[LinuxBIOS] #87: flashrom issues on m57sli-s4

[Carl-Daniel Hailfinger]

Hi Ward,

On 08.11.2007 16:51, Carl-Daniel Hailfinger wrote:
> On 08.11.2007 16:22, Ward Vandewege wrote:
>   
>> On Thu, Nov 08, 2007 at 02:05:16PM -0000, LinuxBIOS wrote:
>>   
>>     
>>> #87: flashrom issues on m57sli-s4
>>>
>>>  I need superiotool output for a board with parallel flash running under
>>>  LB. NOW.
>>>     
>>>       
>> LinuxBIOS:          http://ward.vandewege.net/superiotool-lb.m57sli.dump
>> Proprietary BIOS:   http://ward.vandewege.net/superiotool-prop.m57sli.dump
>>     

Can you retest with the following patch applied? Thanks.

> The "wtf?!?" comment is intentional and designates another bug. However,
> I have no idea which device number we need here.
>   

Regards,
Carl-Daniel


Try to fix a few loose ends on the GA-M57SLI Super I/O GPIO configuration.

Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006 at gmx.net>

---

Index: LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb
===================================================================
--- LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb	(Revision 2953)
+++ LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb	(Arbeitskopie)
@@ -239,7 +239,9 @@
 					device pci 0.0 on end   # HT
                 			device pci 1.0 on # LPC
 						chip superio/ite/it8716f
-							device pnp 2e.0 off #  Floppy
+							device pnp 2e.0 off #  Floppy and anyLDN
+								irq 0x23 = 0x11 # watchdog from CLKIN, CLKIN = 24 MHz
+								#0x24 = 0x1a # serial flash (SPI only)
                 	                 			io 0x60 = 0x3f0
                 	                			irq 0x70 = 6
                 	                			drq 0x74 = 2
@@ -269,6 +271,30 @@
                 	        			device pnp 2e.6 on #  Mouse
                 	                			irq 0x70 = 12
 							end
+                	        			device pnp 2e.7 on #  GPIO, SPI flash
+								irq 0x25 = 0x0 # pin 84 is not GP10
+								irq 0x26 = 0x43 # pin 21 is GP26, pin 26 is GP21, pin 27 is GP20
+								irq 0x27 = 0x20 # pin 13 is GP35
+								#0x28 = 0x0 # pin 70 is not GP46
+								irq 0x29 = 0x81 # pin 6,3,128,127,126 is GP63,64,65,66,67
+								#0x2c = 0x1f # Enable FAN_CTL/FAN_TAC set to 5 (pin 21,23), enable FAN_CTL/FAN_TAC set to 4 (pin 20,22), pin 48 is PCIRST5#, pin91 is PCIRSTIN#, VIN7 is internal voltage divider for VCCH5V, pin 95 is ATXPG, VIN3 is internal voltage divider for VCC5V
+								io 0x62 = 0x800 # simple i/o base
+                	                			#io 0x64 = 0x820 # serial flash io (SPI only)
+								#0x71 = 0x1 # watch dog force timeout (parallel flash only)
+								irq 0x72 = 0x0 # no WDT interrupt
+								irq 0xb8 = 0x0 # GPIO pin set 1 disable internal pullup
+								irq 0xbc = 0x01 # GPIO pin set 5 enable internal pullup
+								#0xc0 = 0x0 # SIO pin set 1 alternate function
+								irq 0xc1 = 0x43 # SIO pin set 2 mixed function
+								irq 0xc2 = 0x20 # SIO pin set 3 mixed function
+								#0xc3 = 0x0 # SIO pin set 4 alternate function
+								#0xc8 = 0x0 # SIO pin set 1 input mode
+								irq 0xc9 = 0x0 # SIO pin set 2 mixed input/output mode
+								#0xcb = 0x0 # SIO pin set 4 input mode
+								#0xf0 = 0x10 # generate SMI# on EC IRQ
+								#0xf1 = 0x40 # SMI# level trigger
+								irq 0xf6 = 0x28 # HWMON alert beep pin location
+							end
                 	        			device pnp 2e.8 off #  MIDI
 								io 0x60 = 0x300
 								irq 0x70 = 10
@@ -305,6 +331,7 @@
                                                         device i2c 57 on end
                                                 end 
 					end # SM
+#wtf?!? we already have device pci 1.1 in the section above
                                         device pci 1.1 on # SM 1
 #PCI device smbus address will depend on addon pci device, do we need to scan_smbus_bus?
 #                                                chip drivers/generic/generic #PCIXA Slot1