[LinuxBIOS] GA-6BXC - cont'd
Uwe Hermann
uwe at hermann-uwe.de
Sat Aug 12 23:26:06 CEST 2006
Hi,
On Fri, Aug 11, 2006 at 01:32:45PM -0500, Richard Smith wrote:
> Um.... You need to go re-read all the thread postings on the i44bx and
> V2. Its not even close to running a payload.
>
> Thats it. Thats all the code base does right now is dump out the RAM
> spd. Thats the tip of the iceberg.
>
> Next we have to actually make the RAM work.
> Then we load and jump to linux bios.
> Then we discover and config all the necessary devices on the pci bus
> Then we can try to load a payload.
>
> The next step is to copy the RAM init code from the Intel e7501
> nortbridge (raminit.c) over whats in the i440bx directory. Then start
> comparing that code to what V1 does in 440bx/raminit.inc and fix it up
> so it works.
>
> The e7501 is a DDR controller but a lot of the terminology is the same
> as the SDRAM controller in the 440bx and the structure of the file is
> sane and very well commented.
> It also has some stuff in there about ECC ram which we would
> eventually like to support.
OK, sounds like a lot of work... As I'm not an expert with all this
low-level stuff it'll take a while until I read and understand all the
code and datasheets...
In the mean time, here's a patch which forks the bitworks/ims code and
adds a gigabyte/ga-6bxc target with some minor changes...
Cheers, Uwe.
--
Uwe Hermann
http://www.hermann-uwe.de
http://www.it-services-uh.de | http://www.crazy-hacks.org
http://www.holsham-traders.de | http://www.unmaintained-free-software.org
-------------- next part --------------
Index: src/mainboard/gigabyte/ga-6bxc/Config.lb
===================================================================
--- src/mainboard/gigabyte/ga-6bxc/Config.lb (Revision 0)
+++ src/mainboard/gigabyte/ga-6bxc/Config.lb (Revision 0)
@@ -0,0 +1,136 @@
+##
+## Compute the location and size of where this firmware image
+## (linuxBIOS plus bootloader) will live in the boot rom chip.
+##
+if USE_FALLBACK_IMAGE
+ default ROM_SECTION_SIZE = FALLBACK_SIZE
+ default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
+else
+ default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE )
+ default ROM_SECTION_OFFSET = 0
+end
+
+##
+## Compute the start location and size size of
+## The linuxBIOS bootloader.
+##
+default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+
+##
+## Compute where this copy of linuxBIOS will start in the boot rom
+##
+default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up linuxBIOS,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+default XIP_ROM_SIZE=65536
+default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+
+##
+## Set all of the defaults for an x86 architecture
+##
+
+arch i386 end
+
+##
+## Build the objects we have code for in this directory.
+##
+
+driver mainboard.o
+
+#if HAVE_PIRQ_TABLE object irq_tables.o end
+#object reset.o
+
+##
+## Romcc output
+##
+makerule ./failover.E
+ depends "$(MAINBOARD)/failover.c ./romcc"
+ action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+end
+
+makerule ./failover.inc
+ depends "$(MAINBOARD)/failover.c ./romcc"
+ action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+end
+
+makerule ./auto.E
+ depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ action "./romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+makerule ./auto.inc
+ depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ action "./romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+
+##
+## Build our 16 bit and 32 bit linuxBIOS entry code
+##
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
+
+##
+## Build our reset vector (This is where linuxBIOS is entered)
+##
+if USE_FALLBACK_IMAGE
+ mainboardinit cpu/x86/16bit/reset16.inc
+ ldscript /cpu/x86/16bit/reset16.lds
+else
+ mainboardinit cpu/x86/32bit/reset32.inc
+ ldscript /cpu/x86/32bit/reset32.lds
+end
+
+### Should this be in the northbridge code?
+mainboardinit arch/i386/lib/cpu_reset.inc
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+
+###
+### This is the early phase of linuxBIOS startup
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+if USE_FALLBACK_IMAGE
+ ldscript /arch/i386/lib/failover.lds
+ mainboardinit ./failover.inc
+end
+
+###
+### O.k. We aren't just an intermediary anymore!
