I know it is friday and we are all tired....<br><br>I have a VGA device off amd8132 channel B<br>Trying VGA but LB hangs on the emulator.....<br>It looks like the VGA image is OK and loading... but,<br> Any help would be appreciated.... <br>-----------------------------------------------------------------------<br>LB output....<br><br>PCI: 42:01.0 10 <- [0x00f0000000 - 0x00f7ffffff] prefmem<br>PCI: 42:01.0 14 <- [0x0000004000 - 0x00000040ff] io<br>PCI: 42:01.0 18 <- [0x00fc000000 - 0x00fc00ffff] mem<br>PCI: 42:01.0 30 <- [0x00fff80000 - 0x00fff9ffff] romem<br>...<br>Setting up local apic... apic_id: 1 done.<br>CPU #1 Initialized<br>All AP CPUs stopped<br>PCI: 00:18.0 init<br>PCI: 40:00.0 init<br>PCI: 40:00.1 init<br>PCI: 40:01.0 init<br>PCI: 42:01.0 init<br>rom address for PCI: 42:01.0 = fff80000<br>copying VGA ROM Image from 0xfff80000 to 0xc0000, 0xf000 bytes<br>entering emulator<br><hangs
 here><br>-----------------------------------------------------------------------------<br>My Config.lb....<br><br>chip southbridge/amd/amd8132<br>    device pci 0.0 on end            # Channel A<br>    device pci 0.1 on end <br>    device pci 1.0 on                    # Channel B<br>        chip drivers/pci/onboard<br>            device pci 1.0 on end<br>            register "rom_address" = "0xfff80000"    #  start of video bios = rom_addres = 4G - 512K<br>        end<br>    end<br>    device pci 1.1 on
 end<br><br>-------------------------------------------------------------<br>my mptables.c part....<br><br>//----- "VGA        42:01.0 ----- ATI FIreGL 9000<br>smp_write_intsrc(mc,mp_INT,MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8132_2, (1<<2) |0, apicid_8132_2, 19);<br><br>-----------------------------------------------------------<br>Data from original BIOS<br><br>12:01.0 VGA compatible controller: ATI Technologies Inc Radeon R250 Lf [FireGL 9000] (rev 02) (prog-if 00 [VGA])<br>    Subsystem: ATI Technologies Inc Radeon R250 Lf [FireGL 9000]<br>    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-<br>    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-<br>    Latency: 255 (2000ns min), Cache Line Size 08<br>    Interrupt: pin A routed to IRQ
 5<br>    Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]<br>    Region 1: I/O ports at 5c00 [size=256]<br>    Region 2: Memory at dfdf0000 (32-bit, non-prefetchable) [size=64K]<br>    [virtual] Expansion ROM at dfd00000 [disabled] [size=128K]<br>    Capabilities: [50] Power Management version 2<br>        Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)<br>        Status: D0 PME-Enable- DSel=0 DScale=0 PME-<br>---------------------------------------------<br>VGA Rom part starts w/ 0x55aa<br>size =  61440<br>---------------------------------------------<br>#VGA Console<br>default CONFIG_CONSOLE_VGA=1<br>default CONFIG_PCI_ROM_RUN=1<br>----------------------------------------------<br>etherboot...<br># for btext console support<br>CFLAGS+=    -DCONSOLE_BTEXT<br># for direct PC kbd
 support<br>CFLAGS+=    -DCONSOLE_PC_KBD<br>------------------------------------------------<br><br><p>
                <hr size=1>Yahoo! Messenger with Voice. <a href="http://us.rd.yahoo.com/mail_us/taglines/postman1/*http://us.rd.yahoo.com/evt=39663/*http://voice.yahoo.com">Make PC-to-Phone Calls</a> to the US (and 30+ countries) for 2¢/min or less.