[LinuxBIOS] How do you usually install Fedora in LinuxBIOS
Vincente Tsou
vincentetsou at nexcom.com.tw
Wed May 16 13:47:14 CEST 2007
Hi,
I have a problem in LinuxBIOS when install Fedora,
First ,my platform is AMD SocketF + HT2100 + HT1000 and I have a bootable
LinuxBIOS already.
It can boot into SATA HD.
But i want to install fedora core 6 into SATA HD from PXE.
When i used PXE install, my system will hang and show some error massage.
Please see attached file.
Could you help me to vertify this question,or give me some suggest?
Thanks you very much for your kindly help.
--
Regards,
Vincente Tsou
Senior Engineer
R/D, S/W Dept.
NEXCOM International Co.
Tel: 886-2-82280606 Ext. 3205
Fax: 886-2-82280506
E-mail: vincentetsou at nexcom.com.tw
Web: http://www.nexcom.com/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.coreboot.org/pipermail/coreboot/attachments/20070516/a9a0c676/attachment.html>
-------------- next part --------------
Mekong BIOS Version:Z602-006
LinuxBIOS-2.0.0_Fallback ?T 5?? 16 17:38:46 CST 2007 starting...
bsp_apicid=00
01 nodes initialized.
core0 started:
SBLink=01
NC node|link=01
begin msr fid, vid 3106121206120202
set vid failed for apicid =00
end msr fid, vid 3106120606120212
ht reset -
Mekong BIOS Version:Z602-006
LinuxBIOS-2.0.0_Fallback ?T 5?? 16 17:38:46 CST 2007 starting...
bsp_apicid=00
01 nodes initialized.
core0 started:
SBLink=01
NC node|link=01
begin msr fid, vid 3106120606120212
end msr fid, vid 3106120606120212
SMBus controller enabled
Ram1.00
Ram2.00
Registered
266Mhz
RAM: 0x00100000 KB
Ram3
Initializing memory: done
Ram4
v_esp=000cefe4
testx = 5a5a5a5a
Copying data from cache to RAM -- switching to use RAM as stack... Done
testx = 5a5a5a5a
Disabling cache as ram now
Clearing initial memory region: Done
Copying LinuxBIOS to RAM.
src=fffe0000
dst=00100000
linxbios_ram.nrv2b length = 00008c1a
linxbios_ram.bin length = 0001750c
Jumping to LinuxBIOS.
LinuxBIOS-2.0.0_Fallback ?T 5?? 16 17:38:46 CST 2007 booting...
Enumerating buses...
APIC_CLUSTER: 0 enabled
PCI_DOMAIN: 0000 enabled
PCI: 00:18.3 siblings=1
CPU: APIC: 00 enabled
CPU: APIC: 01 enabled
PCI: pci_scan_bus for bus 00
PCI: 00:18.0 [1022/1100] enabled
PCI: 00:18.1 [1022/1101] enabled
PCI: 00:18.2 [1022/1102] enabled
PCI: 00:18.3 [1022/1103] enabled
Disabling static device: PCI: 00:19.0
Disabling static device: PCI: 00:19.1
Disabling static device: PCI: 00:19.2
Disabling static device: PCI: 00:19.3
PCI: 00:00.0 [1166/0140] enabled
PCI: 00:06.0 [1166/0140] enabled next_unitid: 000b
PCI: 00:00.0 subbordinate bus PCI-X
PCI: 00:00.0 [1166/0036] enabled
PCI: 00:0b.0 [1166/0036] enabled next_unitid: 000f
PCI: pci_scan_bus for bus 00
PCI: 00:01.0 [1166/0036] enabled
PCI: 00:02.0 [1166/0205] enabled
PCI: 00:02.1 [1166/0214] enabled
PCI: 00:02.2 [1166/0234] enabled
PCI: 00:02.3 [1166/0238] enabled
PCI: 00:02.4 [1166/0235] enabled
PCI: 00:02.5 [1166/0235] enabled
PCI: 00:02.6 [1166/0235] enabled
PCI: 00:03.0 [1166/0223] enabled
PCI: 00:03.1 [1166/0223] enabled
PCI: 00:03.2 [1166/0223] enabled
Disabling static device: PCI: 00:04.0
PCI: 00:06.0 [1166/0140] enabled
