After upgrading to gcc-4.1.1 from gcc-3.4.4: not a single LB image will boot.<br><br>LB is the correct size.<br>Filo Builds.<br>LB detects all the hardware.<br>LB finds the kernel.<br>LB starts to load the kernel.... then SOFT RESET.<br>I have not changed any of my configurations & have done comparisons between gcc-3.4.1 & 4.1.1:<br><br>I think it may be a problem with Filo, but I am not sure.<br>Any Ideas?<br><br><br>LinuxBIOS-1.1.8_mb06048_Fallback Thu Sep 14 11:57:09 EDT 2006 starting...<br>resourcemap.c is setting up resources<br>(0,1) link=01<br>(1,0) link=02<br>02 nodes initialized.<br>SBLink=02<br>NC node|link=00<br> busn=40<br>NC node|link=02<br>SMBus controller enabled<br>Ram1.00<br>Ram1.01<br>Ram2.00<br>Ram2.01<br>Ram3<br>Initializing memory: done<br>Initializing memory: done<br>Ram4<br>v_esp=000cfd8c<br>testx = 5a5a5a5a<br>Copying data from cache to ram -- switching to use ram as stack... Done<br>testx
= 5a5a5a5a<br>Disabling cache as ram now<br>Clearing initial memory region: Done<br>Copying LinuxBIOS to ram.<br>src=fffe0000<br>dst=00004000<br>linxbios_ram.bin length = 000240fc<br>Jumping to LinuxBIOS.<br>LinuxBIOS-1.1.8_mb06048_Fallback Thu Sep 14 11:57:09 EDT 2006 booting...<br>Enumerating buses...<br>PCI_DOMAIN: 0000 enabled<br>APIC_CLUSTER: 0 enabled<br>PCI: Scanning Bus 0<br>PCI: 00:18.0 [1022/1100] enabled<br>PCI: 00:18.1 [1022/1101] enabled<br>PCI: 00:18.2 [1022/1102] enabled<br>PCI: 00:18.3 [1022/1103] enabled<br>PCI: 00:19.0 [1022/1100] enabled<br>PCI: 00:19.1 [1022/1101] enabled<br>PCI: 00:19.2 [1022/1102] enabled<br>PCI: 00:19.3 [1022/1103] enabled<br>PCI: 01:00.0 [1022/7458] enabled<br>PCI: 01:01.0 [1022/7458] enabled next_unitid: 0003<br>PCI: Scanning Bus 1<br>PCI: 01:01.0 [1022/7458] enabled<br>PCI: 01:01.1 [1022/7459] enabled<br>PCI: 01:02.0 [1022/7458] enabled<br>PCI: 01:02.1 [1022/7459] enabled<br>PCI: Scanning Bus 2<br>PCI: Found 2 Sub
Busses<br>PCI: 02: 133MHz PCI-X sstatus=60c3 rev=11<br>PCI: Scanning Bus 3<br>PCI: 03:01.0 [1002/4c66] enabled<br>PCI: Found 3 Sub Busses<br>PCI: 03: Conventional PCI sstatus=6003 rev=11<br>PCI: Found 3 Sub Busses<br>PCI: 04:00.0 [10de/005e] enabled<br>PCI: 04:00.0 [10de/005e] enabled next_unitid: 000f<br>PCI: 04:06.0<br>PCI: 04:09.0<br>PCI: 04:0a.0<br>PCI: 04:0b.0<br>PCI: 04:0c.0<br>PCI: 04:0d.0<br>PCI: 04:0e.0<br>HT: Left over static devices. Check your Config.lb<br>PCI: Scanning Bus 4<br>PCI: 04:00.0 [10de/005e] enabled<br>PCI: 04:01.0 [10de/0051] enabled<br>PCI: 04:01.1 [10de/0052] enabled<br>PCI: 04:02.0 [10de/005a] enabled<br>PCI: 04:02.1 [10de/005b] enabled<br>PCI: 04:04.0 [10de/0059] enabled<br>PCI: 04:04.1 [10de/0058] enabled<br>PCI: 04:06.0 [10de/0053] enabled<br>PCI: 04:07.0 [10de/0054] enabled<br>PCI: 04:08.0 [10de/0055] enabled<br>PCI: 04:09.0 [10de/005c] enabled<br>PCI: 04:0a.0 [10de/0057] enabled<br>PCI: 04:0b.0 [10de/005d] enabled<br>PCI: 04:0c.0
