LinuxBIOS-1.1.8.0Normal Fri Apr 21 04:23:44 EDT 2006 starting...
Setting up default parameters for memory
Sizing memory
Probing for DIMM0
Probing for DIMM1
    Found DIMM1
    Page Size:       00001000
    Component Banks: 4
    Module Banks:    1
    DIMM size:       04000000
MC_BANK_CFG = 14200070
Copying LinuxBIOS to ram.
Jumping to LinuxBIOS.
LinuxBIOS-1.1.8.0Normal Fri Apr 21 04:23:44 EDT 2006 booting...
clocks_per_usec: 449
Enumerating buses...
Finding PCI configuration type.
PCI: Using configuration type 1
PCI_DOMAIN: 0000 enabled
PCI: pci_scan_bus for bus 0
PCI: 00:00.0 [1078/0001] enabled
PCI: 00:12.0 [1078/0100] enabled
PCI: 00:12.1 [1078/0101] enabled
PCI: 00:12.2 [1078/0102] enabled
PCI: 00:12.3 [1078/0103] enabled
PCI: 00:12.4 [1078/0104] enabled
PCI: 00:13.0 [0e11/a0f8] enabled
PCI: 00:15.0 [100b/0020] enabled
PNP: 002e.0 enabled
PNP: 002e.1 enabled
PNP: 002e.2 enabled
PNP: 002e.3 disabled
PNP: 002e.4 enabled
PNP: 002e.5 enabled
PNP: 002e.6 enabled
PNP: 002e.7 enabled
PNP: 002e.8 enabled
PCI: 00:12.1 disabled
PCI: 00:12.2 enabled
PCI: 00:12.3 disabled
PCI: 00:12.4 disabled
PCI: pci_scan_bus returning with max=00
done
Allocating resources...
Reading resources...
Done reading resources.
Setting resources...
BC_DRAM_TOP = 0x03bfffff
MC_GBASE_ADD = 0x00000078
I would set ram size to 60 Mbytes
PCI: 00:12.1 10 <- [0x00febf3000 - 0x00febf30ff] mem
PCI: 00:12.2 20 <- [0x0000001400 - 0x000000147f] io
PCI: 00:12.3 10 <- [0x00febf4000 - 0x00febf407f] mem
PCI: 00:12.4 10 <- [0x00febf0000 - 0x00febf0fff] mem
PCI: 00:13.0 10 <- [0x00febf1000 - 0x00febf1fff] mem
PCI: 00:15.0 10 <- [0x0000001000 - 0x00000010ff] io
PCI: 00:15.0 14 <- [0x00febf2000 - 0x00febf2fff] mem
PCI: 00:15.0 30 <- [0x00febe0000 - 0x00febeffff] romem
Done setting resources.
Done allocating resources.
Enabling resources...
PCI: 00:00.0 cmd <- 147
PCI: 00:12.0 cmd <- 14f
PCI: 00:12.2 missing enable_resources
PCI: 00:12.1 cmd <- 142
PCI: 00:12.2 cmd <- 141
PCI: 00:12.3 cmd <- 142
PCI: 00:12.4 cmd <- 142
PCI: 00:13.0 cmd <- 142
PCI: 00:15.0 cmd <- 143
done.
Initializing devices...
Root Device init
PCI: 00:00.0 init
northbridge: northbridge_init()
PCI: 00:12.0 init
PNP: 002e.0 init
PNP: 002e.1 init
PNP: 002e.2 init
PNP: 002e.4 init
PNP: 002e.5 init
PNP: 002e.6 init
PNP: 002e.7 init
PNP: 002e.8 init
PCI: 00:12.1 init
PCI: 00:12.2 init
PCI: 00:12.3 init
PCI: 00:12.4 init
PCI: 00:13.0 init
PCI: 00:15.0 init
Devices initialized
Copying IRQ routing tables to 0xf0000...done.
Verifing copy of IRQ routing tables at 0xf0000...failed
Moving GDT to 0x500...ok
Wrote linuxbios table at: 00000530 - 000006b0  checksum c9bc

Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3

    33:stream_init() - rom_stream: 0xfffc0000 - 0xfffcffff
Found ELF candiate at offset 0
New segment addr 0x100000 size 0x23600 offset 0xc0 filesize 0x9568
(cleaned up) New segment addr 0x100000 size 0x23600 offset 0xc0 filesize 0x9568
New segment addr 0x123600 size 0x48 offset 0x9640 filesize 0x48
(cleaned up) New segment addr 0x123600 size 0x48 offset 0x9640 filesize 0x48
Dropping non PT_LOAD segment
Dropping non PT_LOAD segment
Loading Segment: addr: 0x0000000000100000 memsz: 0x0000000000023600 filesz: 0x00
00000000009568
Clearing Segment: addr: 0x0000000000109568 memsz: 0x000000000001a098
Loading Segment: addr: 0x0000000000123600 memsz: 0x0000000000000048 filesz: 0x00
00000000000048
Jumping to boot code at 0x107684
FILO version 0.4.2 (root@fc4-dev) Fri Apr 21 04:11:43 EDT 2006
Press <Enter> for default boot, or <Esc> for boot prompt... timed out
boot: hda1:/vmlinuz root=/dev/hda1 console=tty0 console=ttyS0,115200
IDE time out
No drive detected on IDE channel 0
boot: hda1:/vmlinuz root=/dev/hda1 console=tty0 console=ttyS0,115200