[coreboot] flashrom touches only 0x70000-0x80000 addresses of my bios flash

Alexander Gordeev lasaine at lvk.cs.msu.su
Wed May 27 21:31:59 CEST 2009


On Tuesday 26 May 2009 03:56:49 Carl-Daniel Hailfinger wrote:
> Hi Alexander,
>
> On 24.05.2009 18:19, Alexander Gordeev wrote:
> > I've tried flashrom on my Gigabyte GA-K8N-SLI board but it can only write
> > to 0x70000-0x80000. This includes both write and erase.
>
> Did you test erase separately?
>
> If write/erase is only working on the top 64 kByte, we probably have to
> unlock the rest of the chip as well. Since our Pm49FL004 code already
> has unlocking routines, we probably need a board enable for you.
>
> Do you have a multimeter or continuity tester?
>
> > Could you please help me to solve this?
>
> We can try.
>
> > BTW, I don't yet have a backup chip so tested changes are
> > preferred :)
>
> Sure.
>
> > flashrom v0.9.0+r544
> > Found chipset "NVIDIA CK804", enabling flash write... OK.
> > Found chip "PMC Pm49FL004" (512 KB) at physical address 0xfff80000.
>
> The P49FL004 should be supported just fine. CK804 is OK as well.
> Definitely a board enable issue.

I'm sending you /proc/ioports and full dmesg as suggested on IRC.

I also found the SuperIO pin, which is connected to WE pin of flash: it is pin 
71, PSIN/GP45 as I've learned from the datasheet. However, I was only able to 
find it8712f datasheet which may be a bit different from it8712f-a.
You can obtain a foto of the chip from here: 
http://lvk.cs.msu.su/~lasaine/it8712f-a.png
The pin is marked.

I'll be happy to provide any additional information if needed.

-- 
  Alexander
-------------- next part --------------
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-15) (dannf at debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Thu Mar 26 01:08:11 UTC 2009
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
[    0.000000]  BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000d0000000 - 00000000e0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] 127MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] found SMP MP-table at [c00f5360] 000f5360
[    0.000000] Entering add_active_range(0, 0, 262128) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   262128
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   262128
[    0.000000] On node 0 totalpages: 262128
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 256 pages used for memmap
[    0.000000]   HighMem zone: 32496 pages, LIFO batch:7
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP 000F6CF0, 0014 (r0 Nvidia)
[    0.000000] ACPI: RSDT 3FFF3000, 0030 (r1 Nvidia AWRDACPI 42302E31 AWRD  1010101)
[    0.000000] ACPI: FACP 3FFF3040, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD  1010101)
[    0.000000] ACPI: DSDT 3FFF30C0, 4CD6 (r1 NVIDIA AWRDACPI     1000 MSFT  100000C)
[    0.000000] ACPI: FACS 3FFF0000, 0040
[    0.000000] ACPI: MCFG 3FFF7E40, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD  1010101)
[    0.000000] ACPI: APIC 3FFF7DC0, 007C (r1 Nvidia AWRDACPI 42302E31 AWRD  1010101)
[    0.000000] Nvidia board detected. Ignoring ACPI timer override.
[    0.000000] If you got timer trouble try acpi_use_timer_override
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: BIOS IRQ0 pin2 override ignored.
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:90000000)
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[    0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260080
[    0.000000] Kernel command line: root=/dev/sda3 ro 
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 2010.292 MHz processor.
[    0.004000] spurious 8259A interrupt: IRQ7.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Memory: 1028832k/1048512k available (1769k kernel code, 18964k reserved, 752k data, 244k init, 131008k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xfff4c000 - 0xfffff000   ( 716 kB)
[    0.004000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.004000]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[    0.004000]       .init : 0xc037f000 - 0xc03bc000   ( 244 kB)
[    0.004000]       .data : 0xc02ba4eb - 0xc0376620   ( 752 kB)
[    0.004000]       .text : 0xc0100000 - 0xc02ba4eb   (1769 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.084073] Calibrating delay using timer specific routine.. 4023.43 BogoMIPS (lpj=8046871)
[    0.084169] Security Framework initialized
[    0.084206] SELinux:  Disabled at boot.
