LinuxBIOS-1.1.7.0Fallback Fri Sep 30 13:08:05 CST 2005 starting... setting up resource map....done. 01 nodes initialized. ht reset - LinuxBIOS-1.1.7.0Fallback Fri Sep 30 13:08:05 CST 2005 starting... setting up resource map....done. 01 nodes initialized. Ram1.00 Ram1.01 Ram2.00 Ram2.01 No memory controller present Ram3 Initializing memory: done Clearing initial memory region: done Ram4 Copying LinuxBIOS to ram. Jumping to LinuxBIOS. LinuxBIOS-1.1.7.0Fallback Fri Sep 30 13:08:05 CST 2005 booting... Enumerating buses... APIC_CLUSTER: 0 enabled PCI_DOMAIN: 0000 enabled CPU: APIC: 00 enabled CPU: APIC: 01 enabled PCI: pci_scan_bus for bus 0 PCI: 00:18.0 [1022/1100] bus ops PCI: 00:18.0 [1022/1100] enabled PCI: 00:18.1 [1022/1101] enabled PCI: 00:18.2 [1022/1102] enabled PCI: 00:18.3 [1022/1103] ops PCI: 00:18.3 [1022/1103] enabled Disabling static device: PCI: 00:19.0 PCI: 00:19.0 No device operations Disabling static device: PCI: 00:19.1 PCI: 00:19.1 No device operations Disabling static device: PCI: 00:19.2 PCI: 00:19.2 No device operations Disabling static device: PCI: 00:19.3 PCI: 00:19.3 No device operations PCI: 01:01.0 [1022/7450] enabled next_unitid: 0003 PCI: 01:03.0 [1022/7460] enabled next_unitid: 0007 PCI: pci_scan_bus for bus 1 PCI: 01:01.0 [1022/7450] bus ops PCI: 01:01.0 [1022/7450] enabled PCI: 01:01.1 [1022/7451] ops PCI: 01:01.1 [1022/7451] enabled PCI: 01:02.0 [1022/7450] bus ops PCI: 01:02.0 [1022/7450] enabled PCI: 01:02.1 [1022/7451] ops PCI: 01:02.1 [1022/7451] enabled PCI: 01:03.0 [1022/7460] bus ops PCI: 01:03.0 [1022/7460] enabled PCI: 01:04.0 [1022/7468] bus ops PCI: 01:04.0 [1022/7468] enabled PCI: 01:04.1 [1022/7469] ops PCI: 01:04.1 [1022/7469] enabled PCI: 01:04.2 [1022/746a] bus ops PCI: 01:04.2 [1022/746a] enabled PCI: 01:04.3 [1022/746b] bus ops PCI: 01:04.3 [1022/746b] enabled PCI: 01:04.5 No device operations PCI: 01:04.6 [1022/746e] enabled PCI: pci_scan_bus for bus 2 PCI: 02:03.0 [14e4/16a6] enabled PCI: 02:04.0 [14e4/16a6] enabled PCI: pci_scan_bus returning with max=02 PCI: pci_scan_bus for bus 3 PCI: pci_scan_bus returning with max=03 PCI: pci_scan_bus for bus 4 PCI: 04:00.0 [1022/7464] enabled PCI: 04:00.1 [1022/7464] enabled PCI: 04:00.2 No device operations PCI: 04:01.0 No device operations PCI: 04:06.0 [1002/4752] enabled PCI: pci_scan_bus returning with max=04 PNP: 002e.0 disabled PNP: 002e.1 disabled PNP: 002e.2 disabled PNP: 002e.3 enabled PNP: 002e.4 disabled PNP: 002e.5 disabled PNP: 002e.6 enabled PNP: 002e.7 disabled PNP: 002e.8 disabled PNP: 002e.9 disabled PNP: 002e.a disabled I2C: 70 enabled I2C: 50 enabled I2C: 51 enabled I2C: 52 enabled I2C: 53 enabled I2C: 54 enabled I2C: 55 enabled I2C: 56 enabled I2C: 57 enabled PCI: pci_scan_bus returning with max=04 PCI: pci_scan_bus returning with max=04 done Allocating resources... Reading resources... PCI: 01:01.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 2 io PCI: 01:01.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 2 prefmem PCI: 01:02.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 3 io PCI: 01:02.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 3 prefmem PCI: 01:02.