[LinuxBIOS] r2426 - in trunk/LinuxBIOSv2/src/mainboard: artecgroup/dbe61 digitallogic digitallogic/msm800sev

svn at openbios.org svn at openbios.org
Tue Sep 19 19:37:33 CEST 2006


Author: rminnich
Date: 2006-09-19 19:37:32 +0200 (Tue, 19 Sep 2006)
New Revision: 2426

Added:
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Config.lb
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Options.lb
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/auto.c
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/chip.h
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/cmos.layout
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/debug.c
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/failover.c
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/irq_tables.c
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/mainboard.c
   trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/reset.c
Removed:
   trunk/LinuxBIOSv2/src/mainboard/artecgroup/dbe61/cs5536_usb.c
Log:
add the msm800srv ; put the usb in the right place. 


Deleted: trunk/LinuxBIOSv2/src/mainboard/artecgroup/dbe61/cs5536_usb.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/artecgroup/dbe61/cs5536_usb.c	2006-09-19 16:44:14 UTC (rev 2425)
+++ trunk/LinuxBIOSv2/src/mainboard/artecgroup/dbe61/cs5536_usb.c	2006-09-19 17:37:32 UTC (rev 2426)
@@ -1,95 +0,0 @@
-#include <console/console.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include <device/pci_ops.h>
-
-#include <cpu/amd/lxdef.h>
-#include <cpu/x86/msr.h>
-
-#include "cs5536.h"
-
-#define GLIU2_P2D_BM_1			0x51010021					// southbridge GLIU P2D base mask descriptor
-#define USBMSRUOCB				0x5120000b					// USB option controller base address register
-#define UOCMUX					(USBOC_BASE_ADDRESS + 4)	// option controller native multiplex register
-
-#define USBOC_BASE_ADDRESS		0xe1017000		// USB option contoller base address, used only here
-#define USBOC_PORT4_FUNCTION	2				// USB port 4 desired function (0 = disabled, 2 = host, 3 = device)
-
-static void ohci_init(struct device *dev)
-{
-	uint32_t n;
-	msr_t msr;
-
-	printk_debug("USB: Setting up OHCI controller... ");
-
-	// enable controller bus mastering
-	n = pci_read_config32(dev, PCI_COMMAND);
-	pci_write_config32(dev, PCI_COMMAND, 
-		n | PCI_COMMAND_IO | PCI_COMMAND_MEMORY | 
-		PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE);
-
-	// set the USB option controller base address
-	msr.hi = 0x0000000a;
-	msr.lo = USBOC_BASE_ADDRESS;
-	wrmsr(USBMSRUOCB, msr);
-
-	// create the GLIU memory mapping
-	msr.hi = 0x40000000 | ((USBOC_BASE_ADDRESS >> 24) & 0x000000ff);
-	msr.lo = ((USBOC_BASE_ADDRESS << 8) & 0xfff00000) | 0x000fffff;
-	wrmsr(GLIU2_P2D_BM_1, msr);
-
-	// set the multiplex register with port 4 function
-	*((uint32_t*)UOCMUX) = USBOC_PORT4_FUNCTION;
-
-	// finally, disable the USB option controller memory mapping
-	msr.hi = 0x000000ff;
-	msr.lo = 0xfff00000;
-	wrmsr(GLIU2_P2D_BM_1, msr);
-    
-	printk_debug("done.\n");
-}
-
-static void ehci_init(struct device *dev)
-{
-	uint32_t cmd;
-	printk_debug("USB: Setting up EHCI controller... ");
-	
-	// enable controller bus mastering
-	cmd = pci_read_config32(dev, PCI_COMMAND);
-	pci_write_config32(dev, PCI_COMMAND, 
-		cmd | PCI_COMMAND_IO | PCI_COMMAND_MEMORY | 
-		PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE);
-
-	printk_debug("done.\n");
-}
-
-static struct device_operations ohci_ops  = {
-	.read_resources   = pci_dev_read_resources,
-	.set_resources    = pci_dev_set_resources,
-	.enable_resources = pci_dev_enable_resources,
-	.init             = ohci_init,
-	.scan_bus         = 0,
-	.enable           = southbridge_enable,
-};
-
-static struct device_operations ehci_ops  = {
-	.read_resources   = pci_dev_read_resources,
-	.set_resources    = pci_dev_set_resources,
-	.enable_resources = pci_dev_enable_resources,
-	.init             = ehci_init,
-	.scan_bus         = 0,
-	.enable           = southbridge_enable,
-};
-
-static struct pci_driver cs5536_usb1_driver __pci_driver = {
-	.ops    = &ohci_ops,
-	.vendor = PCI_VENDOR_ID_AMD,
-	.device = PCI_DEVICE_ID_AMD_CS5536_OHCI
-};
-
-static struct pci_driver cs5536_usb2_driver __pci_driver = {
-	.ops    = &ehci_ops,
-	.vendor = PCI_VENDOR_ID_AMD,
-	.device = PCI_DEVICE_ID_AMD_CS5536_EHCI
-};

