Difference between revisions of "Board:asrock/e350m1"
(28 intermediate revisions by 6 users not shown) | |||
Line 13: | Line 13: | ||
|CPU_multicore_status = OK | |CPU_multicore_status = OK | ||
|CPU_multicore_comments = Both cores seem to be detected. | |CPU_multicore_comments = Both cores seem to be detected. | ||
− | |CPU_virt_status = | + | |CPU_virt_status = OK |
|RAM_EDO_status = N/A | |RAM_EDO_status = N/A | ||
Line 35: | Line 35: | ||
|USB_comments = | |USB_comments = | ||
|Onboard_VGA_status = OK | |Onboard_VGA_status = OK | ||
− | |Onboard_VGA_comments = | + | |Onboard_VGA_comments = You must add a VGA BIOS image. Use the nomodeset kernel command line option if you get garbled output immediately after starting the Linux kernel. |
− | |Onboard_ethernet_status = | + | |Onboard_ethernet_status = OK |
− | |Onboard_ethernet_comments = | + | |Onboard_ethernet_comments = If the ethernet chip isn't detected after a reboot, use a current version of coreboot. |
|Onboard_audio_status = OK | |Onboard_audio_status = OK | ||
|Onboard_modem_status = N/A | |Onboard_modem_status = N/A | ||
Line 51: | Line 51: | ||
|AGP_cards_status = N/A | |AGP_cards_status = N/A | ||
|PCI_cards_status = N/A | |PCI_cards_status = N/A | ||
− | |PCIE_x1_status = | + | |PCIE_x1_status = OK |
+ | |PCIE_x1_comments = Works at least with this ath9k wifi card(I only tested that card) : 01:00.0 Network controller [0280]: Qualcomm Atheros AR9485 Wireless Network Adapter [168c:0032] (rev 01). Also tested with an TI Firewire host controller (XIO2200) and an Intel gigabit ethernet card (82574). | ||
|PCIE_x2_status = N/A | |PCIE_x2_status = N/A | ||
|PCIE_x4_status = N/A | |PCIE_x4_status = N/A | ||
|PCIE_x8_status = N/A | |PCIE_x8_status = N/A | ||
− | |PCIE_x16_status = | + | |PCIE_x16_status = OK |
− | |PCIE_x16_comments = | + | |PCIE_x16_comments = tested with a Radeon HD2600, but only video output after linux boot |
|PCIE_x32_status = N/A | |PCIE_x32_status = N/A | ||
|HTX_status = N/A | |HTX_status = N/A | ||
Line 63: | Line 64: | ||
|COM1_status = OK | |COM1_status = OK | ||
|COM2_status = N/A | |COM2_status = N/A | ||
− | |PS2_keyboard_status = | + | |PS2_keyboard_status = WIP |
+ | |PS2_keyboard_comments = keyboard works under seabios and grub, but not under linux | ||
|PS2_mouse_status = Untested | |PS2_mouse_status = Untested | ||
+ | |PS2_mouse_comments = simultaneous use of PS/2 keyboard and mouse with a Y-cable would require a small hardware mod (2 additional 0 ohms resistors) | ||
|PP_status = N/A | |PP_status = N/A | ||
|PP_comments = | |PP_comments = | ||
Line 72: | Line 75: | ||
|DiskOnChip_status = N/A | |DiskOnChip_status = N/A | ||
− | |Sensors_status = | + | |Sensors_status = WIP |
− | |Sensors_comments = CPU temperature seems to be displayed properly by lm-sensors. | + | |Sensors_comments = The CPU temperature seems to be displayed properly by lm-sensors. Fan control is not implemented. |
|CAN_bus_status = N/A | |CAN_bus_status = N/A | ||
− | |CPUfreq_status = | + | |CPUfreq_status = OK |
− | |CPUfreq_comments = | + | |CPUfreq_comments = The ondemand governor works by default. |
− | |Powersave_status = | + | |Powersave_status = OK |
− | |Powersave_comments = | + | |Powersave_comments = By default the CPU fan rotates at maximum speed. See the fancontrol attachment below on how to get it adjust automatically depending on CPU temperature. |
