Difference between revisions of "Board:kontron/986lcd-m"

From coreboot
Jump to: navigation, search
(SATA works with acpi=off, PS/2 mouse works.)
m
Line 30: Line 30:
 
|IDE_25_status = N/A
 
|IDE_25_status = N/A
 
|SATA_status = OK
 
|SATA_status = OK
|SATA_comments = Tested: SATA disk ('''hda1''' in [[FILO]], '''/dev/sda1''' in Linux), but you currently have to use '''acpi=off'''.
+
|SATA_comments = Tested: SATA disk ('''hda1''' in [[FILO]], '''/dev/sda1''' in Linux), but you currently have to use '''acpi=off''' or '''pci=noacpi'''.
 
|USB_status = OK
 
|USB_status = OK
|USB_comments = Tested: USB thumb drive in all 4 backpanel USB ports. The onboard USB pin headers are untested, but should also work.
+
|USB_comments = Tested: USB thumb drive in all 4 backpanel USB ports, as well as on the USB pin headers on the board ('''USB6_7''', see manual).
 
|Onboard_VGA_status = OK
 
|Onboard_VGA_status = OK
|Onboard_VGA_comments = You need to prepend the VGA blob from the proprietary BIOS for this to work.
+
|Onboard_VGA_comments = You need to prepend the VGA blob from the proprietary BIOS for this to work. Console works, X11 works (use the '''intel''' X.org driver).
 
|Onboard_ethernet_status = WIP
 
|Onboard_ethernet_status = WIP
 
|Onboard_ethernet_comments = The '''eth1''' interface (in this case) works fine, but so far '''ifconfig -a''' only shows one of the three NICs (?)
 
|Onboard_ethernet_comments = The '''eth1''' interface (in this case) works fine, but so far '''ifconfig -a''' only shows one of the three NICs (?)
Line 42: Line 42:
 
|Onboard_firewire_status = ?
 
|Onboard_firewire_status = ?
 
|Smartcard_status = N/A
 
|Smartcard_status = N/A
|Onboard_CF_status = N/A
+
|Onboard_CF_status = Untested
 +
|Onboard_CF_comments = There's an onboard CompactFlash slot on the back-side of the board.
 
|Onboard_PCMCIA_status = N/A
 
|Onboard_PCMCIA_status = N/A
 
|Onboard_SCSI_status = N/A
 
|Onboard_SCSI_status = N/A
Line 86: Line 87:
 
|HPET_comments = The HPET is detected by Linux ('''hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0''') and '''powertop''' output suggests that it works ok.
 
|HPET_comments = The HPET is detected by Linux ('''hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0''') and '''powertop''' output suggests that it works ok.
 
|RNG_status = N/A
 
|RNG_status = N/A
|WakeOnModem_status = ?
+
|WakeOnModem_status = N/A
|WakeOnLAN_status = ?
+
|WakeOnLAN_status = Untested
 +
|WakeOnLAN_comments = The board should support WOL according to the manual.
 
|WakeOnKeyboard_status = ?
 
|WakeOnKeyboard_status = ?
 
|WakeOnMouse_status = ?
 
|WakeOnMouse_status = ?

Revision as of 18:54, 19 December 2008

This page describes how to use coreboot on the Kontron 986LCD-M/mITX mainboard. It is maintained by Uwe Hermann.

