This adds the m2v directory and necessary files to src/mainboards/asus and
adjusts the Kconfig.

Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>

---

Index: src/mainboard/asus/Kconfig
===================================================================
--- src/mainboard/asus/Kconfig.orig	2010-11-07 01:19:21.000000000 +0100
+++ src/mainboard/asus/Kconfig	2010-11-07 01:44:51.000000000 +0100
@@ -25,6 +25,8 @@
 	bool "A8N-E"
 config BOARD_ASUS_A8V_E_SE
 	bool "A8V-E SE"
+config BOARD_ASUS_M2V
+	bool "M2V"
 config BOARD_ASUS_M2V_MX_SE
 	bool "M2V-MX SE"
 config BOARD_ASUS_M4A785M
@@ -50,6 +52,7 @@
 
 source "src/mainboard/asus/a8n_e/Kconfig"
 source "src/mainboard/asus/a8v-e_se/Kconfig"
+source "src/mainboard/asus/m2v/Kconfig"
 source "src/mainboard/asus/m2v-mx_se/Kconfig"
 source "src/mainboard/asus/m4a785-m/Kconfig"
 source "src/mainboard/asus/mew-am/Kconfig"
Index: src/mainboard/asus/m2v/devicetree.cb
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ src/mainboard/asus/m2v/devicetree.cb	2010-11-07 01:44:51.000000000 +0100
@@ -0,0 +1,74 @@
+chip northbridge/amd/amdk8/root_complex		# Root complex
+  device lapic_cluster 0 on			# APIC cluster
+    chip cpu/amd/socket_AM2			# CPU
+      device lapic 0 on end			# APIC
+    end
+  end
+  device pci_domain 0 on			# PCI domain
+    chip northbridge/amd/amdk8			# mc0
+      device pci 18.0 on			# Northbridge
+        # Devices on link 0, link 0 == LDT 0
+        chip southbridge/via/vt8237r		# Southbridge
+          register "ide0_enable" = "1"		# Enable IDE channel 0
+          register "ide1_enable" = "1"		# Enable IDE channel 1
+          register "ide0_80pin_cable" = "1"	# 80pin cable on IDE channel 0
+          register "ide1_80pin_cable" = "1"	# 80pin cable on IDE channel 1
+          register "fn_ctrl_lo" = "0xc0"	# Enable SB functions
+          register "fn_ctrl_hi" = "0x0d"	# Enable SB functions
+          device pci 0.0 on end			# HT
+          device pci f.1 on end			# IDE
+          device pci 11.0 on			# LPC
+            chip drivers/generic/generic	# DIMM 0-0-0
+              device i2c 50 on end
+            end
+            chip drivers/generic/generic	# DIMM 0-0-1
+              device i2c 51 on end
+            end
+            chip drivers/generic/generic	# DIMM 0-1-0
+              device i2c 52 on end
+            end
+            chip drivers/generic/generic	# DIMM 0-1-1
+              device i2c 53 on end
+            end
+            chip superio/ite/it8712f		# Super I/O
+              device pnp 2e.0 on		# Floppy
+                io 0x60 = 0x3f0
+                irq 0x70 = 6
+                drq 0x74 = 2
+              end
+              device pnp 2e.1 on		# Com1
+                io 0x60 = 0x3f8
+                irq 0x70 = 4
+              end
+              device pnp 2e.2 off end		# Com2 (N/A on this board)
+              device pnp 2e.3 on		# Lpt1
+                io 0x60 = 0x378
+                irq 0x70 = 7
+                drq 0x74 = 3
+              end
+              device pnp 2e.4 on		# Environment controller
+                io 0x60 = 0xd00
+                io 0x62 = 0xc00
+                irq 0x70 = 0x00
+              end
