boot problem with compact flash

[Serafino Sorrenti]

Command? Max cpuid index    : 1
Command? Vendor ID          : AuthenticAMD
Command? Processor Type     : 0x00
Command? Processor Family   : 0x06
>>>>> 
>>>>> Too many errors encountered; the rest of the message is ignored:
> Processor Model    : 0x08
> Processor Mask     : 0x00
> Processor Stepping : 0x00
> Feature flags      : 0x0183f9ff
> 
> 
> MTRR check
> Fixed MTRRs   : Enabled
> Variable MTRRs: Enabled
> 
> Disabling local apic...done.
> CPU #0 Initialized
> Allocating PCI resources...
> ASSIGN RESOURCES, bus 0
> PCI: 00:00.0 10 <- [0xf8000000 - 0xfbffffff] mem
> PCI: 00:00.1 10 <- [0x00002c90 - 0x00002c93] io
> PCI: 00:00.1 14 <- [0x00002ca0 - 0x00002ca3] io
> PCI: 00:00.1 18 <- [0x00002cb0 - 0x00002cb3] io
> PCI: 00:00.1 1c <- [0x00002cc0 - 0x00002cc3] io
> PCI: 00:00.1 20 <- [0x00002c80 - 0x00002c8f] io
> PCI: 00:01.1 10 <- [0x00002000 - 0x000020ff] io
> PCI: 00:01.1 14 <- [0xfc100000 - 0xfc100fff] mem
> PCI: 00:01.2 10 <- [0xfc101000 - 0xfc101fff] mem
> PCI: 00:01.3 10 <- [0xfc102000 - 0xfc102fff] mem
> PCI: 00:01.4 10 <- [0x00002400 - 0x000024ff] io
> PCI: 00:01.4 14 <- [0xfc103000 - 0xfc103fff] mem
> PCI: 00:01.6 10 <- [0x00002800 - 0x000028ff] io
> PCI: 00:01.6 14 <- [0x00002c00 - 0x00002c7f] io
> PCI: 00:02.0 1c <- [0x00001000 - 0x00001fff] bus 1 ÿÿÿÿÿÿio
> PCI: 00:02.0 24 <- [0xf0000000 - 0xf7ffffff] bus 1 ÿÿÿÿÿÿprefmem
> PCI: 00:02.0 20 <- [0xfc000000 - 0xfc0fffff] bus 1 ÿÿÿÿÿÿmem
> ASSIGN RESOURCES, bus 1
> PCI: 01:00.0 10 <- [0xf0000000 - 0xf7ffffff] prefmem
> PCI: 01:00.0 14 <- [0xfc000000 - 0xfc01ffff] mem
> PCI: 01:00.0 18 <- [0x00001000 - 0x0000107f] io
> Allocating VGA resource
> done.
> Enabling PCI resourcess...PCI: 00:00.0 cmd <- 07
> PCI: 00:00.1 cmd <- 01
> PCI: 00:01.0 cmd <- 0c
> PCI: 00:01.1 cmd <- 03
> PCI: 00:01.2 cmd <- 02
> PCI: 00:01.3 cmd <- 02
> PCI: 00:01.4 cmd <- 03
> PCI: 00:01.6 cmd <- 01
> PCI: 00:02.0 cmd <- 27PCI: 01:00.0 cmd <- 03
> done.
> Initializing PCI devices...
> PCI devices initialized
> Enabled in SIS 503 regs 0x40 and 0x45
> handle_superio start, s 0000b040 nsuperio 1 s->super 0000b318
> handle_superio Pass 1, check #0, s 0000b040 s->super 0000b318
> handle_superio: Pass 1, Superio SiS 950
> handle_superio  port 0x2e, defaultport 0x2e
> handle_superio  Using port 0x2e
> handle_superio Pass 1, done #0
> handle_superio done
> PCCHIPS M810LMR (and similar)...Entering the initregs process
> Southbridge fixup done for SIS 503
> handle_superio start, s 0000b040 nsuperio 1 s->super 0000b318
> handle_superio Pass 2, check #0, s 0000b040 s->super 0000b318
> handle_superio: Pass 2, Superio SiS 950
> handle_superio  port 0x2e, defaultport 0x2e
> handle_superio  Using port 0x2e
>   Call finishup
> handle_superio Pass 2, done #0
> handle_superio done
> Copying IRQ routing tables to 0xf0000...done.
> Wrote linuxbios table at: 00000500 - 0000066c  checksum bc14
> 
> Welcome to elfboot, the open sourced starter.
> January 2002, Eric Biederman.
> Version 1.2
> 
>     37:init_bytes() - zkernel_start:0xfffc0000  zkernel_mask:0x0000ffff
> Found ELF candiate at offset 0
> New segment addr 0x400000 size 0xcba0 offset 0x60 filesize 0x8789
> (cleaned up) New segment addr 0x400000 size 0xcba0 offset 0x60 filesize 
0x8789
> Loading Segment: addr: 0x0000000000400000 memsz: 0x000000000000cba0 filesz: 
> 0x0000000000008789
> Clearing Segment: addr: 0x0000000000408789 memsz: 0x0000000000004417
> Jumping to boot code
> ROM segment 0x0000 length 0x0000 reloc 0x0000
> Etherboot 5.0.6 (GPL) ELF for [SIS900]
> Boot from (N)etwork or from (L)ocal? clocks_per_tick = 941374
> N
> I am now initializing the ide system
> init_drive sectors_per_track = [32], num_heads = [16],num_cylinders=[984], 
> num_sectors = [503808]
> LBA mode supported
> 
> Boot: (hd0,0)/kernel
> rawread (post_loop) ide_read_sector failed
> File not found
> Probing...[SIS900]Found SIS900 ROM address 0x0000
> The PCI BIOS has not enabled this device!
> Updating PCI command 0003->0007. pci_bus 00 pci_device_fn 09
> Found SIS 85C503/5513 PCI to ISA bridge ROM address 0x0000
> 
> sis900_probe: MAC addr 00:0A:E6:4B:4A:AF at ioaddr 0X2000
> sis900_probe: Vendor:0X1039 Device:0X0900
> sis900_probe: No MII transceivers found!
> No adapter found
> <sleep>
> <abort>
> Boot from (N)etwork or from (L)ocal? N
> I am now initializing the ide system
> init_drive sectors_per_track = [32], num_heads = [16],num_cylinders=[984], 
> num_sectors = [503808]
> LBA mode supported
> 
> Boot: (hd0,0)/kernel
> File not found
> Probing...[SIS900]Found SIS900 ROM address 0x0000
> Found SIS 85C503/5513 PCI to ISA bridge ROM address 0x0000
> 
> sis900_probe: MAC addr 00:0A:E6:4B:4A:AF at ioaddr 0X2000
> sis900_probe: Vendor:0X1039 Device:0X0900
> sis900_probe: No MII transceivers found!
> No adapter found
> <sleep>
> <abort>
> Boot from (N)etwork or from (L)ocal? N
> I am now initializing the ide system
> init_drive sectors_per_track = [32], num_heads = [16],num_cylinders=[984], 
> num_sectors = [503808]
> LBA mode supported
> 
> Boot: (hd0,0)/kernel
> File not found
> Probing...[SIS900]Found SIS900 ROM address 0x0000
> Found SIS 85C503/5513 PCI to ISA bridge ROM address 0x0000
> 
> sis900_probe: MAC addr 00:0A:E6:4B:4A:AÆ
> 
> 
> 
> 
> 
> this is the error on boot in my serial console, but in the Compact flash the 
> file /kernel is here and don't have any problem.
> 
> Tnx Serafino