PCI: 00:07.0 [1166/0142] enabled
PCI: 00:08.0 [1166/0144] enabled
PCI: 00:09.0 [1166/0142] enabled
PCI: 00:0a.0 [1166/0144] enabled
PCI: pci_scan_bus for bus 01
PCI: 01:0d.0 subbordinate bus PCI-X
PCI: 01:0d.0 [1166/0104] enabled
PCI: 01:0e.0 [1166/024a] enabled
PCI: 01:0e.1 [1166/024a] enabled
PCI: pci_scan_bus for bus 02
PCI: 02:04.0 [8086/1010] enabled
PCI: 02:04.1 [8086/1010] enabled
PCI: pci_scan_bus returning with max=002
PCI: 02: Conventional PCI
PCI: pci_scan_bus returning with max=002
PCI: 01: 133MHz PCI-X
PNP: 002e.0 disabled
PNP: 002e.1 disabled
PNP: 002e.2 enabled
PNP: 002e.3 enabled
PNP: 002e.4 disabled
PNP: 002e.5 disabled
PNP: 002e.6 enabled
PNP: 002e.7 disabled
PNP: 002e.f disabled
PNP: 002e.10 enabled
PCI: pci_scan_bus for bus 03
PCI: pci_scan_bus returning with max=003
PCI: pci_scan_bus for bus 04
PCI: pci_scan_bus returning with max=004
PCI: pci_scan_bus for bus 05
PCI: pci_scan_bus returning with max=005
PCI: pci_scan_bus for bus 06
PCI: 06:00.0 [8086/105e] enabled
PCI: 06:00.1 [8086/105e] enabled
PCI: pci_scan_bus returning with max=006
PCI: pci_scan_bus for bus 07
PCI: 07:00.0 [8086/105e] enabled
PCI: 07:00.1 [8086/105e] enabled
PCI: pci_scan_bus returning with max=007
PCI: pci_scan_bus returning with max=007
PCI: pci_scan_bus returning with max=007
done
Allocating resources...
Reading resources...
PCI: 01:0d.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 02 prefmem
PCI: 00:01.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 01 prefmem
PCI: 00:06.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 03 io
PCI: 00:06.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 03 prefmem
PCI: 00:06.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 03 mem
PCI: 00:07.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 04 io
PCI: 00:07.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 04 prefmem
PCI: 00:07.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 04 mem
PCI: 00:08.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 05 io
PCI: 00:08.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 05 prefmem
PCI: 00:08.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 05 mem
PCI: 00:09.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 06 prefmem
PCI: 00:0a.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 07 prefmem
Done reading resources.
Setting resources...
PCI: 00:18.0 1b9 <- [0x00fc500000 - 0x00fc4fffff] prefmem <node 0 link 1>
PCI: 00:18.0 1c1 <- [0x0000001000 - 0x0000005fff] io <node 0 link 1>
PCI: 00:18.0 1b1 <- [0x00fc000000 - 0x00fc4fffff] mem <node 0 link 1>
PCI: 00:01.0 1c <- [0x0000001000 - 0x0000002fff] bus 01 io
PCI: 00:01.0 20 <- [0x00fc000000 - 0x00fc1fffff] bus 01 mem
PCI: 01:0d.0 1c <- [0x0000001000 - 0x0000001fff] bus 02 io
PCI: 01:0d.0 20 <- [0x00fc000000 - 0x00fc0fffff] bus 02 mem
PCI: 02:04.0 10 <- [0x00fc000000 - 0x00fc01ffff] mem64
PCI: 02:04.0 20 <- [0x0000001000 - 0x000000103f] io
PCI: 02:04.1 10 <- [0x00fc020000 - 0x00fc03ffff] mem64
PCI: 02:04.1 20 <- [0x0000001040 - 0x000000107f] io
PCI: 01:0e.0 10 <- [0x0000002030 - 0x0000002037] io
PCI: 01:0e.0 14 <- [0x0000002070 - 0x0000002073] io