+###
+
+##
+## Setup RAM
+##
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+mainboardinit cpu/x86/mmx/enable_mmx.inc
+mainboardinit ./auto.inc
+mainboardinit cpu/x86/mmx/disable_mmx.inc
+
+##
+## Include the secondary Configuration files
+##
+dir /pc80
+config chip.h
+
+chip northbridge/intel/i440bx
+ device pci_domain 0 on
+ end
+
+ chip cpu/intel/socket_PGA370
+ end
+
+end
+
Index: src/mainboard/gigabyte/ga-6bxc/reset.c
===================================================================
--- src/mainboard/gigabyte/ga-6bxc/reset.c (Revision 0)
+++ src/mainboard/gigabyte/ga-6bxc/reset.c (Revision 0)
@@ -0,0 +1,43 @@
+#if 0
+//#include "arch/romcc_io.h"
+#include <arch/io.h>
+
+typedef unsigned device_t;
+
+#define PCI_DEV(BUS, DEV, FN) ( \
+ (((BUS) & 0xFF) << 16) | \
+ (((DEV) & 0x1f) << 11) | \
+ (((FN) & 0x7) << 8))
+
+static void pci_write_config8(device_t dev, unsigned where, unsigned char value)
+{
+ unsigned addr;
+ addr = dev | where;
+ outl(0x80000000 | (addr & ~3), 0xCF8);
+ outb(value, 0xCFC + (addr & 3));
+}
+
+static void pci_write_config32(device_t dev, unsigned where, unsigned value)
+{
+ unsigned addr;
+ addr = dev | where;
+ outl(0x80000000 | (addr & ~3), 0xCF8);
+ outl(value, 0xCFC);
+}
+
+static unsigned pci_read_config32(device_t dev, unsigned where)
+{
+ unsigned addr;
+ addr = dev | where;
+ outl(0x80000000 | (addr & ~3), 0xCF8);
+ return inl(0xCFC);
+}
+
+#include "../../../northbridge/amd/amdk8/reset_test.c"
+
+void hard_reset(void)
+{
+ set_bios_reset();
+ pci_write_config8(PCI_DEV(1, 0x04, 0), 0x47, 1);
+}
+#endif
Index: src/mainboard/gigabyte/ga-6bxc/irq_tables.c
===================================================================
--- src/mainboard/gigabyte/ga-6bxc/irq_tables.c (Revision 0)
+++ src/mainboard/gigabyte/ga-6bxc/irq_tables.c (Revision 0)
@@ -0,0 +1,32 @@
+/* This file was generated by getpir.c, do not modify!
+ (but if you do, please run checkpir on it to verify)
+ Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up
+
+ Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+
+#include <arch/pirq_routing.h>
+
+const struct irq_routing_table intel_irq_routing_table = {
+ PIRQ_SIGNATURE, /* u32 signature */
+ PIRQ_VERSION, /* u16 version */
+ 32+16*5, /* there can be total 5 devices on the bus */
+ 0, /* Where the interrupt router lies (bus) */
+ 0x88, /* Where the interrupt router lies (dev) */
+ 0x1c20, /* IRQs devoted exclusively to PCI usage */
+ 0x1106, /* Vendor */
+ 0x8231, /* Device */
+ 0, /* Crap (miniport) */
+ { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+ 0x5e, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+ {
+ /* 8231 ethernet */
+ {0,0x90, {{0x1, 0xdeb8}, {0x2, 0xdeb8}, {0x3, 0xdeb8}, {0x4, 0xdeb8}}, 0x1, 0},
+ /* 8231 internal */
+ {0,0x88, {{0x2, 0xdeb8}, {0x3, 0xdeb8}, {0x4, 0xdeb8}, {0x1, 0xdeb8}}, 0x2, 0},
+ /* PCI slot */
+ {0,0xa0, {{0x3, 0xdeb8}, {0x4, 0xdeb8}, {0x1, 0xdeb8}, {0x2, 0xdeb8}}, 0, 0},
+ {0,0x50, {{0x4, 0xdeb8}, {0x3, 0xdeb8}, {0x2, 0xdeb8}, {0x1, 0xdeb8}}, 0x3, 0},
+ {0,0x98, {{0x4, 0xdeb8}, {0x3, 0xdeb8}, {0x2, 0xdeb8}, {0x1, 0xdeb8}}, 0x4, 0},
+ }
+};
Index: src/mainboard/gigabyte/ga-6bxc/Options.lb
