[LinuxBIOS] tyan s2881 - partial success
Ward Vandewege
ward at gnu.org
Fri Dec 16 05:30:22 CET 2005
So, with some help from Yinghai today, I finally managed to make my own
working LinuxBIOS image, and boot it on the s2881. Fantastic!
It cut boot time roughly in half - and that's without doing any optimizing of
the init startup sequence, which now takes up the bulk of the bootup time.
Anyway. Once the system booted, I tested network access and a few other
things, and everything seemed to work just fine.
But 10 minutes later the machine was no longer pingable, and I didn't get any
response on the serial console anymore either.
I shut it down, and restarted with LinuxBIOS. At this point, it would not
boot anymore - as you can see in the attached serial log, it just decides to
restart its fallback image just after init starts, which then hangs the box.
Any clues? This is the latest svn revision (2145), with Etherboot 5.4.1 +
FILO to boot from the local SATA drive.
I rebooted with the proprietary BIOS, which brought the box up just fine
(after complaining that it had to reset the CMOS). It started re-syncing the
software RAID array right after boot though, so maybe that is related to the
linuxBIOS hang upon boot, which is right after the kernel starts the RAID
devices?
I won't be able to work more on the box for the next week or two
(holidays...), but I thought I'd better signal this now.
Thanks,
Ward.
--
Ward Vandewege <ward at fsf.org>
Free Software Foundation - Senior System Administrator
-------------- next part --------------
LinuxBIOS-1.1.8_s2881_Fallback Thu Dec 15 18:45:48 EST 2005 starting...
(0,1) link=00
(1,0) link=00
02 nodes initialized.
core0: --- { APICID = 02 NODEID = 01 COREID = 00} ---
SBLink=02
NC node|link=02
ht reset -
LinuxBIOS-1.1.8_s2881_Fallback Thu Dec 15 18:45:48 EST 2005 starting...
(0,1) link=00
(1,0) link=00
02 nodes initialized.
core0: --- { APICID = 02 NODEID = 01 COREID = 00} ---
SBLink=02
NC node|link=02
Ram1.00
Ram1.01
Ram2.00
Ram2.01
Ram3
Initializing memory: done
Initializing memory: done
Ram4
v_esp=000cfd40
cpu_reset = 00000000
Clearing initial memory region: No cache as ram now - Use Ram as Stack now - done
new_cpu_reset = 00000000
Copying LinuxBIOS to ram.
src=fffe0004
dst=00004000
linxbios_ram.bin length = 0001928c
Jumping to LinuxBIOS.
LinuxBIOS-1.1.8_s2881_Fallback Thu Dec 15 18:45:48 EST 2005 booting...
Enumerating buses...
APIC_CLUSTER: 0 enabled
PCI_DOMAIN: 0000 enabled
PCI: 00:18.3 siblings=1
CPU: APIC: 00 enabled
CPU: APIC: 01 enabled
PCI: 00:19.0 [1022/1100] enabled
PCI: 00:19.1 [1022/1101] enabled
PCI: 00:19.2 [1022/1102] enabled
PCI: 00:19.3 [1022/1103] enabled
PCI: 00:19.3 siblings=1
CPU: APIC: 02 enabled
CPU: APIC: 03 enabled
PCI: pci_scan_bus for bus 0
PCI: 00:18.0 [1022/1100] enabled
PCI: 00:18.1 [1022/1101] enabled
PCI: 00:18.2 [1022/1102] enabled
PCI: 00:18.3 [1022/1103] enabled
PCI: 00:19.0 [1022/1100] enabled
PCI: 00:19.1 [1022/1101] enabled
PCI: 00:19.2 [1022/1102] enabled
PCI: 00:19.3 [1022/1103] enabled
PCI: 01:00.0 [1022/7450] enabled
PCI: 01:01.0 [1022/7450] enabled next_unitid: 0003
PCI: 01:00.0 [1022/7460] enabled
PCI: 01:03.0 [1022/7460] enabled next_unitid: 0007
PCI: pci_scan_bus for bus 1
PCI: 01:01.0 [1022/7450] enabled
PCI: 01:01.1 [1022/7451] enabled
PCI: 01:02.0 [1022/7450] enabled
PCI: 01:02.1 [1022/7451] enabled
PCI: 01:03.0 [1022/7460] enabled
PCI: 01:04.0 [1022/7468] enabled
PCI: 01:04.1 [1022/7469] enabled
PCI: 01:04.2 [1022/746a] enabled
PCI: 01:04.3 [1022/746b] enabled
PCI: pci_scan_bus for bus 2
PCI: 02:09.0 [14e4/1648] enabled
PCI: 02:09.1 [14e4/1648] enabled
Disabling static device: PCI: 02:0a.0
Disabling static device: PCI: 02:0a.1
PCI: pci_scan_bus returning with max=02
PCI: 02: 100MHz PCI-X
PCI: pci_scan_bus for bus 3