PCI: 01:0e.0 18 <- [0x0000002040 - 0x0000002047] io
PCI: 01:0e.0 1c <- [0x0000002080 - 0x0000002083] io
PCI: 01:0e.0 20 <- [0x0000002000 - 0x000000201f] io
PCI: 01:0e.0 24 <- [0x00fc100000 - 0x00fc101fff] mem
PCI: 01:0e.1 10 <- [0x0000002050 - 0x0000002057] io
PCI: 01:0e.1 14 <- [0x0000002090 - 0x0000002093] io
PCI: 01:0e.1 18 <- [0x0000002060 - 0x0000002067] io
PCI: 01:0e.1 1c <- [0x00000020a0 - 0x00000020a3] io
PCI: 01:0e.1 20 <- [0x0000002020 - 0x000000202f] io
PCI: 00:02.0 90 <- [0x0000005c00 - 0x0000005c0f] io
PCI: 00:02.1 10 <- [0x0000005c20 - 0x0000005c27] io
PCI: 00:02.1 14 <- [0x0000005c40 - 0x0000005c43] io
PCI: 00:02.1 18 <- [0x0000005c30 - 0x0000005c37] io
PCI: 00:02.1 1c <- [0x0000005c50 - 0x0000005c53] io
PCI: 00:02.1 20 <- [0x0000005c10 - 0x0000005c1f] io
PCI: 00:02.1 64 <- [0x0000005c60 - 0x0000005c63] io
PNP: 002e.2 60 <- [0x00000002f8 - 0x00000002ff] io
PNP: 002e.2 70 <- [0x0000000003 - 0x0000000003] irq
ERROR: PNP: 002e.2 74 drq size: 0x0000000001 not assigned
ERROR: PNP: 002e.2 75 drq size: 0x0000000001 not assigned
PNP: 002e.3 60 <- [0x00000003f8 - 0x00000003ff] io
PNP: 002e.3 70 <- [0x0000000004 - 0x0000000004] irq
PNP: 002e.6 60 <- [0x0000000060 - 0x0000000067] io
PNP: 002e.6 62 <- [0x0000000064 - 0x000000006b] io
PNP: 002e.6 70 <- [0x0000000001 - 0x0000000001] irq
PNP: 002e.10 60 <- [0x0000000070 - 0x0000000071] io
PNP: 002e.10 62 <- [0x0000000072 - 0x0000000073] io
PCI: 00:02.3 10 <- [0x00fc400000 - 0x00fc400fff] mem
PCI: 00:02.4 10 <- [0x00fc401000 - 0x00fc401fff] mem
PCI: 00:02.5 10 <- [0x00fc402000 - 0x00fc402fff] mem
PCI: 00:02.6 10 <- [0x00fc403000 - 0x00fc403fff] mem
PCI: 00:03.0 10 <- [0x00fc404000 - 0x00fc404fff] mem
PCI: 00:03.0 14 <- [0x0000005000 - 0x00000050ff] io
PCI: 00:03.1 10 <- [0x00fc405000 - 0x00fc405fff] mem
PCI: 00:03.1 14 <- [0x0000005400 - 0x00000054ff] io
PCI: 00:03.2 10 <- [0x00fc406000 - 0x00fc406fff] mem
PCI: 00:03.2 14 <- [0x0000005800 - 0x00000058ff] io
PCI: 00:09.0 1c <- [0x0000003000 - 0x0000003fff] bus 06 io
PCI: 00:09.0 20 <- [0x00fc200000 - 0x00fc2fffff] bus 06 mem
PCI: 06:00.0 10 <- [0x00fc200000 - 0x00fc21ffff] mem
PCI: 06:00.0 14 <- [0x00fc220000 - 0x00fc23ffff] mem
PCI: 06:00.0 18 <- [0x0000003000 - 0x000000301f] io
PCI: 06:00.0 30 <- [0x00fc240000 - 0x00fc25ffff] romem
PCI: 06:00.1 10 <- [0x00fc260000 - 0x00fc27ffff] mem
PCI: 06:00.1 14 <- [0x00fc280000 - 0x00fc29ffff] mem
PCI: 06:00.1 18 <- [0x0000003020 - 0x000000303f] io
PCI: 06:00.1 30 <- [0x00fc2a0000 - 0x00fc2bffff] romem
PCI: 00:0a.0 1c <- [0x0000004000 - 0x0000004fff] bus 07 io
PCI: 00:0a.0 20 <- [0x00fc300000 - 0x00fc3fffff] bus 07 mem
PCI: 07:00.0 10 <- [0x00fc300000 - 0x00fc31ffff] mem
PCI: 07:00.0 14 <- [0x00fc320000 - 0x00fc33ffff] mem
PCI: 07:00.0 18 <- [0x0000004000 - 0x000000401f] io
PCI: 07:00.0 30 <- [0x00fc340000 - 0x00fc35ffff] romem
PCI: 07:00.1 10 <- [0x00fc360000 - 0x00fc37ffff] mem
PCI: 07:00.1 14 <- [0x00fc380000 - 0x00fc39ffff] mem
PCI: 07:00.1 18 <- [0x0000004020 - 0x000000403f] io
PCI: 07:00.1 30 <- [0x00fc3a0000 - 0x00fc3bffff] romem
PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart>
Done setting resources.
