<div>Hi, Martin, Daniel, Kyösti, Loic,<br></div><div>Hi, friends<br></div><div><br></div><div>The problem was in the programmer which programmed incorrectly.<br></div><div>Now I see the post codes and SeaBIOS works.<br></div><div>Also as you mentioned, it is important to put the memory in the slot furthest away from the processor,<br></div><div>I have only one memory module and otherwise the system doesn't work.<br></div><div><br></div><blockquote type="cite" class="protonmail_quote"><div>"As was mentioned by Daniel, you don't need  the external<br></div><div>card's VBIOS built into the rom.  If you're using SeaBIOS, it will<br></div><div>read the vbios directly from the card."<br></div></blockquote><div>You are right, in this case all is working, otherwise - doesn't (shouldn't use VGAbios from the Internet in my case).<br></div><div><br></div><div>Now my keyboard does not work (Logitech Y-UL76). I have tried in all slots (even using 10 pin to usb adapter).<br></div><div>The power seems to be there, because the mouse once blinked when it was connected-disconnected.<br></div><div>Usb settings enabled in config, as I understand. Please help to fix.<br></div><div><br></div><div>Here is my config and binary (attached to the e-mail).<br></div><div>Config: <a href="http://pastebin.com/BYgiLabA">http://pastebin.com/BYgiLabA</a><br></div><div><br></div><div>Thank you very much!<br></div><div>Maxim<br></div><div class="protonmail_signature_block "><div class="protonmail_signature_block-proton protonmail_signature_block-empty">Tried in all slots (even using adapter 10 pin usb)<br></div></div><div><br></div><blockquote class="protonmail_quote" type="cite"><div>-------- Original Message --------<br></div><div>Subject: Re: [coreboot] Coreboot binary for ASUS F2A85-M<br></div><div>Local Time: 24 Января 2017 г. 3:29 ночи<br></div><div>UTC Time: 24 Января 2017 г. 00:29<br></div><div>From: gaumless@gmail.com<br></div><div>To: Maxim Gusev <mail@maximgusev.com><br></div><div>Daniel Kulesz <daniel.ina1@googlemail.com>, coreboot@coreboot.org <coreboot@coreboot.org><br></div><div><br></div><div>Hi Maxim,<br></div><div>Try this:  Remove all of the memory in the board except for one DIMM<br></div><div>in the slot furthest away from the processor.  AGESA on this chip has<br></div><div>a requirement (that some vendors apparently worked around) that DIMMs<br></div><div>be populated from the furthest slot to the closest.<br></div><div><br></div><div>It looks like the code to route Port 80h to PCI isn't in that<br></div><div>chipset.  That's something we should check before giving that option.<br></div><div><br></div><div>As was mentioned by Daniel, you don't need (or want) the external<br></div><div>card's VBIOS built into the rom.  If you're using SeaBIOS, it will<br></div><div>read the vbios directly from the card.<br></div><div><br></div><div>If these steps don't help, I'll work with you to get a rom that boots for you.<br></div><div><br></div><div>Martin<br></div><div><br></div><div>On Mon, Jan 23, 2017 at 3:12 PM, Maxim Gusev via coreboot<br></div><div><coreboot@coreboot.org> wrote:<br></div><div>> Thank you for advise about pc speaker console! I will try it today.<br></div><div>> I am using CH341A programmer and its soft of 1.18 version. Also i am using<br></div><div>> the original WINBOND W25Q64BV 8mb chip.<br></div><div>> Yes, if I flash back the original UEFI ROM onto the chip - the system start<br></div><div>> up again.<br></div><div>><br></div><div>> Maxim<br></div><div>><br></div><div>><br></div><div>> -------- Original Message --------<br></div><div>> Subject: Re: [coreboot] Coreboot binary for ASUS F2A85-M<br></div><div>> Local Time: 23 Января 2017 г. 11:03 вечера<br></div><div>> UTC Time: 23 Января 2017 г. 20:03<br></div><div>> From: daniel.ina1@googlemail.com<br></div><div>> To: Maxim Gusev <mail@maximgusev.com><br></div><div>> coreboot@coreboot.org <coreboot@coreboot.org><br></div><div>><br></div><div>> My F2A85-M is currently down, so I can't test it with your config - sorry<br></div><div>> (but maybe in two days or so). But one more thing you could try is the pc<br></div><div>> speaker console:<br></div><div>><br></div><div>> https://www.coreboot.org/Spkmodem<br></div><div>><br></div><div>> At least, if it starts beeping this would be already a good sign.