PCI: pci_scan_bus returning with max=03
PCI: 03: 133MHz PCI-X
PCI: pci_scan_bus for bus 4
PCI: 04:00.0 [1022/7464] enabled
PCI: 04:00.1 [1022/7464] enabled
PCI: 04:05.0 [1095/3114] enabled
PCI: 04:06.0 [1002/4752] enabled
PCI: pci_scan_bus returning with max=04
PNP: 002e.0 enabled
PNP: 002e.1 disabled
PNP: 002e.2 enabled
PNP: 002e.3 disabled
PNP: 002e.5 enabled
PNP: 002e.6 disabled
PNP: 002e.7 disabled
PNP: 002e.8 disabled
PNP: 002e.9 disabled
PNP: 002e.a disabled
PNP: 002e.b enabled
smbus: PCI: 01:04.3[0]->I2C: 01:50 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:51 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:52 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:53 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:54 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:55 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:56 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:57 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:2d enabled
smbus: PCI: 01:04.3[0]->I2C: 01:2a enabled
smbus: PCI: 01:04.3[0]->I2C: 01:49 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:4a enabled
PCI: pci_scan_bus returning with max=04
PCI: pci_scan_bus returning with max=04
done
Allocating resources...
Reading resources...
PCI: 01:01.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 2 io
PCI: 01:01.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 2 prefmem
PCI: 01:03.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 4 prefmem
Done reading resources.
Setting resources...
PCI: 00:18.0 1ba <- [0x00fd300000 - 0x00fd2fffff] prefmem <node 0 link 2>
PCI: 00:18.0 1c2 <- [0x0000001000 - 0x0000002fff] io <node 0 link 2>
PCI: 00:18.0 1b2 <- [0x00fc000000 - 0x00fd2fffff] mem <node 0 link 2>
PCI: 01:01.0 20 <- [0x00fd100000 - 0x00fd1fffff] bus 2 mem
PCI: 02:09.0 10 <- [0x00fd100000 - 0x00fd10ffff] mem64
PCI: 02:09.0 18 <- [0x00fd110000 - 0x00fd11ffff] mem64
PCI: 02:09.1 10 <- [0x00fd120000 - 0x00fd12ffff] mem64
PCI: 02:09.1 18 <- [0x00fd130000 - 0x00fd13ffff] mem64
PCI: 01:01.1 10 <- [0x00fd200000 - 0x00fd200fff] mem64
PCI: 01:02.1 10 <- [0x00fd201000 - 0x00fd201fff] mem64
PCI: 01:03.0 1c <- [0x0000001000 - 0x0000001fff] bus 4 io
PCI: 01:03.0 20 <- [0x00fc000000 - 0x00fd0fffff] bus 4 mem
PCI: 04:00.0 10 <- [0x00fd000000 - 0x00fd000fff] mem
PCI: 04:00.1 10 <- [0x00fd001000 - 0x00fd001fff] mem
PCI: 04:05.0 10 <- [0x0000001410 - 0x0000001417] io
PCI: 04:05.0 14 <- [0x0000001430 - 0x0000001433] io
PCI: 04:05.0 18 <- [0x0000001420 - 0x0000001427] io
PCI: 04:05.0 1c <- [0x0000001440 - 0x0000001443] io
PCI: 04:05.0 20 <- [0x0000001400 - 0x000000140f] io
PCI: 04:05.0 24 <- [0x00fd003000 - 0x00fd0033ff] mem
PCI: 04:06.0 10 <- [0x00fc000000 - 0x00fcffffff] mem
PCI: 04:06.0 14 <- [0x0000001000 - 0x00000010ff] io
PCI: 04:06.0 18 <- [0x00fd002000 - 0x00fd002fff] mem
PCI: 04:06.0 30 <- [0x00fff80000 - 0x00fff9ffff] romem
PNP: 002e.0 60 <- [0x00000003f0 - 0x00000003f7] io
PNP: 002e.0 70 <- [0x0000000006 - 0x0000000006] irq
PNP: 002e.0 74 <- [0x0000000002 - 0x0000000002] drq
PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] io
PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] irq
PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io
PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io
PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq
PNP: 002e.5 72 <- [0x000000000c - 0x000000000c] irq
PNP: 002e.b 60 <- [0x0000000290 - 0x0000000297] io
PNP: 002e.b 70 <- [0x0000000005 - 0x0000000005] irq
PCI: 01:04.1 20 <- [0x0000002420 - 0x000000242f] io
PCI: 01:04.2 10 <- [0x0000002400 - 0x000000241f] io
PCI: 01:04.3 58 <- [0x0000002000 - 0x00000020ff] io
PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart>
PCI: 00:19.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart>
Done setting resources.