Done allocating resources.
Enabling resources...
PCI: 00:18.0 cmd <- 140
PCI: 00:01.0 bridge ctrl <- 0003
PCI: 00:01.0 cmd <- 147
PCI: 01:0d.0 bridge ctrl <- 0003
PCI: 01:0d.0 cmd <- 147
PCI: 02:04.0 cmd <- 143
PCI: 02:04.1 cmd <- 143
PCI: 01:0e.0 subsystem <- 1933/1011
PCI: 01:0e.0 cmd <- 143
PCI: 01:0e.1 subsystem <- 1933/1011
PCI: 01:0e.1 cmd <- 141
PCI: 00:02.0 subsystem <- 1933/1011
PCI: 00:02.0 cmd <- 147
PCI: 00:02.1 subsystem <- 1933/1011
PCI: 00:02.1 cmd <- 141
PCI: 00:02.2 subsystem <- 1933/1011
PCI: 00:02.2 cmd <- 144
bcm5785lpc decode:PNP: 002e.2, base=0x000002f8, end=0x000002ff
bcm5785lpc decode:PNP: 002e.3, base=0x000003f8, end=0x000003ff
bcm5785lpc decode:PNP: 002e.6, base=0x00000060, end=0x00000067
bcm5785lpc decode:PNP: 002e.6, base=0x00000064, end=0x0000006b
bcm5785lpc decode:PNP: 002e.10, base=0x00000070, end=0x00000071
bcm5785lpc decode:PNP: 002e.10, base=0x00000072, end=0x00000073
PCI: 00:02.3 subsystem <- 1933/1011
PCI: 00:02.3 cmd <- 146
PCI: 00:02.4 subsystem <- 1933/1011
PCI: 00:02.4 cmd <- 146
PCI: 00:02.5 subsystem <- 1933/1011
PCI: 00:02.5 cmd <- 146
PCI: 00:02.6 subsystem <- 1933/1011
PCI: 00:02.6 cmd <- 146
PCI: 00:03.0 subsystem <- 1933/1011
PCI: 00:03.0 cmd <- 143
PCI: 00:03.1 subsystem <- 1933/1011
PCI: 00:03.1 cmd <- 143
PCI: 00:03.2 subsystem <- 1933/1011
PCI: 00:03.2 cmd <- 143
PCI: 00:06.0 bridge ctrl <- 0003
PCI: 00:06.0 subsystem <- 1933/1011
PCI: 00:06.0 cmd <- 140
PCI: 00:07.0 bridge ctrl <- ffff
PCI: 00:07.0 subsystem <- 1933/1011
PCI: 00:07.0 cmd <- ffff
PCI: 00:08.0 bridge ctrl <- ffff
PCI: 00:08.0 subsystem <- 1933/1011
PCI: 00:08.0 cmd <- ffff
PCI: 00:09.0 bridge ctrl <- ffff
PCI: 00:09.0 subsystem <- 1933/1011
PCI: 00:09.0 cmd <- ffff
PCI: 06:00.0 cmd <- ffff
PCI: 06:00.1 cmd <- ffff
PCI: 00:0a.0 bridge ctrl <- ffff
PCI: 00:0a.0 subsystem <- 1933/1011
PCI: 00:0a.0 cmd <- ffff
PCI: 07:00.0 cmd <- ffff
PCI: 07:00.1 cmd <- ffff
PCI: 00:18.1 subsystem <- 1933/1011
PCI: 00:18.1 cmd <- 140
PCI: 00:18.2 subsystem <- 1933/1011
PCI: 00:18.2 cmd <- 140
PCI: 00:18.3 cmd <- 140
done.