Added: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Config.lb	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Config.lb	2006-09-19 17:37:32 UTC (rev 2426)
@@ -0,0 +1,157 @@
+##
+## Compute the location and size of where this firmware image
+## (linuxBIOS plus bootloader) will live in the boot rom chip.
+##
+if USE_FALLBACK_IMAGE
+	default ROM_SECTION_SIZE   = FALLBACK_SIZE
+	default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
+else
+	default ROM_SECTION_SIZE   = ( ROM_SIZE - FALLBACK_SIZE )
+	default ROM_SECTION_OFFSET = 0
+end
+
+##
+## Compute the start location and size size of
+## The linuxBIOS bootloader.
+##
+default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default PAYLOAD_SIZE            = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+
+##
+## Compute where this copy of linuxBIOS will start in the boot rom
+##
+default _ROMBASE      = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up linuxBIOS,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+default XIP_ROM_SIZE=65536
+default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+
+##
+## Set all of the defaults for an x86 architecture
+##
+
+arch i386 end
+
+##
+## Build the objects we have code for in this directory.
+##
+
+driver mainboard.o
+
+if HAVE_PIRQ_TABLE object irq_tables.o end
+#object reset.o
+
+##
+## Romcc output
+##
+makerule ./failover.E
+	depends "$(MAINBOARD)/failover.c ./romcc" 
+	action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+end
+
+makerule ./failover.inc
+	depends "$(MAINBOARD)/failover.c ./romcc"
+	action "./romcc    -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+end
+
+makerule ./auto.E 
+	depends	"$(MAINBOARD)/auto.c option_table.h ./romcc" 
+	action	"./romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+makerule ./auto.inc 
+	depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+	action	"./romcc    -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+
+##
+## Build our 16 bit and 32 bit linuxBIOS entry code
+##
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
+
+##
+## Build our reset vector (This is where linuxBIOS is entered)
+##
+if USE_FALLBACK_IMAGE 
+	mainboardinit cpu/x86/16bit/reset16.inc 
+	ldscript /cpu/x86/16bit/reset16.lds 
+else
+	mainboardinit cpu/x86/32bit/reset32.inc 
+	ldscript /cpu/x86/32bit/reset32.lds 
+end
+
+### Should this be in the northbridge code?
+mainboardinit arch/i386/lib/cpu_reset.inc
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+
+###
+### This is the early phase of linuxBIOS startup 
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+if USE_FALLBACK_IMAGE
+	ldscript /arch/i386/lib/failover.lds 
+	mainboardinit ./failover.inc
+end
+
+###
+### O.k. We aren't just an intermediary anymore!
+###
+
+##
+## Setup RAM
+##
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+mainboardinit ./auto.inc
+
+##
+## Include the secondary Configuration files 
+##
+dir /pc80
+config chip.h
+
+chip northbridge/amd/lx
+	# they keep changing this. 0:f.0 5c.w to see where it is
+	register "irqmap" = "0xbaba"
+	register "setupflash" = "1"
+	device apic_cluster 0 on
+		chip cpu/amd/model_lx
+			device apic 0 on end
+		end
+	end
+  	device pci_domain 0 on 
+    		device pci 1.0 on end
+		device pci 1.1 on end
+      		chip southbridge/amd/cs5536_lx
+                        register "enable_gpio0_inta" = "1"
+			register "enable_ide_nand_flash" = "0"
+			register "enable_uarta" = "1"
+			register "audio_irq" = "11"
+			register "usbf4_irq" = "11"
+			register "usbf11_irq" = "11"
+			register "usbf6_irq" = "11"
+			register "usbf7_irq" = "11"
+        		device pci d.0 on end	# EEPRO 1000
+        		device pci f.0 on end	# ISA Bridge
+        		device pci f.2 on end	# IDE Controller
+        		device pci f.3 on end 	# Audio
+        		device pci f.4 on end	# OHCI
+			device pci f.5 on end	# EHCI
+			register "unwanted_vpci[0]" = "0"	# End of list has a zero
+      		end
+    	end
+end
+