===================================================================
--- src/mainboard/gigabyte/ga-6bxc/Options.lb (Revision 0)
+++ src/mainboard/gigabyte/ga-6bxc/Options.lb (Revision 0)
@@ -0,0 +1,156 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses HAVE_OPTION_TABLE
+uses USE_OPTION_TABLE
+uses CONFIG_ROM_STREAM
+uses IRQ_SLOT_COUNT
+uses MAINBOARD
+uses MAINBOARD_VENDOR
+uses MAINBOARD_PART_NUMBER
+uses LINUXBIOS_EXTRA_VERSION
+uses ARCH
+uses FALLBACK_SIZE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM_START
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses _RAMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses HAVE_MP_TABLE
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses OBJCOPY
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_CONSOLE_SERIAL8250
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses CONFIG_UDELAY_TSC
+
+## ROM_SIZE is the size of boot ROM that this board will use.
+default ROM_SIZE = 512*1024
+
+###
+### Build options
+###
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## no MP table
+##
+default HAVE_MP_TABLE=0
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=0
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=0
+default IRQ_SLOT_COUNT=4
+#object irq_tables.o
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=0
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 65536
+default FALLBACK_SIZE = 131072
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default USE_OPTION_TABLE = 0
+
+default _RAMBASE = 0x00004000
+
+default CONFIG_ROM_STREAM = 1
+
+##
+## The default compiler
+##
+default CROSS_COMPILE=""
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG 1 system is unusable
+## ALERT 2 action must be taken immediately
+## CRIT 3 critical conditions
+## ERR 4 error conditions
+## WARNING 5 warning conditions
+## NOTICE 6 normal but significant condition
+## INFO 7 informational
+## DEBUG 8 debug-level messages
+## SPEW 9 Way too many details
+
+## Request this level of debugging output
+default DEFAULT_CONSOLE_LOGLEVEL=9
+## At a maximum only compile in this level of debugging
+default MAXIMUM_CONSOLE_LOGLEVEL=9
+
+default CONFIG_UDELAY_TSC=1
+
+end
+
Index: src/mainboard/gigabyte/ga-6bxc/debug.c
===================================================================
--- src/mainboard/gigabyte/ga-6bxc/debug.c (Revision 0)
+++ src/mainboard/gigabyte/ga-6bxc/debug.c (Revision 0)
@@ -0,0 +1,66 @@
+
+static void print_debug_pci_dev(unsigned dev)
+{
+ print_debug("PCI: ");
+ print_debug_hex8((dev >> 16) & 0xff);
+ print_debug_char(':');
+ print_debug_hex8((dev >> 11) & 0x1f);
+ print_debug_char('.');
+ print_debug_hex8((dev >> 8) & 7);
+}
+
+static void print_pci_devices(void)
+{
+ device_t dev;
+ for(dev = PCI_DEV(0, 0, 0);
+ dev <= PCI_DEV(0, 0x1f, 0x7);
+ dev += PCI_DEV(0,0,1)) {
+ uint32_t id;
+ id = pci_read_config32(dev, PCI_VENDOR_ID);
+ if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+ (((id >> 16) & 0xffff) == 0xffff) ||
+ (((id >> 16) & 0xffff) == 0x0000)) {
+ continue;
+ }
+ print_debug_pci_dev(dev);
+ print_debug("\r\n");
+ }
+}
+
+static void dump_pci_device(unsigned dev)