Done allocating resources.
Enabling resourcess...
PCI: 00:18.0 cmd <- 140
PCI: 01:01.0 bridge ctrl <- 0003
PCI: 01:01.0 cmd <- 146
PCI: 02:09.0 subsystem <- 10f1/2881
PCI: 02:09.0 cmd <- 142
PCI: 02:09.1 subsystem <- 10f1/2881
PCI: 02:09.1 cmd <- 142
PCI: 01:01.1 subsystem <- 10f1/2881
PCI: 01:01.1 cmd <- 146
PCI: 01:02.1 subsystem <- 10f1/2881
PCI: 01:02.1 cmd <- 146
PCI: 01:03.0 bridge ctrl <- 0003
PCI: 01:03.0 cmd <- 147
PCI: 04:00.0 subsystem <- 10f1/2881
PCI: 04:00.0 cmd <- 142
PCI: 04:00.1 subsystem <- 10f1/2881
PCI: 04:00.1 cmd <- 142
PCI: 04:05.0 subsystem <- 10f1/2881
PCI: 04:05.0 cmd <- 143
PCI: 04:06.0 subsystem <- 10f1/2881
PCI: 04:06.0 cmd <- 1c3
PCI: 01:04.0 subsystem <- 10f1/2881
PCI: 01:04.0 cmd <- 14f
w83627hf hwm smbus enabled
PCI: 01:04.1 subsystem <- 10f1/2881
PCI: 01:04.1 cmd <- 141
PCI: 01:04.2 subsystem <- 10f1/2881
PCI: 01:04.2 cmd <- 141
PCI: 01:04.3 subsystem <- 10f1/2881
PCI: 01:04.3 cmd <- 141
PCI: 00:18.1 subsystem <- 10f1/2881
PCI: 00:18.1 cmd <- 140
PCI: 00:18.2 subsystem <- 10f1/2881
PCI: 00:18.2 cmd <- 140
PCI: 00:18.3 cmd <- 140
PCI: 00:19.0 cmd <- 140
PCI: 00:19.1 cmd <- 140
PCI: 00:19.2 cmd <- 140
PCI: 00:19.3 cmd <- 140
done.
Initializing devices...
Root Device init
APIC_CLUSTER: 0 init
Initializing CPU #0
CPU: vendor AMD device 20f12
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
microcode: patch id that want to apply= 0x0000004d
microcode: updated to patch id = 0x0000004d success
Setting up local apic... apic_id: 0 done.
Clearing memory 1024K - 2097152K: ------------------------------- done
CPU #0 Initialized
start_eip=0x00010000
Initializing CPU #1
CPU: vendor AMD device 20f12
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
microcode: patch id that want to apply= 0x0000004d
microcode: updated to patch id = 0x0000004d success
Setting up local apic... apic_id: 1 done.
CPU #1 Initialized
start_eip=0x00010000
Initializing CPU #2
CPU: vendor AMD device 20f12
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
microcode: patch id that want to apply= 0x0000004d
microcode: updated to patch id = 0x0000004d success
Setting up local apic... apic_id: 2 done.
