Thanks for the help. But I have another doubt, I'm not getting video working even after the linux kernel boots. What do I do to change the console to video? I've configured Filo to use video console, but the stream goes only to serial interface.
<br><br>Regards,<br><br>Otávio Alcântara<br><br><div><span class="gmail_quote">On 6/20/07, <b class="gmail_sendername">Marc Jones</b> <<a href="mailto:marc.jones@amd.com">marc.jones@amd.com</a>> wrote:</span><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<br><br>Otávio Alcântara wrote:<br>> Hello to all,<br>><br>>           I'm porting a linuxbios v2 version for a board ref des<br>> LXUVCRDK (<a href="http://www.amd.com/geodelxuvcrdk">http://www.amd.com/geodelxuvcrdk
</a>) based on norwich board. I've<br>> already got to boot linux from HD, but it seems to halt in some point<br>> (see log below captured from serial). Although,  I'm using VSA<br>> (lx_vsa.36k.bin) and I got no output from video VGA.
<br>>           I'd like some help for setting up the PIRQ table and for VGA<br>> setup.<br>><br>> PS: The schematics for this board are publicly available from AMD<br>> Embedded Developer Web Site.<br>
><br>> Thanks,<br>><br>> --<br>> Otávio Alcântara<br>> "I'll never cross to the Dark Side."<br>><br>><br>><br><br>I took a quick look at the schematics and I think that this is what the
<br>PIRQ table should look like.<br><br>/* If you change the number of entries, change the IRQ_SLOT_COUNT above! */<br>/* bus, dev|fn,           {link, bitmap},      {link, bitmap},<br>{link, bitmap},     {link, bitmap},     slot, rfu */
<br>{0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00,<br>0x00}, {0x00, 0x00}}, 0x0, 0x0},        /* cpu */<br>{0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB},<br>{L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0},     /* chipset */
<br>{0x00, (0x0D << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00,<br>0x00}, {0x00, 0x00}}, 0x0, 0x0},        /* ethernet */<br><br>Make sure to change IRQ_SLOT_COUNT in the mainboard <a href="http://Options.lb">
Options.lb</a><br><br>As Jordan pointed out, you should use the Linux framebuffer and X<br>drivers instead of VGA. That means that you should also set<br>CONFIG_CONSOLE_VGA=0 and CONFIG_PCI_ROM_RUN=0 in <a href="http://Options.lb">
Options.lb</a><br><br><br>It also looks like there is something funny going on with the <a href="http://Config.lb">Config.lb</a>.<br>Try using the norwich one without modifications.<br><br> > cs5536: southbridge_init: enable_ide_nand_flash is 36
<br>If you want to boot from IDE enable_ide_nand_flash should be 0<br><br> > Disabling VPCI device: 0x0000106C<br> > Disabling VPCI device: 0x00001075<br> > Disabling VPCI device: 0x0000107E<br> > Disabling VPCI device: 0x00001087
<br> > Disabling VPCI device: 0x00001090<br> > Disabling VPCI device: 0x00001099<br> > Disabling VPCI device: 0x000010A2<br> > Disabling VPCI device: 0x000010AB<br>This is a very strange list.<br><br><br>I don't have one of these boards so when you get it working please
