[LinuxBIOS] alix1c for v3 update
Corey Osgood
corey.osgood at gmail.com
Tue Nov 27 17:24:34 CET 2007
Great work, but I'm gonna be a pain...
ron minnich wrote:
> Updated support for the ALIX 1C. This code gets as far as pll_reset and dies.
>
> Signed-off-by: Ronald G. Minnich <rminnich at gmail.com>
>
> Index: mainboard/pcengines/Kconfig
> ===================================================================
> --- mainboard/pcengines/Kconfig (revision 524)
> +++ mainboard/pcengines/Kconfig (working copy)
> @@ -30,6 +30,7 @@
> select OPTION_TABLE
> select NORTHBRIDGE_AMD_GEODELX
> select SOUTHBRIDGE_AMD_CS5536
> + select SUPERIO_WINBOND_W83627HF
> help
> PC Engines ALIX1.C.
>
> Index: mainboard/pcengines/alix1c/initram.c
> ===================================================================
> --- mainboard/pcengines/alix1c/initram.c (revision 524)
> +++ mainboard/pcengines/alix1c/initram.c (working copy)
> @@ -30,47 +30,117 @@
> #include <io.h>
> #include <amd_geodelx.h>
> #include <northbridge/amd/geodelx/raminit.h>
> +#include <spd.h>
>
> -#define MANUALCONF 0 /* Do automatic strapped PLL config. */
> -
> -#define PLLMSRHI 0x00001490 /* Manual settings for the PLL */
> +#define MANUALCONF 0 /* Do automatic strapped PLL config */
> +#define PLLMSRHI 0x00001490 /* manual settings for the PLL */
> #define PLLMSRLO 0x02000030
> -
> #define DIMM0 ((u8) 0xA0)
> #define DIMM1 ((u8) 0xA2)
>
> +/* The part is a Hynix hy5du121622ctp-d43.
> + *
> + * HY 5D U 12 16 2 2 C <blank> T <blank> P D43
> + * Hynix
> + * DDR SDRAM (5D)
> + * VDD 2.5 VDDQ 2.5 (U)
> + * 512M 8K REFRESH (12)
> + * x16 (16)
> + * 4banks (2)
> + * SSTL_2 (2)
> + * 4th GEN die (C)
> + * Normal Power Consumption (<blank> )
> + * TSOP (T)
> + * Single Die (<blank>)
> + * Lead Free (P)
> + * DDR400 3-3-3 (D43)
> + */
> +/* SPD array */
> +static const u8 spdbytes[] = {
> + [SPD_ACCEPTABLE_CAS_LATENCIES] = 0x10,
> + [SPD_BANK_DENSITY] = 0x40,
> + [SPD_DEVICE_ATTRIBUTES_GENERAL] = 0xff,
> + [SPD_MEMORY_TYPE] = 7,
> + [SPD_MIN_CYCLE_TIME_AT_CAS_MAX] = 10, /* A guess for the tRAC value */
>
This looks like it's wrong, a normal DDR400 dimm is 0x50 or so.
> + [SPD_MODULE_ATTRIBUTES] = 0xff, /* FIXME later when we figure out. */
>
0x20 for an unbuffered dimm, 0x26 for registered.
> + [SPD_NUM_BANKS_PER_SDRAM] = 4,
> + [SPD_PRIMARY_SDRAM_WIDTH] = 8,
> + [SPD_NUM_DIMM_BANKS] = 1, /* ALIX1.C is 1 bank. */
> + [SPD_NUM_COLUMNS] = 0xa,
> + [SPD_NUM_ROWS] = 3,
> + [SPD_REFRESH] = 0x3a,
> + [SPD_SDRAM_CYCLE_TIME_2ND] = 60,
> + [SPD_SDRAM_CYCLE_TIME_3RD] = 75,
> + [SPD_tRAS] = 40,
> + [SPD_tRCD] = 15,
> + [SPD_tRFC] = 70,
> + [SPD_tRP] = 15,
> + [SPD_tRRD] = 10,
> +};
> +
> +u8 spd_read_byte(u16 device, u8 address)
> +{
> + printk(BIOS_DEBUG, "spd_read_byte dev %04x\n", device);
> +
> + if (device != (0x50 << 1)) {
> + printk(BIOS_DEBUG, " returns 0xff\n");
> + return 0xff;
> + }
> +
> + printk(BIOS_DEBUG, " addr %02x returns %02x\n", address, spdbytes[address]);
> +
> + return spdbytes[address];
> +}
> +
> /**
> - * Placeholder in case we ever need it. Since this file is a template for
> - * other boards, we want this here and we want the call in the right place.
> - */
> + * Place holder in case we ever need it. Since this file is a
>
place holder -> placeholder?
> + * template for other motherboards, we want this here and we want the
> + * call in the right place.