Clearing memory 2097152K - 5242880K: ----------------++++++++++++++++ done
CPU #2 Initialized
start_eip=0x00010000
Initializing CPU #3
Waiting for 1 CPUS to stop
CPU: vendor AMD device 20f12
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
microcode: patch id that want to apply= 0x0000004d
microcode: updated to patch id = 0x0000004d success
Setting up local apic... apic_id: 3 done.
CPU #3 Initialized
All AP CPUs stopped
PCI: 00:18.0 init
PCI: 01:01.0 init
PCI: 02:09.0 init
PCI: 02:09.1 init
PCI: 01:03.0 init
PCI: 04:05.0 init
PCI: 04:06.0 init
PCI: 01:04.0 init
RTC Init
Invalid CMOS LB checksum
enabling HPET @0xfed00000
PNP: 002e.0 init
PNP: 002e.2 init
PNP: 002e.5 init
PNP: 002e.b init
PCI: 01:04.1 init
IDE1 IDE0 PCI: 01:04.3 init
set power on after power fail
smbus: PCI: 01:04.3[0]->I2C: 01:2d init
PCI: 00:18.1 init
PCI: 00:18.2 init
PCI: 00:18.3 init
NB: Function 3 Misc Control.. done.
PCI: 00:19.0 init
PCI: 00:19.1 init
PCI: 00:19.2 init
PCI: 00:19.3 init
NB: Function 3 Misc Control.. done.
Devices initialized
Writing IRQ routing tables to 0xf0000...done.
Wrote the mp table end at: 00000020 - 000001f4
Moving GDT to 0x500...ok
Wrote linuxbios table at: 00000530 - 00000e1c checksum 2ea0
Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3
33:stream_init() - rom_stream: 0xfffc0000 - 0xfffdffff
Found ELF candiate at offset 0
Loading Etherboot version: 5.4.1
Dropping non PT_LOAD segment
New segment addr 0x10000 size 0x49100 offset 0x0 filesize 0x9ac0
(cleaned up) New segment addr 0x10000 size 0x49100 offset 0x0 filesize 0x9ac0
Loading Segment: addr: 0x00000000bff8c000 memsz: 0x0000000000034000 filesz: 0x0000000000009ac0
Clearing Segment: addr: 0x00000000bff95ac0 memsz: 0x000000000002a540
Loading Segment: addr: 0x0000000000044000 memsz: 0x0000000000015100 filesz: 0x0000000000000000
Clearing Segment: addr: 0x0000000000044000 memsz: 0x0000000000015100
Jumping to boot code at 0x100b0
CPU 2063 Mhz
Etherboot 5.4.1 (GPL) http://etherboot.org
Drivers: TG3 FILO Images: NBI ELF
Protocols: DHCP TFTP
Relocating _text from: [000101b0,00059100) to [bfeb70b0,bff00000)
Boot from (N)etwork (D)isk or (Q)uit? D
Probing pci disk...
[FILO]FILO version 0.4.1 (root at countzero.vandewege.net) Thu Dec 15 18:44:50 EST 2005
Press <Enter> for default boot, or <Esc> for boot prompt... 2 1
boot: hde1:/vmlinuz-2.6.12-9-amd64-generic initrd=/initrd.img-2.6.12-9-amd64-generic ro root=/dev/md3 console=tty0 console=ttyS0,115200n8
hde: LBA48: WDC WD740GD-00FLC0
hdf: LBA48: WDC WD740GD-00FLC0
Mounted ext2fs
Found Linux version 2.6.12-9-amd64-generic (buildd at king) #1 Mon Oct 10 13:27:39 BST 2005 bzImage.
Loading kernel... ok
Loading initrd... ok
Jumping to entry point...
[ 0.000000] Bootdata ok (command line is ro root=/dev/md3 console=tty0 console=ttyS0,115200n8)
[ 0.000000] Linux version 2.6.12-9-amd64-generic (buildd at king) (gcc version 3.4.5 20050809 (prerelease) (Ubuntu 3.4.4-6ubuntu8)) #1 Mon Oct 10 13:27:39 BST 2005
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 0000000000000e7c type 16
[ 0.000000] BIOS-e820: 0000000000000e7c - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 00000000000f0400 type 16
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000c0000000 (usable)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
[ 0.000000] ACPI: Unable to locate RSDP
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] Virtual Wire compatibility mode.
