[LinuxBIOS] r2487 - in trunk/LinuxBIOSv2/src/superio/ite: it8661f it8671f it8673f it8705f it8712f it8716f it8718f
svn at openbios.org
svn at openbios.org
Sun Nov 5 00:19:05 CET 2006
Author: uwe
Date: 2006-11-05 00:19:00 +0100 (Sun, 05 Nov 2006)
New Revision: 2487
Modified:
trunk/LinuxBIOSv2/src/superio/ite/it8661f/Config.lb
trunk/LinuxBIOSv2/src/superio/ite/it8661f/chip.h
trunk/LinuxBIOSv2/src/superio/ite/it8661f/it8661f.h
trunk/LinuxBIOSv2/src/superio/ite/it8661f/it8661f_early_serial.c
trunk/LinuxBIOSv2/src/superio/ite/it8671f/Config.lb
trunk/LinuxBIOSv2/src/superio/ite/it8671f/it8671f_early_serial.c
trunk/LinuxBIOSv2/src/superio/ite/it8673f/Config.lb
trunk/LinuxBIOSv2/src/superio/ite/it8673f/it8673f.h
trunk/LinuxBIOSv2/src/superio/ite/it8673f/it8673f_early_serial.c
trunk/LinuxBIOSv2/src/superio/ite/it8705f/Config.lb
trunk/LinuxBIOSv2/src/superio/ite/it8705f/it8705f.h
trunk/LinuxBIOSv2/src/superio/ite/it8705f/it8705f_early_serial.c
trunk/LinuxBIOSv2/src/superio/ite/it8712f/Config.lb
trunk/LinuxBIOSv2/src/superio/ite/it8712f/it8712f.h
trunk/LinuxBIOSv2/src/superio/ite/it8712f/it8712f_early_serial.c
trunk/LinuxBIOSv2/src/superio/ite/it8716f/Config.lb
trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f.h
trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f_early_serial.c
trunk/LinuxBIOSv2/src/superio/ite/it8718f/Config.lb
trunk/LinuxBIOSv2/src/superio/ite/it8718f/it8718f.h
trunk/LinuxBIOSv2/src/superio/ite/it8718f/it8718f_early_serial.c
Log:
Various minor cosmetic changes in the ITE Super I/Os, mostly whitespace
changes and fixing of comments.
Signed-off-by: Uwe Hermann <uwe at hermann-uwe.de>
Acked-by: Uwe Hermann <uwe at hermann-uwe.de>
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8661f/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8661f/Config.lb 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8661f/Config.lb 2006-11-04 23:19:00 UTC (rev 2487)
@@ -20,3 +20,4 @@
config chip.h
object superio.o
+
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8661f/chip.h
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8661f/chip.h 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8661f/chip.h 2006-11-04 23:19:00 UTC (rev 2487)
@@ -23,14 +23,12 @@
/* This chip doesn't seem to have keyboard and mouse support. */
-/* #include <pc80/keyboard.h> */
#include <uart8250.h>
extern struct chip_operations superio_ite_it8661f_ops;
struct superio_ite_it8661f_config {
struct uart8250 com1, com2;
- /* struct pc_keyboard keyboard; */
};
#endif /* _SUPERIO_ITE_IT8661F */
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8661f/it8661f.h
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8661f/it8661f.h 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8661f/it8661f.h 2006-11-04 23:19:00 UTC (rev 2487)
@@ -19,7 +19,7 @@
*/
/* Datasheet: http://www.ite.com.tw/product_info/PC/Brief-IT8661_2.asp */
-/* Status: untested on real hardware, but it compiles. */
+/* Status: Untested on real hardware, but it compiles. */
/* This chip doesn't seem to have keyboard and mouse support. */
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8661f/it8661f_early_serial.c
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8661f/it8661f_early_serial.c 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8661f/it8661f_early_serial.c 2006-11-04 23:19:00 UTC (rev 2487)