|ACPI_status = ? | |ACPI_status = ? | ||
|ACPI_comments = | |ACPI_comments = | ||
|Reboot_status = OK | |Reboot_status = OK | ||
|Poweroff_status = OK | |Poweroff_status = OK | ||
+ | |Suspend_status = NO | ||
+ | |Suspend_comments = The machine suspends but it fails to resume from suspend. | ||
|LEDs_status = N/A | |LEDs_status = N/A | ||
|HPET_status = Unknown | |HPET_status = Unknown | ||
Line 93: | Line 98: | ||
}} | }} | ||
+ | |||
+ | == Original BIOS information gathering == | ||
+ | |||
+ | Dumps of information gathered by various commands while running the proprietary BIOS are available here: [[File:ASRock_E350M1_info_dump.tar.bz2]] | ||
+ | |||
+ | == Hardware == | ||
+ | |||
+ | The ROM chip is not soldered to the board but socketed. You can buy replacement (exact ROM chip for E350M1 or empty ones). See http://flashrom.org/Technology#DIP8:_Dual_In-line_Package.2C_8_pins and http://www.bios-chip24.com/Asrock-E350M1/en. | ||
+ | |||
+ | GPP PCIe ports on the FCH: | ||
+ | :port 0: mini PCIe slot | ||
+ | :port 1: ethernet chip | ||
+ | :port 2: UBS3 chip | ||
+ | :port 3: unconnected | ||
+ | |||
+ | GPP CLK ports on the FCH: | ||
+ | :port 0: mini PCIe slot | ||
+ | :port 1: ethernet chip | ||
+ | :port 2: UBS3 chip | ||
+ | :port 3: unconnected | ||
+ | :port 4: unconnected | ||
+ | :port 5: unconnected | ||
+ | :port 6: unconnected | ||
+ | :port 7: unconnected | ||
+ | :port 8: unconnected | ||
+ | |||
+ | GPP GFX SLT clock: | ||
+ | :PCIe card | ||
+ | |||
+ | PERST# for ethernet chip and mini PCIe card are connected to RSTOUT1# pin of the NCT5572D. | ||
+ | |||
+ | The SLP_S3# and SLP_S5# outputs of the FCH are connected to the corresponding inputs of the SIO. | ||
+ | |||
+ | [[Media:E350m1_sio_connections_partial.zip|Incomplete list of the connections to the SuperIO-chip]] | ||
+ | |||
+ | == Temperature and fan control == | ||
+ | Fan control is currently unimplemented in coreboot. Still it can be done in GNU/Linux. | ||
+ | |||
+ | Note that the mainboard manual states that only the CPU_FAN1 connector supports fan control. | ||
+ | |||
+ | Fancontrol configuration file for adjusting the CPU fan speed dynamically: [[File:Fancontrol.gz]] | ||
+ | === /etc/fancontrol for trisquel === | ||
+ | # Configuration file generated by pwmconfig, changes will be lost | ||
+ | INTERVAL=10 | ||
+ | DEVPATH=hwmon0=devices/pci0000:00/0000:00:18.3 hwmon1=devices/platform/w83627ehf.656 | ||
+ | DEVNAME=hwmon0=k10temp hwmon1=nct6775 | ||
+ | FCTEMPS=hwmon1/device/pwm2=hwmon0/device/temp1_input | ||
+ | FCFANS= hwmon1/device/pwm2=hwmon1/device/fan2_input | ||
+ | MINTEMP=hwmon1/device/pwm2=60 | ||
+ | MAXTEMP=hwmon1/device/pwm2=65 | ||
+ | MINSTART=hwmon1/device/pwm2=90 | ||
+ | MINSTOP=hwmon1/device/pwm2=75 | ||
+ | MINPWM=hwmon1/device/pwm2=0 | ||
+ | MAXPWM=hwmon1/device/pwm2=255 | ||
+ | |||
+ | === /etc/fancontrol for GNU/Linux Debian 8 === | ||
+ | INTERVAL=10 | ||
+ | DEVPATH=hwmon2=devices/pci0000:00/0000:00:18.3 hwmon1=devices/platform/w83627ehf.656 | ||
+ | DEVNAME=hwmon2=k10temp hwmon1=nct6775 | ||
+ | FCTEMPS=hwmon1/device/pwm2=hwmon2/device/temp1_input | ||
+ | MINTEMP=hwmon1/device/pwm2=40 | ||
+ | MAXTEMP=hwmon1/device/pwm2=65 | ||
