
-#define DRB_ROW_5 0x65
-#define DRB_ROW_6 0x66
-#define DRB_ROW_7 0x67
-
-#define DRA 0x70 /* DRAM Row Attributes registers, 4 x 8 bit */
-#define DRT 0x78 /* DRAM Timing register, 32 bit */
-#define DRC 0x7C /* DRAM Controller Mode register, 32 bit */
-#define MAYBE_DRDCTL 0x80 /* DRAM Read Timing Control register, 16 bit? (if similar to 855PM) */
-#define CKDIS 0x8C /* Clock disable register, 8 bit */
-#define TOLM 0xC4 /* Top of Low Memory register, 16 bit */
-#define REMAPBASE 0xC6 /* Remap Base Address register, 16 bit */
-#define REMAPLIMIT 0xC8 /* Remap Limit Address register, 16 bit */
-#define SKPD 0xDE /* Scratchpad register, 16 bit */
-#define MAYBE_MCHTST 0xF4 /* MCH Test Register, 32 bit? (if similar to 855PM) */
-
-// CAS# Latency bits in the DRAM Timing (DRT) register
-#define DRT_CAS_2_5 (0<<4)
-#define DRT_CAS_2_0 (1<<4)
-#define DRT_CAS_MASK (3<<4)
-
-// Mode Select (SMS) bits in the DRAM Controller Mode (DRC) register
-#define RAM_COMMAND_NOP (1<<4)
-#define RAM_COMMAND_PRECHARGE (2<<4)
-#define RAM_COMMAND_MRS (3<<4)
-#define RAM_COMMAND_EMRS (4<<4)
-#define RAM_COMMAND_CBR (6<<4)
-#define RAM_COMMAND_NORMAL (7<<4)
-
-
-// RCOMP Memory Map offsets
-// Conjecture based on apparent similarity between E7501 and 855PM
-// Intel doc. 252613-003 describes these for 855PM
-
-#define MAYBE_SMRCTL 0x20 /* System Memory RCOMP Control Register? */
-#define MAYBE_DQCMDSTR 0x30 /* Strength control for DQ and CMD signal groups? */
-#define MAYBE_CKESTR 0x31 /* Strength control for CKE signal group? */
-#define MAYBE_CSBSTR 0x32 /* Strength control for CS# signal group? */
-#define MAYBE_CKSTR 0x33 /* Strength control for CK signal group? */
-#define MAYBE_RCVENSTR 0x34 /* Strength control for RCVEnOut# signal group? */
-
-/************ D0:F1 ************/
-// Register offsets
-#define FERR_GLOBAL 0x40 /* First global error register, 32 bits */
-#define NERR_GLOBAL 0x44 /* Next global error register, 32 bits */
-#define DRAM_FERR 0x80 /* DRAM first error register, 8 bits */
-#define DRAM_NERR 0x82 /* DRAM next error register, 8 bits */
diff --git a/src/northbridge/intel/e7501/northbridge.c b/src/northbridge/intel/e7501/northbridge.c
deleted file mode 100644
index 64bf840..0000000
--- a/src/northbridge/intel/e7501/northbridge.c
+++ /dev/null
@@ -1,140 +0,0 @@
-#include <console/console.h>
-#include <arch/io.h>
-#include <stdint.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <arch/acpi.h>
-#include <cpu/cpu.h>
-#include <stdlib.h>
-#include <string.h>
-#include <cbmem.h>
-
-#if IS_ENABLED(CONFIG_HAVE_ACPI_TABLES)
-
-unsigned long acpi_fill_mcfg(unsigned long current)
-{
- /* Just a dummy */
- return current;
-}
-
-#endif
-
-
-static void pci_domain_set_resources(device_t dev)
-{
- device_t mc_dev;
- uint32_t pci_tolm;
-
- pci_tolm = find_pci_tolm(dev->link_list);
- mc_dev = dev->link_list->children;
- if (mc_dev) {
- /* Figure out which areas are/should be occupied by RAM.
- * This is all computed in kilobytes and converted to/from
- * the memory controller right at the edges.
- * Having different variables in different units is
- * too confusing to get right. Kilobytes are good up to
- * 4 Terabytes of RAM...
- */
- uint16_t tolm_r, remapbase_r, remaplimit_r;
- unsigned long tomk, tolmk;
- unsigned long remapbasek, remaplimitk;
- int idx;
-
- /* Get the value of the highest DRB. This tells the end of
- * the physical memory. The units are ticks of 64MB
- * i.e. 1 means 64MB.
- */
- tomk = ((unsigned long)pci_read_config8(mc_dev, 0x67)) << 16;
- /* Compute the top of Low memory */
- tolmk = pci_tolm >> 10;
- if (tolmk >= tomk) {
- /* The PCI hole does not overlap memory
- * we won't use the remap window.
- */
- tolmk = tomk;
- remapbasek = 0x3ff << 16;
- remaplimitk = 0 << 16;
- }
- else {
- /* The PCI memory hole overlaps memory
- * setup the remap window.
- */
- /* Find the bottom of the remap window
- * is it above 4G?
- */
- remapbasek = 4*1024*1024;
- if (tomk > remapbasek) {
- remapbasek = tomk;
- }
- /* Find the limit of the remap window */
- remaplimitk = (remapbasek + (4*1024*1024 - tolmk) - (1 << 16));
- }
- /* Write the ram configuration registers,
- * preserving the reserved bits.
- */
- tolm_r = pci_read_config16(mc_dev, 0xc4);
- tolm_r = ((tolmk >> 17) << 11) | (tolm_r & 0x7ff);
- pci_write_config16(mc_dev, 0xc4, tolm_r);
-
- remapbase_r = pci_read_config16(mc_dev, 0xc6);
- remapbase_r = (remapbasek >> 16) | (remapbase_r & 0xfc00);
- pci_write_config16(mc_dev, 0xc6, remapbase_r);
-
- remaplimit_r = pci_read_config16(mc_dev, 0xc8);
- remaplimit_r = (remaplimitk >> 16) | (remaplimit_r & 0xfc00);
- pci_write_config16(mc_dev, 0xc8, remaplimit_r);
-
- /* Report the memory regions */
- idx = 10;
- ram_resource(dev, idx++, 0, 640);
- ram_resource(dev, idx++, 768, tolmk - 768);
- if (tomk > 4*1024*1024) {
- ram_resource(dev, idx++, 4096*1024, tomk - 4*1024*1024);
- }
- if (remaplimitk >= remapbasek) {
- ram_resource(dev, idx++, remapbasek,
- (remaplimitk + 64*1024) - remapbasek);
- }
-
- set_top_of_ram(tolmk * 1024);
- }
- assign_resources(dev->link_list);
-}
-
-static struct device_operations pci_domain_ops = {
- .read_resources = pci_domain_read_resources,
- .set_resources = pci_domain_set_resources,
- .enable_resources = NULL,
- .init = NULL,
- .scan_bus = pci_domain_scan_bus,
- .ops_pci_bus = pci_bus_default_ops,
-};
-
-static void cpu_bus_init(device_t dev)
-{
- initialize_cpus(dev->link_list);
-}
-
-static struct device_operations cpu_bus_ops = {
- .read_resources = DEVICE_NOOP,
- .set_resources = DEVICE_NOOP,
- .enable_resources = DEVICE_NOOP,
- .init = cpu_bus_init,
- .scan_bus = 0,
-};
-
-static void enable_dev(struct device *dev)
-{
- /* Set the operations if it is a special bus type */
- if (dev->path.type == DEVICE_PATH_DOMAIN) {
- dev->ops = &pci_domain_ops;
- }
- else if (dev->path.type == DEVICE_PATH_CPU_CLUSTER) {
- dev->ops = &cpu_bus_ops;
- }
-}
-
-struct chip_operations northbridge_intel_e7501_ops = {
- CHIP_NAME("Intel E7501 Northbridge")
- .enable_dev = enable_dev,
-};
diff --git a/src/northbridge/intel/e7501/raminit.c b/src/northbridge/intel/e7501/raminit.c
deleted file mode 100644
index 2247a25..0000000
--- a/src/northbridge/intel/e7501/raminit.c
+++ /dev/null
@@ -1,2007 +0,0 @@
-/* This was originally for the e7500, modified for e7501
- * The primary differences are that 7501 apparently can
- * support single channel RAM (i haven't tested),
- * CAS1.5 is no longer supported, The ECC scrubber
- * now supports a mode to zero RAM and init ECC in one step
- * and the undocumented registers at 0x80 require new
- * (undocumented) values determined by guesswork and
- * comparison w/ OEM BIOS values.
- * Steven James 02/06/2003
- */
-
-/* converted to C 6/2004 yhlu */
-
-#include <assert.h>
-#include <spd.h>
-#include <sdram_mode.h>
-#include <stdlib.h>
-#include "e7501.h"
-
-/*-----------------------------------------------------------------------------
-Definitions:
------------------------------------------------------------------------------*/
-
-// Uncomment this to enable run-time checking of DIMM parameters
-// for dual-channel operation
-// Unfortunately the code seems to chew up several K of space.
-//#define VALIDATE_DIMM_COMPATIBILITY
-
-#if CONFIG_DEBUG_RAM_SETUP
-#define RAM_DEBUG_MESSAGE(x) print_debug(x)
-#define RAM_DEBUG_HEX32(x) print_debug_hex32(x)
-#define RAM_DEBUG_HEX8(x) print_debug_hex8(x)
-#define DUMPNORTH() dump_pci_device(PCI_DEV(0, 0, 0))
-#else
-#define RAM_DEBUG_MESSAGE(x)
-#define RAM_DEBUG_HEX32(x)
-#define RAM_DEBUG_HEX8(x)
-#define DUMPNORTH()
-#endif
-
-#define E7501_SDRAM_MODE (SDRAM_BURST_INTERLEAVED | SDRAM_BURST_4)
-#define SPD_ERROR "Error reading SPD info\n"
-
-// NOTE: This used to be 0x100000.
-// That doesn't work on systems where A20M# is asserted, because
-// attempts to access 0x1000NN end up accessing 0x0000NN.
-#define RCOMP_MMIO 0x200000
-
-struct dimm_size {
- unsigned long side1;
- unsigned long side2;
-};
-
-static const uint32_t refresh_frequency[] = {
- /* Relative frequency (array value) of each E7501 Refresh Mode Select
- * (RMS) value (array index)
- * 0 == least frequent refresh (longest interval between refreshes)
- * [0] disabled -> 0
- * [1] 15.6 usec -> 2
- * [2] 7.8 usec -> 3
- * [3] 64 usec -> 1
- * [4] reserved -> 0
- * [5] reserved -> 0
- * [6] reserved -> 0
- * [7] 64 clocks -> 4
- */
- 0, 2, 3, 1, 0, 0, 0, 4
-};
-
-static const uint32_t refresh_rate_map[] = {
- /* Map the JEDEC spd refresh rates (array index) to E7501 Refresh Mode
- * Select values (array value)
- * These are all the rates defined by JESD21-C Appendix D, Rev. 1.0
- * The E7501 supports only 15.6 us (1), 7.8 us (2), 64 us (3), and
- * 64 clock (481 ns) (7) refresh.
- * [0] == 15.625 us -> 15.6 us
- * [1] == 3.9 us -> 481 ns
- * [2] == 7.8 us -> 7.8 us
- * [3] == 31.3 us -> 15.6 us
- * [4] == 62.5 us -> 15.6 us
- * [5] == 125 us -> 64 us
- */
- 1, 7, 2, 1, 1, 3
-};
-
-#define MAX_SPD_REFRESH_RATE ((sizeof(refresh_rate_map) / sizeof(uint32_t)) - 1)
-
-// SPD parameters that must match for dual-channel operation
-static const uint8_t dual_channel_parameters[] = {
- SPD_MEMORY_TYPE,
- SPD_MODULE_VOLTAGE,
- SPD_NUM_COLUMNS,
- SPD_NUM_ROWS,
- SPD_NUM_DIMM_BANKS,
- SPD_PRIMARY_SDRAM_WIDTH,
- SPD_NUM_BANKS_PER_SDRAM
-};
-
- /*
- * Table: constant_register_values
- */
-static const long constant_register_values[] = {
- /* SVID - Subsystem Vendor Identification Register
- * 0x2c - 0x2d
- * [15:00] Subsytem Vendor ID (Indicates system board vendor)
- */
- /* SID - Subsystem Identification Register
- * 0x2e - 0x2f
- * [15:00] Subsystem ID
- */
- // Not everyone wants to be Super Micro Computer, Inc.
- // The mainboard should set this if desired.
- // 0x2c, 0, (0x15d9 << 0) | (0x3580 << 16),
-
- /* Undocumented
- * (DRAM Read Timing Control, if similar to 855PM?)
- * 0x80 - 0x81
- * This register has something to do with CAS latencies,
- * possibily this is the real chipset control.
- * At 0x00 CAS latency 1.5 works.
- * At 0x06 CAS latency 2.5 works.
- * At 0x01 CAS latency 2.0 works.
- */
- /* This is still undocumented in e7501, but with different values
- * CAS 2.0 values taken from Intel BIOS settings, others are a guess
- * and may be terribly wrong. Old values preserved as comments until I
- * figure this out for sure.
- * e7501 docs claim that CAS1.5 is unsupported, so it may or may not
- * work at all.
- * Steven James 02/06/2003
- */
- /* NOTE: values now configured in configure_e7501_cas_latency() based
- * on SPD info and total number of DIMMs (per Intel)
- */
-
- /* FDHC - Fixed DRAM Hole Control
- * 0x58
- * [7:7] Hole_Enable
- * 0 == No memory Hole
- * 1 == Memory Hole from 15MB to 16MB
- * [6:0] Reserved
- *
- * PAM - Programmable Attribute Map
- * 0x59 [1:0] Reserved
- * 0x59 [5:4] 0xF0000 - 0xFFFFF
- * 0x5A [1:0] 0xC0000 - 0xC3FFF
- * 0x5A [5:4] 0xC4000 - 0xC7FFF
- * 0x5B [1:0] 0xC8000 - 0xCBFFF
- * 0x5B [5:4] 0xCC000 - 0xCFFFF
- * 0x5C [1:0] 0xD0000 - 0xD3FFF
- * 0x5C [5:4] 0xD4000 - 0xD7FFF
- * 0x5D [1:0] 0xD8000 - 0xDBFFF
- * 0x5D [5:4] 0xDC000 - 0xDFFFF
- * 0x5E [1:0] 0xE0000 - 0xE3FFF
- * 0x5E [5:4] 0xE4000 - 0xE7FFF
- * 0x5F [1:0] 0xE8000 - 0xEBFFF
- * 0x5F [5:4] 0xEC000 - 0xEFFFF
- * 00 == DRAM Disabled (All Access go to memory mapped I/O space)
- * 01 == Read Only (Reads to DRAM, Writes to memory mapped I/O space)
- * 10 == Write Only (Writes to DRAM, Reads to memory mapped I/O space)
- * 11 == Normal (All Access go to DRAM)
- */
-
- // Map all legacy ranges to DRAM
- 0x58, 0xcccccf7f, (0x00 << 0) | (0x30 << 8) | (0x33 << 16) | (0x33 << 24),
- 0x5C, 0xcccccccc, (0x33 << 0) | (0x33 << 8) | (0x33 << 16) | (0x33 << 24),
-
- /* DRB - DRAM Row Boundary Registers
- * 0x60 - 0x6F
- * An array of 8 byte registers, which hold the ending
- * memory address assigned to each pair of DIMMS, in 64MB
- * granularity.
- */
- // Conservatively say each row has 64MB of ram, we will fix this up later
- // NOTE: These defaults allow us to prime all of the DIMMs on the board
- // without jumping through 36-bit adddressing hoops, even if the
- // total memory is > 4 GB. Changing these values may break do_ram_command()!