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 3 mem PCI: 01:03.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 4 prefmem Done reading resources. Setting resources... PCI: 00:18.0 1b8 <- [0x00fd300000 - 0x00fd2fffff] prefmem PCI: 00:18.0 1c0 <- [0x0000001000 - 0x0000002fff] io PCI: 00:18.0 1b0 <- [0x00fc000000 - 0x00fd2fffff] mem PCI: 01:01.0 20 <- [0x00fd100000 - 0x00fd1fffff] bus 2 mem PCI: 02:03.0 10 <- [0x00fd100000 - 0x00fd10ffff] mem PCI: 02:03.0 30 <- [0x00fd110000 - 0x00fd11ffff] rom PCI: 02:04.0 10 <- [0x00fd120000 - 0x00fd12ffff] mem PCI: 02:04.0 30 <- [0x00fd130000 - 0x00fd13ffff] rom PCI: 01:01.1 10 <- [0x00fd200000 - 0x00fd200fff] mem PCI: 01:02.1 10 <- [0x00fd201000 - 0x00fd201fff] mem PCI: 01:03.0 1c <- [0x0000001000 - 0x0000001fff] bus 4 io PCI: 01:03.0 20 <- [0x00fc000000 - 0x00fd0fffff] bus 4 mem PCI: 04:00.0 10 <- [0x00fd000000 - 0x00fd000fff] mem PCI: 04:00.1 10 <- [0x00fd001000 - 0x00fd001fff] mem PCI: 04:06.0 10 <- [0x00fc000000 - 0x00fcffffff] mem PCI: 04:06.0 14 <- [0x0000001000 - 0x00000010ff] io PCI: 04:06.0 18 <- [0x00fd002000 - 0x00fd002fff] mem PCI: 04:06.0 30 <- [0x00fff80000 - 0x00fff9ffff] rom PNP: 002e.3 60 <- [0x00000003f8 - 0x00000003ff] io PNP: 002e.3 70 <- [0x0000000004 - 0x0000000004] irq PNP: 002e.6 60 <- [0x0000000060 - 0x0000000067] io PNP: 002e.6 62 <- [0x0000000064 - 0x000000006b] io PNP: 002e.6 70 <- [0x0000000001 - 0x0000000001] irq PCI: 01:04.1 20 <- [0x00000028a0 - 0x00000028af] io PCI: 01:04.2 10 <- [0x0000002880 - 0x000000289f] io PCI: 01:04.3 58 <- [0x0000002000 - 0x00000020ff] io PCI: 01:04.6 10 <- [0x0000002400 - 0x00000024ff] io PCI: 01:04.6 14 <- [0x0000002800 - 0x000000287f] io PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] mem Done setting resources. Done allocating resources. Enabling resourcess... PCI: 00:18.0 cmd <- 140 PCI: 01:01.0 bridge ctrl <- 0003 PCI: 01:01.0 cmd <- 146 PCI: 02:03.0 cmd <- 142 PCI: 02:04.0 cmd <- 142 PCI: 01:01.1 subsystem <- 161f/3016 PCI: 01:01.1 cmd <- 146 PCI: 01:02.0 bridge ctrl <- 0003 PCI: 01:02.0 cmd <- 140 PCI: 01:02.1 subsystem <- 161f/3016 PCI: 01:02.1 cmd <- 146 PCI: 01:03.0 bridge ctrl <- 0003 PCI: 01:03.0 cmd <- 147 PCI: 04:00.0 subsystem <- 161f/3016 PCI: 04:00.0 cmd <- 142 PCI: 04:00.1 subsystem <- 161f/3016 PCI: 04:00.1 cmd <- 142 PCI: 04:06.0 subsystem <- 161f/3016 PCI: 04:06.0 cmd <- 1c3 PCI: 01:04.0 subsystem <- 161f/3016 PCI: 01:04.0 cmd <- 14f PCI: 01:04.1 subsystem <- 161f/3016 PCI: 01:04.1 cmd <- 141 PCI: 01:04.2 subsystem <- 161f/3016 PCI: 01:04.2 cmd <- 141 PCI: 01:04.3 subsystem <- 161f/3016 PCI: 01:04.3 cmd <- 141 PCI: 01:04.6 subsystem <- 161f/3016 PCI: 01:04.6 cmd <- 141 PCI: 00:18.1 subsystem <- 161f/3016 PCI: 00:18.1 cmd <- 140 PCI: 00:18.2 subsystem <- 161f/3016 PCI: 00:18.2 cmd <- 140 PCI: 00:18.3 cmd <- 140 done. Initializing devices... Root Device init APIC_CLUSTER: 0 init Initializing CPU #0 CPU: vendor AMD device f5a Enabling cache Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB Setting fixed MTRRs(24-88) Type: WB DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 512MB, type WB DONE variable MTRRs