@@ -26,7 +26,7 @@
#define SIO_INDEX SIO_BASE
#define SIO_DATA SIO_BASE+1
-/* Global Configuration Registers. */
+/* Global configuration registers. */
#define IT8661F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8661F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8661F_CONFIG_REG_LDE 0x23 /* PnP Logical Device Enable. */
@@ -35,7 +35,7 @@
#define IT8661F_CONFIGURATION_PORT 0x0279 /* Write-only. */
/* Special values used for entering MB PnP mode. The first four bytes of
- * each line determine the address port, the last four are data. */
+ each line determine the address port, the last four are data. */
static const uint8_t init_values[] = {
0x6a, 0xb5, 0xda, 0xed, /**/ 0xf6, 0xfb, 0x7d, 0xbe,
0xdf, 0x6f, 0x37, 0x1b, /**/ 0x0d, 0x86, 0xc3, 0x61,
@@ -44,7 +44,7 @@
};
/* The content of IT8661F_CONFIG_REG_LDN (index 0x07) must be set to the
- * LDN the register belongs to, before you can access the register. */
+ LDN the register belongs to, before you can access the register. */
static void it8661f_sio_write(uint8_t ldn, uint8_t index, uint8_t value)
{
outb(IT8661F_CONFIG_REG_LDN, SIO_BASE);
@@ -53,7 +53,7 @@
outb(value, SIO_DATA);
}
-/* Enable the peripheral devices on the IT8661F Super IO chip. */
+/* Enable the peripheral devices on the IT8661F Super I/O chip. */
static void it8661f_enable_serial(device_t dev, unsigned iobase)
{
uint8_t i;
@@ -88,10 +88,10 @@
it8661f_sio_write(IT8661F_IR, 0x30, 0x1); /* IR */
/* Select 24MHz CLKIN (clear bit 1) and clear software suspend mode
- (clear bit 0). */
+ (clear bit 0). */
it8661f_sio_write(0x00, IT8661F_CONFIG_REG_SWSUSP, 0x00);
/* (3) Exit the configuration state (MB PnP mode). */
- it8661f_sio_write(0x00, IT8661F_CONFIG_REG_CC, 0x02);
+ it8661f_sio_write(0x00, IT8661F_CONFIG_REG_CC, 0x02);
}
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8671f/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8671f/Config.lb 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8671f/Config.lb 2006-11-04 23:19:00 UTC (rev 2487)
@@ -20,3 +20,4 @@
config chip.h
object superio.o
+
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8671f/it8671f_early_serial.c
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8671f/it8671f_early_serial.c 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8671f/it8671f_early_serial.c 2006-11-04 23:19:00 UTC (rev 2487)
@@ -26,7 +26,7 @@
#define SIO_INDEX SIO_BASE
#define SIO_DATA SIO_BASE+1
-/* Global Configuration Registers. */
+/* Global configuration registers. */
#define IT8671F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8671F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8671F_CONFIG_REG_LDE 0x23 /* PnP Logical Device Enable. */
@@ -35,7 +35,7 @@
#define IT8671F_CONFIGURATION_PORT 0x0279 /* Write-only. */
/* Special values used for entering MB PnP mode. The first four bytes of
- * each line determine the address port, the last four are data. */
+ each line determine the address port, the last four are data. */
static const uint8_t init_values[] = {
0x6a, 0xb5, 0xda, 0xed, /**/ 0xf6, 0xfb, 0x7d, 0xbe,
0xdf, 0x6f, 0x37, 0x1b, /**/ 0x0d, 0x86, 0xc3, 0x61,
@@ -44,7 +44,7 @@
};
/* The content of IT8671F_CONFIG_REG_LDN (index 0x07) must be set to the
- * LDN the register belongs to, before you can access the register. */