[ 0.000000] OEM ID: TYAN <6>Product ID: S2881 <6>APIC at: 0xFEE00000
[ 0.000000] Processor #0 15:1 APIC version 16
[ 0.000000] Processor #1 15:1 APIC version 16
[ 0.000000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
[ 0.000000] Processor #2 15:1 APIC version 16
[ 0.000000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
[ 0.000000] Processor #3 15:1 APIC version 16
[ 0.000000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
[ 0.000000] I/O APIC #4 Version 17 at 0xFEC00000.
[ 0.000000] I/O APIC #5 Version 17 at 0xFD200000.
[ 0.000000] I/O APIC #6 Version 17 at 0xFD201000.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Processors: 1
[ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:40000000)
[ 0.000000] Checking aperture...
[ 0.000000] CPU 0: aperture @ f8000000 size 64 MB
[ 0.000000] CPU 1: aperture @ f8000000 size 64 MB
[ 0.000000] Built 1 zonelists
[ 0.000000] Kernel command line: ro root=/dev/md3 console=tty0 console=ttyS0,115200n8
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 131072 bytes)
[ 0.000000] time.c: Using 1.193182 MHz PIT timer.
[ 0.000000] time.c: Detected 1992.086 MHz processor.
[ 13.476890] time.c: Using PIT/TSC based timekeeping.
[ 13.477331] Console: colour dummy device 80x25
[ 13.697387] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 13.712991] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 13.789909] Memory: 4101416k/5242880k available (1620k kernel code, 92332k reserved, 997k data, 136k init)
[ 13.819815] Security Framework v1.0.0 initialized
[ 13.824992] SELinux: Disabled at boot.
[ 13.829226] Mount-cache hash table entries: 256
[ 13.834275] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 13.842538] CPU: L2 Cache: 1024K (64 bytes/line)
[ 13.847866] CPU: stepping 02
[ 13.851414] checking if image is initramfs... it is
[ 14.188550] Using IO-APIC 4
[ 14.191771] Using IO-APIC 5
[ 14.194987] Using IO-APIC 6
[ 14.208302] Using local APIC timer interrupts.
[ 14.263629] Detected 12.450 MHz APIC timer.
[ 14.268446] testing NMI watchdog ... OK.
[ 14.282975] NET: Registered protocol family 16
[ 14.288476] PCI: Using configuration type 1
[ 14.293313] mtrr: v2.0 (20020519)
[ 14.297419] ACPI: Subsystem revision 20050729
[ 14.302456] ACPI: Interpreter disabled.
[ 14.306890] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 14.313412] pnp: PnP ACPI: disabled
[ 14.317485] usbcore: registered new driver usbfs
[ 14.322838] usbcore: registered new driver hub
[ 14.328010] PCI: Probing PCI hardware
[ 14.332261] PCI: Probing PCI hardware (bus 00)
[ 14.338761] PCI: Discovered primary peer bus 01 [IRQ]
[ 14.344593] PCI: Using IRQ router default [1022/7468] at 0000:01:04.0
[ 14.352035] PCI->APIC IRQ transform: 0000:01:04.2[D] -> IRQ 19
[ 14.358802] PCI->APIC IRQ transform: 0000:02:09.0[A] -> IRQ 24
[ 14.365533] PCI->APIC IRQ transform: 0000:02:09.1[B] -> IRQ 25
[ 14.372248] PCI->APIC IRQ transform: 0000:04:00.0[D] -> IRQ 19
[ 14.379040] PCI->APIC IRQ transform: 0000:04:00.1[D] -> IRQ 19
[ 14.385808] PCI->APIC IRQ transform: 0000:04:05.0[A] -> IRQ 17
[ 14.392539] PCI->APIC IRQ transform: 0000:04:06.0[A] -> IRQ 18
[ 14.399347] PCI-DMA: Disabling AGP.