+ | MINSTART=hwmon1/device/pwm2=128 | ||
+ | MINSTOP=hwmon1/device/pwm2=57 | ||
+ | FCFANS=hwmon1/device/pwm2=hwmon1/device/fan2_input |
Latest revision as of 12:13, 20 May 2015
Contents
Status
Device/functionality | Status | Comments | ||||||
---|---|---|---|---|---|---|---|---|
CPU | ||||||||
CPU works | OK | |||||||
L1 cache enabled | OK | |||||||
L2 cache enabled | OK | |||||||
L3 cache enabled | N/A | |||||||
Multiple CPU support | N/A | |||||||
Multi-core support | OK | Both cores seem to be detected. | ||||||
Hardware virtualization | OK | |||||||
RAM | ||||||||
EDO | N/A | |||||||
SDRAM | N/A | |||||||
SO-DIMM | N/A | |||||||
DDR | N/A | |||||||
DDR2 | N/A | |||||||
DDR3 | OK | |||||||
Dual channel support | N/A | |||||||
ECC support | N/A | |||||||
On-board Hardware | ||||||||
On-board IDE 3.5" | N/A | |||||||
On-board IDE 2.5" | N/A | |||||||
On-board SATA | OK | |||||||
On-board SCSI | N/A | |||||||
On-board USB | OK | |||||||
On-board VGA | OK | You must add a VGA BIOS image. Use the nomodeset kernel command line option if you get garbled output immediately after starting the Linux kernel. | ||||||
On-board Ethernet | OK | If the ethernet chip isn't detected after a reboot, use a current version of coreboot. | ||||||
On-board Audio | OK | |||||||
On-board Modem | N/A | |||||||
On-board FireWire | N/A | |||||||
On-board Smartcard reader | N/A | |||||||
On-board CompactFlash | N/A | |||||||
On-board PCMCIA | N/A | |||||||
On-board Wifi | N/A | |||||||
On-board Bluetooth | N/A | |||||||
On-board SD card reader | N/A | |||||||
Add-on slots/cards | ||||||||
ISA add-on cards | N/A | |||||||
Audio/Modem-Riser (AMR/CNR) cards | N/A | |||||||
PCI add-on cards | N/A | |||||||
Mini-PCI add-on cards | N/A | |||||||
Mini-PCI-Express add-on cards | Unknown | |||||||
PCI-X add-on cards | N/A | |||||||
AGP graphics cards | N/A | |||||||
PCI Express x1 add-on cards | OK | Works at least with this ath9k wifi card(I only tested that card) : 01:00.0 Network controller [0280]: Qualcomm Atheros AR9485 Wireless Network Adapter [168c:0032] (rev 01). Also tested with an TI Firewire host controller (XIO2200) and an Intel gigabit ethernet card (82574). | ||||||
PCI Express x2 add-on cards | N/A | |||||||
PCI Express x4 add-on cards | N/A | |||||||
PCI Express x8 add-on cards | N/A | |||||||
PCI Express x16 add-on cards | OK | tested with a Radeon HD2600, but only video output after linux boot | ||||||
PCI Express x32 add-on cards | N/A | |||||||
HTX add-on cards | N/A | |||||||
Legacy / Super I/O | ||||||||
Floppy | N/A | |||||||
Serial port 1 (COM1) | OK | |||||||
Serial port 2 (COM2) | N/A | |||||||
Parallel port | N/A | |||||||
PS/2 keyboard | WIP | keyboard works under seabios and grub, but not under linux | ||||||
PS/2 mouse | Untested | simultaneous use of PS/2 keyboard and mouse with a Y-cable would require a small hardware mod (2 additional 0 ohms resistors) | ||||||
Game port | N/A | |||||||
Infrared | ? | |||||||
PC speaker | ? | |||||||
DiskOnChip | N/A | |||||||
Input | ||||||||
Trackpoint | N/A | |||||||
Touchpad | N/A | |||||||
Fn Hotkeys | N/A | |||||||
Fingerprint Reader | N/A | |||||||
Laptop | ||||||||
Docking VGA | N/A | |||||||
Docking LAN | N/A | |||||||
Docking USB | N/A | |||||||
Docking Audio | N/A | |||||||
Docking Displayport | N/A | |||||||