[10de/005d] enabled<br>PCI: 04:0d.0 [10de/005d] enabled<br>PCI: 04:0e.0 [10de/005d] enabled<br>PNP: 002e.0 disabled<br>PNP: 002e.1 disabled<br>PNP: 002e.2 enabled<br>PNP: 002e.3 enabled<br>PNP: 002e.5 enabled<br>PNP: 002e.6 disabled<br>PNP: 002e.7 disabled<br>PNP: 002e.8 disabled<br>PNP: 002e.9 disabled<br>PNP: 002e.a disabled<br>PNP: 002e.b enabled<br>smbus: PCI: 04:01.1[0]->I2C: 01:50 enabled<br>smbus: PCI: 04:01.1[0]->I2C: 01:51 enabled<br>PCI: Scanning Bus 5<br>PCI: Found 5 Sub Busses<br>PCI: Scanning Bus 6<br>PCI: 06:00.0 [11ab/4360] enabled<br>PCI: Found 6 Sub Busses<br>PCI: Scanning Bus 7<br>PCI: Found 7 Sub Busses<br>PCI: Scanning Bus 8<br>PCI: 08:00.0 [11ab/4360] enabled<br>PCI: Found 8 Sub Busses<br>PCI: Scanning Bus 9<br>PCI: Found 9 Sub Busses<br>PCI: Found 9 Sub Busses<br>PCI: Found 9 Sub Busses<br> PCI: 00:18.3 siblings=1<br>CPU: APIC: 00 enabled<br>CPU: APIC: 01 enabled<br> PCI: 00:19.3 siblings=1<br>CPU: APIC: 02 enabled<br>CPU: APIC: 03
enabled<br>done<br>Allocating resources...<br>Reading resources...<br>PCI: 01:01.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 2 io<br>PCI: 01:01.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 2 prefmem<br>PCI: 01:01.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 2 mem<br>PCI: 04:09.0 1c <- [0x000000f000 - 0x000000efff] bus 5 io<br>PCI: 04:09.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 5 prefmem<br>PCI: 04:09.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 5 mem<br>PCI: 04:0b.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 6 prefmem<br>PCI: 04:0c.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 7 io<br>PCI: 04:0c.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 7 prefmem<br>PCI: 04:0c.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 7 mem<br>PCI: 04:0d.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 8 prefmem<br>PCI: 04:0e.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 9 io<br>PCI: 04:0e.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 9
prefmem<br>PCI: 04:0e.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 9 mem<br>Done reading resources.<br>Allocating VGA resource PCI: 03:01.0<br>Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 01:02.0<br>Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0<br>Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000<br>Setting PCI_BRIDGE_CTL_VGA for bridge Root Device<br>Setting resources...<br>VGA: PCI: 00:18.0 (aka node 0) link 0 has VGA device<br>PCI: 00:18.0 1d8 <- [0x0000006000 - 0x0000006fff] io <node 0 link 0><br>PCI: 00:18.0 1b8 <- [0x00f0000000 - 0x00f7ffffff] prefmem <node 0 link 0><br>PCI: 00:18.0 1b0 <- [0x00fc300000 - 0x00fc4fffff] mem <node 0 link 0><br>PCI: 00:18.0 1d2 <- [0x0000001000 - 0x0000005fff] io <node 0 link 2><br>PCI: 00:18.0 1aa <- [0x00fc500000 - 0x00fc4fffff] prefmem <node 0 link 2><br>PCI: 00:18.0 1a2 <- [0x00fc000000 - 0x00fc2fffff] mem <node 0 link 2><br>PCI: 01:01.1 10 <- [0x00fc400000 -