[ 14.403460] PCI-DMA: aperture base @ f8000000 size 65536 KB
[ 14.409947] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 14.417699] IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
[ 14.426219] audit: initializing netlink socket (disabled)
[ 14.432466] audit: initialized
[ 14.436078] VFS: Disk quotas dquot_6.5.1
[ 14.440654] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 14.448113] devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
[ 14.455261] devfs: boot_options: 0x0
[ 14.459445] Initializing Cryptographic API
[ 14.464203] PCI: MSI quirk detected. pci_msi_quirk set.
[ 14.470274] PCI: MSI quirk detected. pci_msi_quirk set.
[ 14.490389] Linux agpgart interface v0.101 (c) Dave Jones
[ 14.496711] PNP: No PS/2 controller found. Probing ports directly.
[ 14.505346] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 14.511273] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 14.516994] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[ 14.526203] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 14.533322] io scheduler noop registered
[ 14.537861] io scheduler anticipatory registered
[ 14.543217] io scheduler deadline registered
[ 14.548185] io scheduler cfq registered
[ 14.552892] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 14.561690] NET: Registered protocol family 2
[ 14.576640] IP: routing cache hash table of 65536 buckets, 512Kbytes
[ 14.584455] TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
[ 14.596145] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 14.604232] TCP: Hash tables configured (established 524288 bind 65536)
[ 14.611945] NET: Registered protocol family 8
[ 14.616960] NET: Registered protocol family 20
[ 14.622278] Freeing unused kernel memory: 136k freed
Loading, please wait...
Begin: Loading modules ...
[ 14.645287] input: AT Translated Set 2 keyboard on isa0060/serio0
[ 14.657083] Capability LSM initialized
[ 14.669870] NET: Registered protocol family 1
[ 14.686443] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 14.693755] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 14.707909] AMD8111: IDE controller at PCI slot 0000:01:04.1
[ 14.714477] AMD8111: chipset revision 3
[ 14.718933] AMD8111: not 100% native mode: will probe irqs later
[ 14.725869] AMD8111: 0000:01:04.1 (rev 03) UDMA133 controller
[ 14.732469] ide0: BM-DMA at 0x2420-0x2427, BIOS settings: hda:pio, hdb:pio
[ 14.740909] ide1: BM-DMA at 0x2428-0x242f, BIOS settings: hdc:pio, hdd:pio
[ 15.881489] hdd: CD-224E, ATAPI CD/DVD-ROM drive
[ 15.937874] ide1 at 0x170-0x177,0x376 on irq 15
[ 18.513088] hdd: ATAPI 24X CD-ROM drive, 128kB Cache
[ 18.518889] Uniform CD-ROM driver Revision: 3.20
[ 18.772153] tg3.c:v3.31 (June 8, 2005)
[ 18.780608] eth0: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:30:a5:24
[ 18.794116] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[0]
[ 18.803789] eth0: dma_rwctrl[769f4000]
[ 18.818576] eth1: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:30:a5:25
[ 18.832075] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
[ 18.841730] eth1: dma_rwctrl[769f4000]
[ 18.854427] ohci_hcd 0000:04:00.0: Advanced Micro Devices [AMD] AMD-8111 USB
[ 18.862741] ohci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 1
[ 18.871275] ohci_hcd 0000:04:00.0: irq 19, io mem 0xfd000000
[ 18.930659] hub 1-0:1.0: USB hub found
[ 18.935018] hub 1-0:1.0: 3 ports detected
[ 18.942617] ohci_hcd 0000:04:00.1: Advanced Micro Devices [AMD] AMD-8111 USB (#2)
[ 18.951303] ohci_hcd 0000:04:00.1: new USB bus registered, assigned bus number 2
[ 18.959848] ohci_hcd 0000:04:00.1: irq 19, io mem 0xfd001000
[ 19.018622] hub 2-0:1.0: USB hub found
[ 19.022997] hub 2-0:1.0: 3 ports detected
[ 19.040635] SCSI subsystem initialized
[ 19.047043] ata1: SATA max UDMA/100 cmd 0xFFFFC20000014080 ctl 0xFFFFC2000001408A bmdma 0xFFFFC20000014000 irq 17
[ 19.058983] ata2: SATA max UDMA/100 cmd 0xFFFFC200000140C0 ctl 0xFFFFC200000140CA bmdma 0xFFFFC20000014008 irq 17
