Difference between revisions of "Board:kontron/986lcd-m"
From coreboot
m (More notes and updates.) |
m |
||
Line 32: | Line 32: | ||
|USB_status = OK | |USB_status = OK | ||
|USB_comments = Tested: USB thumb drive in all 4 backpanel USB ports. The onboard USB pin headers are untested, but should also work. | |USB_comments = Tested: USB thumb drive in all 4 backpanel USB ports. The onboard USB pin headers are untested, but should also work. | ||
− | |Onboard_VGA_status = | + | |Onboard_VGA_status = OK |
− | |Onboard_ethernet_status = ? | + | |Onboard_VGA_comments = You need to prepend the VGA blob from the proprietary BIOS for this to work. |
− | |Onboard_audio_status = | + | |Onboard_ethernet_status = WIP |
− | |Onboard_modem_status = | + | |Onboard_ethernet_comments = The '''eth1''' interface (in this case) works fine, but so far '''ifconfig -a''' only shows one of the three NICs (?) |
+ | |Onboard_audio_status = WIP | ||
+ | |Onboard_audio_comments = Doesn't seem to work, yet. | ||
+ | |Onboard_modem_status = N/A | ||
|Onboard_firewire_status = ? | |Onboard_firewire_status = ? | ||
|Smartcard_status = N/A | |Smartcard_status = N/A | ||
Line 78: | Line 81: | ||
|Poweroff_status = ? | |Poweroff_status = ? | ||
|Poweroff_comments = Needs ACPI, thus won't work if you use '''acpi=off''' on the Linux kernel command line. | |Poweroff_comments = Needs ACPI, thus won't work if you use '''acpi=off''' on the Linux kernel command line. | ||
− | |LEDs_status = | + | |LEDs_status = N/A |
|HPET_status = OK | |HPET_status = OK | ||
|HPET_comments = The HPET is detected by Linux ('''hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0''') and '''powertop''' output suggests that it works ok. | |HPET_comments = The HPET is detected by Linux ('''hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0''') and '''powertop''' output suggests that it works ok. | ||
Line 109: | Line 112: | ||
* Currently you have to use '''acpi=off''' on the kernel command line to make IDE work. | * Currently you have to use '''acpi=off''' on the kernel command line to make IDE work. | ||
* If you experience kernel crashes try to blacklist the '''agpgart''' and '''intel_agp''' kernel modules. | * If you experience kernel crashes try to blacklist the '''agpgart''' and '''intel_agp''' kernel modules. | ||
+ | * TODO: Add notes for proper (onboard) VGA setup. | ||
{{PD-self}} | {{PD-self}} |
Revision as of 21:17, 18 December 2008
This page describes how to use coreboot on the Kontron 986LCD-M/mITX mainboard. It is maintained by Uwe Hermann.
Status
Device/functionality | Status | Comments | ||||||
---|---|---|---|---|---|---|---|---|
CPU | ||||||||
CPU works | OK | Intel(R) Core(TM)2 CPU T5300 @ 1.73GHz (dual core) | ||||||
L1 cache enabled | OK | CPU: L1 I cache: 32K, L1 D cache: 32K | ||||||
L2 cache enabled | OK | L2 cache: 2048K | ||||||
L3 cache enabled | N/A | |||||||
Multiple CPU support | N/A | |||||||
Multi-core support | OK | Both cores show up in /proc/cpuinfo. | ||||||
Hardware virtualization | ? | |||||||
RAM | ||||||||
EDO | N/A | |||||||
SDRAM | N/A | |||||||
SO-DIMM | N/A | |||||||
DDR | N/A | |||||||
DDR2 | OK | Works fine, but currently you need to populate both RAM slots with DIMMs (of the same size?). | ||||||
DDR3 | N/A | |||||||
Dual channel support | N/A | |||||||
ECC support | ? | |||||||
On-board Hardware | ||||||||
On-board IDE 3.5" | OK | |||||||
On-board IDE 2.5" | N/A | |||||||
On-board SATA | ? | |||||||
On-board SCSI | N/A | |||||||
On-board USB | OK | Tested: USB thumb drive in all 4 backpanel USB ports. The onboard USB pin headers are untested, but should also work. | ||||||
On-board VGA | OK | You need to prepend the VGA blob from the proprietary BIOS for this to work. | ||||||
