[LinuxBIOS] EPIA-M VGA

Mon Nov 7 01:29:53 CET 2005

And the log of failure session is this.
I dont have success one, sorry.

These lines are same as yours?

 > VGA random fixup ...
 > INSTALL REAL-MODE IDT
 > DO THE VGA BIOS
 > found VGA: vid=1106, did=3122
 > rom base, size: fffc0000
 > BAD SIGNATURE 0x8 0x1e
 > biosint: # 0x10, eax 0x4f14 ebx 0x18003 ecx 0x1 edx 0x0
 > biosint: ebp 0x17fa0 esp 0xffa edi 0x0 esi 0x187c8
 > biosint: ip 0xb565 cs 0x0 flags 0x46
 > BIOSINT: Unsupport int #0x10

                         --- Okajima, Jun. Tokyo, Japan.

------------
LinuxBIOS-1.1.8.0Fallback Sun Nov  6 07:39:08 UTC 2005 starting...
 Enabling mainboard devices
 Enabling shadow ram
vt8623 init starting
Detecting Memory
Number of Banks 04
Number of Rows 0d
Priamry DRAM width08
No Columns 0b
MA type e0
Bank 0 (*16 Mb) 20
No Physical Banks 01
Total Memory (*16 Mb) 20
CAS Supported 2.5 3
Cycle time at CL X     (nS)50
Cycle time at CL X-0.5 (nS)60
Cycle time at CL X-1   (nS)00
Starting at CAS 3
We can do CAS 2.5
tRP 3c
tRCD 3c
tRAS 28
Low Bond 00  High Bondcc  Setting DQS delay88vt8623 done
00:06 11 23 31 06 00 30 22 00 00 00 06 00 00 00 00
10:08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30:00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
40:00 18 88 80 82 44 00 00 18 99 88 80 82 44 00 00
50:c8 de cf 88 e0 07 00 00 e0 00 20 20 20 20 00 00
60:02 ff 00 30 62 32 01 20 42 2d 43 58 00 44 00 00
70:82 48 00 01 01 08 50 00 01 00 00 00 00 00 00 02
80:0f 6c 00 00 80 00 00 00 02 00 00 00 00 00 00 00
90:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0:02 c0 20 00 07 02 00 1f 04 00 00 00 2f 02 04 00
b0:00 00 00 00 80 00 00 00 88 00 00 00 00 00 00 00
c0:01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0:00 dd 00 00 00 00 01 00 40 00 00 00 00 00 00 00
f0:00 00 00 00 00 00 12 13 00 00 00 00 00 00 00 00
AGP
 Doing MTRR init.
Copying LinuxBIOram.
Jumping to LinuxBIOS.
LinuxBIOS-1.1.8.0Fallback Sun Nov  6 07:39:08 UTC 2005 booting...
clocks_per_usec: 2572
Enumerating buses...
Finiguration type.
PCI: Using conf_CLUSTER: 0 enabled
PCI: pci_scan_bus for bus 0
PCI: 00:00.0 [1106/3123]d
PCI: 00:01.0 [1106/b091] enabled0a.0
Disabling static device: PCI: 00:0a.1
PCI: 00:0d.0 [1106/3044] enabled
In vt8235_enable 1106 PCI: 00:10.0 [1106/3038] enabled0.1 [1106/3038] enabled
In vt8235_enable 1106 3038.
PCI: 00:10.2 [1106/3038] enabled
In vt8235_enable 1106 3104.
PCI: 00:10.3 [1106/3104] enabledIn vt8235_enable 1106 3177.
InitialisinPCI: 00:11.0 [1106/3177] enabled
In vt8235_enable 1106 0571.
PCI: 00:11.1 [1106/0571] enabledCI: 00:11.5 [1106/3059] enabled
In vt8235_enable ffff ffff.
In vt8235_enable 1106 3065.
PCI: 00:12.0 [1106/3065] enabled
PCI: pci_scan_bus for bus 1
PCI: 01:00.0 [1106/3122] enabled
PCI: pci_scan_bus returning with max=01
vt1211 enabld
vt1211 enabling PNP devices.
PNP: 002e.1 enabled
vt1211 enabling PNP devices.
PNP: 002e.2 enabled
vt1211 enabling PNP devices.
PNP: 002e.3 enabled
vt1211 enabling PNPled
PCI: pci_scan_bus returning with max=01
done
Allocating resources...
Reading resources...
Done reading resources.
Setting resources...
I would set ram size to 0x80000 Kbytes
0x00febfe000 - 0x00febfe7ff] mem
PCI: 00:0d.0 14 <- [0x0000001800 - 0x000000187f] io