- 0x60, 0x00000000, (0x01 << 0) | (0x02 << 8) | (0x03 << 16) | (0x04 << 24),
- 0x64, 0x00000000, (0x05 << 0) | (0x06 << 8) | (0x07 << 16) | (0x08 << 24),
-
- /* DRA - DRAM Row Attribute Register
- * 0x70 Row 0,1
- * 0x71 Row 2,3
- * 0x72 Row 4,5
- * 0x73 Row 6,7
- * [7:7] Device width for Odd numbered rows
- * 0 == 8 bits wide x8
- * 1 == 4 bits wide x4
- * [6:4] Row Attributes for Odd numbered rows
- * 010 == 8KB (for dual-channel)
- * 011 == 16KB (for dual-channel)
- * 100 == 32KB (for dual-channel)
- * 101 == 64KB (for dual-channel)
- * Others == Reserved
- * [3:3] Device width for Even numbered rows
- * 0 == 8 bits wide x8
- * 1 == 4 bits wide x4
- * [2:0] Row Attributes for Even numbered rows
- * 010 == 8KB (for dual-channel)
- * 011 == 16KB (for dual-channel)
- * 100 == 32KB (for dual-channel)
- * 101 == 64KB (This page size appears broken)
- * Others == Reserved
- */
- // NOTE: overridden by configure_e7501_row_attributes(), later
- 0x70, 0x00000000, 0,
-
- /* DRT - DRAM Timing Register
- * 0x78
- * [31:30] Reserved
- * [29:29] Back to Back Write-Read Turn Around
- * 0 == 3 clocks between WR-RD commands
- * 1 == 2 clocks between WR-RD commands
- * [28:28] Back to Back Read-Write Turn Around
- * 0 == 5 clocks between RD-WR commands
- * 1 == 4 clocks between RD-WR commands
- * [27:27] Back to Back Read Turn Around
- * 0 == 4 clocks between RD commands
- * 1 == 3 clocks between RD commands
- * [26:24] Read Delay (tRD)
- * 000 == 7 clocks
- * 001 == 6 clocks
- * 010 == 5 clocks
- * Others == Reserved
- * [23:19] Reserved
- * [18:16] DRAM idle timer
- * 000 == infinite
- * 011 == 16 dram clocks
- * 001 == 0 clocks
- * [15:11] Reserved
- * [10:09] Active to Precharge (tRAS)
- * 00 == 7 clocks
- * 01 == 6 clocks
- * 10 == 5 clocks
- * 11 == Reserved
- * [08:06] Reserved
- * [05:04] Cas Latency (tCL)
- * 00 == 2.5 Clocks
- * 01 == 2.0 Clocks
- * 10 == Reserved (was 1.5 Clocks for E7500)
- * 11 == Reserved
- * [03:03] Write Ras# to Cas# Delay (tRCD)
- * 0 == 3 DRAM Clocks
- * 1 == 2 DRAM Clocks
- * [02:01] Read RAS# to CAS# Delay (tRCD)
- * 00 == reserved
- * 01 == reserved
- * 10 == 3 DRAM Clocks
- * 11 == 2 DRAM Clocks
- * [00:00] DRAM RAS# to Precharge (tRP)
- * 0 == 3 DRAM Clocks
- * 1 == 2 DRAM Clocks
- */
-
- // Some earlier settings:
- /* Most aggressive settings possible */
-// 0x78, 0xc0fff8c4, (1<<29)|(1<<28)|(1<<27)|(2<<24)|(2<<9)|CAS_LATENCY|(1<<3)|(1<<1)|(1<<0),
-// 0x78, 0xc0f8f8c0, (1<<29)|(1<<28)|(1<<27)|(1<<24)|(1<<16)|(2<<9)|CAS_LATENCY|(1<<3)|(3<<1)|(1<<0),
-// 0x78, 0xc0f8f9c0, (1<<29)|(1<<28)|(1<<27)|(1<<24)|(1<<16)|(2<<9)|CAS_LATENCY|(1<<3)|(3<<1)|(1<<0),
-
- // The only things we need to set here are DRAM idle timer, Back-to-Back Read Turnaround, and
- // Back-to-Back Write-Read Turnaround. All others are configured based on SPD.
- 0x78, 0xD7F8FFFF, (1 << 29) | (1 << 27) | (1 << 16),
-
- /* FIXME why was I attempting to set a reserved bit? */
- /* 0x0100040f */
-
- /* DRC - DRAM Contoller Mode Register
- * 0x7c
- * [31:30] Reserved
- * [29:29] Initialization Complete
- * 0 == Not Complete
- * 1 == Complete
- * [28:23] Reserved
- * [22:22] Channels
- * 0 == Single channel
- * 1 == Dual Channel
- * [21:20] DRAM Data Integrity Mode
- * 00 == Disabled, no ECC
- * 01 == Reserved
- * 10 == Error checking, using chip-kill, with correction
- * 11 == Reserved
- * [19:18] DRB Granularity (Read-Only)
- * 00 == 32 MB quantities (single channel mode)
- * 01 == 64 MB quantities (dual-channel mode)
- * 10 == Reserved
- * 11 == Reserved
- * [17:17] (Intel Undocumented) should always be set to 1 (SJM: comment inconsistent with current setting, below)
- * [16:16] Command Per Clock - Address/Control Assertion Rule (CPC)
- * 0 == 2n Rule
- * 1 == 1n rule
- * [15:11] Reserved
- * [10:08] Refresh mode select
- * 000 == Refresh disabled
- * 001 == Refresh interval 15.6 usec
- * 010 == Refresh interval 7.8 usec
- * 011 == Refresh interval 64 usec
- * 111 == Refresh every 64 clocks (fast refresh)
- * [07:07] Reserved
- * [06:04] Mode Select (SMS)
- * 000 == Reserved (was Self Refresh Mode in E7500)
- * 001 == NOP Command
- * 010 == All Banks Precharge
- * 011 == Mode Register Set
- * 100 == Extended Mode Register Set
- * 101 == Reserved
- * 110 == CBR Refresh
- * 111 == Normal Operation
- * [03:00] Reserved
- */
-// .long 0x7c, 0xffcefcff, (1<<22)|(2 << 20)|(1 << 16)| (0 << 8),
-// .long 0x7c, 0xff8cfcff, (1<<22)|(2 << 20)|(1 << 17)|(1 << 16)| (0 << 8),
-// .long 0x7c, 0xff80fcff, (1<<22)|(2 << 20)|(1 << 18)|(1 << 17)|(1 << 16)| (0 << 8),
-
- // Default to dual-channel mode, ECC, 1-clock address/cmd hold
- // NOTE: configure_e7501_dram_controller_mode() configures further
- 0x7c, 0xff8ef8ff, (1 << 22) | (2 << 20) | (1 << 16) | (0 << 8),
-
- /* Another Intel undocumented register
- * 0x88 - 0x8B
- * [31:31] Purpose unknown
- * [26:26] Master DLL Reset?
- * 0 == Normal operation?
- * 1 == Reset?
- * [07:07] Periodic memory recalibration?
- * 0 == Disabled?
- * 1 == Enabled?
- * [04:04] Receive FIFO RE-Sync?
- * 0 == Normal operation?
- * 1 == Reset?
- */
- // NOTE: Some factory BIOSs don't do this.
- // Doesn't seem to matter either way.
- 0x88, 0xffffff00, 0x80,
-
- /* CLOCK_DIS - CK/CK# Disable Register
- * 0x8C
- * [7:7] DDR Frequency
- * 0 == 100 MHz (200 MHz data rate)
- * 1 == 133 MHz (266 MHz data rate)
- * [6:4] Reserved
- * [3:3] CK3
- * 0 == Enable
- * 1 == Disable
- * [2:2] CK2
- * 0 == Enable
- * 1 == Disable
- * [1:1] CK1
- * 0 == Enable
- * 1 == Disable
- * [0:0] CK0
- * 0 == Enable
- * 1 == Disable
- */
- // NOTE: Disable all clocks initially; turn ones we need back on
- // in enable_e7501_clocks()
- 0x8C, 0xfffffff0, 0xf,
-
- /* TOLM - Top of Low Memory Register
- * 0xC4 - 0xC5
- * [15:11] Top of low memory (TOLM)
- * The address below 4GB that should be treated as RAM,
- * on a 128MB granularity.
- * [10:00] Reserved
- */
- /* REMAPBASE - Remap Base Address Regsiter
- * 0xC6 - 0xC7
- * [15:10] Reserved
- * [09:00] Remap Base Address [35:26] 64M aligned
- * Bits [25:0] are assumed to be 0.
- */
-
- // NOTE: TOLM overridden by configure_e7501_ram_addresses()
- 0xc4, 0xfc0007ff, (0x2000 << 0) | (0x3ff << 16),
-
- /* REMAPLIMIT - Remap Limit Address Register
- * 0xC8 - 0xC9
- * [15:10] Reserved
- * [09:00] Remap Limit Address [35:26] 64M aligned
- * When remaplimit < remapbase the remap window is disabled.
- */
- 0xc8, 0xfffffc00, 0,
-
- /* DVNP - Device Not Present Register
- * 0xE0 - 0xE1
- * [15:05] Reserved
- * [04:04] Device 4 Function 1 Present
- * 0 == Present
- * 1 == Absent
- * [03:03] Device 3 Function 1 Present
- * 0 == Present
- * 1 == Absent
- * [02:02] Device 2 Function 1 Present
- * 0 == Present
- * 1 == Absent
- * [01:01] Reserved
- * [00:00] Device 0 Function 1 Present
- * 0 == Present
- * 1 == Absent
- */
-
- // Enable D0:D1, disable D2:F1, D3:F1, D4:F1
- 0xe0, 0xffffffe2, (1 << 4) | (1 << 3) | (1 << 2) | (0 << 0),
-
- // Undocumented
- 0xd8, 0xffff9fff, 0x00000000,
-
- // Undocumented - this is pure conjecture based on similarity to 855PM
- /* MCHTST - MCH Test Register
- * 0xF4 - 0xF7
- * [31:31] Purpose unknown
- * [30:30] Purpose unknown
- * [29:23] Unknown - not used?
- * [22:22] System Memory MMR Enable
- * 0 == Disable: mem space and BAR at 0x14 are not accessible
- * 1 == Enable: mem space and BAR at 0x14 are accessible
- * [21:20] Purpose unknown
- * [19:02] Unknown - not used?
- * [01:01] D6EN (Device #6 enable)
- * 0 == Disable
- * 1 == Enable
- * [00:00] Unknown - not used?
- */
-
- 0xf4, 0x3f8ffffd, 0x40300002,
-
-#ifdef SUSPICIOUS_LOOKING_CODE
- // SJM: Undocumented.
- // This will access D2:F0:0x50, is this correct??
- 0x1050, 0xffffffcf, 0x00000030,
-#endif
-};
-
- /* DDR RECOMP tables */
-
-// Slew table for 1x drive?
-static const uint32_t maybe_1x_slew_table[] = {
- 0x44332211, 0xc9776655, 0xffffffff, 0xffffffff,
- 0x22111111, 0x55444332, 0xfffca876, 0xffffffff,
-};
-
-// Slew table for 2x drive?
-static const uint32_t maybe_2x_slew_table[] = {
- 0x00000000, 0x76543210, 0xffffeca8, 0xffffffff,
- 0x21000000, 0xa8765432, 0xffffffec, 0xffffffff,
-};
-
-// Pull Up / Pull Down offset table, if analogous to IXP2800?
-static const uint32_t maybe_pull_updown_offset_table[] = {
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- 0x88888888, 0x88888888, 0x88888888, 0x88888888,
-};
-
-/*-----------------------------------------------------------------------------
-Delay functions:
------------------------------------------------------------------------------*/
-
-#define SLOW_DOWN_IO inb(0x80)
-//#define SLOW_DOWN_IO udelay(40);
-
- /* Estimate that SLOW_DOWN_IO takes about 50&76us */
- /* delay for 200us */
-
-#if 1
-static void do_delay(void)
-{
- int i;
- for (i = 0; i < 16; i++) {
- SLOW_DOWN_IO;
- }
-}
-
-#define DO_DELAY do_delay()
-#else
-#define DO_DELAY \
- udelay(200)
-#endif
-
-#define EXTRA_DELAY DO_DELAY
-
-static void die_on_spd_error(int spd_return_value)
-{
- if (spd_return_value < 0)
- die("Error reading SPD info\n");
-}
-
-/*-----------------------------------------------------------------------------
-Serial presence detect (SPD) functions:
------------------------------------------------------------------------------*/
-
-/**
- * Calculate the page size for each physical bank of the DIMM:
- * log2(page size) = (# columns) + log2(data width)
- *
- * NOTE: Page size is the total number of data bits in a row.
- *
- * @param dimm_socket_address SMBus address of DIMM socket to interrogate.
- * @return log2(page size) for each side of the DIMM.
- */
-static struct dimm_size sdram_spd_get_page_size(uint16_t dimm_socket_address)
-{
- uint16_t module_data_width;
- int value;
- struct dimm_size pgsz;
-
- pgsz.side1 = 0;
- pgsz.side2 = 0;
-
- // Side 1
- value = spd_read_byte(dimm_socket_address, SPD_NUM_COLUMNS);
- if (value < 0)
- goto hw_err;
- pgsz.side1 = value & 0xf; // # columns in bank 1
-
- /* Get the module data width and convert it to a power of two */
- value =
- spd_read_byte(dimm_socket_address, SPD_MODULE_DATA_WIDTH_MSB);
- if (value < 0)
- goto hw_err;
- module_data_width = (value & 0xff) << 8;
-
- value =
- spd_read_byte(dimm_socket_address, SPD_MODULE_DATA_WIDTH_LSB);
- if (value < 0)
- goto hw_err;
- module_data_width |= (value & 0xff);
-
- pgsz.side1 += log2(module_data_width);
-
- /* side two */
- value = spd_read_byte(dimm_socket_address, SPD_NUM_DIMM_BANKS);
- if (value < 0)
- goto hw_err;
- if (value > 2)
- die("Bad SPD value\n");
- if (value == 2) {
-
- pgsz.side2 = pgsz.side1; // Assume symmetric banks until we know differently
- value =
- spd_read_byte(dimm_socket_address, SPD_NUM_COLUMNS);
- if (value < 0)
- goto hw_err;
- if ((value & 0xf0) != 0) {
- // Asymmetric banks
- pgsz.side2 -= value & 0xf; /* Subtract out columns on side 1 */
- pgsz.side2 += (value >> 4) & 0xf; /* Add in columns on side 2 */
- }
- }
-
- return pgsz;
-
- hw_err:
- die(SPD_ERROR);
- return pgsz; // Never reached
-}
-
-/**
- * Read the width in bits of each DIMM side's DRAMs via SPD (i.e. 4, 8, 16).
- *
- * @param dimm_socket_address SMBus address of DIMM socket to interrogate.
- * @return Width in bits of each DIMM side's DRAMs.
- */
-static struct dimm_size sdram_spd_get_width(uint16_t dimm_socket_address)
-{
- int value;
- struct dimm_size width;
-
- width.side1 = 0;
- width.side2 = 0;
-
- value =
- spd_read_byte(dimm_socket_address, SPD_PRIMARY_SDRAM_WIDTH);
- die_on_spd_error(value);
-
- width.side1 = value & 0x7f; // Mask off bank 2 flag
-
- if (value & 0x80) {
- width.side2 = width.side1 << 1; // Bank 2 exists and is double-width
- } else {
- // If bank 2 exists, it's the same width as bank 1
- value =
- spd_read_byte(dimm_socket_address, SPD_NUM_DIMM_BANKS);
- die_on_spd_error(value);
-
-#ifdef ROMCC_IF_BUG_FIXED
- if (value == 2)
- width.side2 = width.side1;
-#else
- switch (value) {
- case 2:
- width.side2 = width.side1;
- break;
-
- default:
- break;
- }
-#endif
- }
-
- return width;
-}
-
-/**
- * Calculate the log base 2 size in bits of both DIMM sides.
- *
- * log2(# bits) = (# columns) + log2(data width) +
- * (# rows) + log2(banks per SDRAM)
- *
- * Note that it might be easier to use SPD byte 31 here, it has the DIMM size
- * as a multiple of 4MB. The way we do it now we can size both sides of an
- * asymmetric DIMM.
- *
- * @param dimm_socket_address SMBus address of DIMM socket to interrogate.