Added: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Options.lb
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Options.lb	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Options.lb	2006-09-19 17:37:32 UTC (rev 2426)
@@ -0,0 +1,162 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses HAVE_OPTION_TABLE
+uses USE_OPTION_TABLE
+uses CONFIG_ROM_STREAM
+uses IRQ_SLOT_COUNT
+uses MAINBOARD
+uses MAINBOARD_VENDOR
+uses MAINBOARD_PART_NUMBER
+uses LINUXBIOS_EXTRA_VERSION
+uses ARCH
+uses FALLBACK_SIZE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM_START
+uses CONFIG_COMPRESSED_ROM_STREAM_NRV2B
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses _RAMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses HAVE_MP_TABLE
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses OBJCOPY
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_CONSOLE_SERIAL8250
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses CONFIG_UDELAY_TSC
+uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
+
+## ROM_SIZE is the size of boot ROM that this board will use.
+default ROM_SIZE  = 256*1024
+
+###
+### Build options
+###
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## no MP table
+##
+default HAVE_MP_TABLE=0
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=0
+
+## Delay timer options
+##
+default CONFIG_UDELAY_TSC=1
+default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=0
+default IRQ_SLOT_COUNT=6
+
+#object irq_tables.o
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=0
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 65536
+default FALLBACK_SIZE = 131072
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default USE_OPTION_TABLE = 0
+
+default _RAMBASE = 0x00004000
+
+default CONFIG_ROM_STREAM     = 1
+
+##
+## The default compiler
+##
+default CROSS_COMPILE=""
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG      1   system is unusable               
+## ALERT      2   action must be taken immediately 
+## CRIT       3   critical conditions              
+## ERR        4   error conditions                 
+## WARNING    5   warning conditions               
+## NOTICE     6   normal but significant condition 
+## INFO       7   informational                    
+## DEBUG      8   debug-level messages             
+## SPEW       9   Way too many details             
+
+## Request this level of debugging output
+default  DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+default  MAXIMUM_CONSOLE_LOGLEVEL=8
+
+end
+