[    0.084239] Capability LSM initialized
[    0.084284] Mount-cache hash table entries: 512
[    0.084450] Initializing cgroup subsys ns
[    0.084485] Initializing cgroup subsys cpuacct
[    0.084518] Initializing cgroup subsys devices
[    0.084567] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.084602] CPU: L2 Cache: 512K (64 bytes/line)
[    0.084636] CPU 0(2) -> Core 0
[    0.084668] Intel machine check architecture supported.
[    0.084702] Intel machine check reporting enabled on CPU#0.
[    0.084745] Checking 'hlt' instruction... OK.
[    0.101133] ACPI: Core revision 20080321
[    0.108894] ENABLING IO-APIC IRQs
[    0.109116] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[    0.152821] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
[    0.156009] Booting processor 1/1 ip 6000
[    0.164010] Initializing CPU#1
[    0.164010] Calibrating delay using timer specific routine.. 4020.86 BogoMIPS (lpj=8041728)
[    0.164010] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.164010] CPU: L2 Cache: 512K (64 bytes/line)
[    0.164010] CPU 1(2) -> Core 1
[    0.164010] Intel machine check architecture supported.
[    0.164010] Intel machine check reporting enabled on CPU#1.
[    0.243954] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
[    0.244015] Brought up 2 CPUs
[    0.244015] Total of 2 processors activated (8044.29 BogoMIPS).
[    0.244015] CPU0 attaching sched-domain:
[    0.244015]  domain 0: span 0-1
[    0.244015]   groups: 0 1
[    0.244015] CPU1 attaching sched-domain:
[    0.244015]  domain 0: span 0-1
[    0.244015]   groups: 1 0
[    0.244015] net_namespace: 660 bytes
[    0.244015] Booting paravirtualized kernel on bare hardware
[    0.244015] NET: Registered protocol family 16
[    0.244015] ACPI: bus type pci registered
[    0.244015] PCI: MCFG configuration 0: base d0000000 segment 0 buses 0 - 255
[    0.244015] PCI: MCFG area at d0000000 reserved in E820
[    0.244015] PCI: Using MMCONFIG for extended config space
[    0.244015] PCI: Using configuration type 1 for base access
[    0.244015] Setting up standard PCI resources
[    0.248015] ACPI: EC: Look up EC in DSDT
[    0.251110] ACPI Error (dsobject-0501): Package List length (6) larger than NumElements count (2), truncated
[    0.251178]  [20080321]
[    0.251277] ACPI Error (dsobject-0501): Package List length (6) larger than NumElements count (2), truncated
[    0.251343]  [20080321]
[    0.255007] ACPI: Interpreter enabled
[    0.255040] ACPI: (supports S0 S1 S4 S5)
[    0.255166] ACPI: Using IOAPIC for interrupt routing
[    0.264016] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.264016] PCI: Transparent bridge - 0000:00:09.0
[    0.264016] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.264016] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[    0.316019] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[    0.316019] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.316494] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[    0.319060] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.319531] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.320002] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[    0.320423] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.320895] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 9 10 11 *12 14 15)
[    0.321316] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[    0.321738] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.322164] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[    0.322589] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 11 *12 14 15)
[    0.323057] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.323536] ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[    0.323967] ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[    0.324395] ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.324886] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
[    0.325157] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[    0.325450] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0
[    0.325721] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[    0.325958] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[    0.326212] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
[    0.326555] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
[    0.326918] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
[    0.327257] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0