> + */
> +
> static void mb_gpio_init(void)
> {
> /* Early mainboard specific GPIO setup */
> }
>
> -/**
> - * Main for initram for the PC Engines ALIX1.C. It might seem that you could
> - * somehow do these functions in, e.g., the CPU code, but the order of
> - * operations and what those operations are is VERY strongly mainboard
> - * dependent. It's best to leave it in the mainboard code.
> - */
> +/**
> + * main for initram for the PC Engines Alix 1C. It might seem that you
>
main()?
> + * could somehow do these functions in, e.g., the cpu code, but the
> + * order of operations and what those operations are is VERY strongly
> + * mainboard dependent. It's best to leave it in the mainboard code.
> + */
> int main(void)
> {
> - u8 smb_devices[] = { DIMM0, DIMM1 };
> -
> + u8 smb_devices[] = {
> + DIMM0, DIMM1
> + };
> + printk(BIOS_DEBUG, "Hi there from stage1\n");
> post_code(POST_START_OF_MAIN);
>
> system_preinit();
> + printk(BIOS_DEBUG, "done preinit\n");
> +
> mb_gpio_init();
> + printk(BIOS_DEBUG, "done gpio init\n");
> +
> pll_reset(MANUALCONF, PLLMSRHI, PLLMSRLO);
> + printk(BIOS_DEBUG, "done pll reset\n");
> +
> cpu_reg_init(0, DIMM0, DIMM1);
> + printk(BIOS_DEBUG, "done cpu reg init\n");
>
> sdram_set_registers();
> + printk(BIOS_DEBUG, "done sdram set registers\n");
> +
> sdram_set_spd_registers(DIMM0, DIMM1);
> + printk(BIOS_DEBUG, "done sdram set spd registers\n");
> +
> sdram_enable(DIMM0, DIMM1);
> + printk(BIOS_DEBUG, "done sdram enable\n");
>
> - /* Check memory. */
> - /* ram_check(0, 640 * 1024); */
> + /* Check low memory */
> + /*ram_check(0x00000000, 640*1024); */
>
> + printk(BIOS_DEBUG, "stage1 returns\n");
> return 0;
> }
> Index: mainboard/pcengines/alix1c/stage1.c
> ===================================================================
> --- mainboard/pcengines/alix1c/stage1.c (revision 524)
> +++ mainboard/pcengines/alix1c/stage1.c (working copy)
> @@ -28,20 +28,24 @@
> #include <io.h>
> #include <amd_geodelx.h>
> #include <southbridge/amd/cs5536/cs5536.h>
> +#include <superio/winbond/w83627hf/w83627hf.h>
>
> +#define SERIAL_DEV W83627HF_SP1
> +#define SERIAL_IOBASE 0x3f8
> +
> void hardware_stage1(void)
> {
> + void w83627hf_enable_serial(u8 dev, u8 serial, u16 iobase);
> post_code(POST_START_OF_MAIN);
> -
> geodelx_msr_init();
>
> cs5536_stage1();
>
> - /* NOTE: Must do this AFTER the early_setup! It is counting on some
> - * early MSR setup for the CS5536. We do this early for debug.
> - * Real setup should be done in chipset init via Config.lb.
> - *
> - * TODO: Drop Config.lb reference, update comment.
> + /* NOTE: must do this AFTER the early_setup!
> + * it is counting on some early MSR setup
> + * for cs5536.
> */
> - cs5536_setup_onchipuart();
> + cs5536_disable_internal_uart();
> + w83627hf_enable_serial(0x2e, SERIAL_DEV, SERIAL_IOBASE);
> +
> }
> Index: mainboard/pcengines/alix1c/dts
> ===================================================================
> --- mainboard/pcengines/alix1c/dts (revision 524)
> +++ mainboard/pcengines/alix1c/dts (working copy)
> @@ -37,5 +37,9 @@
> pcipath = "0xf,1";
> enabled;
> };
> + superio {
> + /config/("superio/winbond/w83627hf");
> + com1enable = "1";
> + };
> };
> };
> Index: mainboard/pcengines/alix1c/Makefile
> ===================================================================
> --- mainboard/pcengines/alix1c/Makefile (revision 524)
> +++ mainboard/pcengines/alix1c/Makefile (working copy)
> @@ -21,9 +21,8 @@
>
> STAGE0_MAINBOARD_OBJ := $(obj)/mainboard/$(MAINBOARDDIR)/stage1.o
>
> -INITRAM_OBJ = $(obj)/mainboard/$(MAINBOARDDIR)/initram.o \
> +INITRAM_OBJ = $(obj)/mainboard/$(MAINBOARDDIR)/initram.o \
>
Any reason for an extra space?
> $(obj)/northbridge/amd/geodelx/raminit.o \
> - $(obj)/southbridge/amd/cs5536/smbus_initram.o \
> $(obj)/arch/x86/geodelx/geodelx.o
>
> STAGE2_MAINBOARD_OBJ =
>
-Corey
More information about the coreboot
mailing list