Added: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/auto.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/auto.c	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/auto.c	2006-09-19 17:37:32 UTC (rev 2426)
@@ -0,0 +1,193 @@
+#define ASSEMBLY 1
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/hlt.h>
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+//#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
+#include "cpu/x86/bist.h"
+#include "cpu/x86/msr.h"
+#include <cpu/amd/lxdef.h>
+
+//#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
+
+#include "southbridge/amd/cs5536/cs5536_early_smbus.c"
+#include "southbridge/amd/cs5536/cs5536_early_setup.c"
+
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+        return smbus_read_byte(device, address);
+}
+
+#include "northbridge/amd/lx/raminit.h"
+
+static inline unsigned int fls(unsigned int x)
+{
+        int r;
+
+        __asm__("bsfl %1,%0\n\t"
+                "jnz 1f\n\t"
+                "movl $32,%0\n"
+                "1:" : "=r" (r) : "g" (x));
+        return r;
+}
+
+
+
+
+/* sdram parameters for OLPC:
+	row address = 13
+	col address = 9
+	banks = 4
+	dimm0size=128MB
+	d0_MB=1 (module banks)
+	d0_cb=4 (component banks)
+	do_psz=4KB	(page size)
+	Trc=10 (clocks) (ref2act)
+	Tras=7 (act2pre)
+	Trcd=3 (act2cmd)
+	Trp=3   (pre2act)
+	Trrd=2 (act2act)
+	Tref=17.8ms
+  */
+static void sdram_set_spd_registers(const struct mem_controller *ctrl) 
+{
+	/* Total size of DIMM = 2^row address (byte 3) * 2^col address (byte 4) *
+	 *                      component Banks (byte 17) * module banks, side (byte 5) *
+	 *                      width in bits (byte 6,7)
+	 *                    = Density per side (byte 31) * number of sides (byte 5) */
+	/* 1. Initialize GLMC registers base on SPD values, do one DIMM for now */
+	msr_t msr;
+	unsigned char module_banks, val;
+
+	
+#if 0	//GX3
+	msr = rdmsr(MC_CF07_DATA);
+
+	/* get module banks (sides) per dimm, SPD byte 5 */
+	module_banks = 1;
+	module_banks >>= 1;
+	msr.hi &= ~(1 << CF07_UPPER_D0_MB_SHIFT);
+	msr.hi |= (module_banks << CF07_UPPER_D0_MB_SHIFT);
+
+	/* get component banks per module bank, SPD byte 17 */
+	val = 4;
+	val >>= 2;
+	msr.hi &= ~(0x1 << CF07_UPPER_D0_CB_SHIFT);
+	msr.hi |=  (val << CF07_UPPER_D0_CB_SHIFT);
+
+	/* get the module bank density, SPD byte 31  */
+	/* this is multiples of 8 MB */
+	/* actually it is 2^x*4, where x is the value you put in */
+	/* for OLPC, set default size */
+	/* dimm size - hardcoded 128Mb */
+	val = 5;
+	msr.hi &= ~(0xf << CF07_UPPER_D0_SZ_SHIFT);
+	msr.hi |=  (val << CF07_UPPER_D0_SZ_SHIFT);
+
+	/* page size = 2^col address */
+	val = 2; /* 4096 bytes */
+	msr.hi &= ~(0x7 << CF07_UPPER_D0_PSZ_SHIFT);
+	msr.hi |=  (val << CF07_UPPER_D0_PSZ_SHIFT);
+
+	print_debug("computed msr.hi ");
+	print_debug_hex32(msr.hi);
+	print_debug("\r\n");
+
+	/* this is a standard value, DOES NOT PROBABLY MATCH FROM ABOVE */
+	/* well, it may be close. It's about 200,000 ticks */
+	msr.lo = 0x00003000;
+	wrmsr(MC_CF07_DATA, msr);
+
+#endif
+	
+	msr.hi = 0x00005012;
+	msr.lo = 0x05000040;
+	
+	wrmsr(MC_CF07_DATA, msr);		//GX3
+
+	/* timing and mode ... */
+
+	//msr = rdmsr(0x20000019);
+	
+	/* per standard bios settings */	
+/*
+	msr.hi = 0x18000108;
+	msr.lo = 
+			(6<<28) |		// cas_lat
+			(10<<24)|		// ref2act
+			(7<<20)|		// act2pre
+			(3<<16)|		// pre2act
+			(3<<12)|		// act2cmd
+			(2<<8)|			// act2act
+			(2<<6)|			// dplwr
+			(2<<4)|			// dplrd
+			(3);			// dal
+	* the msr value reported by quanta is very, very different. 
+	 * we will go with that value for now. 
+	 *
+	//msr.lo = 0x286332a3;
+*/
+	//wrmsr(0x20000019, msr);	//GX3
+
+}
+
+#include "northbridge/amd/lx/raminit.c"
+#include "sdram/generic_sdram.c"
+
+#define PLLMSRhi 0x00001490
+#define PLLMSRlo 0x02000030
+#define PLLMSRlo1 ((0xde << 16) | (1 << 26) | (1 << 24))
+#define PLLMSRlo2 ((1<<14) |(1<<13) | (1<<0))
+#include "northbridge/amd/lx/pll_reset.c"
+#include "cpu/amd/model_lx/cpureginit.c"
+#include "cpu/amd/model_lx/syspreinit.c"
+static void msr_init(void)
+{
+	__builtin_wrmsr(0x1808,  0x10f3bf00, 0x22fffc02);
+
+	__builtin_wrmsr(0x10000020, 0xfff80, 0x20000000);
+        __builtin_wrmsr(0x10000021, 0x80fffe0, 0x20000000);
+
+        __builtin_wrmsr(0x40000020, 0xfff80, 0x20000000);
+        __builtin_wrmsr(0x40000021, 0x80fffe0, 0x20000000);
+}
+
+	
+static void main(unsigned long bist)
+{
+	static const struct mem_controller memctrl [] = {
+		{.channel0 = {(0xa<<3)|0, (0xa<<3)|1}}
+	};
+
+	SystemPreInit();			//GX3 OK
+
+	msr_init();					//GX3 OK
+
+	cs5536_early_setup();		//GX3 OK
+
+	/* NOTE: must do this AFTER the early_setup!
+	 * it is counting on some early MSR setup
+	 * for cs5536
+	 */
+	cs5536_setup_onchipuart();	//GX3 OK
+
+	uart_init();				//GX3 OK
+	console_init();				//GX3 OK
+
+	pll_reset();				//GX3 OK
+
+	cpuRegInit();				//GX3 OK
+
+	print_err("done cpuRegInit\n");
+	
+	sdram_initialize(1, memctrl);	//GX3 OK almost
+	
+	/* Check all of memory */
+	//ram_check(0x00000000, 640*1024);
+}

