|
|
(6 intermediate revisions by the same user not shown) |
Line 5: |
Line 5: |
| == Known Issues == | | == Known Issues == |
| | | |
− | * pcie 06.0 bridge sometimes hangs probing the nic behind it. Linux reports a borked IRQ addr. They are likely connected? (Fix ACPI). | + | * pcie 06.0 bridge sometimes hangs probing the nic behind it. Linux reports a borked IRQ addr. They are likely connected? (Fix ACPI?). |
− | * superio not controlling fan - fix known, patch WIP!
| |
| * suspend/resume could do with some work to clean up nasty warnings.. (Fix ACPI). | | * suspend/resume could do with some work to clean up nasty warnings.. (Fix ACPI). |
| * some werid AGESA issue affects a number of boards | | * some werid AGESA issue affects a number of boards |
| | | |
− | === pcie 06.0 bridge hang issue === | + | == Overview == |
| | | |
− | The pcie 06.0 bridge hang issue is the primary remaining issue.
| + | === Hardware === |
| | | |
− | The Interrupt Mask Register (IMR) and Interrupt Service Register (ISR) are responsible for firing up different IRQs. The IMR bits line up with the ISR bits to work in sync. If an IMR bit is low, then the corresponding ISR bit with never fire an IRQ when the time comes for it to happen. The IMR is located at 0x3C and the ISR is located at 0x3E.
| + | * '''AMD Fusion G-series''' AMD Fusion G-T56N (1.65 GHz dual core) APU |
| + | * '''AMD A55E''' part of the chipset, AMD A55E (Hudson-E1) southbridge |
| + | * '''F71869AD''' Fintek F71869AD Super I/O |
| + | * '''RTL8111E''' Twin Realtek RTL8111E network controllers |
| + | * '''VT1705''' 6-Channel HD Audio (via VIA VT1705), AC97 AD/DA |
| | | |
| + | === Details === |
| | | |
− | Observe in the vendor bios pci configuration space dump attached below that, indx. 0x3C (IMR) = 0x0b and indx. 0x3E (ISR) = 0x10.
| + | The NF81-T56N-LF is a IPC form factor embedded board: |
| + | * AMD Fusion G-T56N (1.65 GHz dual core) APU |
| + | ** 2x SO-DIMM sockets for DDR3 800-1066 SDRAM (Fixed at 1.5V) |
| + | ** VGA and LVDS (via Analogix ANX3110) |
| + | * AMD A55E (Hudson-E1) southbridge |
| + | ** 6x USB 2.0/1.1 ports |
| + | ** 5x SATA3 6Gb/s, 1x mSATA socket |
| + | ** 6-Channel HD Audio (via VIA VT1705) |
| + | ** PCI and ISA (via ITE IT8888)?? |
| + | ** NEC uPD78F0532 microcontroller on I2C ("SEMA")?? |
| + | * 2x RJ45 GbE (via Realtek RTL8111E x2) |
| + | * Fintek F71869AD Super I/O |
| + | ** PS/2 KB/MS port |
| + | ** RS232 header (via Unisonic UTC 75232 RS232 driver/receiver) |
| + | ** GPIO header |
| + | ** CIR header |
| + | * 1x MXIC MX25L1606E (SO8, soldered) 16 Mbit SPI flash (BIOS) |
| | | |
− | IMR val. = 0000 1011 = INTB
| + | Note: MX25L1606E is 16Mbit, 8bits in a byte, so 2MB. Jetway '''''lies''''' |
− | ISR val. = 0000 1010
| + | claiming the SPI flash is 16MB. They also use red pen over the chip |
− | ====================
| + | so you wont see this deceit. |
− | &= 0000 1010
| |
− | ====================
| |
− | | |
− | root@archiso ~ # hexdump -C /sys/bus/pci/devices/0000:00:06.0/config
| |
− | 00000000 22 10 14 15 07 00 10 00 00 00 04 06 10 00 01 00 |"...............|
| |
− | 00000010 00 00 00 00 00 00 00 00 00 02 02 00 e1 e1 00 00 |................|
| |
− | 00000020 f0 ff 00 00 11 d0 11 d0 00 00 00 00 00 00 00 00 |................|
| |
− | 00000030 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 10 00 |....P...........|
| |
− | 00000040 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
| |
− | 00000050 01 58 03 c8 00 00 00 00 10 a0 42 01 20 80 00 00 |.X........B. ...|
| |
− | 00000060 00 08 00 00 11 0c 30 03 40 00 11 70 80 25 34 00 |......0.@..p.%4.|
| |
− | 00000070 00 00 48 01 00 00 01 00 00 00 00 00 1f 00 00 00 |..H.............|
| |
− | 00000080 06 00 00 00 00 00 00 00 21 00 00 00 00 00 00 00 |........!.......|
| |
− | 00000090 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
| |
− | 000000a0 05 b0 80 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
| |
− | 000000b0 0d b8 00 00 22 10 34 12 08 00 03 a8 00 00 00 00 |....".4.........|
| |
− | 000000c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
| |
− | *
| |
− | 000000e0 50 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 |P...............|
| |
− | 000000f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
| |
− | 00000100 0b 00 01 00 01 00 01 01 00 00 00 00 00 00 00 00 |................|
| |
− | 00000110 02 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
| |
− | 00000120 01 00 00 00 ff 00 00 80 00 00 00 00 01 00 00 00 |................|