[    0.327597] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
[    0.327960] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
[    0.328299] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
[    0.328639] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[    0.329007] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[    0.329355] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
[    0.329702] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
[    0.330212] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.330212] pnp: PnP ACPI init
[    0.330212] ACPI: bus type pnp registered
[    0.338212] pnp: PnP ACPI: found 13 devices
[    0.338212] ACPI: ACPI bus type pnp unregistered
[    0.338212] PnPBIOS: Disabled by ACPI PNP
[    0.338212] PCI: Using ACPI for IRQ routing
[    0.345917] ACPI: RTC can wake from S4
[    0.349862] system 00:01: ioport range 0x1000-0x107f has been reserved
[    0.349898] system 00:01: ioport range 0x1080-0x10ff has been reserved
[    0.349934] system 00:01: ioport range 0x1400-0x147f has been reserved
[    0.349969] system 00:01: ioport range 0x1480-0x14ff has been reserved
[    0.350005] system 00:01: ioport range 0x1800-0x187f has been reserved
[    0.350040] system 00:01: ioport range 0x1880-0x18ff has been reserved
[    0.350080] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[    0.350115] system 00:02: ioport range 0x800-0x87f has been reserved
[    0.353847] system 00:02: ioport range 0x295-0x314 has been reserved
[    0.353847] system 00:02: ioport range 0x294-0x297 could not be reserved
[    0.353847] system 00:0b: iomem range 0xd0000000-0xdfffffff could not be reserved
[    0.353847] system 00:0c: iomem range 0xd0000-0xd3fff has been reserved
[    0.353847] system 00:0c: iomem range 0xd5800-0xd7fff has been reserved
[    0.353847] system 00:0c: iomem range 0xf0000-0xfbfff could not be reserved
[    0.353847] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved
[    0.353847] system 00:0c: iomem range 0x3fff0000-0x3fffffff could not be reserved
[    0.353847] system 00:0c: iomem range 0xffff0000-0xffffffff could not be reserved
[    0.353847] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[    0.353847] system 00:0c: iomem range 0x100000-0x3ffeffff could not be reserved
[    0.353847] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.353847] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
[    0.381848] PCI: Bridge: 0000:00:09.0
[    0.381897] Switched to high resolution mode on CPU 0
[    0.381899]   IO window: 9000-9fff
[    0.381933]   MEM window: disabled.
[    0.381965]   PREFETCH window: disabled.
[    0.381998] PCI: Bridge: 0000:00:0b.0
[    0.382031]   IO window: 6000-6fff
[    0.382063]   MEM window: disabled.
[    0.382095]   PREFETCH window: disabled.
[    0.382129] PCI: Bridge: 0000:00:0c.0
[    0.382161]   IO window: 8000-8fff
[    0.382193]   MEM window: disabled.
[    0.382225]   PREFETCH window: disabled.
[    0.382259] PCI: Bridge: 0000:00:0d.0
[    0.382291]   IO window: 7000-7fff
[    0.382323]   MEM window: disabled.
[    0.384730] Switched to high resolution mode on CPU 1
[    0.384717]   PREFETCH window: disabled.
[    0.384752] PCI: Bridge: 0000:00:0e.0
[    0.384785]   IO window: a000-afff
[    0.384818]   MEM window: 0xf0000000-0xf2ffffff
[    0.384851]   PREFETCH window: 0x00000000e0000000-0x00000000efffffff
[    0.384891] PCI: Setting latency timer of device 0000:00:09.0 to 64
[    0.384899] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[    0.384905] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[    0.384911] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[    0.384918] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[    0.384987] NET: Registered protocol family 2
[    0.396294] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.396679] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.397432] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.397860] TCP: Hash tables configured (established 131072 bind 65536)
[    0.397896] TCP reno registered
[    0.404302] NET: Registered protocol family 1
[    0.404448] checking if image is initramfs... it is
[    0.928467] Freeing initrd memory: 6628k freed
[    0.928824] audit: initializing netlink socket (disabled)
[    0.928878] type=2000 audit(1243458807.920:1): initialized
[    0.932465] highmem bounce pool size: 64 pages
[    0.932465] Total HugeTLB memory allocated, 0
[    0.932465] VFS: Disk quotas dquot_6.5.1
[    0.932465] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.932465] msgmni has been set to 1767