Initializing devices...
Root Device init
APIC_CLUSTER: 0 init
start_eip=0x0000d000, offset=0x00100000, code_size=0x0000005b
Initializing CPU #1
Initializing CPU #0
CPU: vendor AMD device 40f12
CPU: vendor AMD device 40f12
CPU: family 0f, model 41, stepping 02
CPU: family 0f, model 41, stepping 02
brandId=0353
brandId=0353
Enabling cache
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 1024MB, type WB
Setting variable MTRR 0, base: 0MB, range: 1024MB, type WB
DONE variable MTRRs
Clear out the extra MTRR's
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
CPU model AMD Opteron(tm) Processor 176
CPU model AMD Opteron(tm) Processor 176
Setting up local apic...Setting up local apic... apic_id: 0x00 done.
apic_id: 0x01 done.
Clearing memory 2048K - 1048576K: CPU #1 Initialized
--------------- done
CPU #0 Initialized
All AP CPUs stopped
PCI: 00:18.0 init
PCI: 00:07.0 init
PCI: 00:08.0 init
PCI: 00:09.0 init
PCI: 00:0a.0 init
PCI: 01:0e.0 init
init PHY...
port 0 PHY status = 13
port 1 PHY status = 04
after reset port 1 PHY status = 04
port 2 PHY status = 04
after reset port 2 PHY status = 04
port 3 PHY status = 04
after reset port 3 PHY status = 04
PCI: 01:0e.1 init
PCI: 00:02.0 init
PCI: 00:02.1 init
PCI: 00:02.2 init
RTC Init
PNP: 002e.2 init
PNP: 002e.3 init
PNP: 002e.6 init
PNP: 002e.10 init
PCI: 00:02.3 init
PCI: 00:02.4 init
PCI: 00:02.5 init
PCI: 00:02.6 init
PCI: 00:03.0 init
PCI: 00:03.1 init
PCI: 00:03.2 init
PCI: 00:18.1 init
PCI: 00:18.2 init
PCI: 00:18.3 init
NB: Function 3 Misc Control.. done.
PCI: 02:04.0 init
PCI: 02:04.1 init
PCI: 06:00.0 init
PCI: 06:00.1 init
PCI: 07:00.0 init
PCI: 07:00.1 init
Devices initialized
bus_isa=0
bus_isa=0
bus_isa=0
bus_isa=0
bus_isa=0
Writing IRQ routing tables to 0xf0000...Assigning IRQ 10 to 0:3.0
Readback = 10
Assigning IRQ 10 to 0:3.1
Readback = 10
Assigning IRQ 10 to 0:3.2
Readback = 10
Assigning IRQ 15 to 1:e.0
Readback = 15
Assigning IRQ 15 to 1:e.1
Readback = 15
Assigning IRQ 9 to 2:4.0
Readback = 9
Assigning IRQ 10 to 2:4.1
Readback = 10
Assigning IRQ 11 to 0:3.0
Readback = 11
Assigning IRQ 11 to 0:3.1
Readback = 11
Assigning IRQ 11 to 0:3.2
Readback = 11
done.
Wrote the mp table end at: 00000020 - 000001bc
initialize Hardware Monitor
Moving GDT to 0x500...ok
Wrote linuxbios table at: 00000530 - 000006d0 checksum 8408
BIOS OK!
Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3
rom_stream: 0xfffc0000 - 0xfffdffff
Found ELF candidate at offset 0
Loading Etherboot version: 5.2.6
Dropping non PT_LOAD segment
New segment addr 0x20000 size 0x4a60e offset 0xb0 filesize 0xbbb1
(cleaned up) New segment addr 0x20000 size 0x4a60e offset 0xb0 filesize 0xbbb1
Loading Segment: addr: 0x0000000000020000 memsz: 0x000000000004a60e filesz: 0x000000000000bbb1
Clearing Segment: addr: 0x000000000002bbb1 memsz: 0x000000000003ea5d
Jumping to boot code at 0x20000
ROM segment 0x0000 length 0x0000 reloc 0x00020000
CPU 2715 Mhz
Etherboot 5.2.6 (GPL) http://etherboot.org Tagged ELF for [E1000][FILO]
Relocating _text from: [0002bbc0,0006c470) to [3febf750,3ff00000)
Boot from (N)etwork (D)isk (F)loppy or (Q)uit? N
Probing pci nic...
