[coreboot] [patch] ACPI on m57sli v1.0 - parport interrupt driven

[Andreas B. Mundt]

Hi,

>> So, I've added the missing ACPI part, but it seems that some more work is
>> needed to get parport interrupt driven working.
>I just did a mistake and set no address in the IO Section.
>
>There's already another patch on the list (which was filtered by my spam-filter, 
>and therefore I did the job again).
>The difference between my patch, and the one from Andreas are minimal, but I 
>added the ECP device which is necessary to get Parport full functional 
>(hopefully I did everything correct, as I can't test this without Parport 
>devices.)

my printer works fine (interrupt driven). From dmesg:

old dmesg:
	pnp: PnP ACPI init
	ACPI: bus type pnp registered
	pnp 00:00: parse allocated resources
	pnp 00:00:   add io  0xcf8-0xcff flags 0x1
	pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
	pnp 00:01: parse allocated resources
	pnp 00:01:   add io  0x60-0x60 flags 0x1
	pnp 00:01:   add io  0x64-0x64 flags 0x1
	pnp 00:01:   add irq 1 flags 0x1
	pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active)
	pnp 00:02: parse allocated resources
	pnp 00:02:   add io  0x378-0x387 flags 0x0
	pnp 00:02:   add irq 7 flags 0x1
	pnp 00:02: Plug and Play ACPI device, IDs PNP0400 (active)
	pnp 00:03: parse allocated resources
	pnp 00:03:   add io  0x60-0x60 flags 0x1
	pnp 00:03:   add io  0x64-0x64 flags 0x1
	pnp 00:03:   add irq 12 flags 0x1
	pnp 00:03: Plug and Play ACPI device, IDs PNP0f13 (active)
	pnp 00:04: parse allocated resources
	pnp 00:04:   add io  0x3f0-0x3f5 flags 0x1
	pnp 00:04:   add io  0x3f7-0x3f7 flags 0x1
	pnp 00:04:   add irq 6 flags 0x1
	pnp 00:04:   add dma 2 flags 0x0
	pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)
	pnp: PnP ACPI: found 5 devices

new dmesg:
	pnp: PnP ACPI init
	ACPI: bus type pnp registered
	pnp 00:00: parse allocated resources
	pnp 00:00:   add io  0xcf8-0xcff flags 0x1
	pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
	pnp 00:01: parse allocated resources
	pnp 00:01:   add io  0x60-0x60 flags 0x1
	pnp 00:01:   add io  0x64-0x64 flags 0x1
	pnp 00:01:   add irq 1 flags 0x1
	pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active)
	pnp 00:02: parse allocated resources
	pnp 00:02:   add io  0x60-0x60 flags 0x1
	pnp 00:02:   add io  0x64-0x64 flags 0x1
	pnp 00:02:   add irq 12 flags 0x1
	pnp 00:02: Plug and Play ACPI device, IDs PNP0f13 (active)
	pnp 00:03: parse allocated resources
	pnp 00:03:   add io  0x3f0-0x3f5 flags 0x1
	pnp 00:03:   add io  0x3f7-0x3f7 flags 0x1
	pnp 00:03:   add irq 6 flags 0x1
	pnp 00:03:   add dma 2 flags 0x0
	pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active)
	pnp 00:04: parse allocated resources
	pnp 00:04:   add io  0x378-0x37f flags 0x1
	pnp 00:04:   add irq 7 flags 0x1
	pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active)
	pnp 00:05: parse allocated resources
	pnp 00:05:   add io  0x378-0x37b flags 0x1
	pnp 00:05:   add io  0x778-0x77b flags 0x1
	pnp 00:05:   add irq 7 flags 0x1
	pnp 00:05:   add dma 0 flags 0x0
	pnp 00:05: Plug and Play ACPI device, IDs PNP0401 (active)
	pnp: PnP ACPI: found 6 devices

>
>The attached patch activates changes the LPT port from polling to interrupt-
>driven, and should be fine.
>
>Signed-off-by: Harald Gutmann <harald.gutmann at gmx.net>

Ignoring that I do not know how to check the ECP device:

Acked-by: Andreas B. Mundt <andi.mundt at web.de>

Kind regards,

     Andi