[    0.932465] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.932465] io scheduler noop registered
[    0.932465] io scheduler anticipatory registered
[    0.932465] io scheduler deadline registered
[    0.932465] io scheduler cfq registered (default)
[    0.932465] pci 0000:00:00.0: Enabling HT MSI Mapping
[    0.956532] pci 0000:00:0b.0: Enabling HT MSI Mapping
[    0.956571] pci 0000:00:0b.0: Found enabled HT MSI Mapping
[    0.956607] pci 0000:00:0b.0: Linking AER extended capability
[    0.956649] pci 0000:00:0c.0: Enabling HT MSI Mapping
[    0.956687] pci 0000:00:0c.0: Found enabled HT MSI Mapping
[    0.956722] pci 0000:00:0c.0: Linking AER extended capability
[    0.956763] pci 0000:00:0d.0: Enabling HT MSI Mapping
[    0.956800] pci 0000:00:0d.0: Found enabled HT MSI Mapping
[    0.956835] pci 0000:00:0d.0: Linking AER extended capability
[    0.956876] pci 0000:00:0e.0: Enabling HT MSI Mapping
[    0.956914] pci 0000:00:0e.0: Found enabled HT MSI Mapping
[    0.956948] pci 0000:00:0e.0: Linking AER extended capability
[    0.956998] pci 0000:05:00.0: Boot video device
[    0.957107] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[    0.957129] assign_interrupt_mode Found MSI capability
[    0.957178] Allocate Port Service[0000:00:0b.0:pcie00]
[    0.957235] Allocate Port Service[0000:00:0b.0:pcie03]
[    0.959660] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[    0.959660] assign_interrupt_mode Found MSI capability
[    0.959660] Allocate Port Service[0000:00:0c.0:pcie00]
[    0.959660] Allocate Port Service[0000:00:0c.0:pcie03]
[    0.959660] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[    0.959660] assign_interrupt_mode Found MSI capability
[    0.959660] Allocate Port Service[0000:00:0d.0:pcie00]
[    0.959660] Allocate Port Service[0000:00:0d.0:pcie03]
[    0.959660] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[    0.959660] assign_interrupt_mode Found MSI capability
[    0.959660] Allocate Port Service[0000:00:0e.0:pcie00]
[    0.959660] Allocate Port Service[0000:00:0e.0:pcie03]
[    0.959660] isapnp: Scanning for PnP cards...
[    1.311621] isapnp: No Plug & Play device found
[    1.313545] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    1.313545] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.313545] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.317529] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.317529] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.317529] brd: module loaded
[    1.317529] PNP: No PS/2 controller found. Probing ports directly.
[    1.570041] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.572533] mice: PS/2 mouse device common for all mice
[    1.572533] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    1.572533] rtc0: alarms up to one year, y3k
[    1.572533] cpuidle: using governor ladder
[    1.572533] cpuidle: using governor menu
[    1.572533] No iBFT detected.
[    1.572927] TCP cubic registered
[    1.572961] NET: Registered protocol family 17
[    1.572997] Using IPI No-Shortcut mode
[    1.573529] registered taskstats version 1
[    1.573529] rtc_cmos 00:04: setting system clock to 2009-05-27 21:13:28 UTC (1243458808)
[    1.573529] Freeing unused kernel memory: 244k freed
[    1.745514] ACPI: ACPI0007:00 is registered as cooling_device0
[    1.745514] ACPI: ACPI0007:01 is registered as cooling_device1
[    1.910678] usbcore: registered new interface driver usbfs
[    1.910745] usbcore: registered new interface driver hub
[    1.910828] usbcore: registered new device driver usb
[    1.917288] Uniform Multi-Platform E-IDE driver
[    1.917288] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    1.921288] NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
[    1.921288] NFORCE-CK804: IDE controller (0x10de:0x0053 rev 0xf2) at  PCI slot 0000:00:06.0
[    1.921288] NFORCE-CK804: not 100% native mode: will probe irqs later
[    1.921288]     ide0: BM-DMA at 0xf000-0xf007
[    1.921288]     ide1: BM-DMA at 0xf008-0xf00f
[    1.921288] Probing IDE interface ide0...
[    1.933203] No dock devices found.
[    1.941203] SCSI subsystem initialized
[    1.957209] libata version 3.00 loaded.
[    1.961286] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.653365] hda: _NEC DVD_RW ND-4551A, ATAPI CD/DVD-ROM drive
[    3.325333] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[    3.325485] hda: UDMA/33 mode selected
[    3.325656] Probing IDE interface ide1...