- * @return log2(number of bits) for each side of the DIMM.
- */
-static struct dimm_size spd_get_dimm_size(unsigned dimm_socket_address)
-{
- int value;
-
- // Start with log2(page size)
- struct dimm_size sz = sdram_spd_get_page_size(dimm_socket_address);
-
- if (sz.side1 > 0) {
-
- value = spd_read_byte(dimm_socket_address, SPD_NUM_ROWS);
- die_on_spd_error(value);
-
- sz.side1 += value & 0xf;
-
- if (sz.side2 > 0) {
-
- // Double-sided DIMM
- if (value & 0xF0)
- sz.side2 += value >> 4; // Asymmetric
- else
- sz.side2 += value; // Symmetric
- }
-
- value =
- spd_read_byte(dimm_socket_address,
- SPD_NUM_BANKS_PER_SDRAM);
- die_on_spd_error(value);
-
- value = log2(value);
- sz.side1 += value;
- if (sz.side2 > 0)
- sz.side2 += value;
- }
-
- return sz;
-}
-
-#ifdef VALIDATE_DIMM_COMPATIBILITY
-
-/**
- * Determine whether two DIMMs have the same value for an SPD parameter.
- *
- * @param spd_byte_number The SPD byte number to compare in both DIMMs.
- * @param dimm0_address SMBus address of the 1st DIMM socket to interrogate.
- * @param dimm1_address SMBus address of the 2nd DIMM socket to interrogate.
- * @return 1 if both DIMM sockets report the same value for the specified
- * SPD parameter, 0 if the values differed or an error occurred.
- */
-static uint8_t are_spd_values_equal(uint8_t spd_byte_number,
- uint16_t dimm0_address,
- uint16_t dimm1_address)
-{
- uint8_t bEqual = 0;
- int dimm0_value = spd_read_byte(dimm0_address, spd_byte_number);
- int dimm1_value = spd_read_byte(dimm1_address, spd_byte_number);
-
- if ((dimm0_value >= 0) && (dimm1_value >= 0)
- && (dimm0_value == dimm1_value))
- bEqual = 1;
-
- return bEqual;
-}
-#endif
-
-/**
- * Scan for compatible DIMMs.
- *
- * The code in this module only supports dual-channel operation, so we test
- * that compatible DIMMs are paired.
- *
- * @param ctrl PCI addresses of memory controller functions, and SMBus
- * addresses of DIMM slots on the mainboard.
- * @return A bitmask indicating which of the possible sockets for each channel
- * was found to contain a compatible DIMM.
- * Bit 0 corresponds to the closest socket for channel 0
- * Bit 1 to the next socket for channel 0
- * ...
- * Bit MAX_DIMM_SOCKETS_PER_CHANNEL-1 to the last socket for channel 0
- * Bit MAX_DIMM_SOCKETS_PER_CHANNEL is the closest socket for channel 1
- * ...
- * Bit 2*MAX_DIMM_SOCKETS_PER_CHANNEL-1 is the last socket for channel 1
- */
-static uint8_t spd_get_supported_dimms(const struct mem_controller *ctrl)
-{
- int i;
- uint8_t dimm_mask = 0;
-
- // Have to increase size of dimm_mask if this assertion is violated
- ASSERT(MAX_DIMM_SOCKETS_PER_CHANNEL <= 4);
-
- // Find DIMMs we can support on channel 0.
- // Then see if the corresponding channel 1 DIMM has the same parameters,
- // since we only support dual-channel.
-
- for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) {
-
- uint16_t channel0_dimm = ctrl->channel0[i];
- uint16_t channel1_dimm = ctrl->channel1[i];
- uint8_t bDualChannel = 1;
-#ifdef VALIDATE_DIMM_COMPATIBILITY
- struct dimm_size page_size;
- struct dimm_size sdram_width;
-#endif
- int spd_value;
-
- if (channel0_dimm == 0)
- continue; // No such socket on this mainboard
-
- if (spd_read_byte(channel0_dimm, SPD_MEMORY_TYPE) !=
- SPD_MEMORY_TYPE_SDRAM_DDR)
- continue;
-
-#ifdef VALIDATE_DIMM_COMPATIBILITY
- if (spd_read_byte(channel0_dimm, SPD_MODULE_VOLTAGE) !=
- SPD_VOLTAGE_SSTL2)
- continue; // Unsupported voltage
-
- // E7501 does not support unregistered DIMMs
- spd_value =
- spd_read_byte(channel0_dimm, SPD_MODULE_ATTRIBUTES);
- if (!(spd_value & MODULE_REGISTERED) || (spd_value < 0))
- continue;
-
- // Must support burst = 4 for dual-channel operation on E7501
- // NOTE: for single-channel, burst = 8 is required
- spd_value =
- spd_read_byte(channel0_dimm,
- SPD_SUPPORTED_BURST_LENGTHS);
- if (!(spd_value & SPD_BURST_LENGTH_4) || (spd_value < 0))
- continue;
-
- page_size = sdram_spd_get_page_size(channel0_dimm);
- sdram_width = sdram_spd_get_width(channel0_dimm);
-
- // Validate DIMM page size
- // The E7501 only supports page sizes of 4, 8, 16, or 32 KB per channel
- // NOTE: 4 KB = 32 Kb = 2^15
- // 32 KB = 262 Kb = 2^18
-
- if ((page_size.side1 < 15) || (page_size.side1 > 18))
- continue;
-
- // If DIMM is double-sided, verify side2 page size
- if (page_size.side2 != 0) {
- if ((page_size.side2 < 15)
- || (page_size.side2 > 18))
- continue;
- }
- // Validate SDRAM width
- // The E7501 only supports x4 and x8 devices
-
- if ((sdram_width.side1 != 4) && (sdram_width.side1 != 8))
- continue;
-
- // If DIMM is double-sided, verify side2 width
- if (sdram_width.side2 != 0) {
- if ((sdram_width.side2 != 4)
- && (sdram_width.side2 != 8))
- continue;
- }
-#endif
- // Channel 0 DIMM looks compatible.
- // Now see if it is paired with the proper DIMM on channel 1.
-
- ASSERT(channel1_dimm != 0); // No such socket on this mainboard??
-
- // NOTE: unpopulated DIMMs cause read to fail
- spd_value =
- spd_read_byte(channel1_dimm, SPD_MODULE_ATTRIBUTES);
- if (!(spd_value & MODULE_REGISTERED) || (spd_value < 0)) {
-
- print_debug("Skipping un-matched DIMMs - only dual-channel operation supported\n");
- continue;
- }
-#ifdef VALIDATE_DIMM_COMPATIBILITY
- spd_value =
- spd_read_byte(channel1_dimm,
- SPD_SUPPORTED_BURST_LENGTHS);
- if (!(spd_value & SPD_BURST_LENGTH_4) || (spd_value < 0))
- continue;
-
- int j;
- for (j = 0; j < sizeof(dual_channel_parameters); ++j) {
- if (!are_spd_values_equal
- (dual_channel_parameters[j], channel0_dimm,
- channel1_dimm)) {
-
- bDualChannel = 0;
- break;
- }
- }
-#endif
-
- // Code around ROMCC bug in optimization of "if" statements
-#ifdef ROMCC_IF_BUG_FIXED
- if (bDualChannel) {
- // Made it through all the checks, this DIMM pair is usable
- dimm_mask |= ((1 << i) | (1 << (MAX_DIMM_SOCKETS_PER_CHANNEL + i)));
- } else
- print_debug("Skipping un-matched DIMMs - only dual-channel operation supported\n");
-#else
- switch (bDualChannel) {
- case 0:
- print_debug("Skipping un-matched DIMMs - only dual-channel operation supported\n");
- break;
-
- default:
- // Made it through all the checks, this DIMM pair is usable
- dimm_mask |= (1 << i) | (1 << (MAX_DIMM_SOCKETS_PER_CHANNEL + i));
- break;
- }
-#endif
- }
-
- return dimm_mask;
-}
-
-/*-----------------------------------------------------------------------------
-SDRAM configuration functions:
------------------------------------------------------------------------------*/
-
-/**
- * Send the specified command to all DIMMs.
- *
- * @param command Specifies the command to be sent to the DIMMs.
- * @param jedec_mode_bits For the MRS & EMRS commands, bits 0-12 contain the
- * register value in JEDEC format.
- */
-static void do_ram_command(uint8_t command, uint16_t jedec_mode_bits)
-{
- int i;
- uint32_t dram_controller_mode;
- uint8_t dimm_start_64M_multiple = 0;
- uint16_t e7501_mode_bits = jedec_mode_bits;
-
- // Configure the RAM command
- dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC);
- dram_controller_mode &= 0xFFFFFF8F;
- dram_controller_mode |= command;
- pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode);
-
- // RAM_COMMAND_NORMAL is an exception.
- // It affects only the memory controller and does not need to be "sent" to the DIMMs.
-
- if (command != RAM_COMMAND_NORMAL) {
-
- // Send the command to all DIMMs by accessing a memory location within each
- // NOTE: for mode select commands, some of the location address bits
- // are part of the command
-
- // Map JEDEC mode bits to E7501
- if (command == RAM_COMMAND_MRS) {
- // Host address lines [15:5] map to DIMM address lines [12:11, 9:1]
- // The E7501 hard-sets DIMM address lines 10 & 0 to zero
-
- ASSERT(!(jedec_mode_bits & 0x0401));
-
- e7501_mode_bits = ((jedec_mode_bits & 0x1800) << (15 - 12)) | // JEDEC bits 11-12 move to bits 14-15
- ((jedec_mode_bits & 0x03FE) << (13 - 9)); // JEDEC bits 1-9 move to bits 5-13
-
- } else if (command == RAM_COMMAND_EMRS) {
- // Host address lines [15:3] map to DIMM address lines [12:0]
- e7501_mode_bits = jedec_mode_bits <<= 3;
- } else
- ASSERT(jedec_mode_bits == 0);
-
- dimm_start_64M_multiple = 0;
-
- for (i = 0; i < (MAX_NUM_CHANNELS * MAX_DIMM_SOCKETS_PER_CHANNEL); ++i) {
-
- uint8_t dimm_end_64M_multiple =
- pci_read_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + i);
- if (dimm_end_64M_multiple > dimm_start_64M_multiple) {
-
- // This code assumes DRAM row boundaries are all set below 4 GB
- // NOTE: 0x40 * 64 MB == 4 GB
- ASSERT(dimm_start_64M_multiple < 0x40);
-
- // NOTE: 2^26 == 64 MB
-
- uint32_t dimm_start_address =
- dimm_start_64M_multiple << 26;
-
- RAM_DEBUG_MESSAGE(" Sending RAM command to 0x");
- RAM_DEBUG_HEX32(dimm_start_address + e7501_mode_bits);
- RAM_DEBUG_MESSAGE("\n");
-
- read32(dimm_start_address + e7501_mode_bits);
-
- // Set the start of the next DIMM
- dimm_start_64M_multiple =
- dimm_end_64M_multiple;
- }
- }
- }
-}
-
-/**
- * Set the mode register of all DIMMs.
- *
- * The proper CAS# latency setting is added to the mode bits specified
- * by the caller.
- *
- * @param jedec_mode_bits For the MRS & EMRS commands, bits 0-12 contain the
- * register value in JEDEC format.
- */
-static void set_ram_mode(uint16_t jedec_mode_bits)
-{
- ASSERT(!(jedec_mode_bits & SDRAM_CAS_MASK));
-
- uint32_t dram_cas_latency =
- pci_read_config32(PCI_DEV(0, 0, 0), DRT) & DRT_CAS_MASK;
-
- switch (dram_cas_latency) {
- case DRT_CAS_2_5:
- jedec_mode_bits |= SDRAM_CAS_2_5;
- break;
-
- case DRT_CAS_2_0:
- jedec_mode_bits |= SDRAM_CAS_2_0;
- break;
-
- default:
- BUG();
- break;
- }
-
- do_ram_command(RAM_COMMAND_MRS, jedec_mode_bits);
-}
-
-/*-----------------------------------------------------------------------------
-DIMM-independant configuration functions:
------------------------------------------------------------------------------*/
-
-/**
- * Configure the E7501's DRAM Row Boundary (DRB) registers for the memory
- * present in the specified DIMM.
- *
- * @param dimm_log2_num_bits Specifies log2(number of bits) for each side of
- * the DIMM.
- * @param total_dram_64M_multiple Total DRAM in the system (as a multiple of
- * 64 MB) for DIMMs < dimm_index.
- * @param dimm_index Which DIMM pair is being processed
- * (0..MAX_DIMM_SOCKETS_PER_CHANNEL).
- * @return New multiple of 64 MB total DRAM in the system.
- */
-static uint8_t configure_dimm_row_boundaries(struct dimm_size dimm_log2_num_bits, uint8_t total_dram_64M_multiple, unsigned dimm_index)
-{
- int i;
-
- ASSERT(dimm_index < MAX_DIMM_SOCKETS_PER_CHANNEL);
-
- // DIMM sides must be at least 32 MB
- ASSERT(dimm_log2_num_bits.side1 >= 28);
- ASSERT((dimm_log2_num_bits.side2 == 0)
- || (dimm_log2_num_bits.side2 >= 28));
-
- // In dual-channel mode, we are called only once for each pair of DIMMs.
- // Each time we process twice the capacity of a single DIMM.
-
- // Convert single DIMM capacity to paired DIMM capacity
- // (multiply by two ==> add 1 to log2)
- dimm_log2_num_bits.side1++;
- if (dimm_log2_num_bits.side2 > 0)
- dimm_log2_num_bits.side2++;
-
- // Add the capacity of side 1 this DIMM pair (as a multiple of 64 MB)
- // to the total capacity of the system
- // NOTE: 64 MB == 512 Mb, and log2(512 Mb) == 29
-
- total_dram_64M_multiple += (1 << (dimm_log2_num_bits.side1 - 29));
-
- // Configure the boundary address for the row on side 1
- pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + (dimm_index << 1),
- total_dram_64M_multiple);
-
- // If the DIMMs are double-sided, add the capacity of side 2 this DIMM pair
- // (as a multiple of 64 MB) to the total capacity of the system
- if (dimm_log2_num_bits.side2 >= 29)
- total_dram_64M_multiple +=
- (1 << (dimm_log2_num_bits.side2 - 29));
-
- // Configure the boundary address for the row (if any) on side 2
- pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_1 + (dimm_index << 1),
- total_dram_64M_multiple);
-
- // Update boundaries for rows subsequent to these.
- // These settings will be overridden by a subsequent call if a populated physical slot exists
-
- for (i = dimm_index + 1; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) {
- pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + (i << 1),
- total_dram_64M_multiple);
- pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_1 + (i << 1),
- total_dram_64M_multiple);
- }
-
- return total_dram_64M_multiple;
-}
-
-/**
- * Set the E7501's DRAM row boundary addresses & its Top Of Low Memory (TOLM).
- *
- * If necessary, set up a remap window so we don't waste DRAM that ordinarily
- * would lie behind addresses reserved for memory-mapped I/O.
- *
- * @param ctrl PCI addresses of memory controller functions, and SMBus
- * addresses of DIMM slots on the mainboard.
- * @param dimm_mask Bitmask of populated DIMMs, see spd_get_supported_dimms().
- */
-static void configure_e7501_ram_addresses(const struct mem_controller
- *ctrl, uint8_t dimm_mask)
-{
- int i;
- uint8_t total_dram_64M_multiple = 0;
-
- // Configure the E7501's DRAM row boundaries
- // Start by zeroing out the temporary initial configuration
- pci_write_config32(PCI_DEV(0, 0, 0), DRB_ROW_0, 0);
- pci_write_config32(PCI_DEV(0, 0, 0), DRB_ROW_4, 0);
-
- for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) {
-
- uint16_t dimm_socket_address = ctrl->channel0[i];
- struct dimm_size sz;
-
- if (!(dimm_mask & (1 << i)))
- continue; // This DIMM not present
-
- sz = spd_get_dimm_size(dimm_socket_address);
-
- RAM_DEBUG_MESSAGE("dimm size =");
- RAM_DEBUG_HEX32((u32)sz.side1);
- RAM_DEBUG_MESSAGE(" ");
- RAM_DEBUG_HEX32((u32)sz.side2);
- RAM_DEBUG_MESSAGE("\n");
-
- if (sz.side1 == 0)
- die("Bad SPD value\n");
-
- total_dram_64M_multiple =
- configure_dimm_row_boundaries(sz, total_dram_64M_multiple, i);
- }
-
- // Configure the Top Of Low Memory (TOLM) in the E7501
- // This address must be a multiple of 128 MB that is less than 4 GB.