+{
+ int i;
+ print_debug_pci_dev(dev);
+ print_debug("\r\n");
+
+ for(i = 0; i <= 255; i++) {
+ unsigned char val;
+ if ((i & 0x0f) == 0) {
+ print_debug_hex8(i);
+ print_debug_char(':');
+ }
+ val = pci_read_config8(dev, i);
+ print_debug_char(' ');
+ print_debug_hex8(val);
+ if ((i & 0x0f) == 0x0f) {
+ print_debug("\r\n");
+ }
+ }
+}
+
+static void dump_pci_devices(void)
+{
+ device_t dev;
+ for(dev = PCI_DEV(0, 0, 0);
+ dev <= PCI_DEV(0, 0x1f, 0x7);
+ dev += PCI_DEV(0,0,1)) {
+ uint32_t id;
+ id = pci_read_config32(dev, PCI_VENDOR_ID);
+ if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+ (((id >> 16) & 0xffff) == 0xffff) ||
+ (((id >> 16) & 0xffff) == 0x0000)) {
+ continue;
+ }
+ dump_pci_device(dev);
+ }
+}
Index: src/mainboard/gigabyte/ga-6bxc/failover.c
===================================================================
--- src/mainboard/gigabyte/ga-6bxc/failover.c (Revision 0)
+++ src/mainboard/gigabyte/ga-6bxc/failover.c (Revision 0)
@@ -0,0 +1,32 @@
+#define ASSEMBLY 1
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include "arch/romcc_io.h"
+#include "pc80/mc146818rtc_early.c"
+
+static unsigned long main(unsigned long bist)
+{
+ /* This is the primary cpu how should I boot? */
+ if (do_normal_boot()) {
+ goto normal_image;
+ }
+ else {
+ goto fallback_image;
+ }
+ normal_image:
+ asm volatile ("jmp __normal_image"
+ : /* outputs */
+ : "a" (bist) /* inputs */
+ : /* clobbers */
+ );
+ cpu_reset:
+ asm volatile ("jmp __cpu_reset"
+ : /* outputs */
+ : "a"(bist) /* inputs */
+ : /* clobbers */
+ );
+ fallback_image:
+ return bist;
+}
Index: src/mainboard/gigabyte/ga-6bxc/auto.c
===================================================================
--- src/mainboard/gigabyte/ga-6bxc/auto.c (Revision 0)
+++ src/mainboard/gigabyte/ga-6bxc/auto.c (Revision 0)
@@ -0,0 +1,162 @@
+#define ASSEMBLY 1
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/hlt.h>
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "southbridge/intel/i82371eb/i82371eb_early_smbus.c"
+#include "superio/ite/it8671f/it8671f_early_serial.c"
+#include "northbridge/intel/i440bx/raminit.h"
+#include "cpu/x86/mtrr/earlymtrr.c"
+#include "cpu/x86/bist.h"
+
+#define SERIAL_DEV PNP_DEV(0x2e, IT8671F_SP1)
+
+/*
+ */
+void udelay(int usecs)
+{
+ int i;
+ for(i = 0; i < usecs; i++)
+ outb(i&0xff, 0x80);
+}
+
+#include "debug.c"
+#include "lib/delay.c"
+
+
+static void memreset_setup(void)
+{
+}
+
+/*
+ static void memreset(int controllers, const struct mem_controller *ctrl)
+ {
+ }
+*/
+
+
+static void enable_mainboard_devices(void)
+{
+ device_t dev;
+ /* dev 0 for southbridge */
+
+ dev = pci_locate_device(PCI_ID(0x1106,0x8231), 0);
+
+ if (dev == PCI_DEV_INVALID) {
+ die("Southbridge not found!!!\n");
+ }
+ pci_write_config8(dev, 0x50, 7);
+ pci_write_config8(dev, 0x51, 0xff);
+#if 0
+ // This early setup switches IDE into compatibility mode before PCI gets
+ // // a chance to assign I/Os
+ // movl $CONFIG_ADDR(0, 0x89, 0x42), %eax
+ // // movb $0x09, %dl
+ // movb $0x00, %dl
+ // PCI_WRITE_CONFIG_BYTE
+ //
+#endif
+ /* we do this here as in V2, we can not yet do raw operations
+ * to pci!