[e1000-82546eb-copper]Ethernet addr: 00:10:F3:05:E7:9A
Searching for server (DHCP)...
..Me: 172.16.0.228, Server: 172.16.0.1, Gateway 172.16.0.1
Loading 172.16.0.1:etherboot/FC6.elf ...(ELF)... ...........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................done
Firmware type: LinuxBIOS
Linux version 2.6.15-1.2054_FC5 (bhcompile at hs20-bc1-2.build.redhat.com) (gcc version 4.1.0 20060304 (Red Hat 4.1.0-3)) #1 Tue Mar 14 15:48:03 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000000738 (reserved)
BIOS-e820: 0000000000000738 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000040000000 (usable)
128MB HIGHMEM available.
895MB LOWMEM available.
found SMP MP-table at 00000010
Using x86 segment limits to approximate NX protection
DMI not present or invalid.
ACPI: Unable to locate RSDP
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: NEXCOM Product ID: MEKONG APIC at: 0xFEE00000
Processor #0 15:1 APIC version 16
Processor #1 15:1 APIC version 16
WARNING: NR_CPUS limit of 1 reached. Processor ignored.
I/O APIC #2 Version 17 at 0xFEC00000.
I/O APIC #3 Version 17 at 0xFEC01000.
I/O APIC #4 Version 17 at 0xFEC02000.
Enabling APIC mode: Flat. Using 3 I/O APICs
Processors: 1
Allocating PCI resources starting at 50000000 (gap: 40000000:c0000000)
Built 1 zonelists
Kernel command line: ks=nfs:172.16.0.1:/opt/FC6/ks.cfg ksdevice=eth0 selinux=0 ramdisk_size=32768 ro initrd=initrd.img root=/dev/ram console=ttyS0,115200
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c03c4000 soft=c03c3000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2593.770 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030744k/1048576k available (1884k kernel code, 17148k reserved, 744k data, 172k init, 131076k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5195.07 BogoMIPS (lpj=10390158)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Opteron(tm) Processor 176 stepping 02
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
unknown bus type 1.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 1.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 2.
unknown bus type 2.
unknown bus type 2.
unknown bus type 2.
unknown bus type 1.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 2.
unknown bus type 2.
unknown bus type 2.
unknown bus type 2.
unknown bus type 1.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 2.
unknown bus type 2.
unknown bus type 2.
unknown bus type 2.
unknown bus type 1.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 2.
unknown bus type 2.
unknown bus type 2.
unknown bus type 2.
unknown bus type 1.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 255.
unknown bus type 2.
unknown bus type 2.
unknown bus type 2.
unknown bus type 2.
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 4859k freed
NET: Registered protocol family 16
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.1
PCI: Unable to handle 64-bit address space for bridge 0000:00:01.0
PCI: Unable to handle 64-bit address space for bridge 0000:01:0d.0
PCI: Using IRQ router default [1166/0036] at 0000:00:01.0
PCI BIOS passed nonexistent PCI bus 0!
PCI BIOS passed nonexistent PCI bus 0!
PCI BIOS passed nonexistent PCI bus 0!
PCI BIOS passed nonexistent PCI bus 1!
PCI BIOS passed nonexistent PCI bus 0!
PCI BIOS passed nonexistent PCI bus 1!
PCI BIOS passed nonexistent PCI bus 0!
PCI BIOS passed nonexistent PCI bus 2!
PCI BIOS passed nonexistent PCI bus 1!
PCI BIOS passed nonexistent PCI bus 2!
PCI BIOS passed nonexistent PCI bus 1!
PCI: Bridge: 0000:01:0d.0
IO window: 1000-1fff
MEM window: fc000000-fc0fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:01.0
IO window: 1000-2fff
MEM window: fc000000-fc1fffff
PREFETCH window: 50000000-500fffff
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(948578392.648:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key C09F750F2EDE9E7B
- key was been created 193790735 seconds in future
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
?serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks HT1000: IDE controller at PCI slot 0000:00:02.1
SvrWks HT1000: chipset revision 0
SvrWks HT1000: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x5c10-0x5c17, BIOS settings: hda:pio, hdb:pio
double fault, gdt at c1807000 [255 bytes]
More information about the coreboot
mailing list