| |
− | 00000130 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 |................|
| |
− | 00000140 03 00 01 00 01 00 00 00 00 87 0c 00 00 00 00 00 |................|
| |
− | 00000150 01 00 01 00 00 00 00 00 00 00 00 00 30 20 06 00 |............0 ..|
| |
− | 00000160 00 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 |..... ..........|
| |
− | 00000170 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
| |
− | *
| |
− | 00000190 0d 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
| |
− | 000001a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
| |
− | *
| |
− | 00001000
| |
| | | |
− | Investigate in board support:
| + | === Building a coreboot image === |
− | * acpi/routing.asl
| |
− | * mptable.c
| |
| | | |
− | === weird AGESA issue ===
| + | Make a fresh clone of Coreboot into a empty directory and run: |
| + | make crossgcc-i386 |
| + | Make a cup of tea.. Then run: |
| + | make menuconfig |
| + | and select Jetway/NF81-t56N-LF under "Mainboard -> Mainboard vendor/model" leaving |
| + | everything else as defaults. Then finally do, |
| + | make |
| | | |
− | The function call goes something like this; In
| + | To flash the board with '''flashrom''' run: |
− | mainboard/jetway/nf81-t56n-lf/agesawrapper.c
| + | flashrom -p ft2232_spi:type=2232H,port=A -c "MX25L1605A/MX25L1606E" -w build/coreboot.rom |
− | the function | + | ''assuming'' you have a SPI flasher setup. |
− | UINT32 agesawrapper_amdinitpost(VOID)
| |
− | calls
| |
− | status = AmdInitPost ((AMD_POST_PARAMS *)AmdParamStruct.NewStructPtr);
| |
− | this returns a error code of
| |
− | AGESA_WARNING = 0x4
| |
− | this triggers
| |
− | if(status != AGESA_SUCCESS) agesawrapper_amdreadeventlog();
| |
− | giving the resulting message:
| |
− | | |
− | EventLog: EventClass = 2, EventInfo = 8040100.
| |
− | ...
| |
− | | |
− | grep'ing we have that:
| |
− | AGESA.h:#define CPU_ERROR_HEAP_BUFFER_HANDLE_IS_NOT_PRESENT 0x08040100ul
| |
− | | |
− | However tracing the call back to where '''AGESA_WARNING''' is set goes back to:
| |
− | vendor/amd/agesa/f14/Proc/Mem/Main/mmflow.c | |
− | line '''290''' here:
| |
− | Retval = NBPtr[Die].MCTPtr->ErrCode;
| |
− | with '''Die=0'''.
| |
| | | |
| == Status == | | == Status == |
Line 99: |
Line 70: |
| |CPU_multiple_status = N/A | | |CPU_multiple_status = N/A |
| |CPU_multicore_status = N/A | | |CPU_multicore_status = N/A |
− | |CPU_virt_status = WIP | + | |CPU_virt_status = OK |
| | | |
| |RAM_EDO_status = N/A | | |RAM_EDO_status = N/A |
Line 160: |
Line 131: |
| |DiskOnChip_status = N/A | | |DiskOnChip_status = N/A |
| | | |
− | |Sensors_status = Pending | + | |Sensors_status = OK |
− | |Sensors_comments = See Gerrit 5500 | + | |Sensors_comments = |
| |Watchdog_status = Pending | | |Watchdog_status = Pending |
− | |Watchdog_comments = Need to look over Super I/O datasheet for this? | + | |Watchdog_comments = What needs to be done here?? |
| |SMBus_status = OK | | |SMBus_status = OK |
| |CAN_bus_status = N/A | | |CAN_bus_status = N/A |
Line 186: |
Line 157: |
| }} | | }} |
| | | |
− | == Hardware == | + | == Issue Analysis == |
| | | |
− | === Overview === | + | === pcie 06.0 bridge hang issue === |
| | | |
− | * '''AMD Fusion G-series''' AMD Fusion G-T56N (1.65 GHz dual core) APU
| + | The pcie 06.0 bridge hang issue is the primary remaining issue. |
− | * '''AMD A55E''' part of the chipset, AMD A55E (Hudson-E1) southbridge
| |
− | * '''F71869AD''' Fintek F71869AD Super I/O
| |
− | * '''RTL8111E''' Twin Realtek RTL8111E network controllers
| |
− | * '''VT1705''' 6-Channel HD Audio (via VIA VT1705), AC97 AD/DA
| |
| | | |
− | === Details ===
| + | The Interrupt Mask Register (IMR) and Interrupt Service Register (ISR) are responsible for firing up different IRQs. The IMR bits line up with the ISR bits to work in sync. If an IMR bit is low, then the corresponding ISR bit with never fire an IRQ when the time comes for it to happen. The IMR is located at 0x3C and the ISR is located at 0x3E. |
| | | |
− | The NF81-T56N-LF is a IPC form factor embedded board:
| |
− | * AMD Fusion G-T56N (1.65 GHz dual core) APU
| |
− | ** 2x SO-DIMM sockets for DDR3 800-1066 SDRAM (Fixed at 1.5V)
| |
− | ** VGA and LVDS (via Analogix ANX3110)
| |
− | * AMD A55E (Hudson-E1) southbridge
| |
− | ** 6x USB 2.0/1.1 ports
| |
− | ** 5x SATA3 6Gb/s, 1x mSATA socket
| |
− | ** 6-Channel HD Audio (via VIA VT1705)
| |
− | ** PCI and ISA (via ITE IT8888)??
