I got some old boxes:  tyan s2882-d, dual opteron processors, 16G RAM. 512K bios flash. <br><br>So far, I am not able to get it to boot. It appears to reboot during CPU init. <br><br>If anyone got coreboot working on this board, which revision did it worked last ? <br>
<br><br>Serial console: <br><br>coreboot-4.0-3129-gefb7940 Fri Nov 30 22:50:45 PST 2012 starting...<br>Enabling routing table for node 00 done.<br>Enabling SMP settings<br>(0,1) link=01<br>(1,0) link=01<br>setup_remote_node: done<br>
Renaming current temporary node to 01 done.<br>Enabling routing table for node 01 done.<br>02 nodes initialized.<br>coherent_ht_finalize<br>done<br>SBLink=00<br>NC node|link=00<br>entering ht_optimize_link<br>pos=0x8a, unfiltered freq_cap=0x8075<br>
pos=0x8a, filtered freq_cap=0x75<br>pos=0xce, unfiltered freq_cap=0x35<br>freq_cap1=0x75, freq_cap2=0x15<br>dev1 old_freq=0x4, freq=0x4, needs_reset=0x0<br>dev2 old_freq=0x4, freq=0x4, needs_reset=0x0<br>width_cap1=0x11, width_cap2=0x11<br>
dev1 input ln_width1=0x4, ln_width2=0x4<br>dev1 input width=0x1<br>dev1 output ln_width1=0x4, ln_width2=0x4<br>dev1 input|output width=0x11<br>old dev1 input|output width=0x11<br>dev2 input|output width=0x11<br>old dev2 input|output width=0x11<br>
entering ht_optimize_link<br>pos=0xd2, unfiltered freq_cap=0x35<br>pos=0xce, unfiltered freq_cap=0x1<br>pos=0xce, filtered freq_cap=0x1<br>freq_cap1=0x15, freq_cap2=0x1<br>dev1 old_freq=0x0, freq=0x0, needs_reset=0x0<br>dev2 old_freq=0x0, freq=0x0, needs_reset=0x0<br>
width_cap1=0x0, width_cap2=0x0<br>dev1 input ln_width1=0x3, ln_width2=0x3<br>dev1 input width=0x0<br>dev1 output ln_width1=0x3, ln_width2=0x3<br>dev1 input|output width=0x0<br>old dev1 input|output width=0x0<br>dev2 input|output width=0x0<br>
old dev2 input|output width=0x0<br>SMBus controller enabled<br>Ram1.00<br>setting up CPU00 northbridge registers<br>done.<br>Ram1.01<br>setting up CPU01 northbridge registers<br>done.<br>Ram2.00<br>Enabling dual channel memory<br>
Registered<br>200MHz<br>Interleaved<br>RAM end at 0x00800000 kB<br>Handling memory mapped above 4 GB<br>Upper RAM end at 0x00800000 kB<br>Correcting memory amount mapped below 4 GB<br>Adjusting lower RAM end<br>Lower RAM end at 0x003f0000 kB<br>
Ram2.01<br>Enabling dual channel memory<br>Registered<br>200MHz<br>Interleaved<br>RAM end at 0x01000000 kB<br>Handling memory mapped above 4 GB<br>Upper RAM end at 0x01000000 kB<br>Correcting memory amount mapped below 4 GB<br>
Adjusting lower RAM end<br>Lower RAM end at 0x003f0000 kB<br>Ram3<br>ECC enabled<br>ECC enabled<br>Initializing memory:  done<br>Initializing memory:  done<br>Handling memory hole at 0x00300000 (default)<br>RAM end at 0x01100000 kB<br>
Handling memory mapped above 4 GB<br>Upper RAM end at 0x01100000 kB<br>Correcting memory amount mapped below 4 GB<br>Adjusting lower RAM end<br>Lower RAM end at 0x00300000 kB<br>Ram4<br>v_esp=000cff48<br>testx = 5a5a5a5a<br>
Copying data from cache to RAM -- switching to use RAM as stack... Done<br>testx = 5a5a5a5a<br>Disabling cache as ram now <br>Clearing initial memory region: Done<br>Loading image.<br>CBFS: Looking for 'fallback/coreboot_ram'<br>
CBFS: found.<br><br><br><br>INIT detected from  --- { APICID = 00 NODEID = 00 COREID = 00} ---<br><br>Issuing SOFT_RESET...<br><br>....<br><br>No error during make. I tried building on x86_64 and x86. <br><br><br>thanks<br>
Kui.Z<br><br><br><br><br><br>