<br>submit a patch!<br>Let me know if there is anything else I can do to help<br><br>Marc<br><br><br><br>><br>> LinuxBIOS-2.0.0.0Fallback Qua Jun 20 07:45:43 BRT 2007 starting...<br>> _MSR GLCP_SYS_RSTPLL (4c000014) value is: 00000498:00001820
<br>> Configuring PLL<br>><br>><br>> LinuxBIOS-2.0.0.0Fallback Qua Jun 20 07:45:43 BRT 2007 starting...<br>> _MSR GLCP_SYS_RSTPLL (4c000014) value is: 00000498:07de0020<br>> Done cpuRegInit<br>> SMBUS READ ERROR:03 device:a2
<br>> Ram1.00<br>> Ram2.00<br>> SMBUS READ ERROR:03 device:a2<br>> SMBUS READ ERROR:03 device:a2<br>> SMBUS READ ERROR:03 device:a2<br>> SMBUS READ ERROR:03 device:a2<br>> SMBUS READ ERROR:03 device:a2
<br>> SMBUS READ ERROR:03 device:a2<br>> SMBUS READ ERROR:03 device:a2<br>> SMBUS READ ERROR:03 device:a2<br>> SMBUS READ ERROR:03 device:a2<br>> SMBUS READ ERROR:03 device:a2<br>> SMBUS READ ERROR:03 device:a2
<br>> Ram3<br>> DRAM controller init done.<br>> RAM DLL lock<br>> Ram4<br>> Copying LinuxBIOS to ram.<br>> Jumping to LinuxBIOS.<br>> LinuxBIOS-2.0.0.0Fallback Qua Jun 20 08:56:35 BRT 2007 booting...<br>
> clocks_per_usec: 432<br>> Enumerating buses...<br>>  >> Entering northbridge.c: pci_domain_enable<br>> Enter northbridge_init_early<br>> writeglmsr: MSR 0x10000020, val 0x20000000:0x000fff80<br>> writeglmsr: MSR 0x10000021, val 0x20000000:0x080fffe0
<br>> writeglmsr: MSR 0x1000002c, val 0x20000000:0x00000003<br>> sizeram: _MSR MC_CF07_DATA: 10076112:00004840<br>> sizeram: sizem 0x100MB<br>> SysmemInit: enable for 256MBytes<br>> usable RAM: 268304383 bytes
<br>> SysmemInit: MSR 0x10000028, val 0x2000000f:0xfdf00100<br>> sizeram: _MSR MC_CF07_DATA: 10076112:00004840<br>> sizeram: sizem 0x100MB<br>> SMMGL0Init: 268304384 bytes<br>> SMMGL0Init: offset is 0x80400000
<br>> SMMGL0Init: MSR 0x10000026, val 0x28fbe080:0x400fffe0<br>> writeglmsr: MSR 0x10000080, val 0x00000000:0x00000003<br>> writeglmsr: MSR 0x40000020, val 0x20000000:0x000fff80<br>> writeglmsr: MSR 0x40000021, val 0x20000000:0x080fffe0
<br>> writeglmsr: MSR 0x4000002e, val 0x20000000:0x00000003<br>> sizeram: _MSR MC_CF07_DATA: 10076112:00004840<br>> sizeram: sizem 0x100MB<br>> SysmemInit: enable for 256MBytes<br>> usable RAM: 268304383 bytes
<br>> SysmemInit: MSR 0x4000002a, val 0x2000000f:0xfdf00100<br>> SMMGL1Init:<br>> SMMGL1Init: MSR 0x40000023, val 0x20000080:0x400fffe0<br>> writeglmsr: MSR 0x40000080, val 0x00000000:0x00000001<br>> writeglmsr: MSR 0x400000e3, val 0x60000000:0x033000f0
<br>> CPU_RCONF_DEFAULT (1808): 0x25FFFC02:0x10FFDF00<br>> CPU_RCONF_BYPASS (180A): 0x00000000 : 0x00000000<br>> L2 cache enabled<br>> Enabling cache<br>> GLPCI R1: system msr.lo 0x00100130 msr.hi 0x0ffdf000
<br>> GLPCI R2: system msr.lo 0x80400120 msr.hi 0x8041f000<br>> Exit northbridge_init_early<br>> Done cpubug fixes<br>> Not Doing ChipsetFlashSetup()<br>> <<<WARNING>>> Graphics init...<br>
