The wiki is being retired!
Documentation is now handled by the same processes we use for code: Add something to the Documentation/ directory in the coreboot repo, and it will be rendered to https://doc.coreboot.org/. Contributions welcome!
Before starting to work on coreboot support for a new mainboard and/or chipset you'll want a few development tools (both hardware and software). Not all of them are strictly required, a lot depends on your specific task and needs.
- 1 Basic requirements
- 2 In case of extra soldered BIOS chip
- 3 Flash chip related
- 4 Artecgroup programmable LPC dongle
- 5 Oscilloscope
- 6 In Circuit Emulator hardware debugger
- 7 EPROM emulators
- 8 Getting some output
- 9 Other
- A mainboard you want to port coreboot to, preferably with long manufacturing lifespan.
- A development machine (ideally separate from your target system, though there are some mavericks who use the target for development)
It's also handy to have one/some/all of the following:
In case of extra soldered BIOS chip
sudo flashrom -p internal -w new.bin [...] Error: Image size doesn't match) if the size of the hardware chip mismatch the Coreboot image configured ROM chip size. This is a good thing as it will save you from accidentally burning Cooreboot to the primary chip if you forget to toggle the hardware switch to the secondary chip. Chips with equal size will likely make you break the board one day. You have been warned!
PC Engines lpc1A
This board is most useful if you are working on machines from the ALIX family, but could also be useful if you can expose an LPC header on another board.
External EPROM/Flash programmer that can program the flash chip on your motherboard
External programmers are not always necessary. Use your mainboard as a programmer instead. Boot up with a known-good image, then unplug the (DIP32, PLCC32, or DIP8) ROM chip while powered on. Reflash that secondary piece and try a reboot. Many boards allow for more than one type of flash to be programmed, but clearly are less versatile than real programmers.
Many programmers are supported by flashrom:
- RTL8139 NIC (PCI network card) with 32 pin socket and the appropriate ZIF socket adapter with flashrom. this is a low cost approach. Check, whether flashrom will recognize your flash part in this scenario.
- Dediprog SF100:High speed spi programmer, can be used under both windows and linux(with flashrom). See SF100 Usage for detail description.
- Bus Pirate v3/v4: SPI programmer, similar to but less expensive than the Dediprog SF100. Really slow. If you're using it, try at least http://flashrom.org/Bus_Pirate#Speedup to get a somewhat acceptable speed out of it.
- Raspberry Pi (or any other development board with a fast SPI bus): SPI programmer, rougly as fast as the Dediprog SF100, but as cheap as the Bus Pirate.
Some programmers aren't and works with other software:
- GALEP-4: Has beta Linux drivers ~$300. See Galep IV for a description on how to get the more modern Windows software working in Linux with wine.
The BIOS Savior is a tool that plugs into and replaces the original mainboard Flash device. The BIOS Savior has its own Flash device and a socket for the original mainboard Flash device (PLCC or DIP versions are available). It features a switch to allow the developer to choose between which Flash device is accessed by the mainboard during read and write cycles.
This device helps to minimize the amount of hot swapping required and reduces mechanical and electrical stress on the BIOS chips.
The BIOS Savior is available from:
Top Hat Flash
A similar function is achieved by the Top Hat Flash which comes at no extra cost with many Elitegroup, and some GIGABYTE and Albatron mainboards like ECS KN3 SLI2 Extreme.
As you can guess from the photo to the side, it is two plcc sockets soldered together. The upper one carries a spare BIOS chip as a fallback / failsafe secondary bootable BIOS. By means of some 'obscure' cicuitry, the additional, secondary chip is being booted from, if you manually press / stick the TOP HAT FLASH onto your primary BIOS chip on the mainboard. Sadly, this simple technique does not seem to work with other boards right away.
After bootup, it can manually be lifted off the original BIOS chip, so the original BIOS can be reflashed after a failure. The RST# pin is wired to OE# on the spare chip, otherwise it's wired 1:1. Top Hat Flash is equipped with a Winbond W39V040AP FWH. It may rely on particular circuitry on the mainboard to operate.
You may DIY yours dual flash device. As an example look here: Developer Manual/Tools/Dual Flash
Chip removal tools
If you're hot-swapping your BIOS chips (i.e., removing the chip while your computer is running, then inserting another one) you'll usually need some tools.
There are different tools for DIP and PLCC chips (see photos). You can find them in most electronics stores, usually. Both types cost roughly 5-10 Euros.
Another very nifty idea is clipping off the needle point of normal office push pins, and then attaching them to (PLCC) ROM chips with super glue. That makes it pretty easy to insert and remove the ROM chips without extra tools.
Since after bootup, flash mem is not accessed anymore, you can even hot plug (plug in and out while PC powered on) push pin flashes. This way you save an external EEPROM programmer and mimic the procedure of top hat flash. Make sure you do not short circuit anything, though.
In Circuit chip programmer
Should allow you to program your BIOS even if it is soldered to the motherboard.
Artecgroup programmable LPC dongle
For hardware debugging purposes when it goes down the most atomic details. Consider logic analyzers as alternative.
In Circuit Emulator hardware debugger
Allows very time-saving burn/debug cycles with added tracing capabilities but somewhat costly.
These hardware devices pretend to be an EEPROM chip.
- http://www.linuxselfhelp.com/HOWTO/Diskless-HOWTO-10.html (a larger list -- outdated)
Getting some output
USB debug devices
An alternative to a serial console may be a USB debug device. They are not so common, yet. Their advantage is higher speed than a serial console. One might hook an FPGA to it for profiling purposes or some automated checks. Accessing a USB debug device from within BIOS is not different than other USB devices, and is part of the USB standard.
A POST card will save your life: it's the only output device (beside beeper) you have during the boot process.
Compact Flash IDE adaptor
Solid state disks (e.g. CompactFlash cards) save time during the repeated boot process compared with regular hard disks.
- http://www.hsc-us.com/industrial/adapter/ATP.html (2xCF, one with hotswap!)
- http://www.mesanet.com/ (Choose DISK EMULATORS then CFADPTHD in the menu. 2xCF)