Difference between revisions of "Board:hp/pavilion m6 1035dx"
m (→Old approach (deprected): Correctly spell deprec*a*ted)
(What are you talking about? The modified radeon is published.)
|Line 121:||Line 121:|
=== Status ===
=== Status ===
So far, there is a working driver to control transactions over the AUX channel. This is also used to read the EDID. There is also code to integrate this driver into linux, but
So far, there is a working driver to control transactions over the AUX channel. This is also used to read the EDID. There is also code to integrate this driver into linux, but needs more polishing before coming close to being upstreamable (see above).
Revision as of 22:31, 3 January 2015
- 1 Status
- 2 Recommended settings
- 3 Flashing
- 4 GPIO layout
- 5 Photos
- 6 General Purpose Events layout
- 7 EC headaches
- 8 TODO
- 9 Detective work
- 10 Native graphics init
Note that this information is for my personal records keeping, and is based on the latest local patches, some of which may not have been published yet.
- Succesfully booting to OS
- Keyboard and touchpad. (This touchpad is DIVINE!!!)
- Built-in Audio
- USB ports (USB 3.0 works with XHCI blob, the ports work with USB 2.0 devices without blob if XHCI controller is disabled)
- Wired and wireless networking. (Wired is a little wonky with some cables, works with others)
- Batterry status and notifications
- Batterry charging
- AC status LED next to power jack (white = charged, amber = charging)
- Power LED on power button (Not sure if it works as expected during suspend)
- Keyboard backlight and on/off control
- Hotkeys: Volume (Up/Down/Mute), Media (Prev/Play/Next), Keyboard backlight, WLAN toggle
- Caps Lock LED
- WLAN enabled/disabled LED
- Suspend/resume on lid closed/open
What doesn't work
- DVD drive. (has anyone tried HP's update for the DVD drive?)
- Power LED on the side (right above disk activity LED)
- Hotkeys: Brightess (Up/Down), Display Toggle. (We get SCIs from the EC)
- Mute LED (Note: doesn't work, even using OEM BIOS)
- Shutdown on critical battery level (We get a _Q25 SCI at 15% level, but that's also shared with insert/remove events)
- Setting Fn key mode to default on or default off. Right now it's default on.
The simplest way to get a working image is to start from the board-status entry, and use the same .config file.
Suspend/resume and display
This one is a doozie. Suspend/resume generally works, if the VGA bios was run at boot, but the display will not come back on after resume. However, if coreboot sets a VESA framebuffer, and keeps the framebuffer, resume with linux produces a working display again.
Devices -> [*] Run VGA Option ROMs Devices -> [*] Re-run VGA Option ROMs on S3 resume Display -> [*] Set framebuffer graphics resolution Display -> [*] Keep VESA framebuffer
A native VGA initialization option is under investigation.
Flashing works with flashrom, from either coreboot or the vendor BIOS.
$ flashrom -pinternal:laptop=force_I_want_a_brick,amd_imc_force=yes -w coreboot.rom
Expect this to be finicky, and be prepared to do an external flashif something fails.
This information should not be considered reliable in any way, shape or form
- GPIO57 - OUT - controls WLAN (rfkill pin on minipcie slot)
General Purpose Events layout
- GEVENT3 -> GPE3 - EC SCI
- GEVENT8 -> PCIE WAKE -> GPE24
- GEVENT23 -> EC SMI -> Configured as GEVENT23 SMI, not GPE23 SMI/SCI
- GEVENT22 -> GPE22 - EC LID
The MMIO dilemma
The EC RAM, which contains the batterry/AC etc information is normally accessed by read commands on the EC index I/O ports (0x62 and 0x66). The EC will also respond to LPC memory read/write cycles in the address range 0xff000000 + 0x1000. In order for this to work, the chipset must pass MMIO accesses in this range to the LPC bridge, which in turn, must decode them to the LPC bus.
This can't work if there is something else using that address range, so any system with 16MiB is out of the question. Luckily, the 1035dx uses a 4 MiB chip, so that's a non-issue. As a bonus, the LPC bridge can map a 4 KiB MMIO window on the LPC bus (or two, I can't remember).
The following script enables the needed MMIO window:
# iotools pci_write32 0 0x14 3 0x4c 0xff000000 # iotools pci_write32 0 0x14 3 0x48 0x00b0ff07
The EC RAM is at an offset of 0x800 from the MMIO base address. The current compal/ene932 ACPI implementation does not handle MMIO. This should be easily fixable with some preprocessor love.
Switching between APM/ACPI modes
Coreboot does it in the SMI handler on request form the OS. Doing that can also be accomplished in userspace by uberawesome blackmagic:
# iotools io_write8 0x66 0x59 && iotools io_write8 0x62 0xe9 # Put EC in APM mode # iotools io_write8 0x66 0x59 && iotools io_write8 0x62 0xe8 # Put EC in ACPI mode
- Check PCIe lane assignment (although PCIe devices seem to work fine)
Check grub2 payload(Run VGA option ROM and Keep VESA framebuffer -- works)
- Check AHCI port mask
- Examine possibility of native VGA init (funfunctor has some ideas)
- WLAN hotkey does not follow OS security model
- With vendor firmware, WLAN hotkey only works after logging in -- _Qxx handler uses device notifications rather than controlling the GPIOs directly
- Figure out how to make coreboot's ACPI behave the same way
Undocumented EC bits
Offsets relative to EC RAM.
- 0xb8.1 : Lid state (1 = closed, 0 = open)
Native graphics init
There is an effort by mrnuke, in conjunction with Edward from Altera Praxis, Ltd. to create native VGA init for ARUBA GPUs. Most of the work is hosted here:
So far, there is a working driver to control transactions over the AUX channel. This is also used to read the EDID. There is also code to integrate this driver into linux, but it needs a lot more polishing before coming close to being upstreamable (see above).
It is possible to run a replay of the VGA ROM in usermode, load the VGA ROM to memory, then load the radeon driver. This produces a working display without running the VGA ROM at boot. The advantage of this approach is that the realmode code in the VGA BIOS is never run.
The idea is to run the replay, then load a modified radeon driver. The radeon driver is hacked to replace individual atombios calls with native functions. For functions of interest, IO tracing is selectively enabled. The IO trace can then be compared to the trace left by the native function. Thus it's possible to RE one table at a time.
The integrated display is connected to a DP to LVDS converter, which is fed by the DisplayPort output of the APU. It seems the DP to LVDS chip is responsible for enabling the panel back-light. It is not yet known how this converter plays into enabling the backlight. There seems to be no need to poke the EC when enabling the display.
The VGA output seems to be connected to a DP to VGA converter, which is linked via a 4-lane DisplayPort link to the APU. It is believed the DP to VGA converter is part of the FCH.
The VGA ROM is an atombios which contains a realmode ATOM interpreter and atom command/data tables. Linux needs these tables to properly operate mode-switching and initializing the display controller. Linux does not run the realmode code. The ATOM tables can be dumped with AtomDis (TODO: add link to program).
Old approach (deprecated)
There has been some initial work in this regard:
Though this approach seems doomed. The radeon driver relies on atombios tables extensively, and the rest of the code is small shims to interface with the rest of linux. This approach can only produce those shims, whereas the bulk of the code is in the atom tables.