| |
− | ** NEC uPD78F0532 microcontroller on I2C ("SEMA")??
| |
− | * 2x RJ45 GbE (via Realtek RTL8111E x2)
| |
− | * Fintek F71869AD Super I/O
| |
− | ** PS/2 KB/MS port
| |
− | ** RS232 header (via Unisonic UTC 75232 RS232 driver/receiver)
| |
− | ** GPIO header
| |
− | ** CIR header
| |
− | * 1x MXIC MX25L1606E (SO8, soldered) 16 Mbit SPI flash (BIOS)
| |
| | | |
− | Note: MX25L1606E is 16Mbit, 8bits in a byte, so 2MB. Jetway '''''lies'''''
| + | Observe in the vendor bios pci configuration space dump attached below that, indx. 0x3C (IMR) = 0x0b and indx. 0x3E (ISR) = 0x10. |
− | claiming the SPI flash is 16MB. They also use red pen over the chip
| |
− | so you wont see this deceit.
| |
| | | |
− | == Building a coreboot image == | + | IMR val. = 0000 1011 = INTB |
| + | ISR val. = 0000 1010 |
| + | ==================== |
| + | &= 0000 1010 |
| + | ==================== |
| | | |
− | Make a fresh clone of Coreboot into a empty directory and run:
| + | root@archiso ~ # hexdump -C /sys/bus/pci/devices/0000:00:06.0/config |
− | make crossgcc-i386 | + | 00000000 22 10 14 15 07 00 10 00 00 00 04 06 10 00 01 00 |"...............| |
− | Make a cup of tea.. Then run:
| + | 00000010 00 00 00 00 00 00 00 00 00 02 02 00 e1 e1 00 00 |................| |
− | make menuconfig | + | 00000020 f0 ff 00 00 11 d0 11 d0 00 00 00 00 00 00 00 00 |................| |
− | and select Jetway/NF81-t56N-LF under "Mainboard -> Mainboard vendor/model" leaving
| + | 00000030 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 10 00 |....P...........| |
− | everything else as defaults. Then finally do,
| + | 00000040 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| |
− | make | + | 00000050 01 58 03 c8 00 00 00 00 10 a0 42 01 20 80 00 00 |.X........B. ...| |
| + | 00000060 00 08 00 00 11 0c 30 03 40 00 11 70 80 25 34 00 |......0.@..p.%4.| |
| + | 00000070 00 00 48 01 00 00 01 00 00 00 00 00 1f 00 00 00 |..H.............| |
| + | 00000080 06 00 00 00 00 00 00 00 21 00 00 00 00 00 00 00 |........!.......| |
| + | 00000090 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| |
| + | 000000a0 05 b0 80 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| |
| + | 000000b0 0d b8 00 00 22 10 34 12 08 00 03 a8 00 00 00 00 |....".4.........| |
| + | 000000c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| |
| + | * |
| + | 000000e0 50 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 |P...............| |
| + | 000000f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| |
| + | 00000100 0b 00 01 00 01 00 01 01 00 00 00 00 00 00 00 00 |................| |
| + | 00000110 02 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| |
| + | 00000120 01 00 00 00 ff 00 00 80 00 00 00 00 01 00 00 00 |................| |
| + | 00000130 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 |................| |
| + | 00000140 03 00 01 00 01 00 00 00 00 87 0c 00 00 00 00 00 |................| |
| + | 00000150 01 00 01 00 00 00 00 00 00 00 00 00 30 20 06 00 |............0 ..| |
| + | 00000160 00 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 |..... ..........| |
| + | 00000170 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| |
| + | * |
| + | 00000190 0d 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| |
| + | 000001a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| |
| + | * |
| + | 00001000 |
| | | |
− | To flash the board with '''flashrom''' run:
| + | Investigate in board support: |
− | flashrom -p ft2232_spi:type=2232H,port=A -c "MX25L1605A/MX25L1606E" -w build/coreboot.rom | + | * acpi/routing.asl |
− | ''assuming'' you have a SPI flasher setup.
