No subject
Sun Dec 9 17:34:17 CET 2012
around 7 seconds. I've got access to device programmers and 2m repair
stuff, so flashing isn't a huge issue.
Would this be a good board for a proof of concept, or should I look at
something else.
The board is a Kino LX800, AMD GEODE 500mhz, sata/pata, onboard amd
video, onboard realtek 8139 ethernet.
I'd like to to LB and kernel in flash, but if the hardware won't suppor
a 16mbit flash, then I'll do lb/filo and boot from CF over the standard
ide channel. The board currently has a 49fl004 socketed flash. Plan on
using a stripped down debian install, since that's the only one I can
reliably shrink.
Thanks,
Mark
Here's all the specs:
http://tinyurl.com/3ajv9l
Here's the output of lspci.
00:01.0 Host bridge: Advanced Micro Devices [AMD] Unknown device 2080
(rev 31)
00:01.1 VGA compatible controller: Advanced Micro Devices [AMD] Geode LX
Video
00:01.2 Entertainment encryption device: Advanced Micro Devices [AMD]
Geode LX AES Security Block
00:0e.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
00:0f.0 ISA bridge: Advanced Micro Devices [AMD] CS5536 [Geode
companion] ISA (rev 03)
00:0f.2 IDE interface: Advanced Micro Devices [AMD] CS5536 [Geode
companion] IDE (rev 01)
00:0f.3 Multimedia audio controller: Advanced Micro Devices [AMD] CS5536
[Geode companion] Audio (rev 01)
00:0f.4 USB Controller: Advanced Micro Devices [AMD] CS5536 [Geode
companion] OHC (rev 02)
00:0f.5 USB Controller: Advanced Micro Devices [AMD] CS5536 [Geode
companion] EHC (rev 02)
00:10.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
00:11.0 Mass storage controller: ALi Corporation ALi M5281 Serial ATA /
RAID Host Controller (rev a4)
00:11.1 Mass storage controller: ALi Corporation M5228 ALi ATA/RAID
Controller (rev c6)
00:12.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Here's the more verbose lspci output recommend by the guys on irc.
00:01.0 0600: 1022:2080 (rev 31)
Subsystem: 1022:2080
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248, Cache Line Size: 32 bytes
Region 0: I/O ports at ac1c [size=4]
Region 1: I/O ports at 9e00 [size=8]
00: 22 10 80 20 05 00 20 02 31 00 00 06 08 f8 80 00
10: 1d ac 00 00 01 9e 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 80 20
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:01.1 0300: 1022:2081
Subsystem: 1022:2081
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at efff4000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at efff0000 (32-bit, non-prefetchable) [size=16K]
Region 3: Memory at effec000 (32-bit, non-prefetchable) [size=16K]
Region 4: Memory at effe8000 (32-bit, non-prefetchable) [size=16K]
00: 22 10 81 20 07 00 20 02 00 00 00 03 08 00 00 00
10: 00 00 00 ee 00 40 ff ef 00 00 ff ef 00 c0 fe ef
20: 00 80 fe ef 00 00 00 00 00 00 00 00 22 10 81 20
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
00:01.2 1010: 1022:2082
Subsystem: 1022:2082
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at effe4000 (32-bit, non-prefetchable) [size=16K]
00: 22 10 82 20 06 00 a0 02 00 00 10 10 08 00 00 00
10: 00 40 fe ef 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 82 20
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
00:0e.0 0200: 10ec:8139 (rev 10)
Subsystem: 10ec:8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at f200 [size=256]
Region 1: Memory at effff000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: ec 10 39 81 07 00 90 82 10 00 00 02 00 20 00 00
10: 01 f2 00 00 00 f0 ff ef 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 39 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 20 40
00:0f.0 0601: 1022:2090 (rev 03)
Subsystem: 1022:2090
Control: I/O+ Mem- BusMaster- SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 6000 [size=8]
Region 1: I/O ports at 6100 [size=256]
Region 2: I/O ports at 6200 [size=64]
Region 3: I/O ports at 1000 [size=32]
Region 4: I/O ports at 9d00 [size=128]
Region 5: I/O ports at 9c00 [size=64]
00: 22 10 90 20 09 00 a0 02 03 00 01 06 08 40 80 00