+              device pnp 2e.5 off end		# PS/2 keyboard
+              device pnp 2e.6 off end		# PS/2 mouse
+              device pnp 2e.7 off end		# GPIO config
+              device pnp 2e.8 off end		# Midi port
+              device pnp 2e.9 off end		# Game port
+              device pnp 2e.a off end		# IR
+            end
+          end
+          device pci 12.0 off end		# VIA LAN (off, other chip used)
+          device pci 13.0 on end		# br
+          device pci 13.1 on end		# br2, need to have it here to discover it
+        end
+        chip southbridge/via/k8t890		# "Southbridge" K8T890
+        end
+      end
+      device pci 18.1 on end
+      device pci 18.2 on end
+      device pci 18.3 on end
+    end
+  end
+end
Index: src/mainboard/asus/m2v/Kconfig
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ src/mainboard/asus/m2v/Kconfig	2010-11-07 12:20:29.000000000 +0100
@@ -0,0 +1,77 @@
+if BOARD_ASUS_M2V
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+	def_bool y
+	select ARCH_X86
+	select CPU_AMD_SOCKET_AM2
+	select DIMM_DDR2
+	select QRANK_DIMM_SUPPORT
+	select HAVE_OPTION_TABLE
+	select K8_HT_FREQ_1G_SUPPORT
+	select NORTHBRIDGE_AMD_AMDK8
+	select NORTHBRIDGE_AMD_AMDK8_ROOT_COMPLEX
+	select SOUTHBRIDGE_VIA_VT8237R
+	select SOUTHBRIDGE_VIA_K8T890
+	select SUPERIO_ITE_IT8712F
+	select CACHE_AS_RAM
+	select BOARD_ROMSIZE_KB_512
+	select RAMINIT_SYSINFO
+	select TINY_BOOTBLOCK
+
+config MAINBOARD_DIR
+	string
+	default asus/m2v
+
+config DCACHE_RAM_BASE
+	hex
+	default 0xcc000
+
+config DCACHE_RAM_SIZE
+	hex
+	default 0x4000
+
+config DCACHE_RAM_GLOBAL_VAR_SIZE
+	hex
+	default 0x1000
+
+config APIC_ID_OFFSET
+	hex
+	default 0x10
+
+config SB_HT_CHAIN_ON_BUS0
+	int
+	default 1
+
+config MAINBOARD_PART_NUMBER
+	string
+	default "M2V"
+
+config HW_MEM_HOLE_SIZEK
+	hex
+	default 0
+
+config MAX_CPUS
+	int
+	default 2
+
+config MAX_PHYSICAL_CPUS
+	int
+	default 1
+
+config HEAP_SIZE
+	hex
+	default 0x40000
+
+config HT_CHAIN_END_UNITID_BASE
+	hex
+	default 0x20
+
+config HT_CHAIN_UNITID_BASE
+	hex
+	default 0x0
+
+config MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+	hex
+	default 0x1043
+
+endif # BOARD_ASUS_M2V
Index: src/mainboard/asus/m2v/romstage.c
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ src/mainboard/asus/m2v/romstage.c	2010-11-07 01:44:51.000000000 +0100
@@ -0,0 +1,299 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2006 AMD
+ * (Written by Yinghai Lu <yinghailu@amd.com> for AMD)
+ * Copyright (C) 2006 MSI
+ * (Written by Bingxun Shi <bingxunshi@gmail.com> for MSI)
+ * Copyright (C) 2008 Rudolf Marek <r.marek@assembler.cz>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+unsigned int get_sbdn(unsigned bus);
+
+/* Used by init_cpus and fidvid */
+#define SET_FIDVID 1
+
+/* If we want to wait for core1 done before DQS training, set it to 0. */
+#define SET_FIDVID_CORE0_ONLY 1
+
+#if CONFIG_K8_REV_F_SUPPORT == 1
+#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
+#endif
+
+#include <stdint.h>
+#include <string.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <cpu/amd/mtrr.h>
+#include <cpu/x86/lapic.h>
+#include <pc80/mc146818rtc.h>
+#include <console/console.h>