- // NOTE: 16-bit wide TOLM register stores only the highest 5 bits of a 32-bit address
- // in the highest 5 bits.
-
- // We set TOLM to the smaller of 0xC0000000 (3 GB) or the total DRAM in the system.
- // This reserves addresses from 0xC0000000 - 0xFFFFFFFF for non-DRAM purposes
- // such as flash and memory-mapped I/O.
-
- // If there is more than 3 GB of DRAM, we define a remap window which
- // makes the DRAM "behind" the reserved region available above the top of physical
- // memory.
-
- // NOTE: 0xC0000000 / (64 MB) == 0x30
-
- if (total_dram_64M_multiple <= 0x30) {
-
- // <= 3 GB total RAM
-
- /* I should really adjust all of this in C after I have resources
- * to all of the pci devices.
- */
-
- // Round up to 128MB granularity
- // SJM: Is "missing" 64 MB of memory a potential issue? Should this round down?
-
- uint8_t total_dram_128M_multiple =
- (total_dram_64M_multiple + 1) >> 1;
-
- // Convert to high 16 bits of address
- uint16_t top_of_low_memory =
- total_dram_128M_multiple << 11;
-
- pci_write_config16(PCI_DEV(0, 0, 0), TOLM,
- top_of_low_memory);
-
- } else {
-
- // > 3 GB total RAM
-
- // Set defaults for > 4 GB DRAM, i.e. remap a 1 GB (= 0x10 * 64 MB) range of memory
- uint16_t remap_base = total_dram_64M_multiple; // A[25:0] == 0
- uint16_t remap_limit = total_dram_64M_multiple + 0x10 - 1; // A[25:0] == 0xF
-
- // Put TOLM at 3 GB
-
- pci_write_config16(PCI_DEV(0, 0, 0), TOLM, 0xc000);
-
- // Define a remap window to make the RAM that would appear from 3 GB - 4 GB
- // visible just beyond 4 GB or the end of physical memory, whichever is larger
- // NOTE: 16-bit wide REMAP registers store only the highest 10 bits of a 36-bit address,
- // (i.e. a multiple of 64 MB) in the lowest 10 bits.
- // NOTE: 0x100000000 / (64 MB) == 0x40
-
- if (total_dram_64M_multiple < 0x40) {
- remap_base = 0x40; // 0x100000000
- remap_limit =
- 0x40 + (total_dram_64M_multiple - 0x30) - 1;
- }
-
- pci_write_config16(PCI_DEV(0, 0, 0), REMAPBASE,
- remap_base);
- pci_write_config16(PCI_DEV(0, 0, 0), REMAPLIMIT,
- remap_limit);
- }
-}
-
-/**
- * If we're configured to use ECC, initialize the SDRAM and clear the E7501's
- * ECC error flags.
- */
-static void initialize_ecc(void)
-{
- uint32_t dram_controller_mode;
-
- /* Test to see if ECC support is enabled */
- dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC);
- dram_controller_mode >>= 20;
- dram_controller_mode &= 3;
- if (dram_controller_mode == 2) {
-
- uint8_t byte;
-
- RAM_DEBUG_MESSAGE("Initializing ECC state...\n");
- /* Initialize ECC bits , use ECC zero mode (new to 7501) */
- pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 0x06);
- pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 0x07);
-
- // Wait for scrub cycle to complete
- do {
- byte =
- pci_read_config8(PCI_DEV(0, 0, 0), MCHCFGNS);
- } while ((byte & 0x08) == 0);
-
- pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, byte & 0xfc);
- RAM_DEBUG_MESSAGE("ECC state initialized.\n");
-
- /* Clear the ECC error bits */
- pci_write_config8(PCI_DEV(0, 0, 1), DRAM_FERR, 0x03);
- pci_write_config8(PCI_DEV(0, 0, 1), DRAM_NERR, 0x03);
-
- // Clear DRAM Interface error bits (write-one-clear)
- pci_write_config32(PCI_DEV(0, 0, 1), FERR_GLOBAL, 1 << 18);
- pci_write_config32(PCI_DEV(0, 0, 1), NERR_GLOBAL, 1 << 18);
-
- // Start normal ECC scrub
- pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 5);
- }
-
-}
-
-/**
- * Program the DRAM Timing register (DRT) of the E7501 (except for CAS#
- * latency, which is assumed to have been programmed already), based on the
- * parameters of the various installed DIMMs.
- *
- * @param ctrl PCI addresses of memory controller functions, and SMBus
- * addresses of DIMM slots on the mainboard.
- * @param dimm_mask Bitmask of populated DIMMs, see spd_get_supported_dimms().
- */
-static void configure_e7501_dram_timing(const struct mem_controller *ctrl,
- uint8_t dimm_mask)
-{
- int i;
- uint32_t dram_timing;
- int value;
- uint8_t slowest_row_precharge = 0;
- uint8_t slowest_ras_cas_delay = 0;
- uint8_t slowest_active_to_precharge_delay = 0;
- uint32_t current_cas_latency =
- pci_read_config32(PCI_DEV(0, 0, 0), DRT) & DRT_CAS_MASK;
-
- // CAS# latency must be programmed beforehand
- ASSERT((current_cas_latency == DRT_CAS_2_0)
- || (current_cas_latency == DRT_CAS_2_5));
-
- // Each timing parameter is determined by the slowest DIMM
-
- for (i = 0; i < MAX_DIMM_SOCKETS; i++) {
- uint16_t dimm_socket_address;
-
- if (!(dimm_mask & (1 << i)))
- continue; // This DIMM not present
-
- if (i < MAX_DIMM_SOCKETS_PER_CHANNEL)
- dimm_socket_address = ctrl->channel0[i];
- else
- dimm_socket_address =
- ctrl->channel1[i - MAX_DIMM_SOCKETS_PER_CHANNEL];
-
- value =
- spd_read_byte(dimm_socket_address,
- SPD_MIN_ROW_PRECHARGE_TIME);
- if (value < 0)
- goto hw_err;
- if (value > slowest_row_precharge)
- slowest_row_precharge = value;
-
- value =
- spd_read_byte(dimm_socket_address,
- SPD_MIN_RAS_TO_CAS_DELAY);
- if (value < 0)
- goto hw_err;
- if (value > slowest_ras_cas_delay)
- slowest_ras_cas_delay = value;
-
- value =
- spd_read_byte(dimm_socket_address,
- SPD_MIN_ACTIVE_TO_PRECHARGE_DELAY);
- if (value < 0)
- goto hw_err;
- if (value > slowest_active_to_precharge_delay)
- slowest_active_to_precharge_delay = value;
- }
-
- // NOTE for timing parameters:
- // At 133 MHz, 1 clock == 7.52 ns
-
- /* Read the initial state */
- dram_timing = pci_read_config32(PCI_DEV(0, 0, 0), DRT);
-
- /* Trp */
-
- // E7501 supports only 2 or 3 clocks for tRP
- if (slowest_row_precharge > ((22 << 2) | (2 << 0)))
- die("unsupported DIMM tRP"); // > 22.5 ns: 4 or more clocks
- else if (slowest_row_precharge > (15 << 2))
- dram_timing &= ~(1 << 0); // > 15.0 ns: 3 clocks
- else
- dram_timing |= (1 << 0); // <= 15.0 ns: 2 clocks
-
- /* Trcd */
-
- // E7501 supports only 2 or 3 clocks for tRCD
- // Use the same value for both read & write
- dram_timing &= ~((1 << 3) | (3 << 1));
- if (slowest_ras_cas_delay > ((22 << 2) | (2 << 0)))
- die("unsupported DIMM tRCD"); // > 22.5 ns: 4 or more clocks
- else if (slowest_ras_cas_delay > (15 << 2))
- dram_timing |= (2 << 1); // > 15.0 ns: 3 clocks
- else
- dram_timing |= ((1 << 3) | (3 << 1)); // <= 15.0 ns: 2 clocks
-
- /* Tras */
-
- // E7501 supports only 5, 6, or 7 clocks for tRAS
- // 5 clocks ~= 37.6 ns, 6 clocks ~= 45.1 ns, 7 clocks ~= 52.6 ns
- dram_timing &= ~(3 << 9);
-
- if (slowest_active_to_precharge_delay > 52)
- die("unsupported DIMM tRAS"); // > 52 ns: 8 or more clocks
- else if (slowest_active_to_precharge_delay > 45)
- dram_timing |= (0 << 9); // 46-52 ns: 7 clocks
- else if (slowest_active_to_precharge_delay > 37)
- dram_timing |= (1 << 9); // 38-45 ns: 6 clocks
- else
- dram_timing |= (2 << 9); // < 38 ns: 5 clocks
-
- /* Trd */
-
- /* Set to a 7 clock read delay. This is for 133MHz
- * with a CAS latency of 2.5 if 2.0 a 6 clock
- * delay is good */
-
- dram_timing &= ~(7 << 24); // 7 clocks
- if (current_cas_latency == DRT_CAS_2_0)
- dram_timing |= (1 << 24); // 6 clocks
-
- /*
- * Back to Back Read-Write Turn Around
- */
- /* Set to a 5 clock back to back read to write turn around.
- * 4 is a good delay if the CAS latency is 2.0 */
-
- dram_timing &= ~(1 << 28); // 5 clocks
- if (current_cas_latency == DRT_CAS_2_0)
- dram_timing |= (1 << 28); // 4 clocks
-
- pci_write_config32(PCI_DEV(0, 0, 0), DRT, dram_timing);
-
- return;
-
- hw_err:
- die(SPD_ERROR);
-}
-
-/**
- * Determine the shortest CAS# latency that the E7501 and all DIMMs have in
- * common, and program the E7501 to use it.
- *
- * @param ctrl PCI addresses of memory controller functions, and SMBus
- * addresses of DIMM slots on the mainboard.
- * @param dimm_mask Bitmask of populated DIMMs, spd_get_supported_dimms().
- */
-static void configure_e7501_cas_latency(const struct mem_controller *ctrl,
- uint8_t dimm_mask)
-{
- int i;
- int value;
- uint32_t dram_timing;
- uint16_t maybe_dram_read_timing;
- uint32_t dword;
-
- // CAS# latency bitmasks in SPD_ACCEPTABLE_CAS_LATENCIES format
- // NOTE: E7501 supports only 2.0 and 2.5
- uint32_t system_compatible_cas_latencies =
- SPD_CAS_LATENCY_2_0 | SPD_CAS_LATENCY_2_5;
- uint32_t current_cas_latency;
- uint32_t dimm_compatible_cas_latencies;
-
- for (i = 0; i < MAX_DIMM_SOCKETS; i++) {
-
- uint16_t dimm_socket_address;
-
- if (!(dimm_mask & (1 << i)))
- continue; // This DIMM not usable
-
- if (i < MAX_DIMM_SOCKETS_PER_CHANNEL)
- dimm_socket_address = ctrl->channel0[i];
- else
- dimm_socket_address =
- ctrl->channel1[i - MAX_DIMM_SOCKETS_PER_CHANNEL];
-
- value =
- spd_read_byte(dimm_socket_address,
- SPD_ACCEPTABLE_CAS_LATENCIES);
- if (value < 0)
- goto hw_err;
-
- dimm_compatible_cas_latencies = value & 0x7f; // Start with all supported by DIMM
- current_cas_latency = 1 << log2(dimm_compatible_cas_latencies); // Max supported by DIMM
-
- // Can we support the highest CAS# latency?
-
- value =
- spd_read_byte(dimm_socket_address,
- SPD_MIN_CYCLE_TIME_AT_CAS_MAX);
- if (value < 0)
- goto hw_err;
-
- // NOTE: At 133 MHz, 1 clock == 7.52 ns
- if (value > 0x75) {
- // Our bus is too fast for this CAS# latency
- // Remove it from the bitmask of those supported by the DIMM that are compatible
- dimm_compatible_cas_latencies &= ~current_cas_latency;
- }
- // Can we support the next-highest CAS# latency (max - 0.5)?
-
- current_cas_latency >>= 1;
- if (current_cas_latency != 0) {
- value =
- spd_read_byte(dimm_socket_address,
- SPD_SDRAM_CYCLE_TIME_2ND);
- if (value < 0)
- goto hw_err;
- if (value > 0x75)
- dimm_compatible_cas_latencies &=
- ~current_cas_latency;
- }
- // Can we support the next-highest CAS# latency (max - 1.0)?
- current_cas_latency >>= 1;
- if (current_cas_latency != 0) {
- value =
- spd_read_byte(dimm_socket_address,
- SPD_SDRAM_CYCLE_TIME_3RD);
- if (value < 0)
- goto hw_err;
- if (value > 0x75)
- dimm_compatible_cas_latencies &=
- ~current_cas_latency;
- }
- // Restrict the system to CAS# latencies compatible with this DIMM
- system_compatible_cas_latencies &=
- dimm_compatible_cas_latencies;
-
- /* go to the next DIMM */
- }
-
- /* After all of the arduous calculation setup with the fastest
- * cas latency I can use.
- */
-
- dram_timing = pci_read_config32(PCI_DEV(0, 0, 0), DRT);
- dram_timing &= ~(DRT_CAS_MASK);
-
- maybe_dram_read_timing =
- pci_read_config16(PCI_DEV(0, 0, 0), MAYBE_DRDCTL);
- maybe_dram_read_timing &= 0xF00C;
-
- if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_0) {
- dram_timing |= DRT_CAS_2_0;
- maybe_dram_read_timing |= 0xBB1;
- } else if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_5) {
-
- uint32_t dram_row_attributes =
- pci_read_config32(PCI_DEV(0, 0, 0), DRA);
-
- dram_timing |= DRT_CAS_2_5;
-
- // At CAS# 2.5, DRAM Read Timing (if that's what it its) appears to need a slightly
- // different value if all DIMM slots are populated
-
- if ((dram_row_attributes & 0xff)
- && (dram_row_attributes & 0xff00)
- && (dram_row_attributes & 0xff0000)
- && (dram_row_attributes & 0xff000000)) {
-
- // All slots populated
- maybe_dram_read_timing |= 0x0882;
- } else {
- // Some unpopulated slots
- maybe_dram_read_timing |= 0x0662;
- }
- } else
- die("No CAS# latencies compatible with all DIMMs!!\n");
-
- pci_write_config32(PCI_DEV(0, 0, 0), DRT, dram_timing);
-
- /* set master DLL reset */
- dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88);
- dword |= (1 << 26);
- pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword);
-
- dword &= 0x0c0007ff; /* patch try register 88 is undocumented tnz */
- dword |= 0xd2109800;
-
- pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword);
-
- pci_write_config16(PCI_DEV(0, 0, 0), MAYBE_DRDCTL,
- maybe_dram_read_timing);
-
- dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88); /* reset master DLL reset */
- dword &= ~(1 << 26);
- pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword);
-
- return;
-
- hw_err:
- die(SPD_ERROR);
-}
-
-/**
- * Configure the refresh interval so that we refresh no more often than
- * required by the "most needy" DIMM. Also disable ECC if any of the DIMMs
- * don't support it.
- *
- * @param ctrl PCI addresses of memory controller functions, and SMBus
- * addresses of DIMM slots on the mainboard.
- * @param dimm_mask Bitmask of populated DIMMs, spd_get_supported_dimms().