+ */
+ dev += 0x100; /* ICKY */
+
+ pci_write_config8(dev, 0x42, 0);
+}
+
+static void enable_shadow_ram(void)
+{
+ device_t dev = 0; /* no need to look up 0:0.0 */
+ unsigned char shadowreg;
+ /* dev 0 for southbridge */
+ shadowreg = pci_read_config8(dev, 0x63);
+ /* 0xf0000-0xfffff */
+ shadowreg |= 0x30;
+ pci_write_config8(dev, 0x63, shadowreg);
+}
+
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+ int c;
+ c = smbus_read_byte(device, address);
+ return c;
+}
+
+
+#include "northbridge/intel/i440bx/raminit.c"
+#include "northbridge/intel/i440bx/debug.c"
+#include "sdram/generic_sdram.c"
+
+static void main(unsigned long bist)
+{
+ static const struct mem_controller cpu[] = {
+ {
+ .channel0 = {
+ (0xa << 3) | 0,
+ (0xa << 3) | 1,
+ (0xa << 3) | 2,
+ (0xa << 3) | 3,
+ },
+ }
+ };
+ unsigned long x;
+ int result;
+
+ if (bist == 0) {
+ early_mtrr_init();
+ }
+ it8671f_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ uart_init();
+ console_init();
+
+ /* Halt if there was a built in self test failure */
+ report_bist_failure(bist);
+
+ enable_smbus();
+/*
+ result = spd_read_byte(cpu[0].channel0[0],0x03);
+ print_debug("Result: ");
+ print_debug_hex16(result);
+ print_debug("\r\n");
+*/
+ dump_spd_registers(&cpu[0]);
+
+#if 0
+ enable_shadow_ram();
+ /*
+ memreset_setup();
+ this is way more generic than we need.
+ sdram_initialize(sizeof(cpu)/sizeof(cpu[0]), cpu);
+ */
+ sdram_set_registers((const struct mem_controller *) 0);
+ sdram_set_spd_registers((const struct mem_controller *) 0);
+ sdram_enable(0, (const struct mem_controller *) 0);
+#endif
+
+ /* Check all of memory */
+#if 0
+ ram_check(0x00000000, msr.lo);
+#endif
+#if 0
+ static const struct {
+ unsigned long lo, hi;
+ } check_addrs[] = {
+ /* Check 16MB of memory @ 0*/
+ { 0x00000000, 0x01000000 },
+#if TOTAL_CPUS > 1
+ /* Check 16MB of memory @ 2GB */
+ { 0x80000000, 0x81000000 },
+#endif
+ };
+ int i;
+ for(i = 0; i < sizeof(check_addrs)/sizeof(check_addrs[0]); i++) {
+ ram_check(check_addrs[i].lo, check_addrs[i].hi);
+ }
+#endif
+}
Index: src/mainboard/gigabyte/ga-6bxc/chip.h
===================================================================
--- src/mainboard/gigabyte/ga-6bxc/chip.h (Revision 0)
+++ src/mainboard/gigabyte/ga-6bxc/chip.h (Revision 0)
@@ -0,0 +1,5 @@
+extern struct chip_operations mainboard_gigabyte_ga_6bxc_ops;
+
+struct mainboard_gigabyte_ga_6bxc_config {
+ int nothing;
+};
Index: src/mainboard/gigabyte/ga-6bxc/cmos.layout
===================================================================
--- src/mainboard/gigabyte/ga-6bxc/cmos.layout (Revision 0)
+++ src/mainboard/gigabyte/ga-6bxc/cmos.layout (Revision 0)
@@ -0,0 +1,74 @@
+entries
+
+#start-bit length config config-ID name
+#0 8 r 0 seconds
+#8 8 r 0 alarm_seconds
+#16 8 r 0 minutes
+#24 8 r 0 alarm_minutes
+#32 8 r 0 hours
+#40 8 r 0 alarm_hours
+#48 8 r 0 day_of_week