+ LDN the register belongs to, before you can access the register. */
static void it8671f_sio_write(uint8_t ldn, uint8_t index, uint8_t value)
{
outb(IT8671F_CONFIG_REG_LDN, SIO_BASE);
@@ -53,7 +53,7 @@
outb(value, SIO_DATA);
}
-/* Enable the peripheral devices on the IT8671F Super IO chip. */
+/* Enable the peripheral devices on the IT8671F Super I/O chip. */
static void it8671f_enable_serial(device_t dev, unsigned iobase)
{
uint8_t i;
@@ -80,7 +80,7 @@
PP (3), Reserved (4), KBCK (5), KBCM (6), Reserved (7). */
it8671f_sio_write(0x00, IT8671F_CONFIG_REG_LDE, 0x6f);
- /* Activate all devices. */
+ /* Activate all devices. */
it8671f_sio_write(IT8671F_FDC, 0x30, 0x01); /* Floppy */
it8671f_sio_write(IT8671F_SP1, 0x30, 0x01); /* Serial port 1 */
it8671f_sio_write(IT8671F_SP2, 0x30, 0x01); /* Serial port 2 */
@@ -93,6 +93,6 @@
it8671f_sio_write(0x00, IT8671F_CONFIG_REG_SWSUSP, 0x00);
/* (3) Exit the configuration state (MB PnP mode). */
- it8671f_sio_write(0x00, IT8671F_CONFIG_REG_CC, 0x02);
+ it8671f_sio_write(0x00, IT8671F_CONFIG_REG_CC, 0x02);
}
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8673f/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8673f/Config.lb 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8673f/Config.lb 2006-11-04 23:19:00 UTC (rev 2487)
@@ -20,3 +20,4 @@
config chip.h
object superio.o
+
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8673f/it8673f.h
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8673f/it8673f.h 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8673f/it8673f.h 2006-11-04 23:19:00 UTC (rev 2487)
@@ -19,7 +19,7 @@
*/
/* Datasheet: http://www.datasheet4u.com/html/I/T/8/IT8673F_ITE.pdf.html */
-/* Status: untested on real hardware, but it compiles. */
+/* Status: Untested on real hardware, but it compiles. */
#define IT8673F_FDC 0x00 /* Floppy */
#define IT8673F_SP1 0x01 /* Com1 */
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8673f/it8673f_early_serial.c
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8673f/it8673f_early_serial.c 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8673f/it8673f_early_serial.c 2006-11-04 23:19:00 UTC (rev 2487)
@@ -26,7 +26,7 @@
#define SIO_INDEX SIO_BASE
#define SIO_DATA SIO_BASE+1
-/* Global Configuration Registers. */
+/* Global configuration registers. */
#define IT8673F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8673F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8673F_CONFIG_REG_CLOCKSEL 0x23 /* Clock Selection. */
@@ -35,7 +35,7 @@
#define IT8673F_CONFIGURATION_PORT 0x0279 /* Write-only. */
/* Special values used for entering MB PnP mode. The first four bytes of
- * each line determine the address port, the last four are data. */
+ each line determine the address port, the last four are data. */
static const uint8_t init_values[] = {
0x6a, 0xb5, 0xda, 0xed, /**/ 0xf6, 0xfb, 0x7d, 0xbe,
0xdf, 0x6f, 0x37, 0x1b, /**/ 0x0d, 0x86, 0xc3, 0x61,
@@ -44,7 +44,7 @@
};
/* The content of IT8673F_CONFIG_REG_LDN (index 0x07) must be set to the
- * LDN the register belongs to, before you can access the register. */
+ LDN the register belongs to, before you can access the register. */
static void it8673f_sio_write(uint8_t ldn, uint8_t index, uint8_t value)
{
outb(IT8673F_CONFIG_REG_LDN, SIO_BASE);
@@ -53,7 +53,7 @@
outb(value, SIO_DATA);
}
