[coreboot] [v2] r4248 - in trunk/coreboot-v2/src/mainboard: rca/rm4100 thomson/ip1000

svn at coreboot.org svn at coreboot.org
Sat May 2 02:50:58 CEST 2009


Author: linux_junkie
Date: 2009-05-02 02:50:58 +0200 (Sat, 02 May 2009)
New Revision: 4248

Modified:
   trunk/coreboot-v2/src/mainboard/rca/rm4100/gpio.c
   trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c
Log:
Trivial fix up to the GPIO's connected to the IP1000 and RM4100, only set ones that are actually connected to something. 
Signed-off-by: Joseph Smith <joe at settoplinux.org> 
Acked-by: Joseph Smith <joe at settoplinux.org>

Modified: trunk/coreboot-v2/src/mainboard/rca/rm4100/gpio.c
===================================================================
--- trunk/coreboot-v2/src/mainboard/rca/rm4100/gpio.c	2009-05-01 14:33:19 UTC (rev 4247)
+++ trunk/coreboot-v2/src/mainboard/rca/rm4100/gpio.c	2009-05-02 00:50:58 UTC (rev 4248)
@@ -1,120 +1,143 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2008 Joseph Smith <joe at smittys.pointclark.net>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
- */
-
-#define PME_DEV			PNP_DEV(0x2e, 0x0a)
-#define PME_IO_BASE_ADDR	0x800      /* Runtime register base address */
-#define ICH_IO_BASE_ADDR	0x00000500 /* GPIO base address register */
-
-/* Early mainboard specific GPIO setup. */
-static void mb_gpio_init(void)
-{
-	device_t dev;
-	uint16_t port;
-	uint32_t set_gpio;
-
-	/* Southbridge GPIOs. */
-	/* Set the LPC device statically. */
-	dev = PCI_DEV(0x0, 0x1f, 0x0);
-
-	/* Set the value for GPIO base address register and enable GPIO. */
-	pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1));
-	pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10);
-
-	/* Set GPIO25 to input and drive GPIO23 to high,
-	 * this enables the LAN controller. 
-	 */
-	udelay(10);
-	set_gpio = 0x0000ffff;
-	set_gpio |= 1 << 25;
-	outl(set_gpio, ICH_IO_BASE_ADDR + 0x04);
-
-	set_gpio = 0x1b3f0000;
-	set_gpio |= 1 << 23;
-	outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c);
-
-	/* Super I/O GPIOs. */
-	dev = PME_DEV;
-	port = dev >> 8;
-
-	outb(0x55, port);		/* Enter the configuration state. */
-	pnp_set_logical_device(dev);
-	pnp_set_enable(dev, 0);
-	pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR);
-	pnp_set_enable(dev, 1);
-	outl(0x03, PME_IO_BASE_ADDR + 0x1e); /* Force Disk Change */
-	outl(0x02, PME_IO_BASE_ADDR + 0x1f); /* Floppy Data Rate */
-	outl(0x81, PME_IO_BASE_ADDR + 0x20); /* UART1 FIFO */
-	outl(0x00, PME_IO_BASE_ADDR + 0x21); /* UART2 FIFO */
-	outl(0x00, PME_IO_BASE_ADDR + 0x22); /* Device Disable */
-	outl(0x01, PME_IO_BASE_ADDR + 0x23); /* GP10 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x24); /* GP11 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x25); /* GP12 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x26); /* GP13 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x27); /* GP14 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x28); /* GP15 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x29); /* GP16 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x2a); /* GP17 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x2b); /* GP20 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x2c); /* GP21 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x2d); /* GP22 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x2f); /* GP24 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x30); /* GP25 