Clear out the extra MTRR's MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled Clearing memory 0K - 524288K: ------- done Setting up local apic... apic_id: 0 done. CPU #0 Initialized APIC delivery error (4). CPU 1 would not start! CPU 1 did not initialize! All AP CPUs stopped PCI: 00:18.0 init PCI: 01:01.0 init PCI: 01:02.0 init PCI: 01:03.0 init PCI: 01:04.0 init RTC Init Invalid CMOS LB checksum enabling HPET @0xfed00000 PNP: 002e.3 init PNP: 002e.6 init PCI: 01:04.1 init IDE1 IDE0 PCI: 01:04.3 init set power on after power fail PCI: 00:18.3 init NB: Function 3 Misc Control.. done. Devices initialized Copying IRQ routing tables to 0xf0000...done. Verifing copy of IRQ routing tables at 0xf0000...done Checking IRQ routing table consistency... check_pirq_routing_table() - irq_routing_table located at: 0x000f0000 done. Wrote the mp table end at: 00000020 - 00000208 Wrote linuxbios table at: 00000500 - 00000d78 checksum 9652 Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3 23:stream_init() - rom_stream: 0xfffe0000 - 0xfffebfff Found ELF candiate at offset 0 New segment addr 0x100000 size 0x20bb0 offset 0xa0 filesize 0x6c08 (cleaned up) New segment addr 0x100000 size 0x20bb0 offset 0xa0 filesize 0x6c08 New segment addr 0x120bc0 size 0x48 offset 0x6cc0 filesize 0x48 (cleaned up) New segment addr 0x120bc0 size 0x48 offset 0x6cc0 filesize 0x48 Dropping non PT_LOAD segment Loading Segment: addr: 0x0000000000100000 memsz: 0x0000000000020bb0 filesz: 0x0000000000006c08 Clearing Segment: addr: 0x0000000000106c08 memsz: 0x0000000000019fa8 Loading Segment: addr: 0x0000000000120bc0 memsz: 0x0000000000000048 filesz: 0x0000000000000048 Jumping to boot code at 0x104790 FILO version 0.4.2 (root@localhost.localdomain) Thu Sep 22 15:46:08 CST 2005 Press for default boot, or for boot prompt... boot: hda1:/vmlinuz-2.6.13.2 root=/dev/hda1 console=tty0 console=ttyS0,115200 hda: LBA 20GB: ST320014A Mounted ext2fs Found Linux version 2.6.13.2 (root@localhost.localdomain) #1 Thu Sep 29 00:52:39 CST 2005 bzImage. Loading kernel... ok Jumping to entry point... Bootdata ok (command line is root=/dev/hda1 console=tty0 console=ttyS0,115200) Linux version 2.6.13.2 (root@localhost.localdomain) (gcc version 3.4.3 20050227 (Red Hat 3.4.3-22.1)) #1 Thu Sep 29 00:52:39 CST 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000de0 - 00000000000a0000 (usable) BIOS-e820: 0000000000100000 - 0000000020000000 (usable) ACPI: Unable to locate RSDP Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: LNXI <6>Product ID: HDAMA <6>APIC at: 0xFEE00000 Processor #0 15:5 APIC version 16 I/O APIC #2 Version 17 at 0xFEC00000. I/O APIC #3 Version 17 at 0xFD200000. I/O APIC #4 Version 17 at 0xFD201000. Setting APIC routing to flat Processors: 1 Allocating PCI resources starting at 20000000 (gap: 20000000:e0000000) Checking aperture... CPU 0: aperture @ f8000000 size 64 MB Built 1 zonelists Kernel command line: root=/dev/hda1 console=tty0 console=ttyS0,115200 Initializing CPU#0 PID hash table entries: 2048 (order: 11, 65536 bytes) time.c: Using 1.193182 MHz PIT timer. time.c: Detected 2405.536 MHz processor. time.c: Using PIT/TSC based timekeeping. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 510048k/524288k available (2761k kernel code, 13692k reserved, 1262k data, 184k init) Calibrating delay using timer specific routine.. 4820.55 BogoMIPS (lpj=9641114) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) mtrr: v2.0 (20020519) CPU: stepping 0a Using IO-APIC 2 Using IO-APIC 3 Using IO-APIC 4 Using local APIC timer interrupts. Detected 12.528 MHz APIC timer. testing NMI watchdog ... OK. NET: Registered protocol family 16 PCI: Using configuration type 1 ACPI: Subsystem revision 20050408 ACPI: Interpreter disabled. usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Discovered primary peer bus 01 [IRQ] PCI: Using IRQ router default [1022/746b] at 0000:01:04.3 PCI->APIC IRQ transform: 0000:02:03.0[A] -> IRQ 193 PCI->APIC IRQ transform: 0000:02:04.0[A] -> IRQ 193 PCI-DMA: Disabling IOMMU. PCI: Bridge: 0000:01:01.0 IO window: disabled. MEM window: fd100000-fd1fffff PREFETCH window: disabled. PCI: Bridge: 0000:01:02.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:01:03.0 IO window: 1000-1fff MEM window: fc000000-fd0fffff PREFETCH window: 20000000-200fffff IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ audit: initializing netlink socket (disabled) audit(1128416801.516:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API PCI: MSI quirk detected. pci_msi_quirk set. PCI: MSI quirk detected. pci_msi_quirk set. pci_hotplug: PCI Hot Plug PCI Core version: 0.5 Real Time Clock Driver v1.12 Linux agpgart interface v0.101 (c) Dave Jones [drm] Initialized drm 1.0.0 20040925 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled ÿttyS0 at I/O 0x3f8 (irq = 4) is a 16550A PCI: No IRQ known for interrupt pin B of device 0000:01:04.6. Probably buggy MP table. io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AMD8111: IDE controller at PCI slot 0000:01:04.1 AMD8111: chipset revision 3 AMD8111: not 100% native mode: will probe irqs later AMD8111: 0000:01:04.1 (rev 03) UDMA133 controller ide0: BM-DMA at 0x28a0-0x28a7, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x28a8-0x28af, BIOS settings: hdc:pio, hdd:pio hda: ST320014A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: max request size: 128KiB hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 ide-floppy driver 0.99.newide usbmon: debugfs is not available usbcore: registered new driver hiddev usbcore: registered new driver usbhid /root/linux-2.6.13.2/drivers/usb/input/hid-core.c: v2.01:USB HID core driver mice: PS/2 mouse device common for all mice md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 3.38 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 9, 3670016 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.3) powernow-k8: BIOS error - no PSB or ACPI _PSS objects md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. EXT2-fs warning (device hda1): ext2_fill_super: mounting ext3 filesystem as ext2 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 184k freed Warning: unable to open an initial console. Kernel panic - not syncing: No init found. Try passing init= option to kernel.