- */
-static void configure_e7501_dram_controller_mode(const struct
- mem_controller *ctrl,
- uint8_t dimm_mask)
-{
- int i;
-
- // Initial settings
- uint32_t controller_mode =
- pci_read_config32(PCI_DEV(0, 0, 0), DRC);
- uint32_t system_refresh_mode = (controller_mode >> 8) & 7;
-
- // Code below assumes that most aggressive settings are in
- // force when we are called, either via E7501 reset defaults
- // or by sdram_set_registers():
- // - ECC enabled
- // - No refresh
-
- ASSERT((controller_mode & (3 << 20)) == (2 << 20)); // ECC
- ASSERT(!(controller_mode & (7 << 8))); // Refresh
-
- /* Walk through _all_ dimms and find the least-common denominator for:
- * - ECC support
- * - refresh rates
- */
-
- for (i = 0; i < MAX_DIMM_SOCKETS; i++) {
-
- uint32_t dimm_refresh_mode;
- int value;
- uint16_t dimm_socket_address;
-
- if (!(dimm_mask & (1 << i))) {
- continue; // This DIMM not usable
- }
-
- if (i < MAX_DIMM_SOCKETS_PER_CHANNEL)
- dimm_socket_address = ctrl->channel0[i];
- else
- dimm_socket_address =
- ctrl->channel1[i -
- MAX_DIMM_SOCKETS_PER_CHANNEL];
-
- // Disable ECC mode if any one of the DIMMs does not support ECC
- // SJM: Should we just die here? E7501 datasheet says non-ECC DIMMs aren't supported.
-
- value =
- spd_read_byte(dimm_socket_address,
- SPD_DIMM_CONFIG_TYPE);
- die_on_spd_error(value);
- if (value != ERROR_SCHEME_ECC) {
- controller_mode &= ~(3 << 20);
- }
-
- value = spd_read_byte(dimm_socket_address, SPD_REFRESH);
- die_on_spd_error(value);
- value &= 0x7f; // Mask off self-refresh bit
- if (value > MAX_SPD_REFRESH_RATE) {
- print_err("unsupported refresh rate\n");
- continue;
- }
- // Get the appropriate E7501 refresh mode for this DIMM
- dimm_refresh_mode = refresh_rate_map[value];
- if (dimm_refresh_mode > 7) {
- print_err("unsupported refresh rate\n");
- continue;
- }
- // If this DIMM requires more frequent refresh than others,
- // update the system setting
- if (refresh_frequency[dimm_refresh_mode] >
- refresh_frequency[system_refresh_mode])
- system_refresh_mode = dimm_refresh_mode;
-
-#ifdef SUSPICIOUS_LOOKING_CODE
-// SJM NOTE: This code doesn't look right. SPD values are an order of magnitude smaller
-// than the clock period of the memory controller. Also, no other northbridge
-// looks at SPD_CMD_SIGNAL_INPUT_HOLD_TIME.
-
- // Switch to 2 clocks for address/command if required by any one of the DIMMs
- // NOTE: At 133 MHz, 1 clock == 7.52 ns
- value =
- spd_read_byte(dimm_socket_address,
- SPD_CMD_SIGNAL_INPUT_HOLD_TIME);
- die_on_spd_error(value);
- if (value >= 0xa0) { /* At 133MHz this constant should be 0x75 */
- controller_mode &= ~(1 << 16); /* Use two clock cyles instead of one */
- }
-#endif
-
- /* go to the next DIMM */
- }
-
- controller_mode |= (system_refresh_mode << 8);
-
- // Configure the E7501
- pci_write_config32(PCI_DEV(0, 0, 0), DRC, controller_mode);
-}
-
-/**
- * Configure the E7501's DRAM Row Attributes (DRA) registers based on DIMM
- * parameters read via SPD. This tells the controller the width of the SDRAM
- * chips on each DIMM side (x4 or x8) and the page size of each DIMM side
- * (4, 8, 16, or 32 KB).
- *
- * @param ctrl PCI addresses of memory controller functions, and SMBus
- * addresses of DIMM slots on the mainboard.
- * @param dimm_mask Bitmask of populated DIMMs, spd_get_supported_dimms().
- */
-static void configure_e7501_row_attributes(const struct mem_controller
- *ctrl, uint8_t dimm_mask)
-{
- int i;
- uint32_t row_attributes = 0;
-
- for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) {
-
- uint16_t dimm_socket_address = ctrl->channel0[i];
- struct dimm_size page_size;
- struct dimm_size sdram_width;
-
- if (!(dimm_mask & (1 << i)))
- continue; // This DIMM not usable
-
- // Get the relevant parameters via SPD
- page_size = sdram_spd_get_page_size(dimm_socket_address);
- sdram_width = sdram_spd_get_width(dimm_socket_address);
-
- // Update the DRAM Row Attributes.
- // Page size is encoded as log2(page size in bits) - log2(8 Kb)
- // NOTE: 8 Kb = 2^13
- row_attributes |= (page_size.side1 - 13) << (i << 3); // Side 1 of each DIMM is an EVEN row
-
- if (sdram_width.side2 > 0)
- row_attributes |= (page_size.side2 - 13) << ((i << 3) + 4); // Side 2 is ODD
-
- // Set x4 flags if appropriate
- if (sdram_width.side1 == 4) {
- row_attributes |= 0x08 << (i << 3);
- }
-
- if (sdram_width.side2 == 4) {
- row_attributes |= 0x08 << ((i << 3) + 4);
- }
-
- /* go to the next DIMM */
- }
-
- /* Write the new row attributes register */
- pci_write_config32(PCI_DEV(0, 0, 0), DRA, row_attributes);
-}
-
-/*
- * Enable clock signals for populated DIMM sockets and disable them for
- * unpopulated sockets (to reduce EMI).
- *
- * @param dimm_mask Bitmask of populated DIMMs, see spd_get_supported_dimms().
- */
-static void enable_e7501_clocks(uint8_t dimm_mask)
-{
- int i;
- uint8_t clock_disable = pci_read_config8(PCI_DEV(0, 0, 0), CKDIS);
-
- for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) {
-
- uint8_t socket_mask = 1 << i;
-
- if (dimm_mask & socket_mask)
- clock_disable &= ~socket_mask; // DIMM present, enable clock
- else
- clock_disable |= socket_mask; // DIMM absent, disable clock
- }
-
- pci_write_config8(PCI_DEV(0, 0, 0), CKDIS, clock_disable);
-}
-
-/* DIMM-dedependent configuration functions */
-
-/**
- * DDR Receive FIFO RE-Sync (?)
- */
-static void RAM_RESET_DDR_PTR(void)
-{
- uint8_t byte;
- byte = pci_read_config8(PCI_DEV(0, 0, 0), 0x88);
- byte |= (1 << 4);
- pci_write_config8(PCI_DEV(0, 0, 0), 0x88, byte);
-
- byte = pci_read_config8(PCI_DEV(0, 0, 0), 0x88);
- byte &= ~(1 << 4);
- pci_write_config8(PCI_DEV(0, 0, 0), 0x88, byte);
-}
-
-/**
- * Set E7501 registers that are either independent of DIMM specifics, or
- * establish default settings that will be overridden when we learn the
- * specifics.
- *
- * This sets PCI configuration registers to known good values based on the
- * table 'constant_register_values', which are a triple of configuration
- * register offset, mask, and bits to set.
- */
-static void ram_set_d0f0_regs(void)
-{
- int i;
- int num_values = ARRAY_SIZE(constant_register_values);
-
- ASSERT((num_values % 3) == 0); // Bad table?
-
- for (i = 0; i < num_values; i += 3) {
-
- uint32_t register_offset = constant_register_values[i];
- uint32_t bits_to_mask = constant_register_values[i + 1];
- uint32_t bits_to_set = constant_register_values[i + 2];
- uint32_t register_value;
-
- // It's theoretically possible to set values for something other than D0:F0,
- // but it's not typically done here
- ASSERT(!(register_offset & 0xFFFFFF00));
-
- // bits_to_mask and bits_to_set should not reference the same bits
- // Again, not strictly an error, but flagged as a potential bug
- ASSERT((bits_to_mask & bits_to_set) == 0);
-
- register_value =
- pci_read_config32(PCI_DEV(0, 0, 0), register_offset);
- register_value &= bits_to_mask;
- register_value |= bits_to_set;
-
- pci_write_config32(PCI_DEV(0, 0, 0), register_offset,
- register_value);
- }
-}
-
-/**
- * Copy 64 bytes from one location to another.
- *
- * @param src_addr TODO
- * @param dst_addr TODO
- */
-static void write_8dwords(const uint32_t *src_addr, uint32_t dst_addr)
-{
- int i;
- for (i = 0; i < 8; i++) {
- write32(dst_addr, *src_addr);
- src_addr++;
- dst_addr += sizeof(uint32_t);
- }
-}
-
-/**
- * Set the E7501's (undocumented) RCOMP registers.
- *
- * Per the 855PM datasheet and IXP2800 HW Initialization Reference Manual,
- * RCOMP registers appear to affect drive strength, pullup/pulldown offset,
- * and slew rate of various signal groups.
- *
- * Comments below are conjecture based on apparent similarity between the
- * E7501 and these two chips.
- */
-static void ram_set_rcomp_regs(void)
-{
- uint32_t dword;
- uint8_t maybe_strength_control;
-
- RAM_DEBUG_MESSAGE("Setting RCOMP registers.\n");
-
- /*enable access to the rcomp bar */
- dword = pci_read_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST);
- dword |= (1 << 22);
- pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST, dword);
-
- // Set the RCOMP MMIO base address
- pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_SMRBASE, RCOMP_MMIO);
-
- // Block RCOMP updates while we configure the registers
- dword = read32(RCOMP_MMIO + MAYBE_SMRCTL);
- dword |= (1 << 9);
- write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
-
- /* Begin to write the RCOMP registers */
-
- // Set CMD and DQ/DQS strength to 2x (?)
- maybe_strength_control = read8(RCOMP_MMIO + MAYBE_DQCMDSTR) & 0x88;
- maybe_strength_control |= 0x44;
- write8(RCOMP_MMIO + MAYBE_DQCMDSTR, maybe_strength_control);
-
- write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x80);
- write16(RCOMP_MMIO + 0x42, 0);
-
- write_8dwords(maybe_1x_slew_table, RCOMP_MMIO + 0x60);
-
- // NOTE: some factory BIOS set 0x9088 here. Seems to work either way.
- write16(RCOMP_MMIO + 0x40, 0);
-
- // Set RCVEnOut# strength to 2x (?)
- maybe_strength_control = read8(RCOMP_MMIO + MAYBE_RCVENSTR) & 0xF8;
- maybe_strength_control |= 4;
- write8(RCOMP_MMIO + MAYBE_RCVENSTR, maybe_strength_control);
-
- write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x1c0);
- write16(RCOMP_MMIO + 0x50, 0);
-
- // Set CS# strength for x4 SDRAM to 2x (?)
- maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CSBSTR) & 0xF8;
- maybe_strength_control |= 4;
- write8(RCOMP_MMIO + MAYBE_CSBSTR, maybe_strength_control);
-
- write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x140);
- write16(RCOMP_MMIO + 0x48, 0);
-
- // Set CKE strength for x4 SDRAM to 2x (?)
- maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKESTR) & 0xF8;
- maybe_strength_control |= 4;
- write8(RCOMP_MMIO + MAYBE_CKESTR, maybe_strength_control);
-
- write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0xa0);
- write16(RCOMP_MMIO + 0x44, 0);
-
- // Set CK strength for x4 SDRAM to 1x (?)
- maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKSTR) & 0xF8;
- maybe_strength_control |= 1;
- write8(RCOMP_MMIO + MAYBE_CKSTR, maybe_strength_control);
-
- write_8dwords(maybe_pull_updown_offset_table, RCOMP_MMIO + 0x180);
- write16(RCOMP_MMIO + 0x4c, 0);
-
- write8(RCOMP_MMIO + 0x2c, 0xff);
-
- // Set the digital filter length to 8 (?)
- dword = read32(RCOMP_MMIO + MAYBE_SMRCTL);
-
- // NOTE: Some factory BIOS don't do this.
- // Doesn't seem to matter either way.
- dword &= ~2;
-
- dword |= 1;
- write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
-
- /* Wait 40 usec */
- SLOW_DOWN_IO;
-
- /* unblock updates */
- dword = read32(RCOMP_MMIO + MAYBE_SMRCTL);
- dword &= ~(1 << 9);
- write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
-
- // Force a RCOMP measurement cycle?
- dword |= (1 << 8);
- write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
- dword &= ~(1 << 8);
- write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
-
- /* Wait 40 usec */
- SLOW_DOWN_IO;
-
- /*disable access to the rcomp bar */
- dword = pci_read_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST);
- dword &= ~(1 << 22);
- pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST, dword);
-
-}
-
-/*-----------------------------------------------------------------------------
-Public interface:
------------------------------------------------------------------------------*/
-
-/**
- * Go through the JEDEC initialization sequence for all DIMMs, then enable
- * refresh and initialize ECC and memory to zero. Upon exit, SDRAM is up
- * and running.
- *
- * @param controllers Not used.
- * @param ctrl PCI addresses of memory controller functions, and SMBus
- * addresses of DIMM slots on the mainboard.
- */
-static void sdram_enable(int controllers,
- const struct mem_controller *ctrl)
-{
- uint8_t dimm_mask = pci_read_config16(PCI_DEV(0, 0, 0), SKPD);
- uint32_t dram_controller_mode;
-
- if (dimm_mask == 0)
- return;
-
- /* 1 & 2 Power up and start clocks */
- RAM_DEBUG_MESSAGE("Ram Enable 1\n");
- RAM_DEBUG_MESSAGE("Ram Enable 2\n");
-
- /* A 200us delay is needed */
- DO_DELAY; EXTRA_DELAY;
-
- /* 3. Apply NOP */
- RAM_DEBUG_MESSAGE("Ram Enable 3\n");
- do_ram_command(RAM_COMMAND_NOP, 0);
- EXTRA_DELAY;
-
- /* 4 Precharge all */
- RAM_DEBUG_MESSAGE("Ram Enable 4\n");
- do_ram_command(RAM_COMMAND_PRECHARGE, 0);
- EXTRA_DELAY;
- /* wait until the all banks idle state... */
-
- /* 5. Issue EMRS to enable DLL */
- RAM_DEBUG_MESSAGE("Ram Enable 5\n");
- do_ram_command(RAM_COMMAND_EMRS,
- SDRAM_EXTMODE_DLL_ENABLE |
- SDRAM_EXTMODE_DRIVE_NORMAL);
- EXTRA_DELAY;
-
- /* 6. Reset DLL */
- RAM_DEBUG_MESSAGE("Ram Enable 6\n");
- set_ram_mode(E7501_SDRAM_MODE | SDRAM_MODE_DLL_RESET);
- EXTRA_DELAY;
- /* Ensure a 200us delay between the DLL reset in step 6 and the final
- * mode register set in step 9.
- * Infineon needs this before any other command is sent to the ram.