-/* Enable the peripheral devices on the IT8673F Super IO chip. */
+/* Enable the peripheral devices on the IT8673F Super I/O chip. */
static void it8673f_enable_serial(device_t dev, unsigned iobase)
{
uint8_t i;
@@ -92,6 +92,6 @@
it8673f_sio_write(0x00, IT8673F_CONFIG_REG_SWSUSP, 0x00);
/* (3) Exit the configuration state (MB PnP mode). */
- it8673f_sio_write(0x00, IT8673F_CONFIG_REG_CC, 0x02);
+ it8673f_sio_write(0x00, IT8673F_CONFIG_REG_CC, 0x02);
}
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8705f/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8705f/Config.lb 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8705f/Config.lb 2006-11-04 23:19:00 UTC (rev 2487)
@@ -20,3 +20,4 @@
config chip.h
object superio.o
+
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8705f/it8705f.h
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8705f/it8705f.h 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8705f/it8705f.h 2006-11-04 23:19:00 UTC (rev 2487)
@@ -19,7 +19,7 @@
*/
/* Datasheet: http://www.ite.com.tw/product_info/PC/Brief-IT8705_2.asp */
-/* Status: untested on real hardware, but it compiles. */
+/* Status: Untested on real hardware, but it compiles. */
/* Note: This should also work on an IT8705AF, they're almost the same. */
/* This chip doesn't seem to have keyboard and mouse support. */
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8705f/it8705f_early_serial.c
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8705f/it8705f_early_serial.c 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8705f/it8705f_early_serial.c 2006-11-04 23:19:00 UTC (rev 2487)
@@ -26,19 +26,19 @@
#define SIO_INDEX SIO_BASE
#define SIO_DATA SIO_BASE+1
-/* Global Configuration Registers. */
+/* Global configuration registers. */
#define IT8705F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8705F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8705F_CONFIG_REG_CONFIGSEL 0x22 /* Configuration Select. */
/* WTF? 0x23 and 0x24 are swapped here (when compared to other IT87xx). */
-#define IT8705F_CONFIG_REG_CLOCKSEL 0x24 /* Clock Selection. */
-#define IT8705F_CONFIG_REG_SWSUSP 0x23 /* Software Suspend, Flash I/F. */
+#define IT8705F_CONFIG_REG_CLOCKSEL 0x24 /* Clock Selection, Flash I/F. */
+#define IT8705F_CONFIG_REG_SWSUSP 0x23 /* Software Suspend. */
#define IT8705F_CONFIGURATION_PORT 0x2e /* Write-only. */
/* The content of IT8705F_CONFIG_REG_LDN (index 0x07) must be set to the
- * LDN the register belongs to, before you can access the register. */
+ LDN the register belongs to, before you can access the register. */
static void it8705f_sio_write(uint8_t ldn, uint8_t index, uint8_t value)
{
outb(IT8705F_CONFIG_REG_LDN, SIO_BASE);
@@ -47,7 +47,7 @@
outb(value, SIO_DATA);
}
-/* Enable the peripheral devices on the IT8705F Super IO chip. */
+/* Enable the peripheral devices on the IT8705F Super I/O chip. */
static void it8705f_enable_serial(device_t dev, unsigned iobase)
{
/* (1) Enter the configuration state (MB PnP mode). */
@@ -63,8 +63,8 @@
/* (2) Modify the data of configuration registers. */
/* Select the chip to configure (if there's more than one).
- * Set bit 7 to select JP3=1, clear bit 7 to select JP3=0.
- * If this register is not written, both chips are configured. */
+ Set bit 7 to select JP3=1, clear bit 7 to select JP3=0.