| + | * mptable.c |
| | | |
− | == Various logs == | + | === weird AGESA issue === |
| | | |
− | === lspci -tvnn ===
| + | The function call goes something like this; In |
| + | mainboard/jetway/nf81-t56n-lf/agesawrapper.c |
| + | the function |
| + | UINT32 agesawrapper_amdinitpost(VOID) |
| + | calls |
| + | status = AmdInitPost ((AMD_POST_PARAMS *)AmdParamStruct.NewStructPtr); |
| + | this returns a error code of |
| + | AGESA_WARNING = 0x4 |
| + | this triggers |
| + | if(status != AGESA_SUCCESS) agesawrapper_amdreadeventlog(); |
| + | giving the resulting message: |
| | | |
− | 00:00.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 14h Processor Root Complex [1022:1510] | + | EventLog: EventClass = 2, EventInfo = 8040100. |
− | Subsystem: Advanced Micro Devices, Inc. [AMD] Family 14h Processor Root Complex [1022:1510]
| + | ... |
− | Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32
| |
− |
| |
− | 00:01.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Wrestler [Radeon HD 6320] [1002:9806] (prog-if 00 [VGA controller])
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD] Device [1022:1511]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
| |
− | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 0, Cache Line Size: 64 bytes
| |
− | Interrupt: pin A routed to IRQ 42
| |
− | Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
| |
− | Region 1: I/O ports at f000 [size=256]
| |
− | Region 2: Memory at feb00000 (32-bit, non-prefetchable) [size=256K]
| |
− | Expansion ROM at <unassigned> [disabled]
| |
− | Capabilities: [50] Power Management version 3
| |
− | Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| |
− | Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
| |
− | Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI 00
| |
− | DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
| |
− | ExtTag+ RBE+ FLReset-
| |
− | DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
| |
− | RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
| |
− | MaxPayload 128 bytes, MaxReadReq 128 bytes
| |
− | DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
| |
− | LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
| |
− | ClockPM- Surprise- LLActRep- BwNot-
| |
− | LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
| |
− | ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
| |
− | LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
| |
− | DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported
| |
− | DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
| |
− | LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
| |
− | Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
| |
− | Compliance De-emphasis: -6dB
| |
− | LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
| |
− | EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
| |
− | Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
| |
− | Address: 00000000fee0300c Data: 41a1
| |
− | Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
| |
− | Kernel driver in use: radeon
| |
− |
| |
− | 00:01.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Wrestler HDMI Audio [1002:1314]
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD] Device [1022:1511]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
| |
− | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 0, Cache Line Size: 64 bytes
| |
− | Interrupt: pin B routed to IRQ 43
| |
− | Region 0: Memory at feb44000 (32-bit, non-prefetchable) [size=16K]
| |
− | Capabilities: [50] Power Management version 3
| |
− | Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| |
− | Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
| |
− | Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI 00
| |
− | DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
| |
− | ExtTag+ RBE+ FLReset-
| |
− | DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
| |
− | RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
| |
− | MaxPayload 128 bytes, MaxReadReq 128 bytes
| |
− | DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
| |
− | LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
| |
− | ClockPM- Surprise- LLActRep- BwNot-
| |
− | LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
| |
− | ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
| |
− | LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
| |
− | DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported
| |
− | DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
| |
− | LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
| |
− | Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
| |
− | Compliance De-emphasis: -6dB
| |
− | LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
| |
− | EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
| |
− | Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
| |
− | Address: 00000000fee0300c Data: 41b1
| |
− | Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
| |
− | Kernel driver in use: snd_hda_intel
| |
− |
| |
− | 00:04.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Family 14h Processor Root Port [1022:1512] (prog-if 00 [Normal decode])
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 0, Cache Line Size: 64 bytes
| |
− | Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
| |
− | I/O behind bridge: 00001000-00001fff
| |
− | Memory behind bridge: d0200000-d03fffff
| |
− | Prefetchable memory behind bridge: 00000000d0400000-00000000d05fffff
| |
− | Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
| |
− | BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
| |
− | PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
| |
− | Capabilities: [50] Power Management version 3
| |
− | Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
| |
− | Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
| |
− | Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
| |
− | DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
| |
− | ExtTag+ RBE+ FLReset-
| |
− | DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
| |
− | RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
| |
− | MaxPayload 128 bytes, MaxReadReq 128 bytes
| |
− | DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
| |
− | LnkCap: Port #247, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
| |