Status

Device/functionality Status Comments
CPU
CPU works OK Intel(R) Core(TM)2 CPU T5300 @ 1.73GHz (dual core)
L1 cache enabled OK CPU: L1 I cache: 32K, L1 D cache: 32K
L2 cache enabled OK L2 cache: 2048K
L3 cache enabled N/A
Multiple CPU support N/A
Multi-core support OK Both cores show up in /proc/cpuinfo.
Hardware virtualization  ?
RAM
EDO N/A
SDRAM N/A
SO-DIMM N/A
DDR N/A
DDR2 OK Works fine, but currently you need to populate both RAM slots with DIMMs (of the same size?).
DDR3 N/A
Dual channel support N/A
ECC support  ?
On-board Hardware
On-board IDE 3.5" OK
On-board IDE 2.5" N/A
On-board SATA OK Tested: SATA disk (hda1 in FILO, /dev/sda1 in Linux), but you currently have to use acpi=off or pci=noacpi.
On-board SCSI N/A
On-board USB OK Tested: USB thumb drive in all 4 backpanel USB ports, as well as on the USB pin headers on the board (USB6_7, see manual).
On-board VGA OK You need to prepend the VGA blob from the proprietary BIOS for this to work. Console works, X11 works (use the intel X.org driver).
On-board Ethernet WIP The eth1 interface (in this case) works fine, but so far ifconfig -a only shows one of the three NICs (?)
On-board Audio WIP Doesn't seem to work, yet.
On-board Modem N/A
On-board FireWire  ?
On-board Smartcard reader N/A
On-board CompactFlash Untested There's an onboard CompactFlash slot on the back-side of the board.
On-board PCMCIA N/A
On-board Wifi N/A
On-board Bluetooth N/A
On-board SD card reader N/A
Add-on slots/cards
ISA add-on cards N/A
Audio/Modem-Riser (AMR/CNR) cards N/A
PCI add-on cards  ?
Mini-PCI add-on cards Unknown
Mini-PCI-Express add-on cards Unknown
PCI-X add-on cards Unknown
AGP graphics cards N/A
PCI Express x1 add-on cards N/A
PCI Express x2 add-on cards N/A
PCI Express x4 add-on cards N/A
PCI Express x8 add-on cards N/A
PCI Express x16 add-on cards  ?
PCI Express x32 add-on cards N/A
HTX add-on cards N/A
Legacy / Super I/O
Floppy  ?
Serial port 1 (COM1) OK
Serial port 2 (COM2)  ?
Parallel port OK Doing modprobe ppdev works, but no further test were performed.
PS/2 keyboard OK
PS/2 mouse OK
Game port N/A
Infrared  ?
PC speaker OK
DiskOnChip N/A
Input
Trackpoint N/A
Touchpad N/A
Fn Hotkeys N/A
Fingerprint Reader N/A
Laptop
Docking VGA N/A
Docking LAN N/A
Docking USB N/A
Docking Audio N/A
Docking Displayport N/A
Thinklight N/A
Webcam N/A
Miscellaneous
Sensors / fan control OK Works fine using the w83627hf and coretemp Linux kernel modules.
Hardware watchdog OK Not yet actually tested, but it seems to be found: iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0560).
SMBus  ?
CAN bus N/A
CPU frequency scaling  ?
Other powersaving features N/A
ACPI  ?
Reboot  ?
Poweroff  ? Needs ACPI, thus won't work if you use acpi=off on the Linux kernel command line.
Suspend Unknown
Nonstandard LEDs N/A
High precision event timers (HPET) OK The HPET is detected by Linux (hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0) and powertop output suggests that it works ok.
Random number generator (RNG) N/A
Wake on modem ring N/A
Wake on LAN Untested The board should support WOL according to the manual.
Wake on keyboard  ?
Wake on mouse  ?
TPM Unknown
Flashrom OK Works fine, but you have to use -m kontron:986lcd-m when booted with the vendor BIOS (not needed when booted with coreboot).

Build tutorial

$ svn co svn://coreboot.org/repos/trunk/coreboot-v2
$ cd coreboot-v2/targets
$ ./buildtarget kontron/986lcd-m
$ cd kontron/986lcd-m/kontron_986lcd_m

Now copy your payload into the current directory and name it payload.elf. Then:

$ make -s

The resulting coreboot.rom is your coreboot ROM image you can flash using flashrom.

Notes

  • If you use FILO, SATA will probably be hda and hdb, while hdc is the master drive of the IDE controller.
  • Currently you have to use acpi=off on the kernel command line to make IDE work.
  • If you experience kernel crashes try to blacklist the agpgart and intel_agp kernel modules.
  • TODO: Add notes for proper (onboard) VGA setup.
Error creating thumbnail: Unable to save thumbnail to destination
I, the copyright holder of this work, hereby release it into the public domain. This applies worldwide.

In case this is not legally possible:
I grant anyone the right to use this work for any purpose, without any conditions, unless such conditions are required by law.