+#56 8 r 0 day_of_month
+#64 8 r 0 month
+#72 8 r 0 year
+#80 4 r 0 rate_select
+#84 3 r 0 REF_Clock
+#87 1 r 0 UIP
+#88 1 r 0 auto_switch_DST
+#89 1 r 0 24_hour_mode
+#90 1 r 0 binary_values_enable
+#91 1 r 0 square-wave_out_enable
+#92 1 r 0 update_finished_enable
+#93 1 r 0 alarm_interrupt_enable
+#94 1 r 0 periodic_interrupt_enable
+#95 1 r 0 disable_clock_updates
+#96 288 r 0 temporary_filler
+0 384 r 0 reserved_memory
+384 1 e 4 boot_option
+385 1 e 4 last_boot
+386 1 e 1 ECC_memory
+388 4 r 0 reboot_bits
+392 3 e 5 baud_rate
+400 1 e 1 power_on_after_fail
+412 4 e 6 debug_level
+416 4 e 7 boot_first
+420 4 e 7 boot_second
+424 4 e 7 boot_third
+428 4 h 0 boot_index
+432 8 h 0 boot_countdown
+1008 16 h 0 check_sum
+
+enumerations
+
+#ID value text
+1 0 Disable
+1 1 Enable
+2 0 Enable
+2 1 Disable
+4 0 Fallback
+4 1 Normal
+5 0 115200
+5 1 57600
+5 2 38400
+5 3 19200
+5 4 9600
+5 5 4800
+5 6 2400
+5 7 1200
+6 6 Notice
+6 7 Info
+6 8 Debug
+6 9 Spew
+7 0 Network
+7 1 HDD
+7 2 Floppy
+7 8 Fallback_Network
+7 9 Fallback_HDD
+7 10 Fallback_Floppy
+#7 3 ROM
+
+checksums
+
+checksum 392 1007 1008
+
+
Index: src/mainboard/gigabyte/ga-6bxc/mainboard.c
===================================================================
--- src/mainboard/gigabyte/ga-6bxc/mainboard.c (Revision 0)
+++ src/mainboard/gigabyte/ga-6bxc/mainboard.c (Revision 0)
@@ -0,0 +1,12 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <arch/io.h>
+#include "chip.h"
+
+struct chip_operations mainboard_gigabyte_ga_6bxc_ops = {
+ CHIP_NAME("Gigabyte GA-6BXC mainboard ")
+};
+
Index: targets/gigabyte/ga-6bxc/Config.lb
===================================================================
--- targets/gigabyte/ga-6bxc/Config.lb (Revision 0)
+++ targets/gigabyte/ga-6bxc/Config.lb (Revision 0)
@@ -0,0 +1,29 @@
+# Config file for the Gigabyte GA-6BXC board
+# This will make a target directory of ./ga-6bxc
+
+target ga-6bxc
+mainboard gigabyte/ga-6bxc
+
+option ROM_SIZE=262144
+
+romimage "normal"
+ option USE_FALLBACK_IMAGE=0
+ option ROM_IMAGE_SIZE=0x10000
+ option LINUXBIOS_EXTRA_VERSION=".0Normal"
+# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
+# payload ../../../../tg3--ide_disk.zelf
+# payload ../../../../../lnxieepro100.ebi
+ payload /etc/hosts
+end
+
+romimage "fallback"
+ option USE_FALLBACK_IMAGE=1
+ option ROM_IMAGE_SIZE=0x10000
+ option LINUXBIOS_EXTRA_VERSION=".0Fallback"
+# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
+# payload ../../../../tg3--ide_disk.zelf
+# payload ../../../../../lnxieepro100.ebia
+ payload /etc/hosts
+end
+
+buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback"
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 189 bytes
Desc: Digital signature
URL: <http://www.coreboot.org/pipermail/coreboot/attachments/20060812/1343319e/attachment.sig>
More information about the coreboot
mailing list