+#include <cpu/amd/model_fxx_rev.h>
+#include "northbridge/amd/amdk8/raminit.h"
+#include "cpu/amd/model_fxx/apic_timer.c"
+#include "lib/delay.c"
+#include "northbridge/amd/amdk8/reset_test.c"
+#include "northbridge/amd/amdk8/debug.c"
+#include "superio/ite/it8712f/it8712f_early_serial.c"
+#include "southbridge/via/vt8237r/vt8237r_early_smbus.c"
+#include "cpu/x86/mtrr/earlymtrr.c"
+#include "cpu/x86/bist.h"
+#include "northbridge/amd/amdk8/setup_resource_map.c"
+
+#define SERIAL_DEV PNP_DEV(0x2e, IT8712F_SP1)
+#define WATCHDOG_DEV PNP_DEV(0x2e, IT8712F_GPIO)
+
+#define IT8712F_GPIO_BASE		0x0a20
+
+static void memreset(int controllers, const struct mem_controller *ctrl)
+{
+}
+
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+	return smbus_read_byte(device, address);
+}
+
+static void activate_spd_rom(const struct mem_controller *ctrl)
+{
+}
+
+// defines S3_NVRAM_EARLY:
+#include "southbridge/via/k8t890/k8t890_early_car.c"
+
+#include "northbridge/amd/amdk8/amdk8.h"
+#include "northbridge/amd/amdk8/incoherent_ht.c"
+#include "northbridge/amd/amdk8/coherent_ht.c"
+#include "northbridge/amd/amdk8/raminit_f.c"
+#include "lib/generic_sdram.c"
+
+#include "cpu/amd/dualcore/dualcore.c"
+
+#include "cpu/amd/car/post_cache_as_ram.c"
+#include "cpu/amd/model_fxx/init_cpus.c"
+#include "cpu/amd/model_fxx/fidvid.c"
+#include "northbridge/amd/amdk8/resourcemap.c"
+
+void soft_reset(void)
+{
+	uint8_t tmp;
+
+	set_bios_reset();
+	print_debug("soft reset\n");
+
+	/* PCI reset */
+	tmp = pci_read_config8(PCI_DEV(0, 0x11, 0), 0x4f);
+	tmp |= 0x01;
+	/* FIXME from S3 set bit1 to disable USB reset VT8237A/S */
+	pci_write_config8(PCI_DEV(0, 0x11, 0), 0x4f, tmp);
+
+	while (1) {
+		/* daisy daisy ... */
+		hlt();
+	}
+}
+
+unsigned int get_sbdn(unsigned bus)
+{
+	device_t dev;
+
+	dev = pci_locate_device_on_bus(PCI_ID(PCI_VENDOR_ID_VIA,
+					PCI_DEVICE_ID_VIA_VT8237R_LPC), bus);
+	return (dev >> 15) & 0x1f;
+}
+
+struct gpio_init_val {
+	u8 addr;
+	u8 val;
+};
+
+static const struct gpio_init_val gpio_init_data[] = {
+	/* multi-function pin selection */
+	{ 0x25, 0x00 },
+	{ 0x28, 0x00 }, /* gp46 is infrared receive input */
+	{ 0x29, 0x40 }, /* reserved value?!? */
+	{ 0x2a, 0x00 },
+	{ 0x2c, 0x1d }, /* pin91 is VIN7 instead of PCIRSTIN# */
+	/* gpio i/o port base */
+	{ 0x62, IT8712F_GPIO_BASE >> 8 },
+	{ 0x63, IT8712F_GPIO_BASE & 0xff },
+	/* 0xb8 - 0xbc: gpio pull-up enable */
+	{ 0xb8, 0x00 },
+	/* 0xc0 - 0xc4: gpio alternate function select */
+	{ 0xc0, 0x00 },
+	{ 0xc3, 0x00 },
+	{ 0xc4, 0xc0 },
+	/* 0xc8 - 0xcc: gpio output enable */
+	{ 0xc8, 0x00 },
+	{ 0xcb, 0x00 },
+	{ 0xcc, 0xc0 },
+	/* end of list */
+	{ 0, 0 },
+};
+
+static void m2v_it8712f_gpio_init(void)
+{
+	const struct gpio_init_val *giv;
+
+	printk(BIOS_SPEW, "it8712f gpio init...\n");
+
+	/*
+	 * it8712f gpio config
+	 *
+	 * Most importantly this switches pin 91 from
+	 * PCIRSTIN# to VIN7.
+	 * Note that only PCIRST3# and PCIRST5# are affected
+	 * by PCIRSTIN#, the PCIRST1#, PCIRST2#, PCIRST4# are always
+	 * direct buffers of #LRESET (low pin count bus reset).
+	 * If this is not done All PCIRST are in reset state and the
+	 * pcie slots don't initialize.