− | ClockPM- Surprise- LLActRep+ BwNot+
| |
− | LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
| |
− | ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
| |
− | LnkSta: Speed unknown, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
| |
− | SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise-
| |
− | Slot #4, PowerLimit 75.000W; Interlock- NoCompl+
| |
− | SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
| |
− | Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
| |
− | SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
| |
− | Changed: MRL- PresDet- LinkState-
| |
− | RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
| |
− | RootCap: CRSVisible-
| |
− | RootSta: PME ReqID 0000, PMEStatus- PMEPending-
| |
− | DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
| |
− | DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
| |
− | LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis+
| |
− | Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
| |
− | Compliance De-emphasis: -6dB
| |
− | LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
| |
− | EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
| |
− | Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
| |
− | Address: 0000000000000000 Data: 0000
| |
− | Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD] Device [1022:1234]
| |
− | Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
| |
− | Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
| |
− | Kernel driver in use: pcieport
| |
− |
| |
− | 00:06.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Family 14h Processor Root Port [1022:1514] (prog-if 00 [Normal decode])
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 0, Cache Line Size: 64 bytes
| |
− | Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
| |
− | I/O behind bridge: 0000e000-0000efff
| |
− | Memory behind bridge: fff00000-000fffff
| |
− | Prefetchable memory behind bridge: 00000000d0100000-00000000d01fffff
| |
− | Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
| |
− | BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
| |
− | PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
| |
− | Capabilities: [50] Power Management version 3
| |
− | Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
| |
− | Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
| |
− | Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
| |
− | DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
| |
− | ExtTag+ RBE+ FLReset-
| |
− | DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
| |
− | RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
| |
− | MaxPayload 128 bytes, MaxReadReq 128 bytes
| |
− | DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
| |
− | LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
| |
− | ClockPM- Surprise- LLActRep+ BwNot+
| |
− | LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
| |
− | ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
| |
− | LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
| |
− | SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
| |
− | Slot #6, PowerLimit 75.000W; Interlock- NoCompl+
| |
− | SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
| |
− | Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
| |
− | SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
| |
− | Changed: MRL- PresDet+ LinkState+
| |
− | RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
| |
− | RootCap: CRSVisible-
| |
− | RootSta: PME ReqID 0000, PMEStatus- PMEPending-
| |
− | DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
| |
− | DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
| |
− | LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis+
| |
− | Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
| |
− | Compliance De-emphasis: -6dB
| |
− | LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
| |
− | EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
| |
− | Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
| |
− | Address: 0000000000000000 Data: 0000
| |
− | Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD] Device [1022:1234]
| |
− | Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
| |
− | Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
| |
− | Kernel driver in use: pcieport
| |
− |
| |
− | 00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] (rev 40) (prog-if 01 [AHCI 1.0])
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device [1002:4393]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32
| |
− | Interrupt: pin A routed to IRQ 19
| |
− | Region 0: I/O ports at f190 [size=8]
| |
− | Region 1: I/O ports at f180 [size=4]
| |
− | Region 2: I/O ports at f170 [size=8]
| |
− | Region 3: I/O ports at f160 [size=4]
| |
− | Region 4: I/O ports at f150 [size=16]
| |
− | Region 5: Memory at feb4f000 (32-bit, non-prefetchable) [size=1K]
| |
− | Capabilities: [70] SATA HBA v1.0 InCfgSpace
| |
− | Capabilities: [a4] PCI Advanced Features
| |
− | AFCap: TP+ FLR+
| |
− | AFCtrl: FLR-
| |
− | AFStatus: TP-
| |
− | Kernel driver in use: ahci
| |
− |
| |
− | 00:12.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32, Cache Line Size: 64 bytes
| |
− | Interrupt: pin A routed to IRQ 18
| |
− | Region 0: Memory at feb4e000 (32-bit, non-prefetchable) [size=4K]
| |
− | Kernel driver in use: ohci_hcd
| |
− |
| |
− | 00:12.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32, Cache Line Size: 64 bytes
| |
− | Interrupt: pin B routed to IRQ 17
| |
− | Region 0: Memory at feb4d000 (32-bit, non-prefetchable) [size=256]
| |
− | Capabilities: [c0] Power Management version 2
| |
− | Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
| |
− | Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
| |
− | Bridge: PM- B3+
| |
− | Capabilities: [e4] Debug port: BAR=1 offset=00e0
| |
− | Kernel driver in use: ehci-pci
| |
− |
| |
− | 00:13.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32, Cache Line Size: 64 bytes
| |
− | Interrupt: pin A routed to IRQ 18
| |
− | Region 0: Memory at feb4c000 (32-bit, non-prefetchable) [size=4K]
| |
− | Kernel driver in use: ohci_hcd
| |
− |
| |
− | 00:13.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32, Cache Line Size: 64 bytes
| |
− | Interrupt: pin B routed to IRQ 17
| |
− | Region 0: Memory at feb4b000 (32-bit, non-prefetchable) [size=256]