Added: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/chip.h
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/chip.h	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/chip.h	2006-09-19 17:37:32 UTC (rev 2426)
@@ -0,0 +1,5 @@
+extern struct chip_operations mainboard_digitallogic_msm800sev_ops;
+
+struct mainboard_digitallogic_msm800sev_config {
+	int nothing;
+};

Added: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/cmos.layout
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/cmos.layout	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/cmos.layout	2006-09-19 17:37:32 UTC (rev 2426)
@@ -0,0 +1,74 @@
+entries
+
+#start-bit length  config config-ID    name
+#0            8       r       0        seconds
+#8            8       r       0        alarm_seconds
+#16           8       r       0        minutes
+#24           8       r       0        alarm_minutes
+#32           8       r       0        hours
+#40           8       r       0        alarm_hours
+#48           8       r       0        day_of_week
+#56           8       r       0        day_of_month
+#64           8       r       0        month
+#72           8       r       0        year
+#80           4       r       0        rate_select
+#84           3       r       0        REF_Clock
+#87           1       r       0        UIP
+#88           1       r       0        auto_switch_DST
+#89           1       r       0        24_hour_mode
+#90           1       r       0        binary_values_enable
+#91           1       r       0        square-wave_out_enable
+#92           1       r       0        update_finished_enable
+#93           1       r       0        alarm_interrupt_enable
+#94           1       r       0        periodic_interrupt_enable
+#95           1       r       0        disable_clock_updates
+#96         288       r       0        temporary_filler
+0          384       r       0        reserved_memory
+384          1       e       4        boot_option
+385          1       e       4        last_boot
+386          1       e       1        ECC_memory
+388          4       r       0        reboot_bits
+392          3       e       5        baud_rate
+400          1       e       1        power_on_after_fail
+412          4       e       6        debug_level
+416          4       e       7        boot_first
+420          4       e       7        boot_second
+424          4       e       7        boot_third
+428          4       h       0        boot_index
+432	     8       h       0        boot_countdown
+1008         16      h       0        check_sum
+
+enumerations
+
+#ID value   text
+1     0     Disable
+1     1     Enable
+2     0     Enable
+2     1     Disable
+4     0     Fallback
+4     1     Normal
+5     0     115200
+5     1     57600
+5     2     38400
+5     3     19200
+5     4     9600
+5     5     4800
+5     6     2400
+5     7     1200
+6     6     Notice
+6     7     Info
+6     8     Debug
+6     9     Spew
+7     0     Network
+7     1     HDD
+7     2     Floppy
+7     8     Fallback_Network
+7     9     Fallback_HDD
+7     10    Fallback_Floppy
+#7     3     ROM
+
+checksums
+
+checksum 392 1007 1008
+
+

Added: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/debug.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/debug.c	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/debug.c	2006-09-19 17:37:32 UTC (rev 2426)
@@ -0,0 +1,66 @@
+
+static void print_debug_pci_dev(unsigned dev)
+{
+	print_debug("PCI: ");
+	print_debug_hex8((dev >> 16) & 0xff);
+	print_debug_char(':');
+	print_debug_hex8((dev >> 11) & 0x1f);
+	print_debug_char('.');
+	print_debug_hex8((dev >> 8) & 7);
+}
+
+static void print_pci_devices(void)
+{
+	device_t dev;
+	for(dev = PCI_DEV(0, 0, 0); 
+		dev <= PCI_DEV(0, 0x1f, 0x7); 
+		dev += PCI_DEV(0,0,1)) {
+		uint32_t id;
+		id = pci_read_config32(dev, PCI_VENDOR_ID);
+		if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0x0000)) {
+			continue;
+		}
+		print_debug_pci_dev(dev);
+		print_debug("\r\n");
+	}
+}
+
+static void dump_pci_device(unsigned dev)
+{
+	int i;
+	print_debug_pci_dev(dev);
+	print_debug("\r\n");
+	
+	for(i = 0; i <= 255; i++) {
+		unsigned char val;
+		if ((i & 0x0f) == 0) {
+			print_debug_hex8(i);
+			print_debug_char(':');
+		}
+		val = pci_read_config8(dev, i);
+		print_debug_char(' ');
+		print_debug_hex8(val);
+		if ((i & 0x0f) == 0x0f) {
+			print_debug("\r\n");
+		}
+	}
+}
+
+static void dump_pci_devices(void)
+{
+	device_t dev;
+	for(dev = PCI_DEV(0, 0, 0); 
+		dev <= PCI_DEV(0, 0x1f, 0x7); 
+		dev += PCI_DEV(0,0,1)) {
+		uint32_t id;
+		id = pci_read_config32(dev, PCI_VENDOR_ID);
+		if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0x0000)) {
+			continue;
+		}
+		dump_pci_device(dev);
+	}
+}