>  <<WARNING!!!>>> VRC_VG value: 0xffff<br>> Before VSA:<br>> do_vsmbios<br>> buf ilen 35441 olen60466<br>> buf 00060000 *buf 186 buf[256k] 0<br>> buf[0x20] signature is b0:10:e6:80<br>> Call real_mode_switch_call_vsm
<br>> biosint: INT# 0x15<br>> biosint: eax 0xbea7 ebx 0x4e53 ecx 0x10000026 edx 0x10000028<br>> biosint: ebp 0x15ed4 esp 0xff0 edi 0x8a71 esi 0x38<br>> biosint:  ip 0x5b3   cs 0x6000  flags 0x46<br>> biosint: gs 0x0 fs 0x0 ds 0x6000 es 0x0
<br>> handleint21, eax 0xbea7<br>> biosint: INT# 0x15<br>> biosint: eax 0xbea4 ebx 0x4e53 ecx 0x10000026 edx 0x10000028<br>> biosint: ebp 0x15ed4 esp 0xfee edi 0x8a71 esi 0x38<br>> biosint:  ip 0x5c1   cs 0x6000  flags 0x46
<br>> biosint: gs 0x0 fs 0x0 ds 0x6000 es 0x0<br>> handleint21, eax 0xbea4<br>> do_vsmbios: VSA2 VR signature verified<br>> After VSA:<br>> <<<WARNING>>> Graphics init...<br>>  <<WARNING!!!>>> VRC_VG value: 0x2808
<br>> Finding PCI configuration type.<br>> PCI: Using configuration type 1<br>> PCI_DOMAIN: 0000 enabled<br>> APIC_CLUSTER: 0 enabled<br>> PCI: pci_scan_bus for bus 00<br>> PCI: 00:01.0 [1022/2080] enabled
<br>> PCI: 00:01.1 [1022/2081] enabled<br>> PCI: 00:01.2 [1022/2082] enabled<br>> PCI: 00:0d.0 [10ec/8139] enabled<br>> PCI: 00:0f.0 [1022/2090] enabled<br>> PCI: 00:0f.2 [1022/209a] enabled<br>> PCI: 00:
0f.3 [1022/2093] enabled<br>> PCI: 00:0f.4 [1022/2094] enabled<br>> PCI: 00:0f.5 [1022/2095] enabled<br>> PCI: 00: 0f.6 [1022/2096] enabled<br>> PCI: 00:0f.7 [1022/2097] enabled<br>> PCI: pci_scan_bus returning with max=000
<br>> done<br>> Allocating resources...<br>> Reading resources...<br>> Done reading resources.<br>> Setting resources...<br>> PCI: 00: 01.1 10 <- [0x00fd000000 - 0x00fdffffff] mem<br>> PCI: 00:01.1
 14 <- [0x00fe000000 - 0x00fe003fff] mem<br>> PCI: 00:01.1 18 <- [0x00fe004000 - 0x00fe007fff] mem<br>> PCI: 00:01.1 1c <- [0x00fe008000 - 0x00fe00bfff] mem<br>> PCI: 00:01.1 20 <- [0x00fe00c000 - 0x00fe00ffff] mem
<br>> PCI: 00:01.2 10 <- [0x00fe010000 - 0x00fe013fff] mem<br>> PCI: 00:0d.0 10 <- [0x0000001000 - 0x00000010ff] io<br>> PCI: 00:0d.0 14 <- [0x00fe019000 - 0x00fe0190ff] mem<br>> PCI: 00:0f.0 10 <- [0x0000001cb0 - 0x0000001cb7] io
<br>> PCI: 00:0f.0 14 <- [0x0000001400 - 0x00000014ff] io<br>> PCI: 00:0f.0 18 <- [0x0000001c00 - 0x0000001c3f] io<br>> PCI: 00:0f.0 1c <- [0x0000001c80 - 0x0000001c9f] io<br>> PCI: 00:0f.0 20 <- [0x0000001800 - 0x000000187f] io
<br>> PCI: 00:0f.0 24 <- [0x0000001c40 - 0x0000001c7f] io<br>> PCI: 00:0f.2 20 <- [0x0000001ca0 - 0x0000001caf] io<br>> PCI: 00:0f.3 10 <- [0x0000001880 - 0x00000018ff] io<br>> PCI: 00:0f.4 10 <- [0x00fe016000 - 0x00fe016fff] mem
<br>> PCI: 00:0f.5 10 <- [0x00fe017000 - 0x00fe017fff] mem<br>> PCI: 00:0f.6 10 <- [0x00fe014000 - 0x00fe015fff] mem<br>> PCI: 00:0f.7 10 <- [0x00fe018000 - 0x00fe018fff] mem<br>> Done setting resources.