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x31); /* GP26 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x32); /* GP27 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x33); /* GP30 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x34); /* GP31 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x35); /* GP32 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x36); /* GP33 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x37); /* GP34 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x38); /* GP35 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x39); /* GP36 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x3a); /* GP37 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x3b); /* GP40 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x3c); /* GP41 */
-	outl(0x86, PME_IO_BASE_ADDR + 0x3d); /* GP42 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x3e); /* GP43 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x3f); /* GP50 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x40); /* GP51 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x41); /* GP52 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x42); /* GP53 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x43); /* GP54 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x44); /* GP55 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x45); /* GP56 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x46); /* GP57 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x47); /* GP58 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x48); /* GP59 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x4b); /* GP1 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x4c); /* GP2 */
-	outl(0xc0, PME_IO_BASE_ADDR + 0x4d); /* GP3 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x4e); /* GP4 */
-	outl(0x07, PME_IO_BASE_ADDR + 0x4f); /* GP5 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x50); /* GP6 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x56); /* FAN1 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x57); /* FAN2 */
-	outl(0x50, PME_IO_BASE_ADDR + 0x58); /* Fan Control */
-	outl(0xff, PME_IO_BASE_ADDR + 0x59); /* Fan1 Tachometer */
-	outl(0xff, PME_IO_BASE_ADDR + 0x5a); /* Fan2 Tachometer */
-	outl(0x00, PME_IO_BASE_ADDR + 0x5b); /* Fan1 Preload */
-	outl(0x00, PME_IO_BASE_ADDR + 0x5c); /* Fan2 Preload */
-	outl(0x00, PME_IO_BASE_ADDR + 0x5d); /* LED1 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x5e); /* LED2 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x5f); /* Keyboard Scan Code */
-	outb(0xaa, port);		/* Exit the configuration state. */
-}
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Joseph Smith <joe at settoplinux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#define PME_DEV			PNP_DEV(0x2e, 0x0a)
+#define PME_IO_BASE_ADDR	0x800      /* Runtime register base address */
+#define ICH_IO_BASE_ADDR	0x00000500 /* GPIO base address register */
+
+/* Early mainboard specific GPIO setup. */
+static void mb_gpio_init(void)
+{
+	device_t dev;
+	uint16_t port;
+	uint32_t set_gpio;
+
+	/* Southbridge GPIOs. */
+	/* Set the LPC device statically. */
+	dev = PCI_DEV(0x0, 0x1f, 0x0);
+
+	/* Set the value for GPIO base address register and enable GPIO. */
+	pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1));
+	pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10);
+
+	/* Set GPIO23 to high, this enables the LAN controller. */