+ If this register is not written, both chips are configured. */
/* it8705f_sio_write(0x00, IT8705F_CONFIG_REG_CONFIGSEL, 0x00); */
/* Enable all devices. */
@@ -73,18 +73,17 @@
it8705f_sio_write(IT8705F_SP2, 0x30, 0x1); /* Serial port 2 */
it8705f_sio_write(IT8705F_PP, 0x30, 0x1); /* Parallel port */
it8705f_sio_write(IT8705F_EC, 0x30, 0x1); /* Environment controller */
- /* GPIO */
it8705f_sio_write(IT8705F_GAME, 0x30, 0x1); /* GAME port */
it8705f_sio_write(IT8705F_IR, 0x30, 0x1); /* Consumer IR */
it8705f_sio_write(IT8705F_MIDI, 0x30, 0x1); /* MIDI port */
/* Select 24MHz/48MHz CLKIN (set/clear bit 0). TODO: Needed? */
- /* it8705f_sio_write(0x00, IT8705F_CONFIG_REG_CLOCKSEL, 0x00); */
+ /* it8705f_sio_write(0x00, IT8705F_CONFIG_REG_CLOCKSEL, 0x01); */
/* Clear software suspend mode (clear bit 0). TODO: Needed? */
/* it8705f_sio_write(0x00, IT8705F_CONFIG_REG_SWSUSP, 0x00); */
/* (3) Exit the configuration state (MB PnP mode). */
- it8705f_sio_write(0x00, IT8705F_CONFIG_REG_CC, 0x02);
+ it8705f_sio_write(0x00, IT8705F_CONFIG_REG_CC, 0x02);
}
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8712f/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8712f/Config.lb 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8712f/Config.lb 2006-11-04 23:19:00 UTC (rev 2487)
@@ -20,3 +20,4 @@
config chip.h
object superio.o
+
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8712f/it8712f.h
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8712f/it8712f.h 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8712f/it8712f.h 2006-11-04 23:19:00 UTC (rev 2487)
@@ -19,7 +19,7 @@
*/
/* Datasheet: http://www.ite.com.tw/product_info/PC/Brief-IT8712_2.asp */
-/* Status: untested on real hardware, but it compiles. */
+/* Status: Untested on real hardware, but it compiles. */
#define IT8712F_FDC 0x00 /* Floppy */
#define IT8712F_SP1 0x01 /* Com1 */
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8712f/it8712f_early_serial.c
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8712f/it8712f_early_serial.c 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8712f/it8712f_early_serial.c 2006-11-04 23:19:00 UTC (rev 2487)
@@ -26,7 +26,7 @@
#define SIO_INDEX SIO_BASE
#define SIO_DATA SIO_BASE+1
-/* Global Configuration Registers. */
+/* Global configuration registers. */
#define IT8712F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8712F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8712F_CONFIG_REG_CONFIGSEL 0x22 /* Configuration Select. */
@@ -36,7 +36,7 @@
#define IT8712F_CONFIGURATION_PORT 0x2e /* Write-only. */
/* The content of IT8712F_CONFIG_REG_LDN (index 0x07) must be set to the
- * LDN the register belongs to, before you can access the register. */
+ LDN the register belongs to, before you can access the register. */
static void it8712f_sio_write(uint8_t ldn, uint8_t index, uint8_t value)
{
outb(IT8712F_CONFIG_REG_LDN, SIO_BASE);
@@ -45,7 +45,7 @@
outb(value, SIO_DATA);
}
-/* Enable the peripheral devices on the IT8712F Super IO chip. */
+/* Enable the peripheral devices on the IT8712F Super I/O chip. */
static void it8712f_enable_serial(device_t dev, unsigned iobase)
{
/* (1) Enter the configuration state (MB PnP mode). */
@@ -61,8 +61,8 @@
/* (2) Modify the data of configuration registers. */
/* Select the chip to configure (if there's more than one).
- * Set bit 7 to select JP3=1, clear bit 7 to select JP3=0.
- * If this register is not written, both chips are configured. */
+ Set bit 7 to select JP3=1, clear bit 7 to select JP3=0.