<br>> Done allocating resources.<br>> Enabling resources...<br>> PCI: 00:01.0 cmd <- 145<br>> PCI: 00:01.1 subsystem <- 00/00<br>> PCI: 00:01.1 cmd <- 142<br>> PCI: 00:01.2 cmd <- 142<br>> PCI: 00: 
0d.0 cmd <- 143<br>> cs5536: cs5536_pci_dev_enable_resources()<br>> PCI: 00:0f.0 cmd <- 149<br>> PCI: 00:0f.2 cmd <- 141<br>> PCI: 00:0f.3 cmd <- 141<br>> PCI: 00:0f.4 cmd <- 142<br>> PCI: 00:
0f.5 cmd <- 142<br>> PCI: 00: 0f.6 cmd <- 142<br>> PCI: 00:0f.7 cmd <- 142<br>> done.<br>> Initializing devices...<br>> Root Device init<br>> Norwich ENTER init<br>> Norwich EXIT init<br>> PCI: 00:
01.0 init<br>> PCI: 00:01.1 init<br>> APIC_CLUSTER: 0 init<br>> Initializing CPU #0<br>> CPU: vendor AMD device 5a2<br>> CPU: family 05, model 0a, stepping 02<br>> model_lx_init<br>> Enabling cache<br>
> A20 (0x92): 2<br>> A20 (0x92): 2<br>> CPU model_lx_init DONE<br>> CPU #0 Initialized<br>> PCI: 00:01.2 init<br>> PCI: 00: 0d.0 init<br>> PCI: 00:0f.0 init<br>> cs5536: southbridge_init<br>> RTC Init
<br>> rct_init finished<br>> cs5536: southbridge_init: enable_ide_nand_flash is 36<br>> Disabling VPCI device: 0x0000106C<br>> Disabling VPCI device: 0x00001075<br>> Disabling VPCI device: 0x0000107E<br>> Disabling VPCI device: 0x00001087
<br>> Disabling VPCI device: 0x00001090<br>> Disabling VPCI device: 0x00001099<br>> Disabling VPCI device: 0x000010A2<br>> Disabling VPCI device: 0x000010AB<br>> PCI: 00:0f.2 init<br>> PCI: 00:0f.3 init<br>
> PCI: 00:0f.4 init<br>> PCI: 00:0f.5 init<br>> PCI: 00:0f.6 init<br>> PCI: 00:0f.7 init<br>> Devices initialized<br>> Copying IRQ routing tables to 0xf0000...done.<br>> Verifing copy of IRQ routing tables at 0xf0000...done
<br>> Checking IRQ routing table consistency...<br>> check_pirq_routing_table() - irq_routing_table located at: 0x000f0000<br>> /home/otavio/LinuxBIOSv2/src/arch/i386/boot/pirq_routing.c:<br>> 36:check_pirq_routing_table() - checksum is: 0x00 but should be: 0xfd
<br>> done.<br>> write_pirq_routing_table(8000785C, BAAA)<br>> PIR Entry 0 Dev/Fn: 8 Slot: 0<br>> INT: A bitmap: 400 PIRQ: 10<br>> INT: B bitmap: 0 PIRQ: 0<br>> INT: C bitmap: 0 PIRQ: 0<br>> INT: D bitmap: 0 PIRQ: 0
<br>> Assigning IRQ 10 to 0: 1.1<br>>   Readback = 10<br>> Assigning IRQ 10 to 0:1.2<br>>   Readback = 10<br>> PIR Entry 1 Dev/Fn: 78 Slot: 0<br>> INT: A bitmap: 400 PIRQ: 10<br>> INT: B bitmap: 400 PIRQ: 10
<br>> INT: C bitmap: 400 PIRQ: 10<br>> INT: D bitmap: 800 PIRQ: 11<br>> Assigning IRQ 10 to 0:f.3<br>>   Readback = 10<br>> Assigning IRQ 11 to 0:f.4<br>>   Readback = 11<br>> Assigning IRQ 11 to 0:f.5