+	udelay(10);
+	set_gpio = inl(ICH_IO_BASE_ADDR + 0x0c);
+	set_gpio |= 1 << 23;
+	outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c);
+
+	/* Super I/O GPIOs. */
+	dev = PME_DEV;
+	port = dev >> 8;
+
+	/* Enter the configuration state. */
+	outb(0x55, port);
+	pnp_set_logical_device(dev);
+	pnp_set_enable(dev, 0);
+	pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR);
+	pnp_set_enable(dev, 1);
+
+	/* GP21 - LED_RED */
+	outl(0x01, PME_IO_BASE_ADDR + 0x2c);
+
+	/* GP30 - FAN2_TACH */
+	outl(0x05, PME_IO_BASE_ADDR + 0x33); 
+
+	/* GP31 - FAN1_TACH */
+	outl(0x05, PME_IO_BASE_ADDR + 0x34);
+
+	/* GP32 - FAN2_CTRL */
+	outl(0x04, PME_IO_BASE_ADDR + 0x35); 
+
+	/* GP33 - FAN1_CTRL */
+	outl(0x04, PME_IO_BASE_ADDR + 0x36);
+
+	/* GP34 - AUD_MUTE_OUT_R */
+	outl(0x00, PME_IO_BASE_ADDR + 0x37);
+
+	/* GP36 - KBRST */
+	outl(0x00, PME_IO_BASE_ADDR + 0x39);
+
+	/* GP37 - A20GATE */
+	outl(0x00, PME_IO_BASE_ADDR + 0x3a);
+
+	/* GP42 - GPIO_PME_OUT */
+	outl(0x00, PME_IO_BASE_ADDR + 0x3d); 
+
+	/* GP50 - SER2_RI */
+	outl(0x05, PME_IO_BASE_ADDR + 0x3f);
+
+	/* GP51 - SER2_DCD */
+	outl(0x05, PME_IO_BASE_ADDR + 0x40);
+
+	/* GP52 - SER2_RX */
+	outl(0x05, PME_IO_BASE_ADDR + 0x41);
+
+	/* GP53 - SER2_TX */
+	outl(0x04, PME_IO_BASE_ADDR + 0x42);
+
+	/* GP55 - SER2_RTS */
+	outl(0x04, PME_IO_BASE_ADDR + 0x44);
+
+	/* GP56 - SER2_CTS */
+	outl(0x05, PME_IO_BASE_ADDR + 0x45);
+
+	/* GP57 - SER2_DTR */
+	outl(0x04, PME_IO_BASE_ADDR + 0x46);
+
+	/* GP60 - LED_GREEN */
+	outl(0x01, PME_IO_BASE_ADDR + 0x47);
+
+	/* GP61 - LED_YELLOW */
+	outl(0x01, PME_IO_BASE_ADDR + 0x48);
+
+	/* GP3 */
+	outl(0xc0, PME_IO_BASE_ADDR + 0x4d);
+
+	/* GP4 */
+	outl(0x04, PME_IO_BASE_ADDR + 0x4e);
+
+	/* FAN1 */
+	outl(0x01, PME_IO_BASE_ADDR + 0x56);
+
+	/* FAN2 */
+	outl(0x01, PME_IO_BASE_ADDR + 0x57);
+
+	/* Fan Control */
+	outl(0x50, PME_IO_BASE_ADDR + 0x58);
+
+	/* Fan1 Tachometer */
+	outl(0xff, PME_IO_BASE_ADDR + 0x59);
+
+	/* Fan2 Tachometer */
+	outl(0xff, PME_IO_BASE_ADDR + 0x5a);
+
+	/* LED1 */
+	outl(0x00, PME_IO_BASE_ADDR + 0x5d);
+
+	/* LED2 */
+	outl(0x00, PME_IO_BASE_ADDR + 0x5e);
+
+	/* Keyboard Scan Code */
+	outl(0x00, PME_IO_BASE_ADDR + 0x5f);
+
+	/* Exit the configuration state. */
+	outb(0xaa, port);
+}

Modified: trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c
===================================================================
--- trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c	2009-05-01 14:33:19 UTC (rev 4247)
+++ trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c	2009-05-02 00:50:58 UTC (rev 4248)
@@ -1,120 +1,143 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2008 Joseph Smith <joe at settoplinux.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
- */
-
-#define PME_DEV			PNP_DEV(0x2e, 0x0a)
-#define PME_IO_BASE_ADDR	0x800      /* Runtime register base address */
-#define ICH_IO_BASE_ADDR	0x00000500 /* GPIO base address register */
-
-/* Early mainboard specific GPIO setup. */
-static void mb_gpio_init(void)
-{
-	device_t dev;
-	uint16_t port;
-	uint32_t set_gpio;
-
-	/* Southbridge GPIOs. */
-	/* Set the LPC device statically. */
-	dev = PCI_DEV(0x0, 0x1f, 0x0);
-
-	/* Set the value for GPIO base address register and enable GPIO. */
-	pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1));
-	pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10);
-
-	/* Set GPIO25 to input and drive GPIO23 to high,
-	 * this enables the LAN controller. 
