[coreboot] [patch]: it8718f, sometime we use 48Mhz.
Bao, Zheng
Zheng.Bao at amd.com
Mon May 11 05:15:05 CEST 2009
We should separate the it8718f_24mhz_clkin like the way 8712 does.
Signed-off-by: Zheng Bao <zheng.bao at amd.com>
Index: src/superio/ite/it8718f/it8718f_early_serial.c
===================================================================
--- src/superio/ite/it8718f/it8718f_early_serial.c (revision 449)
+++ src/superio/ite/it8718f/it8718f_early_serial.c (working copy)
@@ -45,10 +45,9 @@
outb(value, SIO_DATA);
}
-/* Enable the peripheral devices on the IT8718F Super I/O chip. */
-static void it8718f_enable_serial(device_t dev, unsigned iobase)
+static void it8718f_enter_conf(void)
{
- /* (1) Enter the configuration state (MB PnP mode). */
+ /* Enter the configuration state (MB PnP mode). */
/* Perform MB PnP setup to put the SIO chip at 0x2e. */
/* Base address 0x2e: 0x87 0x01 0x55 0x55. */
@@ -57,7 +56,30 @@
outb(0x01, IT8718F_CONFIGURATION_PORT);
outb(0x55, IT8718F_CONFIGURATION_PORT);
outb(0x55, IT8718F_CONFIGURATION_PORT);
+}
+static void it8718f_exit_conf(void)
+{
+ /* Exit the configuration state (MB PnP mode). */
+ it8718f_sio_write(0x00, IT8718F_CONFIG_REG_CC, 0x02);
+}
+
+static void it8718f_24mhz_clkin(void)
+{
+ it8718f_enter_conf();
+
+ /* Select 24MHz CLKIN (48MHZ default)*/
+ it8718f_sio_write(0x00, IT8718F_CONFIG_REG_CLOCKSEL, 0x1);
+
+ it8718f_exit_conf();
+}
+
+/* Enable the peripheral devices on the IT8718F Super I/O chip. */
+static void it8718f_enable_serial(device_t dev, unsigned iobase)
+{
+ /* (1) Enter the configuration state (MB PnP mode). */
+ it8718f_enter_conf();
+
/* (2) Modify the data of configuration registers. */
/* Select the chip to configure (if there's more than one).
@@ -65,17 +87,14 @@
If this register is not written, both chips are configured.
*/
/* it8718f_sio_write(0x00, IT8718F_CONFIG_REG_CONFIGSEL, 0x00);
*/
- /* Enable all devices. */
+ /* Enable serial port(s). */
it8718f_sio_write(IT8718F_SP1, 0x30, 0x1); /* Serial port 1 */
it8718f_sio_write(IT8718F_SP2, 0x30, 0x1); /* Serial port 2 */
- /* Select 24MHz CLKIN (set bit 0). */
- it8718f_sio_write(0x00, IT8718F_CONFIG_REG_CLOCKSEL, 0x01);
-
/* Clear software suspend mode (clear bit 0). TODO: Needed? */
/* it8718f_sio_write(0x00, IT8718F_CONFIG_REG_SWSUSP, 0x00); */
/* (3) Exit the configuration state (MB PnP mode). */
- it8718f_sio_write(0x00, IT8718F_CONFIG_REG_CC, 0x02);
+ it8718f_exit_conf();
}
-------------- next part --------------
A non-text attachment was scrubbed...
Name: it8718f_seperate_24Mhz_sel.patch
Type: application/octet-stream
Size: 2277 bytes
Desc: it8718f_seperate_24Mhz_sel.patch
URL: <http://www.coreboot.org/pipermail/coreboot/attachments/20090511/175f8bd8/attachment.obj>
More information about the coreboot
mailing list