<br>>   Readback = 11<br>> PIR Entry 2 Dev/Fn: 68 Slot: 1<br>> INT: A bitmap: 400 PIRQ: 10<br>> INT: B bitmap: 400 PIRQ: 10<br>> INT: C bitmap: 800 PIRQ: 11<br>> INT: D bitmap: 400 PIRQ: 10<br>> Assigning IRQ 10 to 0:
d.0<br>>   Readback = 10<br>> PIR Entry 3 Dev/Fn: 70 Slot: 2<br>> INT: A bitmap: 400 PIRQ: 10<br>> INT: B bitmap: 800 PIRQ: 11<br>> INT: C bitmap: 400 PIRQ: 10<br>> INT: D bitmap: 400 PIRQ: 10<br>> PIR Entry 4 Dev/Fn: 58 Slot: 3
<br>> INT: A bitmap: 800 PIRQ: 11<br>> INT: B bitmap: 400 PIRQ: 10<br>> INT: C bitmap: 400 PIRQ: 10<br>> INT: D bitmap: 400 PIRQ: 10<br>> PIR Entry 5 Dev/Fn: 60 Slot: 4<br>> INT: A bitmap: 400 PIRQ: 10<br>
> INT: B bitmap: 400 PIRQ: 10<br>> INT: C bitmap: 400 PIRQ: 10<br>> INT: D bitmap: 800 PIRQ: 11<br>> Moving GDT to 0x500...ok<br>> Adjust low_table_end from 0x00000530 to 0x00001000<br>> Adjust rom_table_end from 0x000f0400 to 0x00100000
<br>> Wrote linuxbios table at: 00000530 - 000006c4  checksum fba9<br>><br>> Welcome to elfboot, the open sourced starter.<br>> January 2002, Eric Biederman.<br>> Version 1.3<br>><br>> rom_stream: 0xfff89000 - 0xfffeffff
<br>> Found ELF candidate at offset 0<br>> header_offset is 0<br>> Try to load at offset 0x0<br>> New segment addr 0x100000 size 0x306e0 offset 0xc0 filesize 0xb248<br>> (cleaned up) New segment addr 0x100000 size 0x306e0 offset 0xc0 filesize
<br>> 0xb248<br>> New segment addr 0x1306e0 size 0x48 offset 0xb320 filesize 0x48<br>> (cleaned up) New segment addr 0x1306e0 size 0x48 offset 0xb320 filesize 0x48<br>> Dropping non PT_LOAD segment<br>> Dropping non PT_LOAD segment
<br>> Loading Segment: addr: 0x0000000000100000 memsz: 0x00000000000306e0<br>> filesz: 0x000000000000b248<br>> Clearing Segment: addr: 0x000000000010b248 memsz: 0x0000000000025498<br>> Loading Segment: addr: 0x00000000001306e0 memsz: 0x0000000000000048
<br>> filesz: 0x0000000000000048<br>> Jumping to boot code at 0x108bdc<br>> FILO version 0.5 (otavio@labdes15) Wed Jun 20 08:56:24 BRT 2007<br>> collect_linuxbios_info: Searching for LinuxBIOS tables...<br>> find_lb_table: Found canidate at: 00000530
<br>> find_lb_table: header checksum o.k.<br>> find_lb_table: table checksum o.k.<br>> find_lb_table: record count o.k.<br>> collect_linuxbios_info: Found LinuxBIOS table at: 00000530<br>> convert_memmap: 0x00000000000000 0x00000000001000 16
<br>> convert_memmap: 0x00000000001000 0x0000000009f000 1<br>> convert_memmap: 0x000000000f0000 0x00000000010000 16<br>> convert_memmap: 0x00000000100000 0x0000000f6e0000 1<br>> Press <Enter> for default boot, or <Esc> for boot prompt... 2   1