- */
- DO_DELAY; EXTRA_DELAY;
-
- /* 7 Precharge all */
- RAM_DEBUG_MESSAGE("Ram Enable 7\n");
- do_ram_command(RAM_COMMAND_PRECHARGE, 0);
- EXTRA_DELAY;
-
- /* 8 Now we need 2 AUTO REFRESH / CBR cycles to be performed */
- RAM_DEBUG_MESSAGE("Ram Enable 8\n");
- do_ram_command(RAM_COMMAND_CBR, 0);
- EXTRA_DELAY;
- do_ram_command(RAM_COMMAND_CBR, 0);
- EXTRA_DELAY;
-
- /* And for good luck 6 more CBRs */
- do_ram_command(RAM_COMMAND_CBR, 0);
- EXTRA_DELAY;
- do_ram_command(RAM_COMMAND_CBR, 0);
- EXTRA_DELAY;
- do_ram_command(RAM_COMMAND_CBR, 0);
- EXTRA_DELAY;
- do_ram_command(RAM_COMMAND_CBR, 0);
- EXTRA_DELAY;
- do_ram_command(RAM_COMMAND_CBR, 0);
- EXTRA_DELAY;
- do_ram_command(RAM_COMMAND_CBR, 0);
- EXTRA_DELAY;
-
- /* 9 mode register set */
- RAM_DEBUG_MESSAGE("Ram Enable 9\n");
- set_ram_mode(E7501_SDRAM_MODE | SDRAM_MODE_NORMAL);
- EXTRA_DELAY;
-
- /* 10 DDR Receive FIFO RE-Sync */
- RAM_DEBUG_MESSAGE("Ram Enable 10\n");
- RAM_RESET_DDR_PTR();
- EXTRA_DELAY;
-
- /* 11 normal operation */
- RAM_DEBUG_MESSAGE("Ram Enable 11\n");
- do_ram_command(RAM_COMMAND_NORMAL, 0);
- EXTRA_DELAY;
-
- // Reconfigure the row boundaries and Top of Low Memory
- // to match the true size of the DIMMs
- configure_e7501_ram_addresses(ctrl, dimm_mask);
-
- /* Finally enable refresh */
- dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC);
- dram_controller_mode |= (1 << 29);
- pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode);
- EXTRA_DELAY;
- initialize_ecc();
-
- dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); /* FCS_EN */
- dram_controller_mode |= (1 << 17); // NOTE: undocumented reserved bit
- pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode);
-
- RAM_DEBUG_MESSAGE("Northbridge following SDRAM init:\n");
- DUMPNORTH();
-}
-
-/**
- * Configure SDRAM controller parameters that depend on characteristics of the
- * DIMMs installed in the system. These characteristics are read from the
- * DIMMs via the standard Serial Presence Detect (SPD) interface.
- *
- * @param ctrl PCI addresses of memory controller functions, and SMBus
- * addresses of DIMM slots on the mainboard.
- */
-static void sdram_set_spd_registers(const struct mem_controller *ctrl)
-{
- uint8_t dimm_mask;
-
- RAM_DEBUG_MESSAGE("Reading SPD data...\n");
-
- dimm_mask = spd_get_supported_dimms(ctrl);
-
- if (dimm_mask == 0) {
- print_debug("No usable memory for this controller\n");
- } else {
- enable_e7501_clocks(dimm_mask);
-
- RAM_DEBUG_MESSAGE("setting based on SPD data...\n");
-
- configure_e7501_row_attributes(ctrl, dimm_mask);
- configure_e7501_dram_controller_mode(ctrl, dimm_mask);
- configure_e7501_cas_latency(ctrl, dimm_mask);
- RAM_RESET_DDR_PTR();
-
- configure_e7501_dram_timing(ctrl, dimm_mask);
- DO_DELAY;
- RAM_DEBUG_MESSAGE("done\n");
- }
-
- /* NOTE: configure_e7501_ram_addresses() is NOT called here.
- * We want to keep the default 64 MB/row mapping until sdram_enable() is called,
- * even though the default mapping is almost certainly incorrect.
- * The default mapping makes it easy to initialize all of the DIMMs
- * even if the total system memory is > 4 GB.
- *
- * Save the dimm_mask for when sdram_enable is called, so it can call
- * configure_e7501_ram_addresses() without having to regenerate the bitmask
- * of usable DIMMs.
- */
- pci_write_config16(PCI_DEV(0, 0, 0), SKPD, dimm_mask);
-}
-
-/**
- * Do basic RAM setup that does NOT depend on serial presence detect
- * information (i.e. independent of DIMM specifics).
- *
- * @param ctrl PCI addresses of memory controller functions, and SMBus
- * addresses of DIMM slots on the mainboard.
- */
-static void sdram_set_registers(const struct mem_controller *ctrl)
-{
- RAM_DEBUG_MESSAGE("Northbridge prior to SDRAM init:\n");
- DUMPNORTH();
-
- ram_set_rcomp_regs();
- ram_set_d0f0_regs();
-}
diff --git a/src/northbridge/intel/e7501/raminit.h b/src/northbridge/intel/e7501/raminit.h
deleted file mode 100644
index 05c3889..0000000
--- a/src/northbridge/intel/e7501/raminit.h
+++ /dev/null
@@ -1,20 +0,0 @@
-#ifndef RAMINIT_H
-#define RAMINIT_H
-
-#define MAX_DIMM_SOCKETS_PER_CHANNEL 4
-#define MAX_NUM_CHANNELS 2
-#define MAX_DIMM_SOCKETS (MAX_NUM_CHANNELS * MAX_DIMM_SOCKETS_PER_CHANNEL)
-
-struct mem_controller {
- device_t d0, d0f1; // PCI bus/device/fcns of E7501 memory controller
-
- // SMBus addresses of DIMM slots for each channel,
- // in order from closest to MCH to furthest away
- // 0 == not present
- uint16_t channel0[MAX_DIMM_SOCKETS_PER_CHANNEL];
- uint16_t channel1[MAX_DIMM_SOCKETS_PER_CHANNEL];
-};
-
-void sdram_initialize(int controllers, const struct mem_controller *ctrl);
-
-#endif /* RAMINIT_H */
diff --git a/src/northbridge/intel/e7501/reset_test.c b/src/northbridge/intel/e7501/reset_test.c
deleted file mode 100644
index 1c0dad5..0000000
--- a/src/northbridge/intel/e7501/reset_test.c
+++ /dev/null
@@ -1,18 +0,0 @@
-/* Convert to C by yhlu */
-#define MCH_DRC 0x7c
-#define DRC_DONE (1 << 29)
- /* If I have already booted once skip a bunch of initialization */
- /* To see if I have already booted I check to see if memory
- * has been enabled.
- */
-static int bios_reset_detected(void) {
- uint32_t dword;
-
- dword = pci_read_config32(PCI_DEV(0, 0, 0), MCH_DRC);
-
- if( (dword & DRC_DONE) != 0 ) {
- return 1;
- }
-
- return 0;
-}
diff --git a/src/southbridge/intel/Kconfig b/src/southbridge/intel/Kconfig
index 426ac0b..26c1476 100644
--- a/src/southbridge/intel/Kconfig
+++ b/src/southbridge/intel/Kconfig
@@ -6,7 +6,6 @@ source src/southbridge/intel/i82801ax/Kconfig
source src/southbridge/intel/i82801bx/Kconfig
source src/southbridge/intel/i82801cx/Kconfig
source src/southbridge/intel/i82801dx/Kconfig
-source src/southbridge/intel/i82801ex/Kconfig
source src/southbridge/intel/i82801gx/Kconfig
source src/southbridge/intel/i82801ix/Kconfig
source src/southbridge/intel/i82870/Kconfig
diff --git a/src/southbridge/intel/Makefile.inc b/src/southbridge/intel/Makefile.inc
index dd20d46..76ea2a4 100644
--- a/src/southbridge/intel/Makefile.inc
+++ b/src/southbridge/intel/Makefile.inc
@@ -6,7 +6,6 @@ subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_I82801AX) += i82801ax
subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_I82801BX) += i82801bx
subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_I82801CX) += i82801cx
subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_I82801DX) += i82801dx
-subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_I82801EX) += i82801ex
subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_I82801GX) += i82801gx
subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_I82801IX) += i82801ix
subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_I82870) += i82870
diff --git a/src/southbridge/intel/i82801ex/Kconfig b/src/southbridge/intel/i82801ex/Kconfig
deleted file mode 100644
index caa5c79..0000000
--- a/src/southbridge/intel/i82801ex/Kconfig
+++ /dev/null
@@ -1,14 +0,0 @@
-config SOUTHBRIDGE_INTEL_I82801EX
- bool
- select SOUTHBRIDGE_INTEL_COMMON
- select IOAPIC
- select HAVE_HARD_RESET
- select HAVE_USBDEBUG
-
-if SOUTHBRIDGE_INTEL_I82801EX
-
-config EHCI_BAR
- hex
- default 0xfef00000
-
-endif
diff --git a/src/southbridge/intel/i82801ex/Makefile.inc b/src/southbridge/intel/i82801ex/Makefile.inc
deleted file mode 100644
index fb76a98..0000000
--- a/src/southbridge/intel/i82801ex/Makefile.inc
+++ /dev/null
@@ -1,11 +0,0 @@
-ramstage-y += i82801ex.c
-ramstage-y += uhci.c
-ramstage-y += lpc.c
-ramstage-y += ide.c
-ramstage-y += sata.c
-ramstage-y += ehci.c
-ramstage-y += smbus.c
-ramstage-y += pci.c
-ramstage-y += ac97.c
-ramstage-y += watchdog.c
-ramstage-y += reset.c
diff --git a/src/southbridge/intel/i82801ex/ac97.c b/src/southbridge/intel/i82801ex/ac97.c
deleted file mode 100644
index 08efe15..0000000
--- a/src/southbridge/intel/i82801ex/ac97.c
+++ /dev/null
@@ -1,37 +0,0 @@
-#include <console/console.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include <device/pci_ops.h>
-#include "i82801ex.h"
-
-static void ac97_set_subsystem(device_t dev, unsigned vendor, unsigned device)
-{
- /* Write the subsystem vendor and device id */
- pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
- ((device & 0xffff) << 16) | (vendor & 0xffff));
-}
-
-static struct pci_operations lops_pci = {
- .set_subsystem = ac97_set_subsystem,
-};
-static struct device_operations ac97_ops = {
- .read_resources = pci_dev_read_resources,
- .set_resources = pci_dev_set_resources,
- .enable_resources = pci_dev_enable_resources,
- .init = 0,
- .scan_bus = 0,
- .enable = i82801ex_enable,
- .ops_pci = &lops_pci,
-};
-
-static const struct pci_driver ac97_audio_driver __pci_driver = {
- .ops = &ac97_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_AC97_AUDIO,
-};
-static const struct pci_driver ac97_modem_driver __pci_driver = {
- .ops = &ac97_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_AC97_MODEM,
-};
diff --git a/src/southbridge/intel/i82801ex/chip.h b/src/southbridge/intel/i82801ex/chip.h
deleted file mode 100644
index 291fcd7..0000000
--- a/src/southbridge/intel/i82801ex/chip.h
+++ /dev/null
@@ -1,34 +0,0 @@
-#ifndef I82801EX_CHIP_H
-#define I82801EX_CHIP_H
-
-struct southbridge_intel_i82801ex_config
-{
-
-#define ICH5R_GPIO_USE_MASK 0x03
-#define ICH5R_GPIO_USE_DEFAULT 0x00
-#define ICH5R_GPIO_USE_AS_NATIVE 0x01
-#define ICH5R_GPIO_USE_AS_GPIO 0x02
-
-#define ICH5R_GPIO_SEL_MASK 0x0c
-#define ICH5R_GPIO_SEL_DEFAULT 0x00
-#define ICH5R_GPIO_SEL_OUTPUT 0x04
-#define ICH5R_GPIO_SEL_INPUT 0x08
-
-#define ICH5R_GPIO_LVL_MASK 0x30
-#define ICH5R_GPIO_LVL_DEFAULT 0x00
-#define ICH5R_GPIO_LVL_LOW 0x10
-#define ICH5R_GPIO_LVL_HIGH 0x20
-#define ICH5R_GPIO_LVL_BLINK 0x30
-
-#define ICH5R_GPIO_INV_MASK 0xc0
-#define ICH5R_GPIO_INV_DEFAULT 0x00
-#define ICH5R_GPIO_INV_OFF 0x40
-#define ICH5R_GPIO_INV_ON 0x80
-
- /* GPIO use select */
- unsigned char gpio[64];
- unsigned int pirq_a_d;
- unsigned int pirq_e_h;
-};
-
-#endif /* I82801EX_CHIP_H */
diff --git a/src/southbridge/intel/i82801ex/early_smbus.c b/src/southbridge/intel/i82801ex/early_smbus.c
deleted file mode 100644
index cdf1f62..0000000
--- a/src/southbridge/intel/i82801ex/early_smbus.c
+++ /dev/null
@@ -1,130 +0,0 @@
-#include "smbus.h"
-
-#define SMBUS_IO_BASE 0x0f00
-
-static void enable_smbus(void)
-{
- device_t dev = PCI_DEV(0x0, 0x1f, 0x3);
-
- print_spew("SMBus controller enabled\n");
-
- pci_write_config32(dev, 0x20, SMBUS_IO_BASE | 1);
- print_debug_hex32(pci_read_config32(dev, 0x20));
- /* Set smbus enable */
- pci_write_config8(dev, 0x40, 1);
- /* Set smbus iospace enable */
- pci_write_config8(dev, 0x4, 1);
- /* SMBALERT_DIS */
- pci_write_config8(dev, 0x11, 4);
-
- /* Disable interrupt generation */
- outb(0, SMBUS_IO_BASE + SMBHSTCTL);
-
- /* clear any lingering errors, so the transaction will run */
- outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
-}
-
-static int smbus_read_byte(unsigned device, unsigned address)
-{
- return do_smbus_read_byte(SMBUS_IO_BASE, device, address);
-}
-
-#ifdef UNUSED_CODE
-static void smbus_write_byte(unsigned device, unsigned address, unsigned char val)
-{
- if (smbus_wait_until_ready(SMBUS_IO_BASE) < 0) {
- return;
- }
-
- print_debug("Unimplemented smbus_write_byte() called.\n");
-
-#if 0
- /* setup transaction */
- /* disable interrupts */
- outw(inw(SMBUS_IO_BASE + SMBGCTL) & ~((1<<10)|(1<<9)|(1<<8)|(1<<4)),
- SMBUS_IO_BASE + SMBGCTL);
- /* set the device I'm talking too */
- outw(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBHSTADDR);
- outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
- /* set up for a byte data write */ /* FIXME */
- outw((inw(SMBUS_IO_BASE + SMBGCTL) & ~7) | (0x1), SMBUS_IO_BASE + SMBGCTL);
- /* clear any lingering errors, so the transaction will run */
- /* Do I need to write the bits to a 1 to clear an error? */
- outw(inw(SMBUS_IO_BASE + SMBGSTATUS), SMBUS_IO_BASE + SMBGSTATUS);
-
- /* clear the data word...*/
- outw(val, SMBUS_IO_BASE + SMBHSTDAT);
-
- /* start the command */
- outw((inw(SMBUS_IO_BASE + SMBGCTL) | (1 << 3)), SMBUS_IO_BASE + SMBGCTL);
-
- /* poll for transaction completion */
- smbus_wait_until_done(SMBUS_IO_BASE);
-#endif
- return;
-}
-
-static int smbus_write_block(unsigned device, unsigned length, unsigned cmd,
- unsigned data1, unsigned data2)
-{
- unsigned char byte;
- unsigned char stat;
- int i;
-
- /* chear the PM timeout flags, SECOND_TO_STS */
- outw(inw(0x0400 + 0x66), 0x0400 + 0x66);
-
- if (smbus_wait_until_ready(SMBUS_IO_BASE) < 0) {
- return -2;
- }
-
- /* setup transaction */
- /* Obtain ownership */
- outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
- for(stat=0;(stat&0x40)==0;) {
- stat = inb(SMBUS_IO_BASE + SMBHSTSTAT);
- }
- /* clear the done bit */
- outb(0x80, SMBUS_IO_BASE + SMBHSTSTAT);
- /* disable interrupts */
- outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & (~1), SMBUS_IO_BASE + SMBHSTCTL);
-
- /* set the device I'm talking too */
- outb(((device & 0x7f) << 1), SMBUS_IO_BASE + SMBXMITADD);
-
- /* set the command address */
- outb(cmd & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
-
- /* set the block length */