| |
− | Capabilities: [c0] Power Management version 2
| |
− | Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
| |
− | Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
| |
− | Bridge: PM- B3+
| |
− | Capabilities: [e4] Debug port: BAR=1 offset=00e0
| |
− | Kernel driver in use: ehci-pci
| |
− |
| |
− | 00:14.0 SMBus [0c05]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller [1002:4385] (rev 42)
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller [1002:4385]
| |
− | Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
| |
− | Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Kernel driver in use: piix4_smbus
| |
− |
| |
− | 00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] (rev 40) (prog-if 8a [Master SecP PriP])
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32
| |
− | Interrupt: pin B routed to IRQ 17
| |
− | Region 0: I/O ports at 01f0 [size=8]
| |
− | Region 1: I/O ports at 03f4
| |
− | Region 2: I/O ports at 0170 [size=8]
| |
− | Region 3: I/O ports at 0374
| |
− | Region 4: I/O ports at f100 [size=16]
| |
− | Kernel driver in use: pata_atiixp
| |
− |
| |
− | 00:14.2 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) [1002:4383] (rev 40)
| |
− | Subsystem: Jetway Information Co., Ltd. Device [16f3:1705]
| |
− | Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32, Cache Line Size: 64 bytes
| |
− | Interrupt: pin A routed to IRQ 16
| |
− | Region 0: Memory at feb40000 (64-bit, non-prefetchable) [size=16K]
| |
− | Capabilities: [50] Power Management version 2
| |
− | Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
| |
− | Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
| |
− | Kernel driver in use: snd_hda_intel
| |
− |
| |
− | 00:14.3 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] (rev 40)
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 0
| |
− | | |
− | 00:14.4 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge [1002:4384] (rev 40) (prog-if 01 [Subtractive decode])
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 64
| |
− | Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
| |
− | I/O behind bridge: 0000f000-00000fff
| |
− | Memory behind bridge: fff00000-000fffff
| |
− | Prefetchable memory behind bridge: fff00000-000fffff
| |
− | Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
| |
− | BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
| |
− | PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
| |
− |
| |
− | 00:14.5 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32, Cache Line Size: 64 bytes
| |
− | Interrupt: pin C routed to IRQ 18
| |
− | Region 0: Memory at feb4a000 (32-bit, non-prefetchable) [size=4K]
| |
− | Kernel driver in use: ohci_hcd
| |
− |
| |
− | 00:15.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) [1002:43a0] (prog-if 00 [Normal decode])
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 0, Cache Line Size: 64 bytes
| |
− | Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
| |
− | I/O behind bridge: 0000d000-0000dfff
| |
− | Memory behind bridge: fff00000-000fffff
| |
− | Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff
| |
− | Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
| |
− | BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
| |
− | PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
| |
− | Capabilities: [50] Power Management version 3
| |
− | Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| |
− | Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
| |
− | Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
| |
− | DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
| |
− | ExtTag+ RBE+ FLReset-
| |
− | DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
| |
− | RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
| |
− | MaxPayload 128 bytes, MaxReadReq 128 bytes
| |
− | DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
| |
− | LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
| |
− | ClockPM- Surprise- LLActRep+ BwNot+
| |
− | LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
| |
− | ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
| |
− | LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
| |
− | RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
| |
− | RootCap: CRSVisible-
| |
− | RootSta: PME ReqID 0000, PMEStatus- PMEPending-
| |
− | DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
| |
− | DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
| |
− | LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
| |
− | Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
| |
− | Compliance De-emphasis: -6dB
| |
− | LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
| |
− | EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
| |
− | Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
| |
− | Address: 0000000000000000 Data: 0000
| |
− | Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device [1002:0000]
| |
− | Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
| |
− | Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
| |
− | Kernel driver in use: pcieport
| |
− |
| |
− | 00:16.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32, Cache Line Size: 64 bytes
| |
− | Interrupt: pin A routed to IRQ 18
| |
− | Region 0: Memory at feb49000 (32-bit, non-prefetchable) [size=4K]
| |
− | Kernel driver in use: ohci_hcd
| |
− |
| |
− | 00:16.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
| |
− | Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 32, Cache Line Size: 64 bytes
| |
− | Interrupt: pin B routed to IRQ 17
| |
− | Region 0: Memory at feb48000 (32-bit, non-prefetchable) [size=256]
| |
− | Capabilities: [c0] Power Management version 2
| |
− | Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
| |
− | Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
| |
− | Bridge: PM- B3+
| |
− | Capabilities: [e4] Debug port: BAR=1 offset=00e0
| |
− | Kernel driver in use: ehci-pci
| |
− |
| |
− | 00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 0 [1022:1700] (rev 43)
| |
− | Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− |
| |
− | 00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 1 [1022:1701]
| |
− | Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− |
| |
− | 00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 2 [1022:1702]