<br>>  timed out<br>> boot: hda1:/boot/vmlinuz root=/dev/hda1 initrd=/boot/initrd<br>> console=tty0  console=ttyS0,115200<br>> hda: LBA 40GB: ST340014A<br>> Mounted ext2fs<br>> Found Linux version 2.6.8-2-386
 (<a href="mailto:horms@tabatha.lab.ultramonkey.org">horms@tabatha.lab.ultramonkey.org</a><br>> <mailto:<a href="mailto:horms@tabatha.lab.ultramonkey.org">horms@tabatha.lab.ultramonkey.org</a>>) #1 Thu May 19 17:40:50 JST
<br>> 2005 (protocol 0x203) (loadflags 0x1) bzImage.<br>> init_linux_params: Setting up paramters at 0x90000<br>> set_memory_size: 0000000000001000 - 00000000000a0000<br>> set_memory_size: 0000000000100000 - 000000000f7e0000
<br>> set_memory_size: ramtop=0xf7e0000<br>> set_memory_size: ext_mem_k=64512, alt_mem_k=252800<br>> parse_command_line: original command line: "root=/dev/hda1<br>> initrd=/boot/initrd console=tty0  console=ttyS0,115200"
<br>> parse_command_line: kernel command line at 0x91000<br>> parse_command_line: initrd=/boot/initrd<br>> parse_command_line: kernel command line (48 bytes): "root=/dev/hda1<br>> console=tty0 console=ttyS0,115200"
<br>> load_linux_kernel: offset=0x1600 addr=0x100000 size=0x10a8cb<br>> Loading kernel... ok<br>> load_initrd: start=0xf391000 end=0xf7af000<br>> Loading initrd... ok<br>> start_linux: eip=0x100000<br>> Jumping to entry point...
<br>> Linux version 2.6.8-2-386 (<a href="mailto:horms@tabatha.lab.ultramonkey.org">horms@tabatha.lab.ultramonkey.org</a><br>> <mailto:<a href="mailto:horms@tabatha.lab.ultramonkey.org">horms@tabatha.lab.ultramonkey.org
</a>>) (gcc version 3.3.5 (Debian<br>> 1:3.3.5-12)) #1 Thu May 19 17:40:50 JST 2005<br>><br>> BIOS-provided physical RAM map:<br>><br>>  BIOS-e820: 0000000000001000 - 00000000000a0000 (usable)<br>><br>
>  BIOS-e820: 0000000000100000 - 000000000f7e0000 (usable)<br>><br>> 247MB LOWMEM available.<br>><br>> DMI not present.<br>><br>> ACPI: Unable to locate RSDP<br>><br>> Built 1 zonelists<br>><br>
> Kernel command line: root=/dev/hda1 console=tty0 console=ttyS0,115200<br>><br>> No local APIC present or hardware disabled<br>><br>> Initializing CPU#0<br>><br>> PID hash table entries: 1024 (order 10: 8192 bytes)
<br>><br>> Detected 431.857 MHz processor.<br>><br>> Using tsc for high-res timesource<br>><br>> Console: colour dummy device 80x25<br>><br>> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
<br>><br>> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)<br>><br>> Memory: 244168k/253824k available (1336k kernel code, 8916k reserved,<br>> 732k data, 204k init, 0k highmem)<br>><br>> Checking if this processor honours the WP bit even in supervisor mode...