+ If this register is not written, both chips are configured. */
/* it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CONFIGSEL, 0x00); */
/* Enable all devices. */
@@ -78,12 +78,12 @@
it8712f_sio_write(IT8712F_IR, 0x30, 0x1); /* Consumer IR */
/* Select 24MHz/48MHz CLKIN (set/clear bit 0). TODO: Needed? */
- /* it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CLOCKSEL, 0x00); */
+ /* it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CLOCKSEL, 0x01); */
/* Clear software suspend mode (clear bit 0). TODO: Needed? */
/* it8712f_sio_write(0x00, IT8712F_CONFIG_REG_SWSUSP, 0x00); */
/* (3) Exit the configuration state (MB PnP mode). */
- it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CC, 0x02);
+ it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CC, 0x02);
}
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8716f/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8716f/Config.lb 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8716f/Config.lb 2006-11-04 23:19:00 UTC (rev 2487)
@@ -20,3 +20,4 @@
config chip.h
object superio.o
+
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f.h
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f.h 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f.h 2006-11-04 23:19:00 UTC (rev 2487)
@@ -19,7 +19,7 @@
*/
/* Datasheet: http://www.ite.com.tw/product_info/PC/Brief-IT8716_2.asp */
-/* Status: untested on real hardware, but it compiles. */
+/* Status: Untested on real hardware, but it compiles. */
#define IT8716F_FDC 0x00 /* Floppy */
#define IT8716F_SP1 0x01 /* Com1 */
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f_early_serial.c
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f_early_serial.c 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f_early_serial.c 2006-11-04 23:19:00 UTC (rev 2487)
@@ -26,7 +26,7 @@
#define SIO_INDEX SIO_BASE
#define SIO_DATA SIO_BASE+1
-/* Global Configuration Registers. */
+/* Global configuration registers. */
#define IT8716F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8716F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8716F_CONFIG_REG_CONFIGSEL 0x22 /* Configuration Select. */
@@ -36,7 +36,7 @@
#define IT8716F_CONFIGURATION_PORT 0x2e /* Write-only. */
/* The content of IT8716F_CONFIG_REG_LDN (index 0x07) must be set to the
- * LDN the register belongs to, before you can access the register. */
+ LDN the register belongs to, before you can access the register. */
static void it8716f_sio_write(uint8_t ldn, uint8_t index, uint8_t value)
{
outb(IT8716F_CONFIG_REG_LDN, SIO_BASE);
@@ -45,7 +45,7 @@
outb(value, SIO_DATA);
}
-/* Enable the peripheral devices on the IT8716F Super IO chip. */
+/* Enable the peripheral devices on the IT8716F Super I/O chip. */
static void it8716f_enable_serial(device_t dev, unsigned iobase)
{
/* (1) Enter the configuration state (MB PnP mode). */
@@ -61,8 +61,8 @@
/* (2) Modify the data of configuration registers. */
/* Select the chip to configure (if there's more than one).
- * Set bit 7 to select JP3=1, clear bit 7 to select JP3=0.
- * If this register is not written, both chips are configured. */
+ Set bit 7 to select JP3=1, clear bit 7 to select JP3=0.