+	 *
+	 * pci reset handling:
+	 * pin 91: VIN7 (alternate PCIRSTIN#)
+	 * pin 48: PCIRST5# / gpio port 5 bit 0
+	 * pin 84: PCIRST4# / gpio port 1 bit 0
+	 * pin 31: PCIRST1# / gpio port 1 bit 4
+	 * pin 33: PCIRST2# / gpio port 1 bit 2
+	 * pin 34: PCIRST3# / gpio port 1 bit 1
+	 *
+	 * PCIRST[0-5]# are connected as follows:
+	 * pcirst1# -> pci bus
+	 * pcirst2# -> ide bus
+	 * pcirst3# -> pcie devices
+	 * pcirst4# -> pcie graphics
+	 * pcirst5# -> maybe n/c (untested)
+	 *
+	 * For software control of PCIRST[1-5]#:
+	 * 0x2a=0x17 (deselect pcirst# hardwiring, enable 0x25 control)
+	 * 0x25=0x17 (select gpio function)
+	 * 0xc0=0x17, 0xc8=0x17 gpio port 1 select & output enable
+	 * 0xc4=0xc1, 0xcc=0xc1 gpio port 5 select & output enable
+	 */
+	it8712f_enter_conf();
+	giv = gpio_init_data;
+	while (giv->addr) {
+		printk(BIOS_SPEW, "it8712f gpio: %02x=%02x\n",
+				giv->addr, giv->val);
+		it8712f_sio_write(IT8712F_GPIO, giv->addr, giv->val);
+		giv++;
+	}
+	it8712f_exit_conf();
+}
+
+static void m2v_bus_init(void)
+{
+	device_t dev;
+
+	printk(BIOS_SPEW, "m2v_bus_init\n");
+
+	dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
+				PCI_DEVICE_ID_VIA_K8T890CF_0), 0);
+	pci_write_config8(dev, K8T890_MULTIPLE_FN_EN, 0x01);
+
+	dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
+				PCI_DEVICE_ID_VIA_K8T890CF_5), 0);
+	/*
+	 * bit | meaning
+	 * 6   | 0: hide scratch register function 0:0.6 (we don't use it)
+	 * 5   | 1: enable pcie bridge 0:2.0
+	 * 4   | 0: hide   pcie bridge 0:3.3 (not connected)
+	 * 3   | 1: enable pcie bridge 0:3.2
+	 * 2   | 1: enable pcie bridge 0:3.1
+	 * 1   | 1: enable pcie bridge 0:3.0
+	 */
+	pci_write_config8(dev, 0xf0, 0x2e);
+}
+
+void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
+{
+	static const uint16_t spd_addr[] = {
+		// Node 0
+		(0xa << 3) | 0, (0xa << 3) | 2, 0, 0,
+		(0xa << 3) | 1, (0xa << 3) | 3, 0, 0,
+		// Node 1
+		(0xa << 3) | 4, (0xa << 3) | 6, 0, 0,
+		(0xa << 3) | 5, (0xa << 3) | 7, 0, 0,
+	};
+	unsigned bsp_apicid = 0;
+	int needs_reset = 0;
+	struct sys_info *sysinfo =
+	    (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
+
+	it8712f_24mhz_clkin();
+	it8712f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
+	it8712f_kill_watchdog();
+	uart_init();
+	console_init();
+	enable_rom_decode();
+	m2v_bus_init();
+	m2v_it8712f_gpio_init();
+
+	printk(BIOS_INFO, "now booting... \n");
+
+	if (bist == 0)
+		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
+
+	/* Halt if there was a built in self test failure. */
+	report_bist_failure(bist);
+	setup_default_resource_map();
+	setup_coherent_ht_domain();
+	wait_all_core0_started();
+
+	printk(BIOS_INFO, "now booting... All core 0 started\n");
+
+#if CONFIG_LOGICAL_CPUS==1
+	/* It is said that we should start core1 after all core0 launched. */
+	start_other_cores();
+	wait_all_other_cores_started(bsp_apicid);
+#endif
+	init_timer();
+	ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */
+
+	needs_reset = optimize_link_coherent_ht();
+	print_debug_hex8(needs_reset);
+	needs_reset |= optimize_link_incoherent_ht(sysinfo);
+	print_debug_hex8(needs_reset);
+	needs_reset |= k8t890_early_setup_ht();
+	print_debug_hex8(needs_reset);
+
+	if (needs_reset) {
+		printk(BIOS_DEBUG, "ht reset -\n");
+		soft_reset();
+		printk(BIOS_DEBUG, "FAILED!\n");
+	}
+
+	/* the HT settings needs to be OK, because link freq chnage may cause HT disconnect */
+	/* allow LDT STOP asserts */
+	vt8237_sb_enable_fid_vid();
+
+	enable_fid_change();
+	print_debug("after enable_fid_change\n");
+
+	init_fidvid_bsp(bsp_apicid);
+
+	/* Stop the APs so we can start them later in init. */
+	allow_all_aps_stop(bsp_apicid);
+
+	/* It's the time to set ctrl now. */
+	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
+	enable_smbus();
+	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
+	post_cache_as_ram();
+}
+
Index: src/mainboard/asus/m2v/cmos.layout
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ src/mainboard/asus/m2v/cmos.layout	2010-11-07 01:44:51.000000000 +0100
@@ -0,0 +1,98 @@
+entries
+
+#start-bit length  config config-ID    name