[ 19.070913] ata3: SATA max UDMA/100 cmd 0xFFFFC20000014280 ctl 0xFFFFC2000001428A bmdma 0xFFFFC20000014200 irq 17
[ 19.082807] ata4: SATA max UDMA/100 cmd 0xFFFFC200000142C0 ctl 0xFFFFC200000142CA bmdma 0xFFFFC20000014208 irq 17
[ 19.449906] ata1: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
[ 19.458221] ata1: dev 0 configured for UDMA/100
[ 19.463445] scsi0 : sata_sil
[ 19.821814] ata2: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
[ 19.830068] ata2: dev 0 configured for UDMA/100
[ 19.835281] scsi1 : sata_sil
[ 20.193734] ata3: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
[ 20.202017] ata3: dev 0 configured for UDMA/100
[ 20.207255] scsi2 : sata_sil
[ 20.565656] ata4: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
[ 20.573948] ata4: dev 0 configured for UDMA/100
[ 20.579205] scsi3 : sata_sil
[ 20.582618] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
[ 20.589939] Type: Direct-Access ANSI SCSI revision: 05
[ 20.598797] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
[ 20.606107] Type: Direct-Access ANSI SCSI revision: 05
[ 20.614984] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
[ 20.622302] Type: Direct-Access ANSI SCSI revision: 05
[ 20.631150] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
[ 20.638484] Type: Direct-Access ANSI SCSI revision: 05
[ 22.664450] SCSI device sda: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.672077] SCSI device sda: drive cache: write back
[ 22.677847] SCSI device sda: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.685509] SCSI device sda: drive cache: write back
[ 22.691291] /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4
[ 22.706480] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[ 22.713735] SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.721369] SCSI device sdb: drive cache: write back
[ 22.727153] SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.734791] SCSI device sdb: drive cache: write back
[ 22.740529] /dev/scsi/host1/bus0/target0/lun0: p1 p2 p3 p4
[ 22.758728] Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
[ 22.765981] SCSI device sdc: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.773675] SCSI device sdc: drive cache: write back
[ 22.779461] SCSI device sdc: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.787123] SCSI device sdc: drive cache: write back
[ 22.792871] /dev/scsi/host2/bus0/target0/lun0: p1 p2 p3 p4
[ 22.812560] Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
[ 22.819822] SCSI device sdd: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.827507] SCSI device sdd: drive cache: write back
[ 22.833316] SCSI device sdd: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.841024] SCSI device sdd: drive cache: write back
[ 22.846788] /dev/scsi/host3/bus0/target0/lun0: p1 p2 p3 p4
[ 22.867064] Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
Done.
Begin: Initializing /dev ...
Done.
Begin: Running /scripts/init-premount ...
FATAL: Error inserting fan (/lib/modules/2.6.12-9-amd64-generic/kernel/drivers/acpi/fan.ko): No such device
FATAL: Error inserting thermal (/lib/modules/2.6.12-9-amd64-generic/kernel/drivers/acpi/thermal.ko): No such device
Done.
Begin: Mounting root file system ...
Begin: Running /scripts/local-top ...
[ 23.224330] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 23.233979] md: raid1 personality registered as nr 3
[ 23.249716] raid5: automatically using best checksumming function: generic_sse
[ 23.262592] generic_sse: 6044.000 MB/sec
[ 23.267530] raid5: using function: generic_sse (6044.000 MB/sec)
[ 23.275210] md: raid5 personality registered as nr 4
[ 23.601260] devfs_mk_dev: could not append to parent for md/0
[ 23.609757] md: md0 stopped.
[ 23.614044] md: bind<sdb1>
[ 23.617323] md: bind<sdc1>
[ 23.620564] md: bind<sdd1>
[ 23.623805] md: bind<sda1>
[ 23.626995] raid1: raid set md0 active with 4 out of 4 mirrors
mdadm: /dev/md0 has been started with 4 drives.
[ 23.641055] devfs_mk_dev: could not append to parent for md/1
[ 23.649588] md: md1 stopped.