| |
− | Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− |
| |
− | 00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 3 [1022:1703]
| |
− | Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Capabilities: [f0] Secure device <?>
| |
− | Kernel driver in use: k10temp
| |
− |
| |
− | 00:18.4 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 4 [1022:1704]
| |
− | Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− |
| |
− | 00:18.5 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 6 [1022:1718]
| |
− | Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− |
| |
− | 00:18.6 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 5 [1022:1716]
| |
− | Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− |
| |
− | 00:18.7 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 7 [1022:1719]
| |
− | Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
| |
− | Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− |
| |
− | 02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
| |
− | Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller [10ec:8168]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
| |
− | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 0, Cache Line Size: 64 bytes
| |
− | Interrupt: pin A routed to IRQ 40
| |
− | Region 0: I/O ports at e000 [size=256]
| |
− | Region 2: Memory at d0104000 (64-bit, prefetchable) [size=4K]
| |
− | Region 4: Memory at d0100000 (64-bit, prefetchable) [size=16K]
| |
− | Capabilities: [40] Power Management version 3
| |
− | Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
| |
− | Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
| |
− | Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
| |
− | Address: 00000000fee0300c Data: 4171
| |
− | Capabilities: [70] Express (v2) Endpoint, MSI 01
| |
− | DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
| |
− | ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
| |
− | DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
| |
− | RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
| |
− | MaxPayload 128 bytes, MaxReadReq 4096 bytes
| |
− | DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
| |
− | LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
| |
− | ClockPM+ Surprise- LLActRep- BwNot-
| |
− | LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
| |
− | ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
| |
− | LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
| |
− | DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
| |
− | DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
| |
− | LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
| |
− | Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
| |
− | Compliance De-emphasis: -6dB
| |
− | LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
| |
− | EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
| |
− | Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
| |
− | Vector table: BAR=4 offset=00000000
| |
− | PBA: BAR=4 offset=00000800
| |
− | Capabilities: [d0] Vital Product Data
| |
− | Unknown small resource type 00, will not decode more.
| |
− | Capabilities: [100 v1] Advanced Error Reporting
| |
− | UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
| |
− | UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
| |
− | UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
| |
− | CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
| |
− | CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
| |
− | AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
| |
− | Capabilities: [140 v1] Virtual Channel
| |
− | Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
| |
− | Arb: Fixed- WRR32- WRR64- WRR128-
| |
− | Ctrl: ArbSelect=Fixed
| |
− | Status: InProgress-
| |
− | VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
| |
− | Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
| |
− | Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
| |
− | Status: NegoPending- InProgress-
| |
− | Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
| |
− | Kernel driver in use: r8169
| |
− |
| |
− | 04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
| |
− | Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller [10ec:8168]
| |
− | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
| |
− | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
| |
− | Latency: 0, Cache Line Size: 64 bytes
| |
− | Interrupt: pin A routed to IRQ 41
| |
− | Region 0: I/O ports at d000 [size=256]
| |
− | Region 2: Memory at d0004000 (64-bit, prefetchable) [size=4K]
| |
− | Region 4: Memory at d0000000 (64-bit, prefetchable) [size=16K]
| |
− | Capabilities: [40] Power Management version 3
| |
− | Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
| |
− | Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
| |
− | Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
| |
− | Address: 00000000fee0300c Data: 4181
| |
− | Capabilities: [70] Express (v2) Endpoint, MSI 01
| |
− | DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
| |
− | ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
| |
− | DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
| |
− | RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
| |
− | MaxPayload 128 bytes, MaxReadReq 4096 bytes
| |
− | DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
| |
− | LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
| |
− | ClockPM+ Surprise- LLActRep- BwNot-
| |
− | LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
| |
− | ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
| |
− | LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
| |
− | DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
| |
− | DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
| |
− | LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
| |
− | Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
| |
− | Compliance De-emphasis: -6dB
| |
− | LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
| |
− | EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
| |
− | Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
| |
− | Vector table: BAR=4 offset=00000000
| |
− | PBA: BAR=4 offset=00000800
| |
− | Capabilities: [d0] Vital Product Data
| |
− | Unknown small resource type 00, will not decode more.