[    4.278018] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[    4.278018] ide1 at 0x170-0x177,0x376 on irq 15
[    4.278018] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
[    4.278018] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23
[    4.278018] PCI: Setting latency timer of device 0000:00:02.0 to 64
[    4.278018] ohci_hcd 0000:00:02.0: OHCI Host Controller
[    4.278018] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[    4.278018] ohci_hcd 0000:00:02.0: irq 23, io mem 0xf3004000
[    4.335321] usb usb1: configuration #1 chosen from 1 choice
[    4.335381] hub 1-0:1.0: USB hub found
[    4.335420] hub 1-0:1.0: 10 ports detected
[    4.437363] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    4.437399] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.437441] usb usb1: Product: OHCI Host Controller
[    4.437475] usb usb1: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[    4.437509] usb usb1: SerialNumber: 0000:00:02.0
[    4.437475] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
[    4.437475] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 22 (level, low) -> IRQ 22
[    4.437475] PCI: Setting latency timer of device 0000:00:02.1 to 64
[    4.437475] ehci_hcd 0000:00:02.1: EHCI Host Controller
[    4.437475] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
[    4.437475] ehci_hcd 0000:00:02.1: debug port 1
[    4.437475] PCI: cache line size of 64 is not supported by device 0000:00:02.1
[    4.437475] ehci_hcd 0000:00:02.1: irq 22, io mem 0xfeb00000
[    4.493472] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    4.493472] usb usb2: configuration #1 chosen from 1 choice
[    4.493472] hub 2-0:1.0: USB hub found
[    4.493472] hub 2-0:1.0: 10 ports detected
[    4.593555] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    4.593591] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.593634] usb usb2: Product: EHCI Host Controller
[    4.593667] usb usb2: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[    4.593701] usb usb2: SerialNumber: 0000:00:02.1
[    4.597473] sata_nv 0000:00:07.0: version 3.5
[    4.597473] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
[    4.597473] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 21 (level, low) -> IRQ 21
[    4.597473] PCI: Setting latency timer of device 0000:00:07.0 to 64
[    4.597473] scsi0 : sata_nv
[    4.597473] scsi1 : sata_nv
[    4.597473] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xcc00 irq 21
[    4.597473] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xcc08 irq 21
[    5.079853] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    5.088023] ata1.00: HPA detected: current 488395055, native 488397168
[    5.088061] ata1.00: ATA-7: SAMSUNG SP2504C, VT100-33, max UDMA7
[    5.088096] ata1.00: 488395055 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    5.096029] ata1.00: configured for UDMA/133
[    5.427838] ata2: SATA link down (SStatus 0 SControl 300)
[    5.431827] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG SP2504C  VT10 PQ: 0 ANSI: 5
[    5.431827] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
[    5.431827] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 20 (level, low) -> IRQ 20
[    5.431827] PCI: Setting latency timer of device 0000:00:08.0 to 64
[    5.431827] scsi2 : sata_nv
[    5.431827] scsi3 : sata_nv
[    5.431827] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe000 irq 20
[    5.431827] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe008 irq 20
[    5.475826] usb 2-7: new high speed USB device using ehci_hcd and address 3
[    5.608142] usb 2-7: configuration #1 chosen from 1 choice
[    5.608240] hub 2-7:1.0: USB hub found
[    5.608341] hub 2-7:1.0: 4 ports detected
[    5.792144] usb 2-7: New USB device found, idVendor=0424, idProduct=2504
[    5.792180] usb 2-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.835061] ata3: SATA link down (SStatus 0 SControl 300)
[    6.156525] ata4: SATA link down (SStatus 0 SControl 300)
[    6.169505] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[    6.169505] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
[    6.169505] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 23
[    6.169505] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[    6.589335] usb 1-1: new low speed USB device using ohci_hcd and address 2
[    7.059012] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x3f1 @ 7, addr 00:14:85:38:62:13
[    7.059058] forcedeth 0000:00:0a.0: highdma csum timirq gbit lnktim desc-v3
[    7.072005] usb 1-1: configuration #1 chosen from 1 choice
[    7.076843] usb 1-1: New USB device found, idVendor=0c16, idProduct=0002
[    7.076843] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    7.076843] usb 1-1: Product: Gyration RF Technology Receiver