-	 */
-	udelay(10);
-	set_gpio = 0x0000ffff;
-	set_gpio |= 1 << 25;
-	outl(set_gpio, ICH_IO_BASE_ADDR + 0x04);
-
-	set_gpio = 0x1b3f0000;
-	set_gpio |= 1 << 23;
-	outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c);
-
-	/* Super I/O GPIOs. */
-	dev = PME_DEV;
-	port = dev >> 8;
-
-	outb(0x55, port);		/* Enter the configuration state. */
-	pnp_set_logical_device(dev);
-	pnp_set_enable(dev, 0);
-	pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR);
-	pnp_set_enable(dev, 1);
-	outl(0x03, PME_IO_BASE_ADDR + 0x1e); /* Force Disk Change */
-	outl(0x02, PME_IO_BASE_ADDR + 0x1f); /* Floppy Data Rate */
-	outl(0x81, PME_IO_BASE_ADDR + 0x20); /* UART1 FIFO */
-	outl(0x81, PME_IO_BASE_ADDR + 0x21); /* UART2 FIFO */
-	outl(0x00, PME_IO_BASE_ADDR + 0x22); /* Device Disable */
-	outl(0x01, PME_IO_BASE_ADDR + 0x23); /* GP10 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x24); /* GP11 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x25); /* GP12 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x26); /* GP13 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x27); /* GP14 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x28); /* GP15 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x29); /* GP16 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x2a); /* GP17 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x2b); /* GP20 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x2c); /* GP21 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x2d); /* GP22 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x2f); /* GP24 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x30); /* GP25 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x31); /* GP26 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x32); /* GP27 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x33); /* GP30 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x34); /* GP31 */
-	outl(0x84, PME_IO_BASE_ADDR + 0x35); /* GP32 */
-	outl(0x84, PME_IO_BASE_ADDR + 0x36); /* GP33 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x37); /* GP34 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x38); /* GP35 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x39); /* GP36 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x3a); /* GP37 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x3b); /* GP40 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x3c); /* GP41 */
-	outl(0x86, PME_IO_BASE_ADDR + 0x3d); /* GP42 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x3e); /* GP43 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x3f); /* GP50 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x40); /* GP51 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x41); /* GP52 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x42); /* GP53 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x43); /* GP54 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x44); /* GP55 */
-	outl(0x05, PME_IO_BASE_ADDR + 0x45); /* GP56 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x46); /* GP57 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x47); /* GP58 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x48); /* GP59 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x4b); /* GP1 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x4c); /* GP2 */
-	outl(0xc0, PME_IO_BASE_ADDR + 0x4d); /* GP3 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x4e); /* GP4 */
-	outl(0x04, PME_IO_BASE_ADDR + 0x4f); /* GP5 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x50); /* GP6 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x56); /* FAN1 */
-	outl(0x01, PME_IO_BASE_ADDR + 0x57); /* FAN2 */