- outb(length & 0xFF, SMBUS_IO_BASE + SMBHSTDAT0);
-
- /* try sending out the first byte of data here */
- byte=(data1>>(0))&0x0ff;
- outb(byte,SMBUS_IO_BASE + SMBBLKDAT);
- /* issue a block write command */
- outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xE3) | (0x5 << 2) | 0x40,
- SMBUS_IO_BASE + SMBHSTCTL);
-
- for(i=0;i<length;i++) {
-
- /* poll for transaction completion */
- if (smbus_wait_until_blk_done(SMBUS_IO_BASE) < 0) {
- return -3;
- }
-
- /* load the next byte */
- if(i>3)
- byte=(data2>>(i%4))&0x0ff;
- else
- byte=(data1>>(i))&0x0ff;
- outb(byte,SMBUS_IO_BASE + SMBBLKDAT);
-
- /* clear the done bit */
- outb(inb(SMBUS_IO_BASE + SMBHSTSTAT),
- SMBUS_IO_BASE + SMBHSTSTAT);
- }
-
- print_debug("SMBUS Block complete\n");
- return 0;
-}
-#endif
diff --git a/src/southbridge/intel/i82801ex/ehci.c b/src/southbridge/intel/i82801ex/ehci.c
deleted file mode 100644
index 28164c5..0000000
--- a/src/southbridge/intel/i82801ex/ehci.c
+++ /dev/null
@@ -1,51 +0,0 @@
-#include <console/console.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include <device/pci_ops.h>
-#include <device/pci_ehci.h>
-#include "i82801ex.h"
-
-static void ehci_init(struct device *dev)
-{
- uint32_t cmd;
-
- printk(BIOS_DEBUG, "EHCI: Setting up controller.. ");
- cmd = pci_read_config32(dev, PCI_COMMAND);
- pci_write_config32(dev, PCI_COMMAND,
- cmd | PCI_COMMAND_MASTER);
-
- printk(BIOS_DEBUG, "done.\n");
-}
-
-static void ehci_set_subsystem(device_t dev, unsigned vendor, unsigned device)
-{
- uint8_t access_cntl;
- access_cntl = pci_read_config8(dev, 0x80);
- /* Enable writes to protected registers */
- pci_write_config8(dev, 0x80, access_cntl | 1);
- /* Write the subsystem vendor and device id */
- pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
- ((device & 0xffff) << 16) | (vendor & 0xffff));
- /* Restore protection */
- pci_write_config8(dev, 0x80, access_cntl);
-}
-
-static struct pci_operations lops_pci = {
- .set_subsystem = &ehci_set_subsystem,
-};
-static struct device_operations ehci_ops = {
- .read_resources = pci_ehci_read_resources,
- .set_resources = pci_dev_set_resources,
- .enable_resources = pci_dev_enable_resources,
- .init = ehci_init,
- .scan_bus = 0,
- .enable = i82801ex_enable,
- .ops_pci = &lops_pci,
-};
-
-static const struct pci_driver ehci_driver __pci_driver = {
- .ops = &ehci_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_EHCI,
-};
diff --git a/src/southbridge/intel/i82801ex/i82801ex.c b/src/southbridge/intel/i82801ex/i82801ex.c
deleted file mode 100644
index fc41645..0000000
--- a/src/southbridge/intel/i82801ex/i82801ex.c
+++ /dev/null
@@ -1,48 +0,0 @@
-#include <console/console.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include "i82801ex.h"
-
-void i82801ex_enable(device_t dev)
-{
- device_t lpc_dev;
- unsigned index = 0;
- uint16_t reg_old, reg;
-
- /* See if we are behind the i82801ex pci bridge */
- lpc_dev = dev_find_slot(dev->bus->secondary, PCI_DEVFN(0x1f, 0));
- if((dev->path.pci.devfn &0xf8)== 0xf8) {
- index = dev->path.pci.devfn & 7;
- }
- else if((dev->path.pci.devfn &0xf8)== 0xe8) {
- index = (dev->path.pci.devfn & 7) +8;
- }
- if ((!lpc_dev) || (index >= 16) || ((1<<index)&0x3091)) {
- return;
- }
- if ((lpc_dev->vendor != PCI_VENDOR_ID_INTEL) ||
- (lpc_dev->device != PCI_DEVICE_ID_INTEL_82801ER_LPC)) {
- uint32_t id;
- id = pci_read_config32(lpc_dev, PCI_VENDOR_ID);
- if (id != (PCI_VENDOR_ID_INTEL |
- (PCI_DEVICE_ID_INTEL_82801ER_LPC << 16))) {
- return;
- }
- }
-
- reg = reg_old = pci_read_config16(lpc_dev, 0xf2);
- reg &= ~(1 << index);
- if (!dev->enabled) {
- reg |= (1 << index);
- }
- if (reg != reg_old) {
- pci_write_config16(lpc_dev, 0xf2, reg);
- }
-
-}
-
-struct chip_operations southbridge_intel_i82801ex_ops = {
- CHIP_NAME("Intel ICH5 (82801Ex) Series Southbridge")
- .enable_dev = i82801ex_enable,
-};
diff --git a/src/southbridge/intel/i82801ex/i82801ex.h b/src/southbridge/intel/i82801ex/i82801ex.h
deleted file mode 100644
index 3c7321a..0000000
--- a/src/southbridge/intel/i82801ex/i82801ex.h
+++ /dev/null
@@ -1,22 +0,0 @@
-#ifndef I82801EX_H
-#define I82801EX_H
-
-#include "chip.h"
-
-extern void i82801ex_enable(device_t dev);
-
-#define PCI_DMA_CFG 0x90
-#define SERIRQ_CNTL 0x64
-#define GEN_CNTL 0xd0
-#define GEN_STS 0xd4
-#define RTC_CONF 0xd8
-#define GEN_PMCON_3 0xa4
-
-#define PMBASE 0x40
-#define ACPI_CNTL 0x44
-#define ACPI_EN (1 << 4)
-#define GPIO_BASE 0x58
-#define GPIO_CNTL 0x5C
-#define GPIO_EN (1 << 4)
-
-#endif /* I82801EX_H */
diff --git a/src/southbridge/intel/i82801ex/ide.c b/src/southbridge/intel/i82801ex/ide.c
deleted file mode 100644
index 542c594..0000000
--- a/src/southbridge/intel/i82801ex/ide.c
+++ /dev/null
@@ -1,42 +0,0 @@
-#include <console/console.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include <device/pci_ops.h>
-#include "i82801ex.h"
-
-static void ide_init(struct device *dev)
-{
- /* Enable IDE devices and timmings */
- pci_write_config16(dev, 0x40, 0x0a307); // IDE0
- pci_write_config16(dev, 0x42, 0x0a307); // IDE1
- pci_write_config8(dev, 0x48, 0x05);
- pci_write_config16(dev, 0x4a, 0x0101);
- pci_write_config16(dev, 0x54, 0x5055);
- printk(BIOS_DEBUG, "IDE Enabled\n");
-}
-
-static void i82801ex_ide_set_subsystem(device_t dev, unsigned vendor, unsigned device)
-{
- /* This value is also visible in uchi[0-2] and smbus functions */
- pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
- ((device & 0xffff) << 16) | (vendor & 0xffff));
-}
-
-static struct pci_operations lops_pci = {
- .set_subsystem = i82801ex_ide_set_subsystem,
-};
-static struct device_operations ide_ops = {
- .read_resources = pci_dev_read_resources,
- .set_resources = pci_dev_set_resources,
- .enable_resources = pci_dev_enable_resources,
- .init = ide_init,
- .scan_bus = 0,
- .ops_pci = &lops_pci,
-};
-
-static const struct pci_driver ide_driver __pci_driver = {
- .ops = &ide_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_IDE,
-};
diff --git a/src/southbridge/intel/i82801ex/lpc.c b/src/southbridge/intel/i82801ex/lpc.c
deleted file mode 100644
index 1823e65..0000000
--- a/src/southbridge/intel/i82801ex/lpc.c
+++ /dev/null
@@ -1,381 +0,0 @@
-/*
- * (C) 2004 Linux Networx
- */
-#include <console/console.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include <device/pci_ops.h>
-#include <pc80/mc146818rtc.h>
-#include <pc80/isa-dma.h>
-#include <arch/io.h>
-#include <arch/ioapic.h>
-#include "i82801ex.h"
-
-
-#define NMI_OFF 0
-#define MAINBOARD_POWER_OFF 0
-#define MAINBOARD_POWER_ON 1
-
-#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
-#endif
-
-/**
- * Enable ACPI I/O range.
- *
- * @param dev PCI device with ACPI and PM BAR's
- */
-static void i82801ex_enable_acpi(struct device *dev)
-{
- u8 gpio_cntl;
-
- /* Enable ACPI I/O range decode and ACPI power management. */
- pci_write_config8(dev, ACPI_CNTL, ACPI_EN);
-
- /* Enable the GPIO bar */
- gpio_cntl = pci_read_config8(dev, GPIO_CNTL);
- gpio_cntl |= GPIO_EN;
- pci_write_config8(dev, GPIO_CNTL, gpio_cntl);
-}
-
-/**
- * Set miscellanous static southbridge features.
- *
- * @param dev PCI device with I/O APIC configuration registers
- */
-static void i82801ex_general_cntl(struct device *dev)
-{
- u32 reg32;
-
- reg32 = pci_read_config32(dev, GEN_CNTL);
- reg32 |= (3 << 7); /* IOAPIC enable (APIC_EN) */
- reg32 |= (1 << 1); /* Delayed transaction enable (DTE) */
- pci_write_config32(dev, GEN_CNTL, reg32);
- printk(BIOS_DEBUG, "Southbridge GEN_CNTL 0x%08x\n", reg32);
-
- reg32 = pci_read_config32(dev, GEN_STS);
- reg32 |= (1<<1);
- pci_write_config32(dev, GEN_STS, reg32);
-
-}
-
-#define SERIRQ_CNTL 0x64
-static void i82801ex_enable_serial_irqs(device_t dev)
-{
- /* set packet length and toggle silent mode bit */
- pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(1 << 6)|((21 - 17) << 2)|(0 << 0));
- pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(0 << 6)|((21 - 17) << 2)|(0 << 0));
-}
-
-#define PCI_DMA_CFG 0x90
-static void i82801ex_pci_dma_cfg(device_t dev)
-{
- /* Set PCI DMA CFG to lpc I/F DMA */
- pci_write_config16(dev, PCI_DMA_CFG, 0xfcff);
-}
-
-#define LPC_EN 0xe6
-static void i82801ex_enable_lpc(device_t dev)
-{
- /* lpc i/f enable */
- pci_write_config8(dev, LPC_EN, 0x0d);
-}
-
-typedef struct southbridge_intel_i82801ex_config config_t;
-
-static void set_i82801ex_gpio_use_sel(
- device_t dev, struct resource *res, config_t *config)
-{
- uint32_t gpio_use_sel, gpio_use_sel2;
- int i;
-
- gpio_use_sel = 0x1A003180;
- gpio_use_sel2 = 0x00000007;
- for(i = 0; i < 64; i++) {
- int val;
- switch(config->gpio[i] & ICH5R_GPIO_USE_MASK) {
- case ICH5R_GPIO_USE_AS_NATIVE: val = 0; break;
- case ICH5R_GPIO_USE_AS_GPIO: val = 1; break;
- default:
- continue;
- }
- /* The caller is responsible for not playing with unimplemented bits */
- if (i < 32) {
- gpio_use_sel &= ~( 1 << i);
- gpio_use_sel |= (val << i);
- } else {
- gpio_use_sel2 &= ~( 1 << (i - 32));
- gpio_use_sel2 |= (val << (i - 32));
- }
- }
- outl(gpio_use_sel, res->base + 0x00);
- outl(gpio_use_sel2, res->base + 0x30);
-}
-
-static void set_i82801ex_gpio_direction(
- device_t dev, struct resource *res, config_t *config)
-{
- uint32_t gpio_io_sel, gpio_io_sel2;
- int i;
-
- gpio_io_sel = 0x0000ffff;
- gpio_io_sel2 = 0x00000300;
- for(i = 0; i < 64; i++) {
- int val;
- switch(config->gpio[i] & ICH5R_GPIO_SEL_MASK) {
- case ICH5R_GPIO_SEL_OUTPUT: val = 0; break;
- case ICH5R_GPIO_SEL_INPUT: val = 1; break;
- default:
- continue;
- }
- /* The caller is responsible for not playing with unimplemented bits */
- if (i < 32) {
- gpio_io_sel &= ~( 1 << i);
- gpio_io_sel |= (val << i);
- } else {
- gpio_io_sel2 &= ~( 1 << (i - 32));
- gpio_io_sel2 |= (val << (i - 32));
- }
- }
- outl(gpio_io_sel, res->base + 0x04);
- outl(gpio_io_sel2, res->base + 0x34);
-}
-
-static void set_i82801ex_gpio_level(
- device_t dev, struct resource *res, config_t *config)
-{
- uint32_t gpio_lvl, gpio_lvl2;
- uint32_t gpio_blink;
- int i;
-
- gpio_lvl = 0x1b3f0000;
- gpio_blink = 0x00040000;
- gpio_lvl2 = 0x00030207;
- for(i = 0; i < 64; i++) {
- int val, blink;
- switch(config->gpio[i] & ICH5R_GPIO_LVL_MASK) {
- case ICH5R_GPIO_LVL_LOW: val = 0; blink = 0; break;
- case ICH5R_GPIO_LVL_HIGH: val = 1; blink = 0; break;
- case ICH5R_GPIO_LVL_BLINK: val = 1; blink = 1; break;
- default:
- continue;
- }
- /* The caller is responsible for not playing with unimplemented bits */
- if (i < 32) {
- gpio_lvl &= ~( 1 << i);
- gpio_blink &= ~( 1 << i);
- gpio_lvl |= ( val << i);
- gpio_blink |= (blink << i);
- } else {
- gpio_lvl2 &= ~( 1 << (i - 32));
- gpio_lvl2 |= (val << (i - 32));
- }
- }
- outl(gpio_lvl, res->base + 0x0c);
- outl(gpio_blink, res->base + 0x18);
- outl(gpio_lvl2, res->base + 0x38);
-}
-
-static void set_i82801ex_gpio_inv(
- device_t dev, struct resource *res, config_t *config)
-{
- uint32_t gpio_inv;
- int i;
-
- gpio_inv = 0x00000000;
- for(i = 0; i < 32; i++) {
- int val;
- switch(config->gpio[i] & ICH5R_GPIO_INV_MASK) {
- case ICH5R_GPIO_INV_OFF: val = 0; break;
- case ICH5R_GPIO_INV_ON: val = 1; break;
- default:
- continue;
- }
- gpio_inv &= ~( 1 << i);
- gpio_inv |= (val << i);
- }
- outl(gpio_inv, res->base + 0x2c);
-}
-
-static void i82801ex_pirq_init(device_t dev)
-{
- config_t *config;
-
- /* Get the chip configuration */
- config = dev->chip_info;
-
- if(config->pirq_a_d) {
- pci_write_config32(dev, 0x60, config->pirq_a_d);
- }
- if(config->pirq_e_h) {
- pci_write_config32(dev, 0x68, config->pirq_e_h);
- }
-}
-
-
-static void i82801ex_gpio_init(device_t dev)
-{
- struct resource *res;
- config_t *config;
-
- /* Skip if I don't have any configuration */
- if (!dev->chip_info) {
- return;
- }
- /* The programmer is responsible for ensuring
- * a valid gpio configuration.
- */
-
- /* Get the chip configuration */
- config = dev->chip_info;
- /* Find the GPIO bar */
- res = find_resource(dev, GPIO_BASE);
- if (!res) {
- return;
- }
-
- /* Set the use selects */
- set_i82801ex_gpio_use_sel(dev, res, config);
-
- /* Set the IO direction */
- set_i82801ex_gpio_direction(dev, res, config);
-
- /* Setup the input inverters */
- set_i82801ex_gpio_inv(dev, res, config);
-
- /* Set the value on the GPIO output pins */
- set_i82801ex_gpio_level(dev, res, config);
-
-}
-
-static void enable_hpet(struct device *dev)
-{
- const unsigned long hpet_address = 0xfed00000;
-
- uint32_t dword;
- uint32_t code = (0 & 0x3);
-
- dword = pci_read_config32(dev, GEN_CNTL);
- dword |= (1 << 17); /* enable hpet */
-
- /* Bits [16:15] Memory Address Range
- * 00 FED0_0000h - FED0_03FFh
- * 01 FED0_1000h - FED0_13FFh
- * 10 FED0_2000h - FED0_23FFh
- * 11 FED0_3000h - FED0_33FFh
- */
-
- dword &= ~(3 << 15); /* clear it */
- dword |= (code<<15);
- pci_write_config32(dev, GEN_CNTL, dword);
-
- printk(BIOS_DEBUG, "enabling HPET @0x%lx\n", hpet_address | (code <<12) );
-}
-
-static void lpc_init(struct device *dev)
-{
- uint8_t byte;
- int pwr_on=CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
-
- i82801ex_general_cntl(dev);
-
- /* IO APIC initialization. */
- setup_ioapic(IO_APIC_ADDR, 0); // Don't rename IO APIC ID.