10: 01 60 00 00 01 61 00 00 01 62 00 00 01 10 00 00
20: 01 9d 00 00 01 9c 00 00 00 00 00 00 22 10 90 20
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0f.2 0101: 1022:209a (rev 01) (prog-if 80)
Subsystem: 1022:209a
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248, Cache Line Size: 32 bytes
Region 0: [virtual] Memory at 000001f0 (32-bit,
non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3,
non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit,
non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3,
non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at ff00 [size=16]
00: 22 10 9a 20 05 00 a0 02 01 80 01 01 08 f8 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 ff 00 00 00 00 00 00 00 00 00 00 22 10 9a 20
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0f.3 0401: 1022:2093 (rev 01)
Subsystem: 1022:2093
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at fe00 [size=128]
00: 22 10 93 20 05 00 a0 02 01 00 01 04 08 00 00 00
10: 01 fe 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 93 20
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00
00:0f.4 0c03: 1022:2094 (rev 02) (prog-if 10)
Subsystem: 1022:2094
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 11
Region 0: Memory at efffe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 22 10 94 20 06 00 30 02 02 10 03 0c 08 00 00 00
10: 00 e0 ff ef 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 94 20
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 04 00 00
00:0f.5 0c03: 1022:2095 (rev 02) (prog-if 20)
Subsystem: 1022:2095
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 11
Region 0: Memory at efffd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 22 10 95 20 06 00 30 02 02 20 03 0c 08 00 00 00
10: 00 d0 ff ef 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 95 20
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 04 00 00
00:10.0 0200: 10ec:8139 (rev 10)
Subsystem: 10ec:8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at f000 [size=256]
Region 1: Memory at efffc000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: ec 10 39 81 07 00 90 02 10 00 00 02 00 20 00 00
10: 01 f0 00 00 00 c0 ff ef 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 39 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 20 40
00:11.0 0180: 10b9:5281 (rev a4) (prog-if 85)
Subsystem: 10b9:5281
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128, Cache Line Size: 512 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at fd00 [size=8]
Region 1: I/O ports at fc00 [size=4]
Region 2: I/O ports at fb00 [size=8]
Region 3: I/O ports at fa00 [size=4]
Region 4: I/O ports at f900 [size=16]
[virtual] Expansion ROM at 20000000 [disabled] [size=64K]
00: b9 10 81 52 05 00 a0 02 a4 85 80 01 80 80 80 00
10: 01 fd 00 00 01 fc 00 00 01 fb 00 00 01 fa 00 00
20: 01 f9 00 00 00 00 00 00 00 00 00 00 b9 10 81 52
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
00:11.1 0180: 10b9:5228 (rev c6) (prog-if 85)
Subsystem: 10b9:5281
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at f800 [size=8]
Region 1: I/O ports at f700 [size=4]
Region 2: I/O ports at f600 [size=8]
Region 3: I/O ports at f500 [size=4]
Region 4: I/O ports at f400 [size=16]
00: b9 10 28 52 05 00 a0 02 c6 85 80 01 00 80 80 00
10: 01 f8 00 00 01 f7 00 00 01 f6 00 00 01 f5 00 00
20: 01 f4 00 00 00 00 00 00 a0 00 00 00 b9 10 81 52
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
00:12.0 0200: 10ec:8139 (rev 10)
Subsystem: 10ec:8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ee00 [size=256]
Region 1: Memory at efffb000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 20010000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: ec 10 39 81 07 00 90 02 10 00 00 02 00 20 00 00
10: 01 ee 00 00 00 b0 ff ef 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 39 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 20 40
More information about the coreboot
mailing list