[ 23.653883] md: bind<sdb2>
[ 23.657143] md: bind<sdc2>
[ 23.660419] md: bind<sdd2>
[ 23.663659] md: bind<sda2>
[ 23.666829] raid5: device sda2 operational as raid disk 0
[ 23.673104] raid5: device sdd2 operational as raid disk 3
[ 23.679316] raid5: device sdc2 operational as raid disk 2
[ 23.685598] raid5: device sdb2 operational as raid disk 1
[ 23.692275] raid5: allocated 4270kB for md1
[ 23.697098] raid5: raid level 5 set md1 active with 4 out of 4 devices, algorithm 2
[ 23.705958] RAID5 conf printout:
[ 23.709709] --- rd:4 wd:4 fd:0
[ 23.713348] disk 0, o:1, dev:sda2
[ 23.717272] disk 1, o:1, dev:sdb2
[ 23.721214] disk 2, o:1, dev:sdc2
[ 23.725140] disk 3, o:1, dev:sdd2
mdadm: /dev/md1 has been started with 4 drives.
[ 23.740660] devfs_mk_dev: could not append to parent for md/2
[ 23.749195] md: md2 stopped.
[ 23.753499] md: bind<sdb3>
[ 23.756782] md: bind<sdc3>
[ 23.760050] md: bind<sdd3>
[ 23.763323] md: bind<sda3>
[ 23.766489] raid5: device sda3 operational as raid disk 0
[ 23.772723] raid5: device sdd3 operational as raid disk 3
[ 23.778971] raid5: device sdc3 operational as raid disk 2
[ 23.785209] raid5: device sdb3 operational as raid disk 1
[ 23.791895] raid5: allocated 4270kB for md2
[ 23.796733] raid5: raid level 5 set md2 active with 4 out of 4 devices, algorithm 2
[ 23.805597] RAID5 conf printout:
[ 23.809358] --- rd:4 wd:4 fd:0
[ 23.812987] disk 0, o:1, dev:sda3
[ 23.816945] disk 1, o:1, dev:sdb3
[ 23.820871] disk 2, o:1, dev:sdc3
[ 23.824795] disk 3, o:1, dev:sdd3
mdadm: /dev/md2 has been started with 4 drives.
[ 23.844303] devfs_mk_dev: could not append to parent for md/3
[ 23.852907] md: md3 stopped.
[ 23.857209] md: bind<sdb4>
[ 23.860491] md: bind<sdc4>
[ 23.863751] md: bind<sdd4>
[ 23.867023] md: bind<sda4>
[ 23.870187] md: md3: raid array is not clean -- starting background reconstruction
[ 23.878970] raid5: device sda4 operational as raid disk 0
[ 23.885236] raid5: device sdd4 operational as raid disk 3
[ 23.891492] raid5: device sdc4 operational as raid disk 2
[ 23.897764] raid5: device sdb4 operational as raid disk 1
[ 23.904458] raid5: allocated 4270kB for md3
[ 23.909322] raid5: raid level 5 set md3 active with 4 out of 4 devices, algorithm 2
[ 23.918195] RAID5 conf printout:
[ 23.921952] --- rd:4 wd:4 fd:0
[ 23.925610] disk 0, o:1, dev:sda4
[ 23.929560] disk 1, o:1, dev:sdb4
[ 23.933493] disk 2, o:1, dev:sdc4
[ 23.937443] disk 3, o:1, dev:sdd4
[ 23.941428] ....<6>md: syncing RAID array md3
[ 23.946502] md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc.
[ 23.954669] md: using maximum available idle IO bandwith (but not more than 200000 KB/sec) for reconstruction.
[ 23.966246] md: using 128k window, over a total of 67657664 blocks.
mdadm: /dev/md3 has been started with 4 drives.
Done.
Begin: Running /scripts/local-premount ...
[ 24.000782] Attempting manual resume
[ 24.006995] swsusp: Suspend partition has wrong signature?
Done.
[ 24.115879] kjournald starting. Commit interval 5 seconds
[ 24.122230] EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
Done.
* version 2.86 booting
* Starting RAID devices... [ ok ]
* Starting hardware event daemon... [ ok ]
* Creating initial device nodes...
LinuxBIOS-1.1.8_s2881_Fallback Thu Dec 15 18:45:48 EST 2005 starting...
(0,1) link=00
(1,0) link=00
02 nodes initialized.
core0: --- { APICID = 02 NODEID = 01 COREID = 00} ---
SBLink=02
NC node|link=02
More information about the coreboot
mailing list