+#0            8       r       0        seconds
+#8            8       r       0        alarm_seconds
+#16           8       r       0        minutes
+#24           8       r       0        alarm_minutes
+#32           8       r       0        hours
+#40           8       r       0        alarm_hours
+#48           8       r       0        day_of_week
+#56           8       r       0        day_of_month
+#64           8       r       0        month
+#72           8       r       0        year
+#80           4       r       0        rate_select
+#84           3       r       0        REF_Clock
+#87           1       r       0        UIP
+#88           1       r       0        auto_switch_DST
+#89           1       r       0        24_hour_mode
+#90           1       r       0        binary_values_enable
+#91           1       r       0        square-wave_out_enable
+#92           1       r       0        update_finished_enable
+#93           1       r       0        alarm_interrupt_enable
+#94           1       r       0        periodic_interrupt_enable
+#95           1       r       0        disable_clock_updates
+#96         288       r       0        temporary_filler
+0          384       r       0        reserved_memory
+384          1       e       4        boot_option
+385          1       e       4        last_boot
+386          1       e       1        ECC_memory
+388          4       r       0        reboot_bits
+392          3       e       5        baud_rate
+395          1       e       1        hw_scrubber
+396          1       e       1        interleave_chip_selects
+397          2       e       8        max_mem_clock
+399         1       e       2        multi_core
+400          1       e       1        power_on_after_fail
+412          4       e       6        debug_level
+416          4       e       7        boot_first
+420          4       e       7        boot_second
+424          4       e       7        boot_third
+428          4       h       0        boot_index
+432         8       h       0        boot_countdown
+440          4       e       9        slow_cpu
+444          1       e       1        nmi
+445          1       e       1        iommu
+728        256       h       0        user_data
+984         16       h       0        check_sum
+# Reserve the extended AMD configuration registers
+1000        24       r       0        amd_reserved
+
+
+
+enumerations
+
+#ID value   text
+1     0     Disable
+1     1     Enable
+2     0     Enable
+2     1     Disable
+4     0     Fallback
+4     1     Normal
+5     0     115200
+5     1     57600
+5     2     38400
+5     3     19200
+5     4     9600
+5     5     4800
+5     6     2400
+5     7     1200
+6     6     Notice
+6     7     Info
+6     8     Debug
+6     9     Spew
+7     0     Network
+7     1     HDD
+7     2     Floppy
+7     8     Fallback_Network
+7     9     Fallback_HDD
+7     10    Fallback_Floppy
+#7     3     ROM
+8     0     DDR400
+8     1     DDR333
+8     2     DDR266
+8     3     DDR200
+9     0     off
+9     1     87.5%
+9     2     75.0%
+9     3     62.5%
+9     4     50.0%
+9     5     37.5%
+9     6     25.0%
+9     7     12.5%
+
+checksums
+
+checksum 392 983 984
+
+
Index: src/mainboard/asus/m2v/chip.h
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ src/mainboard/asus/m2v/chip.h	2010-11-07 01:44:51.000000000 +0100
@@ -0,0 +1,22 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 Rudolf Marek <r.marek@assembler.cz>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+extern struct chip_operations mainboard_ops;
+
+struct mainboard_config {};
Index: src/mainboard/asus/m2v/mainboard.c
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ src/mainboard/asus/m2v/mainboard.c	2010-11-07 01:44:51.000000000 +0100
@@ -0,0 +1,25 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2010 Tobias Diedrich <ranma+coreboot@tdiedrich.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#include <device/device.h>
+#include "chip.h"
+
+struct chip_operations mainboard_ops = {
+	CHIP_NAME("ASUS M2V")
+};