Added: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/failover.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/failover.c	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/failover.c	2006-09-19 17:37:32 UTC (rev 2426)
@@ -0,0 +1,32 @@
+#define ASSEMBLY 1
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include "arch/romcc_io.h"
+#include "pc80/mc146818rtc_early.c"
+
+static unsigned long main(unsigned long bist)
+{
+	/* This is the primary cpu how should I boot? */
+	if (do_normal_boot()) {
+		goto normal_image;
+	}
+	else {
+		goto fallback_image;
+	}
+ normal_image:
+	asm volatile ("jmp __normal_image" 
+		: /* outputs */ 
+		: "a" (bist) /* inputs */
+		: /* clobbers */
+		);
+ cpu_reset:
+	asm volatile ("jmp __cpu_reset"
+		: /* outputs */ 
+		: "a"(bist) /* inputs */
+		: /* clobbers */
+		);
+ fallback_image:
+	return bist;
+}

Added: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/irq_tables.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/irq_tables.c	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/irq_tables.c	2006-09-19 17:37:32 UTC (rev 2426)
@@ -0,0 +1,60 @@
+/* This file was generated by getpir.c, do not modify! 
+   (but if you do, please run checkpir on it to verify)
+ * Contains the IRQ Routing Table dumped directly from your memory, which BIOS sets up
+ *
+ * Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+
+#include <arch/pirq_routing.h>
+
+#define ID_SLOT_PCI_NET		1			// ThinCan ethernet
+#define ID_SLOT_PCI_RSVD1	2           // reserved entry 1
+#define ID_SLOT_PCI_RSVD3	3           // reserved entry 2
+#define ID_SLOT_PCI_RSVD2	4			// reserved entry 3
+#define ID_EMBED_PCI		0xff		// onboard PCI device
+
+// CS5535 PCI INT[A-D] Interrupt Routing lines.
+#define NO_CONNECT			0			// not used
+#define CS_PCI_INTA			1			// PCI INTA
+#define CS_PCI_INTB			2			// PCI INTB
+#define CS_PCI_INTC			3			// PCI INTC
+#define CS_PCI_INTD			4			// PCI INTD
+
+// IRQ bitmap reference line	FEDCBA9876543210
+//								0000110000100000b
+#define PCI_IRQ					0xc20	// PCI allowed IRQs here
+
+const struct irq_routing_table intel_irq_routing_table = 
+{
+	PIRQ_SIGNATURE,  /* u32 signature */
+	PIRQ_VERSION,    /* u16 version   */
+	32+16*6,		/* there can be total 2 devices on the bus */
+	0x00,		 /* Where the interrupt router lies (bus) */
+	(0x12<<3)|0x0,   /* Where the interrupt router lies (dev) */
+	0x0800,			/* IRQs devoted exclusively to PCI usage */
+	0x1022,			/* Vendor */
+	0x208f,			/* Device */
+	0x00000000,		/* Crap (miniport) */
+	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+	0xdf,         /*  u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+	{
+		/* bus,     dev|fn,   {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap},  slot, rfu */
+		// Geode GX3 Host Bridge and VGA Graphics
+		{0, 0x01<<3, {{CS_PCI_INTA, PCI_IRQ}, {NO_CONNECT, PCI_IRQ}, {NO_CONNECT, PCI_IRQ}, {NO_CONNECT, PCI_IRQ}}, ID_EMBED_PCI, 0x0},
+		// Realtek RTL8100/8139 Network Controller
+		{0, 0x0d<<3, {{CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}, {CS_PCI_INTA, PCI_IRQ}}, ID_SLOT_PCI_NET, 0x0},
+		// Reserved for future extensions
+		{0, 0x0c<<3, {{CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}}, ID_SLOT_PCI_RSVD1, 0x0},
+		// Geode CS5535/CS5536 IO Companion: USB controllers, IDE, Audio.
+		{0, 0x0f<<3, {{CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}}, ID_EMBED_PCI, 0x0},
+		// Reserved for future extensions
+		{0, 0x0e<<3, {{CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}, {CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}}, ID_SLOT_PCI_RSVD2, 0x0},
+		// Reserved for future extensions
+		{0, 0x0b<<3, {{CS_PCI_INTD, PCI_IRQ}, {CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}}, ID_SLOT_PCI_RSVD3, 0x0}
+	}
+};
+
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+        return copy_pirq_routing_table(addr);
+}