On-board Ethernet | WIP | The eth1 interface (in this case) works fine, but so far ifconfig -a only shows one of the three NICs (?) | ||||||
On-board Audio | WIP | Doesn't seem to work, yet. | ||||||
On-board Modem | N/A | |||||||
On-board FireWire | ? | |||||||
On-board Smartcard reader | N/A | |||||||
On-board CompactFlash | N/A | |||||||
On-board PCMCIA | N/A | |||||||
On-board Wifi | N/A | |||||||
On-board Bluetooth | N/A | |||||||
On-board SD card reader | N/A | |||||||
Add-on slots/cards | ||||||||
ISA add-on cards | N/A | |||||||
Audio/Modem-Riser (AMR/CNR) cards | N/A | |||||||
PCI add-on cards | ? | |||||||
Mini-PCI add-on cards | Unknown | |||||||
Mini-PCI-Express add-on cards | Unknown | |||||||
PCI-X add-on cards | Unknown | |||||||
AGP graphics cards | N/A | |||||||
PCI Express x1 add-on cards | N/A | |||||||
PCI Express x2 add-on cards | N/A | |||||||
PCI Express x4 add-on cards | N/A | |||||||
PCI Express x8 add-on cards | N/A | |||||||
PCI Express x16 add-on cards | ? | |||||||
PCI Express x32 add-on cards | N/A | |||||||
HTX add-on cards | N/A | |||||||
Legacy / Super I/O | ||||||||
Floppy | ? | |||||||
Serial port 1 (COM1) | OK | |||||||
Serial port 2 (COM2) | ? | |||||||
Parallel port | OK | Doing modprobe ppdev works, but no further test were performed. | ||||||
PS/2 keyboard | OK | |||||||
PS/2 mouse | ? | |||||||
Game port | N/A | |||||||
Infrared | ? | |||||||
PC speaker | OK | |||||||
DiskOnChip | N/A | |||||||
Input | ||||||||
Trackpoint | N/A | |||||||
Touchpad | N/A | |||||||
Fn Hotkeys | N/A | |||||||
Fingerprint Reader | N/A | |||||||
Laptop | ||||||||
Docking VGA | N/A | |||||||
Docking LAN | N/A | |||||||
Docking USB | N/A | |||||||
Docking Audio | N/A | |||||||
Docking Displayport | N/A | |||||||
Thinklight | N/A | |||||||
Webcam | N/A | |||||||
Miscellaneous | ||||||||
Sensors / fan control | OK | Works fine using the w83627hf and coretemp Linux kernel modules. | ||||||
Hardware watchdog | OK | Not yet actually tested, but it seems to be found: iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0560). | ||||||
SMBus | ? | |||||||
CAN bus | N/A | |||||||
CPU frequency scaling | ? | |||||||
Other powersaving features | N/A | |||||||
ACPI | ? | |||||||
Reboot | ? | |||||||
Poweroff | ? | Needs ACPI, thus won't work if you use acpi=off on the Linux kernel command line. | ||||||
Suspend | Unknown | |||||||
Nonstandard LEDs | N/A | |||||||
High precision event timers (HPET) | OK | The HPET is detected by Linux (hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0) and powertop output suggests that it works ok. | ||||||
Random number generator (RNG) | N/A | |||||||
Wake on modem ring | ? | |||||||
Wake on LAN | ? | |||||||
Wake on keyboard | ? | |||||||
Wake on mouse | ? | |||||||
TPM | Unknown | |||||||
Flashrom | OK | Works fine, but you have to use -m kontron:986lcd-m when booted with the vendor BIOS (not needed when booted with coreboot). |
Build tutorial
$ svn co svn://coreboot.org/repos/trunk/coreboot-v2 $ cd coreboot-v2/targets $ ./buildtarget kontron/986lcd-m $ cd kontron/986lcd-m/kontron_986lcd_m
Now copy your payload into the current directory and name it payload.elf. Then:
$ make -s
The resulting coreboot.rom is your coreboot ROM image you can flash using flashrom.
Notes
- If you use FILO, SATA will probably be hda and hdb, while hdc is the master drive of the IDE controller.
- Currently you have to use acpi=off on the kernel command line to make IDE work.
- If you experience kernel crashes try to blacklist the agpgart and intel_agp kernel modules.
- TODO: Add notes for proper (onboard) VGA setup.
![]() |
I, the copyright holder of this work, hereby release it into the public domain. This applies worldwide.
In case this is not legally possible: |