PCI: 00:10.0 20 <- [0x0000001880 - 0x000000189f] io
PCI: 00:10.1 20 <- [0x00000018a0 - 0x00000018bf] io
PCI: 00:10.2 20 <- [0x00000018c0 - 0x00000018df] io
PCI: 00:10.3 10 <- [0x00febff000 - 0x00febff0ff] mem
PN[0x00000003f0 - 0x00000003f7] io
PNP: 002e.0 70 <- [0x0000000006 - 0x0000000006] irq
PNP: 002e.0 74 <- [0x0000000002 - 0x0000000002] drq
PNP: 002e.1 60 <- [0x0000000378 - 0x000000037f] io
PNP: 002e.1 70 <- [0x0000000007 - 0x0000000007] irq
PNP: 002e.1 74 <- [0x0000000003 - 0x0000000003] drq
PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] io
PNP: 002e.2 70 <- [0x000000000P: 002e.3 60 <- [0x00000002f8 - 0x00000002ff] io
PNP: 002e.3 70 <- [0x0000000003 - 0x0000000003] irq
PNP: 002e.b 60 <- [0x000000ec00 - 0x000000ecff] io
PCI: 00:11.1 20 <- [0x00000018e0 - 0x00000018ef] io
PCI: 00:11.5 10 <- [0x0000001000 - 0x00000010ff] io
PCI: 00:12.0 10 <- [0x0000001400 - 0x00000014ff] io
PCI: 00:12.000 - 0x00fec000ff] mem
Done setting resources.
Done allocating resources.
Enabling resourcess...
PCI: 00:00.0 cmd <- 146
PCI: 00:01.0 bridge ctrl <- 000f
PCI: 00:01.0 cmd <- 147
PCI: 01:00.0 cmd <- 140
PCI: 00:0d.0 cmd <- 1c3
PCI: 00:10.0 subsystem <- 00/00
PCI: 00:10.0 cmd <- 141
PCI: 00:10.1 subsystem <- 00/00
PCI: 00:10.1 cmd <- 141
P
PCI: 00:10.2 cmd <- 141
PCI: 00:10.3 subsystem <- 00/00
PCI: 00:10.3 cmd <- 142
PCI: 00:11.0 cmd <- 147
PNP: 002e.0 - enabling
PNP: 002e.1 - enabling
PNP: 002e.2 - enabling
PNP: 002e.3 - enabling
PNP: 002e.b - enabling
PCI: 00:11.1 cmd <- 147
PCI: 00:11.5 subsystem <- 00/00
PCI: 00:11.5 cmd141
PCI: 00:12.0 cmd <-
                   Initializing devices...
Root Dee init
PCI: 00:10.0 init
PCI: 00:10.1 init
PCI: 00:10.2 init
PCI: 00:10.3 init
PCI: 00:11.0 init
vt8235 init
RTC Init
RTC: Checksum invalid zeroing cmos
Invalid CMOS LB checksum
pci_routing_fixup: dev is 00010ac0
setting firewire
Assigning IRQ 9 to 0:d.0
  Readback = 9
setting usb
Assigning IRQ 5 to 0:10.0
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
Assigning IRQ 9 to 0:10.1
  Readback = 9
ning IRQ 9 to 0:10.2 order bits are wrong: want 0x0, got 0x20
  Readback 9
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
Assigning IRQ 5 to 0:10.3
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
setting vt8235
Assigning IRQ 5 to 0:11.1
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
Assigning IRQ 9 to 0:11.5
  Readback = 9
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
setting ethernet
Assigning IRQ 5 to 0:12.0
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
setting vga
Assigning IRQ 5 to 1:0.0
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
setting pci slot
g cardbus slot
setting riser slot
PNP: 002e.0 init
PNP: 002e.1 init
PNP: 002e.2PNP: 002e.3 init
PNP: 002e.b init
PCI: 00:11.1 init
Enabling VIA IDE.
ide_init: enabling compatibility IDE addresses
enables in reg 0x42 0x0
enables in reg 0x42 read back as 0x0
enables in reg 0x40 0x13
enables in reg 0x40 read back as 0x13
enables in reg 0x9 0x8a
enables in reg 0x9 read back as 0x8a
command in reg 0x4 0x7
command in reg 0x4 reads back as 0x7
PCI: 00:11.5 init
PCI: 00:12.0 init
Configuring VIA Rhine LAN
APIC_CLUSTER: 0 init
Initializing CPU #0
CPU: vendor Centaur device 698
Enabling cache

Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB
Setting fixed MTRRs(24-88) Type: WB
DONE fixed MTRRs
Setting variable MTRR 0, base:    0MB, range:  256MB, type WB
Setting variable MTRR 1, base:  256MB, range:  128MB, type WB
Setting variable MTRR 2, base:   range:   64MB, type WB
Setting variable MTRR 3, base:  448MB, range:   32MB, type WB
DONE varie extra MTRR's

MTRR check
Fixed MTRRs   : Enabled
Variable MTRRs: Enabled

Disabling local apic...done.
CPU #0 Initialized
PCI: 00:00.0 init
VT8623 random fixup ...
Frame buffer at d0000000
PCI: 00:01.0 init
VT8623 AGP random fixup ...
PCI: 00:0d.0 init
PCI: 01:00.0 init
VGA random fixup ...
INSTALL REAL-MODE IDT
DO THE VGA BIOS
found VGA: vid=1106, did=3122
rom base, size: fffc0000
BAD SIGNATURE 0x8 0x1e
biosint: # 0x10, eax 0x4f14 ebx 0x18003 ecx 0x1 edx 0x0
biosint: ebp 0x17fa0 esp 0xffa edi 0x0 esi 0x187c8
biosint: ip 0xb565 cs 0x0 flags 0x46
BIOSINT: Unsupport int #0x10
Devices initialized
Copying IRQ routing tables to 0xf0000...done.
Verifing copy of IRQ routing tables at 0xf0000...done
Checking IRQ routing table consistency...
check_pirq_routing_table() - irq_routing_table located at: 0x000f0000
done.
ACPI: Writing ACPI tables at f0400...
ACPI:     * FACS
ACPI:     * DSDT @ 000f04aa Length 3f0
ACPI:     * FADT
ACPI: added table 1/8 Length now 40
ACPI: done.
Moving GDT to 0x500...ok
Wrote linuxbile at: 00000530 - 00000b60  checksum 828

Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3

    33:stream_ini - 0xfffeffff
Found ELF candiate at offset 0
New segment addr 0x100000 size 0x25390 offset 0xa0 filesize 0xb2e0
(cleaned up) New segment addr 0x100000 size 0x25390 offset 0xa0 filesize 0xb2e0
New segment addr 0x1253a0 size 0x60 offset 0xb380 filesize 0x60
(cleaned up) New segment addr 0x1253a0 size 0x60 offset 0xb380 filesize 0x60
Dropping non PT_LOAD segment
Loading Segment: addr: 0x0000000000100000 memsz: 0x0000000000025390 filesz: 0x000000000000b2e0
Clearing Segment: addr: 0x000000000010b2e0 memsz: 0x000000000001oading Segment: addr: 
0x00000000001253a0 memsz: 0x0000000000000060 filesz: 0x0000000000000060
Jumping to boot code at 0x108b4c
FILO version 0.4.2 (okajima at Debian) Sun Nov  6 04:49:41 UTC 2005Press <Enter> for default boot, or 
<Esc> for boot prompt... timed out
boot: hda1:/vmlinuz root=/dev/he=ttyS0,115200
IDE time out
Netected on IDE channel 0
boot: hda1:/vmlinuz root=/dev/hda1 console=tty0 console=ttyS0,115200