-	outl(0x58, PME_IO_BASE_ADDR + 0x58); /* Fan Control */
-	outl(0xff, PME_IO_BASE_ADDR + 0x59); /* Fan1 Tachometer */
-	outl(0x50, PME_IO_BASE_ADDR + 0x5a); /* Fan2 Tachometer */
-	outl(0x00, PME_IO_BASE_ADDR + 0x5b); /* Fan1 Preload */
-	outl(0x00, PME_IO_BASE_ADDR + 0x5c); /* Fan2 Preload */
-	outl(0x00, PME_IO_BASE_ADDR + 0x5d); /* LED1 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x5e); /* LED2 */
-	outl(0x00, PME_IO_BASE_ADDR + 0x5f); /* Keyboard Scan Code */
-	outb(0xaa, port);		/* Exit the configuration state. */
-}
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Joseph Smith <joe at settoplinux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#define PME_DEV			PNP_DEV(0x2e, 0x0a)
+#define PME_IO_BASE_ADDR	0x800      /* Runtime register base address */
+#define ICH_IO_BASE_ADDR	0x00000500 /* GPIO base address register */
+
+/* Early mainboard specific GPIO setup. */
+static void mb_gpio_init(void)
+{
+	device_t dev;
+	uint16_t port;
+	uint32_t set_gpio;
+
+	/* Southbridge GPIOs. */
+	/* Set the LPC device statically. */
+	dev = PCI_DEV(0x0, 0x1f, 0x0);
+
+	/* Set the value for GPIO base address register and enable GPIO. */
+	pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1));
+	pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10);
+
+	/* Set GPIO23 to high, this enables the LAN controller. */
+	udelay(10);
+	set_gpio = inl(ICH_IO_BASE_ADDR + 0x0c);
+	set_gpio |= 1 << 23;
+	outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c);
+
+	/* Super I/O GPIOs. */
+	dev = PME_DEV;
+	port = dev >> 8;
+
+	/* Enter the configuration state. */
+	outb(0x55, port);
+	pnp_set_logical_device(dev);
+	pnp_set_enable(dev, 0);
+	pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR);
+	pnp_set_enable(dev, 1);
+
+	/* GP21 - LED_RED */
+	outl(0x01, PME_IO_BASE_ADDR + 0x2c);
+
+	/* GP30 - FAN2_TACH */
+	outl(0x05, PME_IO_BASE_ADDR + 0x33); 
+
+	/* GP31 - FAN1_TACH */
+	outl(0x05, PME_IO_BASE_ADDR + 0x34);
+
+	/* GP32 - FAN2_CTRL */
+	outl(0x04, PME_IO_BASE_ADDR + 0x35); 
+
+	/* GP33 - FAN1_CTRL */
+	outl(0x04, PME_IO_BASE_ADDR + 0x36);
+
+	/* GP34 - AUD_MUTE_OUT_R */
+	outl(0x00, PME_IO_BASE_ADDR + 0x37);
+
+	/* GP36 - KBRST */
+	outl(0x00, PME_IO_BASE_ADDR + 0x39);
+
+	/* GP37 - A20GATE */
+	outl(0x00, PME_IO_BASE_ADDR + 0x3a);
+
+	/* GP42 - GPIO_PME_OUT */
+	outl(0x00, PME_IO_BASE_ADDR + 0x3d); 
+
+	/* GP50 - SER2_RI */
+	outl(0x05, PME_IO_BASE_ADDR + 0x3f);
+
+	/* GP51 - SER2_DCD */
+	outl(0x05, PME_IO_BASE_ADDR + 0x40);
+
+	/* GP52 - SER2_RX */
+	outl(0x05, PME_IO_BASE_ADDR + 0x41);
+
+	/* GP53 - SER2_TX */
+	outl(0x04, PME_IO_BASE_ADDR + 0x42);
+
+	/* GP55 - SER2_RTS */
+	outl(0x04, PME_IO_BASE_ADDR + 0x44);
+
+	/* GP56 - SER2_CTS */
+	outl(0x05, PME_IO_BASE_ADDR + 0x45);
+
+	/* GP57 - SER2_DTR */
+	outl(0x04, PME_IO_BASE_ADDR + 0x46);
+
+	/* GP60 - LED_GREEN */
+	outl(0x01, PME_IO_BASE_ADDR + 0x47);
+
+	/* GP61 - LED_YELLOW */
+	outl(0x01, PME_IO_BASE_ADDR + 0x48);
+
+	/* GP3 */
+	outl(0xc0, PME_IO_BASE_ADDR + 0x4d);
+
+	/* GP4 */
+	outl(0x04, PME_IO_BASE_ADDR + 0x4e);
+
+	/* FAN1 */
+	outl(0x01, PME_IO_BASE_ADDR + 0x56);
+
+	/* FAN2 */
+	outl(0x01, PME_IO_BASE_ADDR + 0x57);
+
+	/* Fan Control */
+	outl(0x50, PME_IO_BASE_ADDR + 0x58);
+
+	/* Fan1 Tachometer */
+	outl(0xff, PME_IO_BASE_ADDR + 0x59);
+
+	/* Fan2 Tachometer */
+	outl(0xff, PME_IO_BASE_ADDR + 0x5a);
+
+	/* LED1 */
+	outl(0x00, PME_IO_BASE_ADDR + 0x5d);
+
+	/* LED2 */
+	outl(0x00, PME_IO_BASE_ADDR + 0x5e);
+
+	/* Keyboard Scan Code */
+	outl(0x00, PME_IO_BASE_ADDR + 0x5f);
+
+	/* Exit the configuration state. */
+	outb(0xaa, port);
+}





More information about the coreboot mailing list