| |
− | Capabilities: [100 v1] Advanced Error Reporting
| |
− | UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
| |
− | UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
| |
− | UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
| |
− | CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
| |
− | CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
| |
− | AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
| |
− | Capabilities: [140 v1] Virtual Channel
| |
− | Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
| |
− | Arb: Fixed- WRR32- WRR64- WRR128-
| |
− | Ctrl: ArbSelect=Fixed
| |
− | Status: InProgress-
| |
− | VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
| |
− | Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
| |
− | Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
| |
− | Status: NegoPending- InProgress-
| |
− | Capabilities: [160 v1] Device Serial Number 02-00-00-00-68-4c-e0-00
| |
− | Kernel driver in use: r8169
| |
| | | |
| + | grep'ing we have that: |
| + | AGESA.h:#define CPU_ERROR_HEAP_BUFFER_HANDLE_IS_NOT_PRESENT 0x08040100ul |
| | | |
− | === SuperI/O tool log ===
| + | However tracing the call back to where '''AGESA_WARNING''' is set goes back to: |
− | | + | vendor/amd/agesa/f14/Proc/Mem/Main/mmflow.c |
− | superiotool r4.0-5364-gb16690d | + | line '''290''' here: |
− | Found Fintek F71869AD (vid=0x3419, id=0x0710) at 0x2e
| + | Retval = NBPtr[Die].MCTPtr->ErrCode; |
− | Register dump:
| + | with '''Die=0'''. |
− | idx 02 07 20 21 25 26 27 28 29 2a 2b 2c 2d
| |
− | val 00 0b 10 07 00 00 a1 01 6f 24 00 60 2f
| |
− | def 00 00 08 14 00 00 MM 38 6f 07 0f 00 28
| |
− | LDN 0x00 (Floppy)
| |
− | idx 30 60 61 70 74 f0 f2 f4
| |
− | val 00 03 f0 06 02 0e ff 00
| |
− | def 01 03 f0 06 02 0e 03 00
| |
− | LDN 0x01 (COM1)
| |
− | idx 30 60 61 70 f0
| |
− | val 01 03 f8 04 00
| |
− | def 01 03 f8 04 00
| |
− | LDN 0x02 (COM2)
| |
− | idx 30 60 61 70 f0 f1
| |
− | val 00 02 f8 03 00 44
| |
− | def 01 02 f8 03 00 04
| |
− | LDN 0x03 (Parallel port)
| |
− | idx 30 60 61 70 74 f0
| |
− | val 00 03 78 07 03 42
| |
− | def 01 03 78 07 03 42
| |
− | LDN 0x04 (Hardware monitor)
| |
− | idx 30 60 61 70
| |
− | val 01 02 25 00
| |
− | def 01 02 95 00
| |
− | LDN 0x05 (Keyboard)
| |
− | idx 30 60 61 70 72 f0 fe ff
| |
− | val 01 00 60 01 0c ff 81 29
| |
− | def 01 00 60 01 0c 83 81 29
| |
− | LDN 0x06 (GPIO)
| |
− | idx 30 60 61 70 f0 f1 f2 f3 e0 e1 e2 e3 e4 e5 e6 d0 d1 d2 d3 c0 c1 c2 b0 b1 b2 b3 a0 a1 a2 a3 90 91 92 93
| |
− | val 01 0a 00 00 00 3f 00 00 20 df 91 00 00 00 05 00 ff a7 00 ff 00 00 00 ff 73 00 00 1f 00 ff 00 ff 00 00
| |
− | def 00 00 00 00 00 3f NA 00 00 ff NA 00 00 00 00 00 ff NA 00 00 ff NA 00 0f NA 00 00 1f NA 00 00 3f NA 00
| |
− | LDN 0x07 (BSEL)
| |
− | idx 30 60 61 f0 f2 f3 f4 f5 f6 f7
| |
− | val 00 00 00 01 ff ff ff 12 0a 01
| |
− | def 00 00 00 01 00 00 NA 00 0a 00
| |
− | LDN 0x0a (PME, ACPI)
| |
− | idx 30 f0 f1 f2 f3 f4 f5 f6 f7 f8 f9 fe ff
| |
− | val 00 00 6a 00 00 46 1c 1f 86 00 00 00 00
| |
− | def 00 00 00 NA NA 06 1c 1f 86 00 00 00 00
| |
| | | |
− | === Coreboot S3 resume log === | + | === Coreboot S3 suspend/resume === |
| | | |
| S3 Suspend/Resume works by running: | | S3 Suspend/Resume works by running: |
This page is a work in progress. ACPI is still being worked on, however due to the nature of ACPI it may take some time to get this right.
Note: MX25L1606E is 16Mbit, 8bits in a byte, so 2MB. Jetway lies
claiming the SPI flash is 16MB. They also use red pen over the chip
so you wont see this deceit.
Make a cup of tea.. Then run:
and select Jetway/NF81-t56N-LF under "Mainboard -> Mainboard vendor/model" leaving
everything else as defaults. Then finally do,
The pcie 06.0 bridge hang issue is the primary remaining issue.
The Interrupt Mask Register (IMR) and Interrupt Service Register (ISR) are responsible for firing up different IRQs. The IMR bits line up with the ISR bits to work in sync. If an IMR bit is low, then the corresponding ISR bit with never fire an IRQ when the time comes for it to happen. The IMR is located at 0x3C and the ISR is located at 0x3E.