+ If this register is not written, both chips are configured. */
/* it8716f_sio_write(0x00, IT8716F_CONFIG_REG_CONFIGSEL, 0x00); */
/* Enable all devices. */
@@ -78,12 +78,12 @@
it8716f_sio_write(IT8716F_IR, 0x30, 0x1); /* Consumer IR */
/* Select 24MHz/48MHz CLKIN (set/clear bit 0). TODO: Needed? */
- /* it8716f_sio_write(0x00, IT8716F_CONFIG_REG_CLOCKSEL, 0x00); */
+ /* it8716f_sio_write(0x00, IT8716F_CONFIG_REG_CLOCKSEL, 0x01); */
/* Clear software suspend mode (clear bit 0). TODO: Needed? */
/* it8716f_sio_write(0x00, IT8716F_CONFIG_REG_SWSUSP, 0x00); */
/* (3) Exit the configuration state (MB PnP mode). */
- it8716f_sio_write(0x00, IT8716F_CONFIG_REG_CC, 0x02);
+ it8716f_sio_write(0x00, IT8716F_CONFIG_REG_CC, 0x02);
}
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8718f/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8718f/Config.lb 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8718f/Config.lb 2006-11-04 23:19:00 UTC (rev 2487)
@@ -20,3 +20,4 @@
config chip.h
object superio.o
+
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8718f/it8718f.h
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8718f/it8718f.h 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8718f/it8718f.h 2006-11-04 23:19:00 UTC (rev 2487)
@@ -19,7 +19,7 @@
*/
/* Datasheet: http://www.ite.com.tw/product_info/PC/Brief-IT8718_2.asp */
-/* Status: untested on real hardware, but it compiles. */
+/* Status: Untested on real hardware, but it compiles. */
#define IT8718F_FDC 0x00 /* Floppy */
#define IT8718F_SP1 0x01 /* Com1 */
Modified: trunk/LinuxBIOSv2/src/superio/ite/it8718f/it8718f_early_serial.c
===================================================================
--- trunk/LinuxBIOSv2/src/superio/ite/it8718f/it8718f_early_serial.c 2006-11-02 16:02:33 UTC (rev 2486)
+++ trunk/LinuxBIOSv2/src/superio/ite/it8718f/it8718f_early_serial.c 2006-11-04 23:19:00 UTC (rev 2487)
@@ -26,7 +26,7 @@
#define SIO_INDEX SIO_BASE
#define SIO_DATA SIO_BASE+1
-/* Global Configuration Registers. */
+/* Global configuration registers. */
#define IT8718F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8718F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8718F_CONFIG_REG_CONFIGSEL 0x22 /* Configuration Select. */
@@ -36,7 +36,7 @@
#define IT8718F_CONFIGURATION_PORT 0x2e /* Write-only. */
/* The content of IT8718F_CONFIG_REG_LDN (index 0x07) must be set to the
- * LDN the register belongs to, before you can access the register. */
+ LDN the register belongs to, before you can access the register. */
static void it8718f_sio_write(uint8_t ldn, uint8_t index, uint8_t value)
{
outb(IT8718F_CONFIG_REG_LDN, SIO_BASE);
@@ -45,7 +45,7 @@
outb(value, SIO_DATA);
}
-/* Enable the peripheral devices on the IT8718F Super IO chip. */
+/* Enable the peripheral devices on the IT8718F Super I/O chip. */
static void it8718f_enable_serial(device_t dev, unsigned iobase)
{
/* (1) Enter the configuration state (MB PnP mode). */
@@ -61,8 +61,8 @@
/* (2) Modify the data of configuration registers. */
/* Select the chip to configure (if there's more than one).
- * Set bit 7 to select JP3=1, clear bit 7 to select JP3=0.
- * If this register is not written, both chips are configured. */
+ Set bit 7 to select JP3=1, clear bit 7 to select JP3=0.
+ If this register is not written, both chips are configured. */
/* it8718f_sio_write(0x00, IT8718F_CONFIG_REG_CONFIGSEL, 0x00); */
/* Enable all devices. */
@@ -76,12 +76,12 @@
it8718f_sio_write(IT8718F_IR, 0x30, 0x1); /* Consumer IR */
/* Select 24MHz/48MHz CLKIN (set/clear bit 0). TODO: Needed? */
- /* it8718f_sio_write(0x00, IT8718F_CONFIG_REG_CLOCKSEL, 0x00); */
+ /* it8718f_sio_write(0x00, IT8718F_CONFIG_REG_CLOCKSEL, 0x01); */
/* Clear software suspend mode (clear bit 0). TODO: Needed? */
/* it8718f_sio_write(0x00, IT8718F_CONFIG_REG_SWSUSP, 0x00); */
/* (3) Exit the configuration state (MB PnP mode). */
- it8718f_sio_write(0x00, IT8718F_CONFIG_REG_CC, 0x02);
+ it8718f_sio_write(0x00, IT8718F_CONFIG_REG_CC, 0x02);
}
More information about the coreboot
mailing list