Added: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/mainboard.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/mainboard.c	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/mainboard.c	2006-09-19 17:37:32 UTC (rev 2426)
@@ -0,0 +1,49 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <arch/io.h>
+#include "chip.h"
+
+
+static void init(struct device *dev)
+{
+	unsigned bus = 0;
+	unsigned devNic = PCI_DEVFN(0xd, 0);	
+	unsigned devUsb = PCI_DEVFN(0xf, 4);
+	device_t usb = NULL, nic = NULL;
+	unsigned char irqUsb = 0xa, irqNic = 0xb;
+
+	printk_debug("DIGITALLOGIC MSM800SSEV  ENTER %s\n", __FUNCTION__);
+
+	// FIXME: do we need to initialize USB OHCI this way?
+	printk_debug("%s (%x,%x) set USB PCI interrupt line to %d\n", 
+		__FUNCTION__, bus, devUsb, irqUsb);
+
+	// initialize the USB controller
+	usb = dev_find_slot(bus, devUsb);
+	if (!usb) printk_err("Could not find USB\n");
+	else pci_write_config8(usb, PCI_INTERRUPT_LINE, irqUsb);
+
+	printk_debug("%s (%x,%x) set NIC PCI interrupt line to %d\n", 
+		__FUNCTION__, bus, devNic, irqNic);
+
+	// initialize theEEPRO 100
+	nic = dev_find_slot(bus, devNic);
+	if (!nic) printk_err("Could not find USB\n");
+	else pci_write_config8(nic, PCI_INTERRUPT_LINE, irqNic);
+
+	printk_debug("DIGITALLOGIC MSM800SSEV EXIT %s\n", __FUNCTION__);
+}
+
+static void enable_dev(struct device *dev)
+{
+        dev->ops->init = init;
+}
+
+struct chip_operations mainboard_digitallogic_msm800sev_ops = {
+	CHIP_NAME("digitallogip msm800sev mainboard ")
+        .enable_dev = enable_dev,
+
+};

Added: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/reset.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/reset.c	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/reset.c	2006-09-19 17:37:32 UTC (rev 2426)
@@ -0,0 +1,43 @@
+#if 0
+//#include "arch/romcc_io.h"
+#include <arch/io.h>
+
+typedef unsigned device_t;
+
+#define PCI_DEV(BUS, DEV, FN) ( \
+	(((BUS) & 0xFF) << 16) | \
+	(((DEV) & 0x1f) << 11) | \
+	(((FN)  & 0x7) << 8))
+
+static void pci_write_config8(device_t dev, unsigned where, unsigned char value)
+{
+        unsigned addr;
+        addr = dev | where;
+        outl(0x80000000 | (addr & ~3), 0xCF8);
+        outb(value, 0xCFC + (addr & 3));
+}
+
+static void pci_write_config32(device_t dev, unsigned where, unsigned value)
+{
+	unsigned addr;
+        addr = dev | where;
+        outl(0x80000000 | (addr & ~3), 0xCF8);
+        outl(value, 0xCFC);
+}
+
+static unsigned pci_read_config32(device_t dev, unsigned where)
+{
+	unsigned addr;
+        addr = dev | where;
+        outl(0x80000000 | (addr & ~3), 0xCF8);
+        return inl(0xCFC);
+}
+
+#include "../../../northbridge/amd/amdk8/reset_test.c"
+
+void hard_reset(void)
+{
+	set_bios_reset();
+	pci_write_config8(PCI_DEV(1, 0x04, 0), 0x47, 1);
+}
+#endif





More information about the coreboot mailing list