svn co svn://coreboot.org/coreboot/trunk coreboot<br><br><a href="http://www.coreboot.org/Build_HOWTO">http://www.coreboot.org/Build_HOWTO</a><br><br>Mvh Anders<br><br>----- Reply message -----<br>Fra: "Oliver Schinagl" <oliver@schinagl.nl><br>Dato: tor., maj 20, 2010 22:30<br>Emne: [coreboot] Indtast Bcc  Wyse S10 and coreboot<br>Til: <coreboot@coreboot.org><br><br>On 05/20/2010 09:48 PM, Anders Jenbo wrote:<br>> Heres a few lines to test erase and restore every thing.<br>><br>> sudo flashrom -r S10.rom<br>> sudo rm ignoreme.txt<br>> sudo flashrom -E -V>  flashrom-erase-SST49LF016C.txt<br>> sudo flashrom -w S10.rom<br>><br>> But i think there might actually be more to testing erase, then just<br>> erasing via the normal flashrom.<br>><br>> Take a full picture of the board and note posible revision numbers.<br>><br>> Try compiling the S50 code and flash the content to your bios. It seams<br>> that there is no com port so you will need a USB debug device if you<br>> want to debug the boot process.<br>>    <br>Oh yeah, I forgot to ask; 'compile' how? Is there a good wiki page?<br>> If it doesn't work then all you have to do is boot up another S10, pull<br>> out it's bios (while the system is on), plug in the bad bios, and flash<br>> your S10.rom image to it, and then place one of them in the other board.<br>><br>> if your rom looks like this<br>> <a href="http://www.flashrom.org/images/thumb/8/85/Plcc32_in_socket.jpg/180px-Plcc32_in_socket.jpg">http://www.flashrom.org/images/thumb/8/85/Plcc32_in_socket.jpg/180px-Plcc32_in_socket.jpg</a><br>> then it is recomented to glue push pins on top of them, to pull them out<br>> with out issues, using super glue. Like this<br>> <a href="http://www.flashrom.org/images/thumb/b/b8/Pushpin_roms_2.jpg/800px-Pushpin_roms_2.jpg">http://www.flashrom.org/images/thumb/b/b8/Pushpin_roms_2.jpg/800px-Pushpin_roms_2.jpg</a><br>> It is still posible to break off the push pin if you can't fit it in the<br>> small computer when you are done.<br>><br>><br>> -Anders<br>><br>><br>> tor, 20 05 2010 kl. 20:20 +0200, skrev Oliver Schinagl:<br>>    <br>>> Right,<br>>><br>>> I saw on the wiki that the S50 was tested etc, so it should be "supported".<br>>><br>>> The bios is socketed! I can take some foto's next week for the wiki if<br>>> desired!<br>>><br>>> I have attached several documents from the several commands. These<br>>> commands where run on an Ubuntu 10.04 from a USB stick. It took about 10<br>>> minutes to start, but runs reasonable well  :)<br>>><br>>> Flashrom.txt lists flashrom -V; on a sidenote, since I have several of<br>>> these terminals, and I can 'hotswap' I could test the erase thing? How<br>>> would this work and how would I recover if it goes bad. I'm willing to<br>>> try if you give me detailed instructions :)<br>>><br>>> Superiotool didn't report anything interesting; there is no superio chip :)<br>>><br>>> I also attached lspci -vvvxxx and dmesg aswell as cpuinfo<br>>><br>>> To recap; I think it's an AMD Geode GX2 or LX, with an CS5536 'companion<br>>> chip'.<br>>><br>>> The audiochip isn't anything special; it's an ACL655 and the network is<br>>> powerd by an RTL8100CL.<br>>><br>>><br>>> What I'm hoping, is using someting like bayou to boot either whatever is<br>>> stored on the local 'hdd' or boot an PXE image. USB would be handy too I<br>>> suppose :)<br>>><br>>> Thanks for your time again;<br>>><br>>> Oliver<br>>><br>>><br>>> On 05/20/2010 07:27 PM, anders@jenbo.dk wrote:<br>>>      <br>>>> Can the BIOS be swapped (is it socketed), do you have a spare (or one<br>>>> you fan borrow from motherboard) .<br>>>> Is the board using a supported or documented SuperIO (use superiotool,<br>>>> the manual, the we or your eyes to see what chip you have).<br>>>> Is the southbridg supported.<br>>>> Is the northbridg supported.<br>>>><br>>>> Mvh Anders<br>>>><br>>>> ----- Reply message -----<br>>>> Fra: "Oliver Schinagl"<oliver@schinagl.nl><br>>>> Dato: tor., maj 20, 2010 18:28<br>>>> Emne: [coreboot] Wyse S10 and coreboot<br>>>> Til:<coreboot@coreboot.org><br>>>><br>>>> Hello all,<br>>>><br>>>> I am very interested in starting to play with coreboot and use it on<br>>>> some of my systems. I have been interested in coreboot and following it<br>>>> for a few years now.<br>>>><br>>>> I'll skip the chit chat and get straight to it. I got my hands on a few<br>>>> Wyse S10 thinclients, and they work quite well, booting via PXE or USB.<br>>>> Recently, I found some cheap Disk on Module 44pin 'ssd' and wanted to<br>>>> try them out in the S10.<br>>>><br>>>> Unforuntatly, I'm getting an error when trying to run someting from it;<br>>>> that the IDE port has been disabled.<br>>>><br>>>> Since getting a bios upgrade (which might not fix it) is a very tedious<br>>>> task; i decided to look at coreboot.<br>>>><br>>>> My question is, I suppose quite simple; Where do I start?<br>>>><br>>>> Thanks,<br>>>><br>>>> Oliver<br>>>><br>>>> -- <br>>>> coreboot mailing list: coreboot@coreboot.org<br>>>> <a href="http://www.coreboot.org/mailman/listinfo/coreboot">http://www.coreboot.org/mailman/listinfo/coreboot</a><br>>>><br>>>><br>>>>        <br>>> -- <br>>> coreboot mailing list: coreboot@coreboot.org<br>>> <a href="http://www.coreboot.org/mailman/listinfo/coreboot">http://www.coreboot.org/mailman/listinfo/coreboot</a><br>>>      <br>><br>>    <br><br><br>-- <br>coreboot mailing list: coreboot@coreboot.org<br><a href="http://www.coreboot.org/mailman/listinfo/coreboot">http://www.coreboot.org/mailman/listinfo/coreboot</a><br><br><br>