<br></div><div>><br></div><div>> Btw.: How did you actually flash coreboot onto the chip? And did you use the<br></div><div>> original BIOS chip? If not, did you make sure your other chip is also 8M in<br></div><div>> size? If you flash back the original ROM onto the chip - does the system<br></div><div>> start up again?<br></div><div>><br></div><div>> Cheers, Daniel<br></div><div>><br></div><div>><br></div><div>> On Mon, 23 Jan 2017 14:16:25 -0500<br></div><div>> Maxim Gusev <mail@maximgusev.com> wrote:<br></div><div>><br></div><div>>> I tried different ways to initialize the VGA card - does not work.<br></div><div>>> I also tried with your config file - did not work (as I remember, it was<br></div><div>>> further suggested in the manual mode to complete the configuration).<br></div><div>>> Here is my config file: http://pastebin.com/RVLcGku8<br></div><div>>> I have a feeling that coreboot is programmed or read (from the spi flash)<br></div><div>>> to the wrong address,<br></div><div>>> although it is unlikely because it is, as I understand it, is written in<br></div><div>>> the mainboard sources, and I never touched them.<br></div><div>>><br></div><div>>><br></div><div>>><br></div><div>>><br></div><div>>> -------- Original Message --------<br></div><div>>> Subject: Re: [coreboot] Coreboot binary for ASUS F2A85-M<br></div><div>>> Local Time: 23 Января 2017 г. 10:01 вечера<br></div><div>>> UTC Time: 23 Января 2017 г. 19:01<br></div><div>>> From: daniel.ina1@googlemail.com<br></div><div>>> To: Maxim Gusev <mail@maximgusev.com><br></div><div>>> Kyösti Mälkki <kyosti.malkki@gmail.com>, coreboot@coreboot.org<br></div><div>>> <coreboot@coreboot.org><br></div><div>>><br></div><div>>> On Mon, 23 Jan 2017 15:51:16 +0200<br></div><div>>> Kyösti Mälkki <kyosti.malkki@gmail.com> wrote:<br></div><div>>><br></div><div>>> > On Mon, Jan 23, 2017 at 2:41 PM, Maxim Gusev via coreboot <<br></div><div>>> > coreboot@coreboot.org> wrote:<br></div><div>>> ><br></div><div>>> > > Hi Daniel,<br></div><div>>> > ><br></div><div>>> > > Now I have compiled coreboot 4.5 with the SeaBIOS 1.9.3 as a payload<br></div><div>>> > > and<br></div><div>>> > > the VGAbios:<br></div><div>>> > > I am using the Asus EN8600GT as a videocard (PCIe) and I took out the<br></div><div>>> > > binary here:<br></div><div>>> > > https://www.techpowerup.com/vgabios/?architecture=&<br></div><div>>> > > manufacturer=Asus&model=8600+GT&interface=PCI-E&memType=&<br></div><div>>> > > memSize=256&since=<br></div><div>>> > ><br></div><div>>><br></div><div>>> To my understanding, when using an external graphics card you don't need<br></div><div>>> to extract or put any VGA blobs in. But you need to initialize the PCIe<br></div><div>>> video. Can you provide us with the full config you are using, please? Or did<br></div><div>>> you try my config which I linked in my initial answer? (There, it should be<br></div><div>>> already enabled as far as I remember)<br></div><div>>><br></div><div>>> > > Also I have turned on in console settings "Show POST codes...", but<br></div><div>>> > > there<br></div><div>>> > > is nothing works:(<br></div><div>>> > ><br></div><div>>> ><br></div><div>>> > You probably also need POST_DEVICE_PCI_PCIE set in your .config. In<br></div><div>>> > menuconfig: "Device to send POST codes to" -> "PCI/PCIe".<br></div><div>>> ><br></div><div>>> > As for the serial port: I think this mainboard is not a retail version,<br></div><div>>> > but<br></div><div>>> > came from ASUS Essentio Desktop PC CM1745.<br></div><div>>> ><br></div><div>>> > http://www.ascendtech.us/asus-f2a85-m-cm1745-dp-motherboard_i_mb90mibiw5g0xbn.aspx<br></div><div>>> ><br></div><div>>> > Looks like RS232 level translator ICs are also missing and some other<br></div><div>>> > differences on BOM too.<br></div><div>>> ><br></div><div>>><br></div><div>>> Indeed, there seem to be different versions of the board then. I have the<br></div><div>>> retail version, and mine has the connectors soldered. Can someone update the<br></div><div>>> wiki, please?<br></div><div>>><br></div><div>>> Cheers, Daniel<br></div><div>><br></div><div>><br></div><div>><br></div><div>> --<br></div><div>> coreboot mailing list: coreboot@coreboot.org<br></div><div>> https://www.coreboot.org/mailman/listinfo/coreboot<br></div></blockquote><div><br></div>