0x00fc400fff] mem64<br>PCI: 01:02.0 1c <- [0x0000006000 - 0x0000006fff] bus 3 io<br>PCI: 01:02.0 24 <- [0x00f0000000 - 0x00f7ffffff] bus 3 prefmem<br>PCI: 01:02.0 20 <- [0x00fc300000 - 0x00fc3fffff] bus 3 mem<br>PCI: 03:01.0 10 <- [0x00f0000000 - 0x00f7ffffff] prefmem<br>PCI: 03:01.0 14 <- [0x0000006000 - 0x00000060ff] io<br>PCI: 03:01.0 18 <- [0x00fc300000 - 0x00fc30ffff] mem<br>PCI: 03:01.0 30 <- [0x00fff80000 - 0x00fff9ffff] romem<br>PCI: 01:02.1 10 <- [0x00fc401000 - 0x00fc401fff] mem64<br>PCI: 04:01.0 10 <- [0x0000004800 - 0x000000487f] io<br>PCI: 04:01.0 14 <- [0x00fc200000 - 0x00fc200fff] mem<br>PCI: 04:01.0 60 <- [0x0000003000 - 0x00000030ff] io<br>PCI: 04:01.0 64 <- [0x0000003400 - 0x00000034ff] io<br>PCI: 04:01.0 68 <- [0x0000003800 - 0x00000038ff] io<br>PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] io<br>PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] irq<br>PNP: 002e.3 60 <- [0x00000002f8 - 0x00000002ff]
io<br>PNP: 002e.3 70 <- [0x0000000003 - 0x0000000003] irq<br>PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io<br>PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io<br>PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq<br>PNP: 002e.5 72 <- [0x000000000c - 0x000000000c] irq<br>PNP: 002e.b 60 <- [0x0000000290 - 0x0000000297] io<br>PNP: 002e.b 70 <- [0x0000000005 - 0x0000000005] irq<br>PCI: 04:01.1 10 <- [0x0000004c80 - 0x0000004c9f] io<br>PCI: 04:01.1 20 <- [0x0000004c00 - 0x0000004c3f] io<br>PCI: 04:01.1 24 <- [0x0000004c40 - 0x0000004c7f] io<br>PCI: 04:02.0 10 <- [0x00fc201000 - 0x00fc201fff] mem<br>PCI: 04:02.1 10 <- [0x00fc207000 - 0x00fc2070ff] mem<br>PCI: 04:04.0 10 <- [0x0000003c00 - 0x0000003cff] io<br>PCI: 04:04.0 14 <- [0x0000004000 - 0x00000040ff] io<br>PCI: 04:04.0 18 <- [0x00fc202000 - 0x00fc202fff] mem<br>PCI: 04:04.1 10 <- [0x0000004400 - 0x00000044ff] io<br>PCI: 04:04.1 14 <- [0x0000004880 - 0x00000048ff]
io<br>PCI: 04:04.1 18 <- [0x00fc203000 - 0x00fc203fff] mem<br>PCI: 04:06.0 20 <- [0x0000004ca0 - 0x0000004caf] io<br>PCI: 04:07.0 10 <- [0x0000004cd0 - 0x0000004cd7] io<br>PCI: 04:07.0 14 <- [0x0000005010 - 0x0000005013] io<br>PCI: 04:07.0 18 <- [0x0000004ce0 - 0x0000004ce7] io<br>PCI: 04:07.0 1c <- [0x0000005020 - 0x0000005023] io<br>PCI: 04:07.0 20 <- [0x0000004cb0 - 0x0000004cbf] io<br>PCI: 04:07.0 24 <- [0x00fc204000 - 0x00fc204fff] mem<br>PCI: 04:08.0 10 <- [0x0000004cf0 - 0x0000004cf7] io<br>PCI: 04:08.0 14 <- [0x0000005030 - 0x0000005033] io<br>PCI: 04:08.0 18 <- [0x0000004d00 - 0x0000004d07] io<br>PCI: 04:08.0 1c <- [0x0000005040 - 0x0000005043] io<br>PCI: 04:08.0 20 <- [0x0000004cc0 - 0x0000004ccf] io<br>PCI: 04:08.0 24 <- [0x00fc205000 - 0x00fc205fff] mem<br>PCI: 04:0a.0 10 <- [0x00fc206000 - 0x00fc206fff] mem<br>PCI: 04:0a.0 14 <- [0x0000005000 - 0x0000005007] io<br>PCI: 04:0b.0 1c <- [0x0000001000 -
0x0000001fff] bus 6 io<br>PCI: 04:0b.0 20 <- [0x00fc000000 - 0x00fc0fffff] bus 6 mem<br>PCI: 06:00.0 10 <- [0x00fc020000 - 0x00fc023fff] mem64<br>PCI: 06:00.0 18 <- [0x0000001000 - 0x00000010ff] io<br>PCI: 06:00.0 30 <- [0x00fc000000 - 0x00fc01ffff] romem<br>PCI: 04:0d.0 1c <- [0x0000002000 - 0x0000002fff] bus 8 io<br>PCI: 04:0d.0 20 <- [0x00fc100000 - 0x00fc1fffff] bus 8 mem<br>PCI: 08:00.0 10 <- [0x00fc120000 - 0x00fc123fff] mem64<br>PCI: 08:00.0 18 <- [0x0000002000 - 0x00000020ff] io<br>PCI: 08:00.0 30 <- [0x00fc100000 - 0x00fc11ffff] romem<br>PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart><br>PCI: 00:19.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart><br>Done setting resources.<br>Done allocating resources.<br>Enabling resources...<br>PCI: 00:18.0 cmd <- 140<br>PCI: 01:01.0 bridge ctrl <- 0003<br>PCI: 01:01.0 cmd <- 140<br>PCI: 01:01.1 subsystem <- 1111/1111<br>PCI: 01:01.1 cmd <- 146<br>PCI:
01:02.0 bridge ctrl <- 000b<br>PCI: 01:02.0 cmd <- 147<br>PCI: 03:01.0 subsystem <- 1111/1111<br>PCI: 03:01.0 cmd <- 1c3<br>PCI: 01:02.1 subsystem <- 1111/1111<br>PCI: 01:02.1 cmd <- 146<br>PCI: 04:00.0 subsystem <- 1111/1111<br>PCI: 04:00.0 cmd <- 146<br>PCI: 04:01.0 subsystem <- 1111/1111<br>PCI: 04:01.0 cmd <- 14f<br>ck804 lpc decode:PNP: 002e.2, base=0x000003f8, end=0x000003ff<br>ck804 lpc decode:PNP: 002e.3, base=0x000002f8, end=0x000002ff<br>ck804 lpc decode:PNP: 002e.5, base=0x00000060, end=0x00000060<br>ck804 lpc decode:PNP: 002e.5, base=0x00000064, end=0x00000064<br>ck804 lpc decode:PNP: 002e.b, base=0x00000290, end=0x00000297<br>PCI: 04:01.1 subsystem <- 1111/1111<br>PCI: 04:01.1 cmd <- 141<br>PCI: 04:02.0 subsystem <- 1111/1111<br>PCI: 04:02.0 cmd <- 142<br>PCI: 04:02.1 subsystem <- 1111/1111<br>PCI: 04:02.1 cmd <- 142<br>PCI: 04:04.0 subsystem <- 1111/1111<br>PCI: 04:04.0 cmd <- 143<br>PCI: 04:04.1 subsystem
<- 1111/1111<br>PCI: 04:04.1 cmd <- 143<br>PCI: 04:06.0 subsystem <- 1111/1111<br>PCI: 04:06.0 cmd <- 141<br>PCI: 04:07.0 subsystem <- 1111/1111<br>PCI: 04:07.0 cmd <- 143<br>PCI: 04:08.0 subsystem <- 1111/1111<br>PCI: 04:08.0 cmd <- 143<br>PCI: 04:09.0 bridge ctrl <- 0003<br>PCI: 04:09.0 cmd <- 140<br>PCI: 04:0a.0 subsystem <- 1111/1111<br>PCI: 04:0a.0 cmd <- 143<br>PCI: 04:0b.0 bridge ctrl <- 0003<br>PCI: 04:0b.0 cmd <- 147<br>PCI: 06:00.0 cmd <- 143<br>PCI: 04:0c.0 bridge ctrl <- 0003<br>PCI: 04:0c.0 cmd <- 140<br>PCI: 04:0d.0 bridge ctrl <- 0003<br>PCI: 04:0d.0 cmd <- 147<br>PCI: 08:00.0 cmd <- 143<br>PCI: 04:0e.0 bridge ctrl <- 0003<br>PCI: 04:0e.0 cmd <- 140<br>PCI: 00:18.1 subsystem <- 1111/1111<br>PCI: 00:18.1 cmd <- 140<br>PCI: 00:18.2 subsystem <- 1111/1111<br>PCI: 00:18.2 cmd <- 140<br>PCI: 00:18.3 cmd <- 140<br>PCI: 00:19.0 cmd <- 140<br>PCI: 00:19.1 subsystem <-
1111/1111<br>PCI: 00:19.1 cmd <- 140<br>PCI: 00:19.2 subsystem <- 1111/1111<br>PCI: 00:19.2 cmd <- 140<br>PCI: 00:19.3 cmd <- 140<br>done.<br>Initializing devices...<br>Root Device init<br>PCI: 00:18.0 init<br>PCI: 01:01.0 init<br>PCI: 01:01.1 init<br>PCI: 01:02.0 init<br>PCI: 03:01.0 init<br>rom address for PCI: 03:01.0 = fff80000<br>copying VGA ROM Image from 0xfff80000 to 0xc0000, 0xf000 bytes<br>entering emulator<br>halt_sys: file /work/bios/linuxbios/src/devices/emulator/x86emu/ops.c, line 4387<br>PCI: 01:02.1 init<br>PCI: 04:01.0 init<br>set power on after power fail<br>RTC Init<br>Invalid CMOS LB checksum<br>PNP: 002e.2 init<br>PNP: 002e.3 init<br>PNP: 002e.5 init<br>PNP: 002e.b init<br>PCI: 04:02.1 init<br>PCI: 04:07.0 init<br>SATA S SATA P<br>PCI: 04:08.0 init<br>SATA S SATA P<br>PCI: 04:06.0 init<br>IDE1 IDE0<br>PCI: 04:09.0 init<br>dev_root mem base = 0x00f0000000<br>[0x50] <-- 0xf0000000<br>PCI: 04:0a.0 init<br>PCI:
04:0b.0 init<br>PCI: 04:0c.0 init<br>PCI: 04:0d.0 init<br>PCI: 04:0e.0 init<br>PCI: 00:18.1 init<br>PCI: 00:18.2 init<br>PCI: 00:18.3 init<br>NB: Function 3 Misc Control.. done.<br>PCI: 00:19.0 init<br>PCI: 00:19.1 init<br>PCI: 00:19.2 init<br>PCI: 00:19.3 init<br>NB: Function 3 Misc Control.. done.<br>APIC_CLUSTER: 0 init<br>Initializing CPU #0<br>CPU: vendor AMD device 20f12<br>Enabling cache<br><br>Setting fixed MTRRs(0-88) type: UC<br>Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM<br>Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM<br>DONE fixed MTRRs<br>Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB<br>Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB<br>Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC<br>DONE variable MTRRs<br>Clear out the extra MTRR's<br><br>MTRR check<br>Fixed MTRRs : Enabled<br>Variable MTRRs: Enabled<br><br>microcode: equivalent processor rev id = 0x0210, patch id =
0x00000000<br>microcode: patch id that want to apply= 0x0000004d<br>microcode: updated to patch id = 0x0000004d success<br>CPU model Dual Core AMD Opteron(tm) Processor 265 HE<br>Setting up local apic... apic_id: 0 done.<br>Clearing memory 2048K - 2097152K: ------------------------------- done<br>CPU #0 Initialized<br>Initializing CPU #1<br>CPU: vendor AMD device 20f12<br>Enabling cache<br><br>Setting fixed MTRRs(0-88) type: UC<br>Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM<br>Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM<br>DONE fixed MTRRs<br>Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB<br>Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB<br>Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC<br>DONE variable MTRRs<br>Clear out the extra MTRR's<br><br>MTRR check<br>Fixed MTRRs : Enabled<br>Variable MTRRs: Enabled<br><br>microcode: equivalent processor rev id = 0x0210, patch id =
0x00000000<br>microcode: patch id that want to apply= 0x0000004d<br>microcode: updated to patch id = 0x0000004d success<br>CPU model Dual Core AMD Opteron(tm) Processor 265 HE<br>Setting up local apic... apic_id: 1 done.<br>CPU #1 Initialized<br>Initializing CPU #2<br>CPU: vendor AMD device 20f12<br>Enabling cache<br><br>Setting fixed MTRRs(0-88) type: UC<br>Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM<br>Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM<br>DONE fixed MTRRs<br>Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB<br>Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB<br>Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC<br>DONE variable MTRRs<br>Clear out the extra MTRR's<br><br>MTRR check<br>Fixed MTRRs : Enabled<br>Variable MTRRs: Enabled<br><br>microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000<br>microcode: patch id that want to apply= 0x0000004d<br>microcode:
updated to patch id = 0x0000004d success<br>CPU model Dual Core AMD Opteron(tm) Processor 265 HE<br>Setting up local apic... apic_id: 2 done.<br>Clearing memory 2097152K - 5242880K: ----------------++++++++++++++++ done<br>CPU #2 Initialized<br>Initializing CPU #3<br>Waiting for 1 CPUS to stop<br>CPU: vendor AMD device 20f12<br>Enabling cache<br><br>Setting fixed MTRRs(0-88) type: UC<br>Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM<br>Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM<br>DONE fixed MTRRs<br>Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB<br>Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB<br>Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC<br>DONE variable MTRRs<br>Clear out the extra MTRR's<br><br>MTRR check<br>Fixed MTRRs : Enabled<br>Variable MTRRs: Enabled<br><br>microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000<br>microcode: patch id that want to
apply= 0x0000004d<br>microcode: updated to patch id = 0x0000004d success<br>CPU model Dual Core AMD Opteron(tm) Processor 265 HE<br>Setting up local apic... apic_id: 3 done.<br>CPU #3 Initialized<br>All AP CPUs stopped<br>PCI: 06:00.0 init<br>rom address for PCI: 06:00.0 = fc000000<br>Incorrect Expansion ROM Header Signature ffff<br>PCI: 08:00.0 init<br>rom address for PCI: 08:00.0 = fc100000<br>Incorrect Expansion ROM Header Signature ffff<br>Devices initialized<br>Writing IRQ routing tables to 0xf0000...done.<br>BUS: 0 is 0x9e<br>BUS: 1 is 0xa6<br>BUS: 2 is 0xae<br>BUS: 3 is 0xb6<br>BUS: 4 is 0xbe<br>BUS: 5 is 0xc6<br>BUS: 6 is 0xce<br>BUS: 7 is 0xd6<br>BUS: 8 is 0xde<br>BUS: 9 is 0xe6<br>BUS: 10 is 0xee<br>BUS: 1 is 0xf6<br>BUS: 2 is 0xfe<br>BUS: 3 is 0x106<br>IOAPIC: 4 version 0x11 @ 0xfc200000<br>IOAPIC: 5 version 0x11 @ 0xfc400000<br>IOAPIC: 6 version 0x11 @
0xfc401000<br><br>Mapping: 4:1.1 -> apic 4, irq 10<br>Mapping: 4:2.0 -> apic 4, irq 21<br>Mapping: 4:2.1 -> apic 4, irq 20<br>Mapping: 4:4.0 -> apic 4, irq 20<br>Mapping: 4:4.1 -> apic 4, irq 22<br>Mapping: 4:7.0 -> apic 4, irq 23<br>Mapping: 4:8.0 -> apic 4, irq 22<br>Mapping: 4:10.0 -> apic 4,
irq 21<br><br>Mapping: 5:0.0 -> apic 4, irq 16<br>Mapping: 5:0.1 -> apic 4, irq 17<br>Mapping: 5:0.2 -> apic 4, irq 18<br>Mapping: 5:0.3 -> apic 4, irq 19<br><br>Mapping: 6:0.0 -> apic 4, irq 17<br>Mapping: 6:0.1 -> apic 4, irq 18<br>Mapping: 6:0.2 -> apic 4, irq 19<br>Mapping: 6:0.3 ->
apic 4, irq 16<br><br>Mapping: 7:0.0 -> apic 4, irq 16<br>Mapping: 7:0.1 -> apic 4, irq 17<br>Mapping: 7:0.2 -> apic 4, irq 18<br>Mapping: 7:0.3 -> apic 4, irq 19<br><br>Mapping: 8:0.0 -> apic 4, irq 19<br>Mapping: 8:0.1 -> apic 4, irq 16<br>Mapping: 8:0.2 -> apic 4, irq 17<br>Mapping: 8:0.3
-> apic 4, irq 18<br><br>Mapping: 9:0.0 -> apic 4, irq 18<br>Mapping: 9:0.1 -> apic 4, irq 19<br>Mapping: 9:0.2 -> apic 4, irq 16<br>Mapping: 9:0.3 -> apic 4, irq 17<br><br>Mapping: 2:1.0 -> apic 5, irq 0<br>Mapping: 2:1.1 -> apic 5, irq 1<br>Mapping: 2:1.2 -> apic 5, irq 2<br>Mapping:
2:1.3 -> apic 5, irq 3<br><br>Mapping: 3:1.0 -> apic 6, irq 0<br>Mapping: 3:1.1 -> apic 6, irq 1<br>Mapping: 3:1.2 -> apic 6, irq 2<br>Mapping: 3:1.3 -> apic 6, irq 3<br><br>Mapping: 10:0.0 -> apic 4, irq 0<br>Mapping: 10:0.1 -> apic 4, irq 1<br>Mapping: 10:0.0 -> apic 4, irq 2<br>Mapping:
10:0.3 -> apic 4, irq 3<br>Mapping: 10:1.0 -> apic 4, irq 4<br>Mapping: 10:1.2 -> apic 4, irq 6<br>Mapping: 10:1.3 -> apic 4, irq 7<br>Mapping: 10:2.0 -> apic 4, irq 8<br>Mapping: 10:3.0 -> apic 4, irq 12<br>Mapping: 10:3.1 -> apic 4, irq 13<br>Mapping: 10:3.2 -> apic 4, irq 14<br>Mapping: 10:3.3
-> apic 4, irq 15<br>Mapping: 10:0.0 -> apic 255, irq 0<br>Mapping: 10:0.0 -> apic 255, irq 1<br>Wrote the mp table end at: 00000020 - 000002b4<br>Moving GDT to 0x500...ok<br>Wrote linuxbios table at: 00000530 - 000009f8 checksum 42f7<br><br>Welcome to elfboot, the open sourced starter.<br>January 2002, Eric Biederman.<br>Version 1.3<br><br>rom_stream: 0xfffc0000 - 0xfffdffff<br>Found ELF candiate at offset 0<br>New segment addr 0x100000 size 0x215c0 offset 0xe0 filesize 0x7608<br>(cleaned up) New segment addr 0x100000 size 0x215c0 offset 0xe0 filesize 0x7608<br>New segment addr 0x1215c0 size 0x48 offset 0x7700 filesize 0x48<br>(cleaned up) New segment addr 0x1215c0 size 0x48 offset 0x7700 filesize 0x48<br>Dropping non PT_LOAD segment<br>Dropping non PT_LOAD
segment<br>Dropping non PT_LOAD segment<br>Loading Segment: addr: 0x0000000000100000 memsz: 0x00000000000215c0 filesz: 0x0000000000007608<br>Clearing Segment: addr: 0x0000000000107608 memsz: 0x0000000000019fb8<br>Loading Segment: addr: 0x00000000001215c0 memsz: 0x0000000000000048 filesz: 0x0000000000000048<br>Jumping to boot code at 0x10557c<br>FILO version 0.5 (administrator@sky_bolt) Thu Sep 14 11:56:44 EDT 2006<br>Press <Enter> for default boot, or <Esc> for boot prompt...<br>boot: hde3:/boot/vmlinuz initrd=hde3:/boot/initramfs-genkernel-x86_64-2.6.15-gentoo-r7 real_root=/dev/sda3 pci=nommconf ro console=tty0 cons0<br>find_ide_controller: found PCI IDE controller 10de:0054 prog_if=0x85<br>find_ide_controller: primary channel: native PCI mode<br>find_ide_controller: cmd_base=0x4cd0 ctrl_base=0x5010<br>ide_software_reset: Waiting for ide2 to become ready for reset... ok<br>init_drive: Testing for hde<br>init_drive: Probing for hde<br>init_drive: LBA mode,
sectors=78140160<br>init_drive: LBA48 mode, sectors=78140160<br>init_drive: Init device params... ok<br>hde: LBA48 40GB: FUJITSU MHT2040BH<br>init_drive: Testing for hdf<br>init_drive: Probing for hdf<br>print_status: IDE: status=0x0, err=0x0<br>init_drive: Testing for hdf<br>init_drive: Probing for hdf<br>print_status: IDE: status=0x0, err=0x0<br>Mounted ext2fs<br>Found Linux version 2.6.15-gentoo-r7 (root@localhost) #6 SMP PREEMPT Wed Jun 21 16:40:43 EDT 2006 bzImage.<br>Loading kernel... ok<br>Jumping to entry point...<br><br><br><br>INIT detected from ---- {APICID = 00 NODEID = 00 COREID = 00} ---<br><br>Issuing SOFT_RESET...<br><br><br>LinuxBIOS-1.1.8_mb06048_Fallback Thu Sep 14 11:57:09 EDT 2006 starting...<br><br><br>TIA<br>steve<br><br><br><p>
<hr size=1>Stay in the know. Pulse on the new Yahoo.com. <a href="http://us.rd.yahoo.com/evt=42974/*http://www.yahoo.com/preview"> Check it out.</a>