<br>> Ok.<br>><br>> Calibrating delay loop... 845.82 BogoMIPS<br>><br>> Security Scaffold v1.0.0 initialized<br>><br>> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)<br>><br>> CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
<br>><br>> CPU: L2 Cache: 128K (32 bytes/line)<br>><br>> CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02<br>><br>> Checking 'hlt' instruction... OK.<br>><br>> Checking for popad bug... OK.
<br>><br>> checking if image is initramfs...it isn't (ungzip failed); looks like an<br>> initrd<br>><br>> Freeing initrd memory: 4216k freed<br>><br>> NET: Registered protocol family 16<br>><br>
> EISA bus registered<br>><br>> PCI: Using configuration type 1<br>><br>> mtrr: v2.0 (20020519)<br>><br>> ACPI: Subsystem revision 20040326<br>><br>> ACPI: Interpreter disabled.<br>><br>> Linux Plug and Play Support 
v0.97 (c) Adam Belay<br>><br>> PnPBIOS: Scanning system for PnP BIOS support...<br>><br>> PnPBIOS: PnP BIOS support was not detected.<br>><br>> PCI: Probing PCI hardware<br>><br>> PCI: Probing PCI hardware (bus 00)
<br>><br>> PCI: Using IRQ router default [1022/2090] at 0000:00:0f.0<br>><br>> VFS: Disk quotas dquot_6.5.1<br>><br>> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)<br>><br>> devfs: 2004-01-31 Richard Gooch ( 
<a href="mailto:rgooch@atnf.csiro.au">rgooch@atnf.csiro.au</a><br>> <mailto:<a href="mailto:rgooch@atnf.csiro.au">rgooch@atnf.csiro.au</a>>)<br>><br>> devfs: boot_options: 0x0<br>><br>> Initializing Cryptographic API
<br>><br>> isapnp: Scanning for PnP cards...<br>><br>> isapnp: No Plug & Play device found<br>><br>> Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled<br>><br>> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<br>><br>> RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize<br>><br>> i8042.c : Can't read CTR while initializing i8042.<br>><br>> EISA: Probing bus 0 at eisa0<br>><br>> Cannot allocate resource for EISA slot 1
<br>><br>> EISA: Detected 0 cards.<br>><br>> NET: Registered protocol family 2<br>><br>> IP: routing cache hash table of 2048 buckets, 16Kbytes<br>><br>> TCP: Hash tables configured (established 16384 bind 32768)
<br>><br>> NET: Registered protocol family 8<br>><br>> NET: Registered protocol family 20<br>><br>> RAMDISK: cramfs filesystem found at block 0<br>><br>> RAMDISK: Loading 4216 blocks [1 disk] into ram disk... | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ done.
<br>><br>><br>> VFS: Mounted root (cramfs filesystem) readonly.<br>><br>> Freeing unused kernel memory: 204k freed<br>><br>> vesafb: probe of vesafb0 failed with error -6<br>><br>> NET: Registered protocol family 1
<br>><br>> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2<br>><br>> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx<br>><br>> hda: ST340014A, ATA DISK drive<br>><br>
> Using anticipatory io scheduler<br>><br>> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14<br>><br>> hda: max request size: 128KiB<br>><br>> hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63<br>>
<br>>  /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 ><br>><br>><br><br>--<br>Marc Jones<br>Senior Software Engineer<br>(970) 226-9684 Office<br>mailto:<a href="mailto:Marc.Jones@amd.com">Marc.Jones@amd.com</a>
<br><a href="http://www.amd.com/embeddedprocessors">http://www.amd.com/embeddedprocessors</a><br><br><br></blockquote></div><br><br clear="all"><br>-- <br>Otávio Alcântara<br>"I'll never cross to the Dark Side."