[    7.076843] usb 1-1: Manufacturer: Gyration
[    7.079378] hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[    7.079540] Uniform CD-ROM driver Revision: 3.20
[    7.084010] Driver 'sd' needs updating - please use bus_type methods
[    7.084010] sd 0:0:0:0: [sda] 488395055 512-byte hardware sectors (250058 MB)
[    7.084010] sd 0:0:0:0: [sda] Write Protect is off
[    7.084010] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    7.084010] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    7.084010] sd 0:0:0:0: [sda] 488395055 512-byte hardware sectors (250058 MB)
[    7.084010] sd 0:0:0:0: [sda] Write Protect is off
[    7.084010] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    7.084010] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    7.084010]  sda: sda1 sda2 sda3 sda4
[    7.102955] sd 0:0:0:0: [sda] Attached SCSI disk
[    7.425705] usb 1-8: new low speed USB device using ohci_hcd and address 3
[    7.628112] usb 1-8: configuration #1 chosen from 1 choice
[    7.638308] usb 1-8: New USB device found, idVendor=062a, idProduct=0201
[    7.638348] usb 1-8: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    7.638384] usb 1-8: Product: USB-compliant keyboard
[    8.115916] usb 1-10: new low speed USB device using ohci_hcd and address 4
[    8.319907] usb 1-10: configuration #1 chosen from 1 choice
[    8.492903] usb 1-10: New USB device found, idVendor=04f3, idProduct=0212
[    8.492943] usb 1-10: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    8.492985] usb 1-10: Product: PS/2+USB Mouse
[    8.498972] usbcore: registered new interface driver hiddev
[    8.508903] input: Gyration Gyration RF Technology Receiver as /class/input/input0
[    8.508957] input,hiddev96,hidraw0: USB HID v1.10 Keyboard [Gyration Gyration RF Technology Receiver] on usb-0000:00:02.0-1
[    8.522679] input: Gyration Gyration RF Technology Receiver as /class/input/input1
[    8.522742] input,hiddev97,hidraw1: USB HID v1.20 Mouse [Gyration Gyration RF Technology Receiver] on usb-0000:00:02.0-1
[    8.533121] input: USB-compliant keyboard as /class/input/input2
[    8.534644] input,hidraw2: USB HID v1.10 Keyboard [USB-compliant keyboard] on usb-0000:00:02.0-8
[    8.544204] input: USB-compliant keyboard as /class/input/input3
[    8.544204] input,hiddev98,hidraw3: USB HID v1.10 Mouse [USB-compliant keyboard] on usb-0000:00:02.0-8
[    8.550388] input: PS/2+USB Mouse as /class/input/input4
[    8.550388] input,hidraw4: USB HID v1.11 Mouse [PS/2+USB Mouse] on usb-0000:00:02.0-10
[    8.550388] usbcore: registered new interface driver usbhid
[    8.550388] usbhid: v2.6:USB HID core driver
[    8.673682] PM: Starting manual resume from disk
[    8.679444] ReiserFS: sda3: found reiserfs format "3.6" with standard journal
[    8.679444] ReiserFS: sda3: using ordered data mode
[    8.690372] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[    8.690948] ReiserFS: sda3: checking transaction log (sda3)
[   14.242261] ReiserFS: sda3: replayed 105 transactions in 5 seconds
[   14.245890] ReiserFS: sda3: Using r5 hash to sort names
[   16.251848] udev: starting version 141
[   16.251848] udev: deprecated sysfs layout; update the kernel or disable CONFIG_SYSFS_DEPRECATED; some udev features will not work correctly
[   16.815849] input: Power Button (FF) as /class/input/input5
[   16.823849] ACPI: Power Button (FF) [PWRF]
[   16.823849] input: Power Button (CM) as /class/input/input6
[   16.831849] ACPI: Power Button (CM) [PWRB]
[   16.839213] parport_pc 00:0a: reported by Plug and Play ACPI
[   16.839289] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   17.006698] input: PC Speaker as /class/input/input7
[   17.576062] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00
[   17.576062] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c40
[   17.869358] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
[   17.869358] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, low) -> IRQ 22
[   17.869358] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   18.197172] intel8x0_measure_ac97_clock: measured 53707 usecs
[   18.197211] intel8x0: clocking to 46872
[   18.202166] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[   18.202166] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
[   18.258160] juli@: analog I/O detected
[   18.939989] Adding 1461904k swap on /dev/sda2.  Priority:-1 extents:1 across:1461904k
[   19.963031] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
[   19.963031] ide_generic: I/O resource 0x1F0-0x1F7 not free.
[   19.963031] ide_generic: I/O resource 0x170-0x177 not free.
[   20.104547] fuse init (API version 7.9)
[   22.162650] NET: Registered protocol family 10
[   22.163199] lo: Disabled Privacy Extensions
[   22.835665] RPC: Registered udp transport module.