-
- i82801ex_enable_serial_irqs(dev);
-
- i82801ex_pci_dma_cfg(dev);
-
- i82801ex_enable_lpc(dev);
-
- /* Clear SATA to non raid */
- pci_write_config8(dev, 0xae, 0x00);
-
- get_option(&pwr_on, "power_on_after_fail");
- byte = pci_read_config8(dev, 0xa4);
- byte &= 0xfe;
- if (!pwr_on) {
- byte |= 1;
- }
- pci_write_config8(dev, 0xa4, byte);
- printk(BIOS_INFO, "set power %s after power fail\n", pwr_on?"on":"off");
-
- /* Set up the PIRQ */
- i82801ex_pirq_init(dev);
-
- /* Set the state of the gpio lines */
- i82801ex_gpio_init(dev);
-
- /* Initialize the real time clock */
- cmos_init(0);
-
- /* Initialize isa dma */
- isa_dma_init();
-
- /* Disable IDE (needed when sata is enabled) */
- pci_write_config8(dev, 0xf2, 0x60);
-
- enable_hpet(dev);
-}
-
-static void i82801ex_lpc_read_resources(device_t dev)
-{
- struct resource *res;
-
- /* Get the normal PCI resources of this device. */
- pci_dev_read_resources(dev);
-
- /* Add the ACPI BAR */
- res = pci_get_resource(dev, PMBASE);
-
- /* Add the GPIO BAR */
- res = pci_get_resource(dev, GPIO_BASE);
-
- /* Add an extra subtractive resource for both memory and I/O. */
- res = new_resource(dev, IOINDEX_SUBTRACTIVE(0, 0));
- res->base = 0;
- res->size = 0x1000;
- res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE |
- IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
-
- res = new_resource(dev, IOINDEX_SUBTRACTIVE(1, 0));
- res->base = 0xff800000;
- res->size = 0x00800000; /* 8 MB for flash */
- res->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE |
- IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
-
- res = new_resource(dev, 3); /* IOAPIC */
- res->base = IO_APIC_ADDR;
- res->size = 0x00001000;
- res->flags = IORESOURCE_MEM | IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
-}
-
-static void i82801ex_lpc_enable_resources(device_t dev)
-{
- /* Enable the normal PCI resources. */
- pci_dev_enable_resources(dev);
-
- /* Enable ACPI and GPIO BARs. */
- i82801ex_enable_acpi(dev);
-}
-
-static struct pci_operations lops_pci = {
- .set_subsystem = 0,
-};
-
-static struct device_operations lpc_ops = {
- .read_resources = i82801ex_lpc_read_resources,
- .set_resources = pci_dev_set_resources,
- .enable_resources = i82801ex_lpc_enable_resources,
- .init = lpc_init,
- .scan_bus = scan_static_bus,
- .enable = i82801ex_enable,
- .ops_pci = &lops_pci,
-};
-
-static const struct pci_driver lpc_driver __pci_driver = {
- .ops = &lpc_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_LPC,
-};
diff --git a/src/southbridge/intel/i82801ex/pci.c b/src/southbridge/intel/i82801ex/pci.c
deleted file mode 100644
index f1c8183..0000000
--- a/src/southbridge/intel/i82801ex/pci.c
+++ /dev/null
@@ -1,44 +0,0 @@
-#include <console/console.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include <device/pci_ops.h>
-#include "i82801ex.h"
-
-static void pci_init(struct device *dev)
-{
- uint16_t word;
-
- /* Clear system errors */
- word = pci_read_config16(dev, 0x06);
- word |= 0xf900; /* Clear possible errors */
- pci_write_config16(dev, 0x06, word);
-
-#if 0
- /* System error enable */
- uint32_t dword;
- dword = pci_read_config32(dev, 0x04);
- dword |= (1<<8); /* SERR# Enable */
- dword |= (1<<6); /* Parity Error Response */
- pci_write_config32(dev, 0x04, dword);
-#endif
-
- word = pci_read_config16(dev, 0x1e);
- word |= 0xf800; /* Clear possible errors */
- pci_write_config16(dev, 0x1e, word);
-}
-
-static struct device_operations pci_ops = {
- .read_resources = pci_bus_read_resources,
- .set_resources = pci_dev_set_resources,
- .enable_resources = pci_bus_enable_resources,
- .init = pci_init,
- .scan_bus = pci_scan_bridge,
- .ops_pci = 0,
-};
-
-static const struct pci_driver pci_driver __pci_driver = {
- .ops = &pci_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_PCI,
-};
diff --git a/src/southbridge/intel/i82801ex/reset.c b/src/southbridge/intel/i82801ex/reset.c
deleted file mode 100644
index 9936892..0000000
--- a/src/southbridge/intel/i82801ex/reset.c
+++ /dev/null
@@ -1,8 +0,0 @@
-#include <arch/io.h>
-#include <reset.h>
-
-void hard_reset(void)
-{
- /* Try rebooting through port 0xcf9 */
- outb((0 <<3)|(1<<2)|(1<<1), 0xcf9);
-}
diff --git a/src/southbridge/intel/i82801ex/sata.c b/src/southbridge/intel/i82801ex/sata.c
deleted file mode 100644
index b3d8f37..0000000
--- a/src/southbridge/intel/i82801ex/sata.c
+++ /dev/null
@@ -1,59 +0,0 @@
-#include <console/console.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include <device/pci_ops.h>
-#include "i82801ex.h"
-
-static void sata_init(struct device *dev)
-{
- printk(BIOS_DEBUG, "SATA init\n");
- /* SATA configuration */
- pci_write_config8(dev, 0x04, 0x07);
- pci_write_config8(dev, 0x09, 0x8f);
-
- /* Set timmings */
- pci_write_config16(dev, 0x40, 0x0a307);
- pci_write_config16(dev, 0x42, 0x0a307);
-
- /* Sync DMA */
- pci_write_config16(dev, 0x48, 0x000f);
- pci_write_config16(dev, 0x4a, 0x1111);
-
- /* 66 mhz */
- pci_write_config16(dev, 0x54, 0xf00f);
-
- /* Combine ide - sata configuration */
- pci_write_config8(dev, 0x90, 0x0);
-
- /* port 0 & 1 enable */
- pci_write_config8(dev, 0x92, 0x33);
-
- /* initialize SATA */
- pci_write_config16(dev, 0xa0, 0x0018);
- pci_write_config32(dev, 0xa4, 0x00000264);
- pci_write_config16(dev, 0xa0, 0x0040);
- pci_write_config32(dev, 0xa4, 0x00220043);
-
-}
-
-static struct device_operations sata_ops = {
- .read_resources = pci_dev_read_resources,
- .set_resources = pci_dev_set_resources,
- .enable_resources = pci_dev_enable_resources,
- .init = sata_init,
- .scan_bus = 0,
- .ops_pci = 0,
-};
-
-static const struct pci_driver sata_driver __pci_driver = {
- .ops = &sata_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_SATA,
-};
-
-static const struct pci_driver sata_driver_nr __pci_driver = {
- .ops = &sata_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801EB_SATA,
-};
diff --git a/src/southbridge/intel/i82801ex/smbus.c b/src/southbridge/intel/i82801ex/smbus.c
deleted file mode 100644
index fe49e11..0000000
--- a/src/southbridge/intel/i82801ex/smbus.c
+++ /dev/null
@@ -1,48 +0,0 @@
-#include <device/device.h>
-#include <device/path.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include <device/pci_ops.h>
-#include <device/smbus.h>
-#include <arch/io.h>
-#include "i82801ex.h"
-#include "smbus.h"
-
-static int lsmbus_read_byte(device_t dev, u8 address)
-{
- u16 device;
- struct resource *res;
- struct bus *pbus;
-
- device = dev->path.i2c.device;
- pbus = get_pbus_smbus(dev);
- res = find_resource(pbus->dev, 0x20);
-
- return do_smbus_read_byte(res->base, device, address);
-}
-
-static struct smbus_bus_operations lops_smbus_bus = {
- .read_byte = lsmbus_read_byte,
-};
-
-static struct pci_operations lops_pci = {
- /* The subsystem id follows the ide controller */
- .set_subsystem = 0,
-};
-
-static struct device_operations smbus_ops = {
- .read_resources = pci_dev_read_resources,
- .set_resources = pci_dev_set_resources,
- .enable_resources = pci_dev_enable_resources,
- .init = 0,
- .scan_bus = scan_static_bus,
- .enable = i82801ex_enable,
- .ops_pci = &lops_pci,
- .ops_smbus_bus = &lops_smbus_bus,
-};
-
-static const struct pci_driver smbus_driver __pci_driver = {
- .ops = &smbus_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_SMB,
-};
diff --git a/src/southbridge/intel/i82801ex/smbus.h b/src/southbridge/intel/i82801ex/smbus.h
deleted file mode 100644
index b166797..0000000
--- a/src/southbridge/intel/i82801ex/smbus.h
+++ /dev/null
@@ -1,104 +0,0 @@
-#include <device/smbus_def.h>
-
-#define SMBHSTSTAT 0x0
-#define SMBHSTCTL 0x2
-#define SMBHSTCMD 0x3
-#define SMBXMITADD 0x4
-#define SMBHSTDAT0 0x5
-#define SMBHSTDAT1 0x6
-#define SMBBLKDAT 0x7
-#define SMBTRNSADD 0x9
-#define SMBSLVDATA 0xa
-#define SMLINK_PIN_CTL 0xe
-#define SMBUS_PIN_CTL 0xf
-
-#define SMBUS_TIMEOUT (100*1000*10)
-
-
-static void smbus_delay(void)
-{
- outb(0x80, 0x80);
-}
-
-static int smbus_wait_until_ready(unsigned smbus_io_base)
-{
- unsigned loops = SMBUS_TIMEOUT;
- unsigned char byte;
- do {
- smbus_delay();
- if (--loops == 0)
- break;
- byte = inb(smbus_io_base + SMBHSTSTAT);
- } while(byte & 1);
- return loops?0:-1;
-}
-
-static int smbus_wait_until_done(unsigned smbus_io_base)
-{
- unsigned loops = SMBUS_TIMEOUT;
- unsigned char byte;
- do {
- smbus_delay();
- if (--loops == 0)
- break;
- byte = inb(smbus_io_base + SMBHSTSTAT);
- } while((byte & 1) || (byte & ~((1<<6)|(1<<0))) == 0);
- return loops?0:-1;
-}
-
-static inline int smbus_wait_until_blk_done(unsigned smbus_io_base)
-{
- unsigned loops = SMBUS_TIMEOUT;
- unsigned char byte;
- do {
- smbus_delay();
- if (--loops == 0)
- break;
- byte = inb(smbus_io_base + SMBHSTSTAT);
- } while((byte&(1<<7)) == 0);
- return loops?0:-1;
-}
-
-static int do_smbus_read_byte(unsigned smbus_io_base, unsigned device, unsigned address)
-{
- unsigned char global_status_register;
- unsigned char byte;
-
- if (smbus_wait_until_ready(smbus_io_base) < 0) {
- return SMBUS_WAIT_UNTIL_READY_TIMEOUT;
- }
- /* setup transaction */
- /* disable interrupts */
- outb(inb(smbus_io_base + SMBHSTCTL) & (~1), smbus_io_base + SMBHSTCTL);
- /* set the device I'm talking too */
- outb(((device & 0x7f) << 1) | 1, smbus_io_base + SMBXMITADD);
- /* set the command/address... */
- outb(address & 0xFF, smbus_io_base + SMBHSTCMD);
- /* set up for a byte data read */
- outb((inb(smbus_io_base + SMBHSTCTL) & 0xE3) | (0x2 << 2), smbus_io_base + SMBHSTCTL);
- /* clear any lingering errors, so the transaction will run */
- outb(inb(smbus_io_base + SMBHSTSTAT), smbus_io_base + SMBHSTSTAT);
-
- /* clear the data byte...*/
- outb(0, smbus_io_base + SMBHSTDAT0);
-
- /* start the command */
- outb((inb(smbus_io_base + SMBHSTCTL) | 0x40), smbus_io_base + SMBHSTCTL);
-
- /* poll for transaction completion */
- if (smbus_wait_until_done(smbus_io_base) < 0) {
- return SMBUS_WAIT_UNTIL_DONE_TIMEOUT;
- }
-
- global_status_register = inb(smbus_io_base + SMBHSTSTAT);
-
- /* Ignore the In Use Status... */
- global_status_register &= ~(3 << 5);
-
- /* read results of transaction */
- byte = inb(smbus_io_base + SMBHSTDAT0);
- if (global_status_register != (1 << 1)) {
- return SMBUS_ERROR;
- }
- return byte;
-}
diff --git a/src/southbridge/intel/i82801ex/uhci.c b/src/southbridge/intel/i82801ex/uhci.c
deleted file mode 100644
index c9cf82e..0000000
--- a/src/southbridge/intel/i82801ex/uhci.c
+++ /dev/null
@@ -1,55 +0,0 @@
-#include <console/console.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include <device/pci_ops.h>
-#include "i82801ex.h"
-
-static void uhci_init(struct device *dev)
-{
- uint32_t cmd;
-
-#if 1
- printk(BIOS_DEBUG, "UHCI: Setting up controller.. ");
- cmd = pci_read_config32(dev, PCI_COMMAND);
- pci_write_config32(dev, PCI_COMMAND,
- cmd | PCI_COMMAND_MASTER);
-
-
- printk(BIOS_DEBUG, "done.\n");
-#endif
-
-}
-
-static struct pci_operations lops_pci = {
- /* The subsystem id follows the ide controller */
- .set_subsystem = 0,
-};
-
-static struct device_operations uhci_ops = {
- .read_resources = pci_dev_read_resources,
- .set_resources = pci_dev_set_resources,
- .enable_resources = pci_dev_enable_resources,
- .init = uhci_init,
- .scan_bus = 0,
- .enable = i82801ex_enable,
- .ops_pci = &lops_pci,
-};
-
-static const struct pci_driver uhci_driver __pci_driver = {
- .ops = &uhci_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_USB1,
-};
-
-static const struct pci_driver usb2_driver __pci_driver = {
- .ops = &uhci_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_USB2,
-};
-
-static const struct pci_driver usb3_driver __pci_driver = {
- .ops = &uhci_ops,
- .vendor = PCI_VENDOR_ID_INTEL,
- .device = PCI_DEVICE_ID_INTEL_82801ER_USB3,
-};
diff --git a/src/southbridge/intel/i82801ex/watchdog.c b/src/southbridge/intel/i82801ex/watchdog.c
deleted file mode 100644
index 28e1f5e..0000000
--- a/src/southbridge/intel/i82801ex/watchdog.c
+++ /dev/null
@@ -1,28 +0,0 @@
-#include <console/console.h>
-#include <watchdog.h>
-#include <arch/io.h>
-#include <device/device.h>
-#include <device/pci.h>
-
-void watchdog_off(void)
-{
- device_t dev;
- unsigned long value,base;
-
- /* turn off the ICH5 watchdog */
- dev = dev_find_slot(0, PCI_DEVFN(0x1f,0));
- /* Enable I/O space */
- value = pci_read_config16(dev, 0x04);
- value |= (1 << 10);
- pci_write_config16(dev, 0x04, value);
- /* Get TCO base */
- base = (pci_read_config32(dev, 0x40) & 0x0fffe) + 0x60;
- /* Disable the watchdog timer */
- value = inw(base + 0x08);
- value |= 1 << 11;
- outw(value, base + 0x08);
- /* Clear TCO timeout status */
- outw(0x0008, base + 0x04);
- outw(0x0002, base + 0x06);
- printk(BIOS_DEBUG, "Watchdog ICH5 disabled\n");
-}
More information about the coreboot-gerrit
mailing list