Thinklight | N/A | |||||||
Webcam | N/A | |||||||
Miscellaneous | ||||||||
Sensors / fan control | WIP | The CPU temperature seems to be displayed properly by lm-sensors. Fan control is not implemented. | ||||||
Hardware watchdog | Unknown | |||||||
SMBus | Unknown | |||||||
CAN bus | N/A | |||||||
CPU frequency scaling | OK | The ondemand governor works by default. | ||||||
Other powersaving features | OK | By default the CPU fan rotates at maximum speed. See the fancontrol attachment below on how to get it adjust automatically depending on CPU temperature. | ||||||
ACPI | ? | |||||||
Reboot | OK | |||||||
Poweroff | OK | |||||||
Suspend | NO | The machine suspends but it fails to resume from suspend. | ||||||
Nonstandard LEDs | N/A | |||||||
High precision event timers (HPET) | Unknown | |||||||
Random number generator (RNG) | ? | |||||||
Wake on modem ring | Untested | |||||||
Wake on LAN | Untested | |||||||
Wake on keyboard | Untested | |||||||
Wake on mouse | Untested | |||||||
TPM | Unknown | |||||||
Flashrom | OK |
Original BIOS information gathering
Dumps of information gathered by various commands while running the proprietary BIOS are available here: File:ASRock E350M1 info dump.tar.bz2
Hardware
The ROM chip is not soldered to the board but socketed. You can buy replacement (exact ROM chip for E350M1 or empty ones). See http://flashrom.org/Technology#DIP8:_Dual_In-line_Package.2C_8_pins and http://www.bios-chip24.com/Asrock-E350M1/en.
GPP PCIe ports on the FCH:
- port 0: mini PCIe slot
- port 1: ethernet chip
- port 2: UBS3 chip
- port 3: unconnected
GPP CLK ports on the FCH:
- port 0: mini PCIe slot
- port 1: ethernet chip
- port 2: UBS3 chip
- port 3: unconnected
- port 4: unconnected
- port 5: unconnected
- port 6: unconnected
- port 7: unconnected
- port 8: unconnected
GPP GFX SLT clock:
- PCIe card
PERST# for ethernet chip and mini PCIe card are connected to RSTOUT1# pin of the NCT5572D.
The SLP_S3# and SLP_S5# outputs of the FCH are connected to the corresponding inputs of the SIO.
Incomplete list of the connections to the SuperIO-chip
Temperature and fan control
Fan control is currently unimplemented in coreboot. Still it can be done in GNU/Linux.
Note that the mainboard manual states that only the CPU_FAN1 connector supports fan control.
Fancontrol configuration file for adjusting the CPU fan speed dynamically: File:Fancontrol.gz
/etc/fancontrol for trisquel
# Configuration file generated by pwmconfig, changes will be lost INTERVAL=10 DEVPATH=hwmon0=devices/pci0000:00/0000:00:18.3 hwmon1=devices/platform/w83627ehf.656 DEVNAME=hwmon0=k10temp hwmon1=nct6775 FCTEMPS=hwmon1/device/pwm2=hwmon0/device/temp1_input FCFANS= hwmon1/device/pwm2=hwmon1/device/fan2_input MINTEMP=hwmon1/device/pwm2=60 MAXTEMP=hwmon1/device/pwm2=65 MINSTART=hwmon1/device/pwm2=90 MINSTOP=hwmon1/device/pwm2=75 MINPWM=hwmon1/device/pwm2=0 MAXPWM=hwmon1/device/pwm2=255
/etc/fancontrol for GNU/Linux Debian 8
INTERVAL=10 DEVPATH=hwmon2=devices/pci0000:00/0000:00:18.3 hwmon1=devices/platform/w83627ehf.656 DEVNAME=hwmon2=k10temp hwmon1=nct6775 FCTEMPS=hwmon1/device/pwm2=hwmon2/device/temp1_input MINTEMP=hwmon1/device/pwm2=40 MAXTEMP=hwmon1/device/pwm2=65 MINSTART=hwmon1/device/pwm2=128 MINSTOP=hwmon1/device/pwm2=57 FCFANS=hwmon1/device/pwm2=hwmon1/device/fan2_input