[   22.835665] RPC: Registered tcp transport module.
[   31.156010] Bluetooth: Core ver 2.11
[   31.156010] NET: Registered protocol family 31
[   31.156010] Bluetooth: HCI device and connection manager initialized
[   31.156010] Bluetooth: HCI socket layer initialized
[   31.247158] Bluetooth: L2CAP ver 2.9
[   31.247158] Bluetooth: L2CAP socket layer initialized
[   31.323163] Bluetooth: RFCOMM socket layer initialized
[   31.323163] Bluetooth: RFCOMM TTY layer initialized
[   31.323163] Bluetooth: RFCOMM ver 1.8
[   32.875803] eth0: no IPv6 routers present
[   36.257263] Linux agpgart interface v0.103
[   36.497742] nvidia: module license 'NVIDIA' taints kernel.
[   36.750848] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[   36.750848] ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
[   36.750867] PCI: Setting latency timer of device 0000:05:00.0 to 64
[   36.751104] NVRM: loading NVIDIA UNIX x86 Kernel Module  173.14.09  Wed Jun  4 23:43:17 PDT 2008
-------------- next part --------------
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0073 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:06.0
  0170-0177 : NFORCE-CK804
01f0-01f7 : 0000:00:06.0
  01f0-01f7 : NFORCE-CK804
0295-0314 : pnp 00:02
  02f8-02ff : serial
0376-0376 : 0000:00:06.0
  0376-0376 : NFORCE-CK804
0378-037a : parport0
03c0-03df : vga+
03f6-03f6 : 0000:00:06.0
  03f6-03f6 : NFORCE-CK804
03f8-03ff : serial
04d0-04d1 : pnp 00:02
0800-087f : pnp 00:02
0960-0967 : 0000:00:08.0
  0960-0967 : sata_nv
0970-0977 : 0000:00:07.0
  0970-0977 : sata_nv
09e0-09e7 : 0000:00:08.0
  09e0-09e7 : sata_nv
09f0-09f7 : 0000:00:07.0
  09f0-09f7 : sata_nv
0b60-0b63 : 0000:00:08.0
  0b60-0b63 : sata_nv
0b70-0b73 : 0000:00:07.0
  0b70-0b73 : sata_nv
0be0-0be3 : 0000:00:08.0
  0be0-0be3 : sata_nv
0bf0-0bf3 : 0000:00:07.0
  0bf0-0bf3 : sata_nv
0cf8-0cff : PCI conf1
1000-107f : pnp 00:01
  1000-1003 : ACPI PM1a_EVT_BLK
  1004-1005 : ACPI PM1a_CNT_BLK
  1008-100b : ACPI PM_TMR
  101c-101c : ACPI PM2_CNT_BLK
  1020-1027 : ACPI GPE0_BLK
1080-10ff : pnp 00:01
1400-147f : pnp 00:01
1480-14ff : pnp 00:01
  14a0-14af : ACPI GPE1_BLK
1800-187f : pnp 00:01
1880-18ff : pnp 00:01
1c00-1c3f : 0000:00:01.1
  1c00-1c3f : nForce2_smbus
1c40-1c7f : 0000:00:01.1
  1c40-1c7f : nForce2_smbus
6000-6fff : PCI Bus 0000:02
7000-7fff : PCI Bus 0000:04
8000-8fff : PCI Bus 0000:03
9000-9fff : PCI Bus 0000:01
  9000-901f : 0000:01:08.0
    9000-901f : ICE1724
  9400-947f : 0000:01:08.0
    9400-947f : ICE1724
a000-afff : PCI Bus 0000:05
  a000-a07f : 0000:05:00.0
b400-b4ff : 0000:00:04.0
  b400-b4ff : NVidia CK804
b800-b8ff : 0000:00:04.0
  b800-b8ff : NVidia CK804
cc00-cc0f : 0000:00:07.0
  cc00-cc0f : sata_nv
e000-e00f : 0000:00:08.0
  e000-e00f : sata_nv
e400-e41f : 0000:00:01.1
e800-e807 : 0000:00:0a.0
  e800-e807 : forcedeth
f000-f00f : 0000:00:06.0
  f000-f00f : NFORCE-CK804


More information about the coreboot mailing list