Nokia IP330

From coreboot
Revision as of 21:24, 28 January 2011 by MBertens (talk | contribs) (J10)
Jump to: navigation, search

The wiki is being retired!

Documentation is now handled by the same processes we use for code: Add something to the Documentation/ directory in the coreboot repo, and it will be rendered to Contributions welcome!

This page lists the coreboot status of the Nokia IP530 mainboard. It's maintained by Marc Bertens.

The Nokia IP330 is originally a Firewall that runs on the proprietary IPSO operating system of Nokia, it was based in the FreeBSD operating system. There is as far as I known no CD support in the orginal BIOS.

The System has no VGA, all console activity must be done through a serial console. At the front the following can be found;

  • Power LED
  • Fault LED
  • 2 Serial interfaces COM1 and COM2
  • 3 Ethernet RJ45 sockets
  • Reset button
  • 1 Compact PCI slot

At the back the following can be found;

  • EURO Power connector
  • Power switch
  • Three FANs for system unit cooling
  • One FAN for CPU cooling

Development status

The current development status is; No coreboot running yet

Hardware status

Device/functionality Status Comments
CPU works WIP K6
L1 cache enabled WIP
L2 cache enabled WIP
L3 cache enabled N/A
Multiple CPU support N/A
Multi-core support N/A
Hardware virtualization N/A
Dual channel support N/A
ECC support WIP
On-board Hardware
On-board IDE 3.5" OK One IDE connector on-board
On-board IDE 2.5" N/A
On-board SATA N/A
On-board SCSI N/A
On-board USB N/A
On-board VGA N/A
On-board Ethernet WIP Three intel SB82558B controllers.
On-board Audio N/A
On-board Modem N/A
On-board FireWire N/A
On-board Smartcard reader N/A
On-board CompactFlash N/A
On-board PCMCIA N/A
On-board Wifi N/A
On-board Bluetooth N/A
On-board SD card reader N/A
Add-on slots/cards
ISA add-on cards N/A
Audio/Modem-Riser (AMR/CNR) cards N/A
PCI add-on cards WIP
Mini-PCI add-on cards N/A
Mini-PCI-Express add-on cards Unknown
PCI-X add-on cards N/A
AGP graphics cards N/A
PCI Express x1 add-on cards N/A
PCI Express x2 add-on cards N/A
PCI Express x4 add-on cards N/A
PCI Express x8 add-on cards N/A
PCI Express x16 add-on cards N/A
PCI Express x32 add-on cards N/A
HTX add-on cards N/A
Legacy / Super I/O
Floppy N/A
Serial port 1 (COM1) OK
Serial port 2 (COM2) OK
Parallel port N/A
PS/2 keyboard N/A
PS/2 mouse N/A
Game port N/A
Infrared N/A
PC speaker N/A
DiskOnChip N/A
Trackpoint N/A
Touchpad N/A
Fn Hotkeys N/A
Fingerprint Reader N/A
Docking VGA N/A
Docking LAN N/A
Docking USB N/A
Docking Audio N/A
Docking Displayport N/A
Thinklight N/A
Webcam N/A
Sensors / fan control WIP
Hardware watchdog N/A
CAN bus N/A
CPU frequency scaling N/A
Other powersaving features N/A
ACPI No There's no ACPI implementation for this board, but it's on our TODO list.
Reboot N/A
Poweroff N/A
Suspend Unknown
Nonstandard LEDs WIP Special-purpose LED available on the board, Fault is controlled by the superio?
High precision event timers (HPET) N/A
Random number generator (RNG) N/A
Wake on modem ring N/A
Wake on LAN N/A
Wake on keyboard N/A
Wake on mouse N/A
TPM Unknown
Flashrom WIP Supported flashrom revision will be higher than 1257.

System Setup

On board of the IP530 can be found the following:

  • CPU: Socket 7, AMD K6 II at 266 MHz normally,
    • Some later models of the IP330 had a K6 II at 500 or 550 MHz. Special cooling shroud needed on those.
  • I430TX northbridge.
  • 82371 southbridge.
  • intel 21150 PCI to PCI bridge.
  • 28F200, 256 Kbyte flashrom.
  • SMSC FDC37B932QF superio with 1024 bits SPI eeprom attached.
  • LM72 temp controller.
  • 3 intel 82558B ethernet controllers.
  • 2 SD-RAM sockets.
    • 64 Mb SDRAM by default. Definitely takes a 256 Mb PC133 fine, and rumoured to take a maximum of 512 Mb SDRAM.
    • On early models there is one SDRAM slot, and solder pads for a second. Later models have both slots.

Below the description is given for the following;

  • For the connectors on the mainboard of the Nokia IP330, due missing documentation of the manufacturer.
  • To create a flash option board on the J-DEBUG connector.
  • The layout of the SPI eeprom behind the SuperIO.


The J10 Floppy connector

Connectors & jumpers

  • JP1
    • 1-2 = short reset CMOS ?
  • JP2 (besides CPU, not soldered in)
    • 1-2
    • 3-4
    • 5-6
  • JP3
    • 1-2 = P or E mode
    • 2-3 = All BLK locked (default)
  • JP4
    • 1-2 = B.B. Unlocked
    • 2-3 = B.B locked (default)
  • JP5
  • JP6
    • 1-6 B.B. Locked (default)
    • 2-5 B.B. Unlocked
    • 3-4 B.B. DPD Locked
  • JP11-JP13 Serial port COM2
  • JP12-JP14 Internal modem
  • J1 Backplane CPU fan
  • J2 Backplane system fan
  • J3 Backplane system fan
  • J4 Backplane system fan
  • J5 CPU fan (not used)
  • J9 IDE connector
  • J15 Serial port connector (ML10), COM2
  • J16 Phone connector (behind front)
  • J17 Ethernet RJ45 connector eth s3
  • J18 Ethernet RJ45 connector eth s4
  • J19 Ethernet RJ45 connector eth s5
  • P1 option power connector
  • P2 IDE power connector
  • P3 Serial port connector (DB9), COM1
  • P6 Power connector

Front LED

EEPROM behide the SuperIO

EEPROM information
address range length Content Description
0x00-0x05 6 bytes IP530\x00 Product name
0x06-0x13 14 bytes 0x55 Filler
0x14-0x17 4 bytes 0x05,0x00,0x00,0x00 Unknown
0x18-0x1B 4 bytes 0x04,0x00,0x00,0x00 Unknown
0x1C-0x1F 4 bytes 0x03,0x00,0x00,0x00 Unknown
0x20-0x23 4 bytes 0x10,0x00,0x00,0x00 Unknown
0x24-0x29 6 bytes - Board number, sticker close to the PIII cpu
0x2A-0x37 14 bytes - Mfg. P/n (on the bottom side of the unit), filled out with spaces
0x38-0x3D 6 bytes 0x55 Filler
0x3E-0x3F 2 bytes 0xYY,0x00 Mfg. rev. (on the bottom side of the unit), 0xYY = is the revision letter, where A = 0x41, B = 0x42
0x40-0x51 18 bytes 0x55 Filler
0x52-0x5D 12 bytes - Serial number (on the bottom side of the unit)
0x5E-0x7D 32 bytes 0x55 Filler
0x7E-0x7F 2 bytes 0xFF,0xFF Unknown, probably the checksum value, but not used therefore filled 0xFFFF

On coreboot startup the eeprom is read, to determine if its a IP530, otherwise it get signaled. And the revision of the hardware. When its reads an unknown (at that time) herdware revision, revision B will be assumed.

Be aware when accessing the data the addresses above are byte address, they need to be converted in word addresses.