[LinuxBIOS] New guy in LinuxBios
Vincente Tsou
vincentetsou at nexcom.com.tw
Mon Jun 19 09:44:06 CEST 2006
Hello,
Finally my linuxbios bring up the target board.
capture5.txt is booting log.
But most of device on the target board are not work.
Such as BCM5704 under PCI-X bridge.
If I try to load "tg3" module into the kernel, I got error message like
this,
[root at linuxbios ~]# modprobe tg3
PCI: No IRQ known for interrupt pin A of device 0000:03:04.0. Please try
using pci=biosirq.
PCI: No IRQ known for interrupt pin B of device 0000:03:04.1. Please try
using pci=biosirq.
How to assign an IRQ for each device ??
2006/5/12, Stefan Reinauer <stepan at coresystems.de>:
>
> * Vincente Tsou <vincentetsou at nexcom.com.tw> [060512 06:22]:
> > Dear Lu and Stefan,
> >
> > Thank you very much for your reply.
> >
> > But I can't find the inherent_ht.c in my LinuxBios source tree.
>
> Yinghai is talking about src/northbridge/amd/amdk8/incoherent_ht.c
>
> You need to try commenting out the lines I sent in the last mail from
> src/northbridge/amd/amdk8/resourcemap.c
>
> Stefan
>
> --
> coresystems GmbH • Brahmsstr. 16 • D-79104 Freiburg i. Br.
> Tel.: +49 761 7668825 • Fax: +49 761 7664613
> Email: info at coresystems.de • http://www.coresystems.de/
>
>
--
Best Regards,
Vincente Tsou
Engineer
R/D, S/W Dept.
NEXCOM International Co.
Tel: 886-2-82280606 Ext. 3205
Fax: 886-2-82280506
E-mail: vincentetsou at nexcom.com.tw
Web: http://www.nexcom.com.tw/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.coreboot.org/pipermail/coreboot/attachments/20060619/8f0ec83e/attachment.html>
-------------- next part --------------
LinuxBIOS-1.1.8h412_Fallback Mon Jun 19 15:02:16 CST 2006 starting...
01 nodes initialized.
SBLink=01
NC node|link=01
ht reset -
LinuxBIOS-1.1.8h412_Fallback Mon Jun 19 15:02:16 CST 2006 starting...
01 nodes initialized.
SBLink=01
NC node|link=01
Ram1.00
Ram2.00
Ram3
Initializing memory: done
Ram4
v_esp=000cfd54
testx = 5a5a5a5a
Copying data from cache to ram -- switching to use ram as stack... Done
testx = 5a5a5a5a
Disabling cache as ram now
Clearing initial memory region: Done
Copying LinuxBIOS to ram.
src=fffe0000
dst=00004000
linxbios_ram.bin length = 0001746c
Jumping to LinuxBIOS.
LinuxBIOS-1.1.8h412_Fallback Mon Jun 19 15:02:16 CST 2006 booting...
Enumerating buses...
PCI_DOMAIN: 0000 enabled
APIC_CLUSTER: 0 enabled
PCI: pci_scan_bus for bus 0
PCI: 00:18.0 [1022/1100] enabled
PCI: 00:18.1 [1022/1101] enabled
PCI: 00:18.2 [1022/1102] enabled
PCI: 00:18.3 [1022/1103] enabled
Disabling static device: PCI: 00:19.0
Disabling static device: PCI: 00:19.1
Disabling static device: PCI: 00:19.2
Disabling static device: PCI: 00:19.3
PCI: 01:00.0 [1022/7450] enabled
PCI: 01:01.0 [1022/7450] enabled next_unitid: 0003
PCI: 01:00.0 [1022/7460] enabled
PCI: 01:03.0 [1022/7460] enabled next_unitid: 0007
PCI: pci_scan_bus for bus 1
PCI: 01:01.0 [1022/7450] enabled
PCI: 01:01.1 [1022/7451] enabled
PCI: 01:02.0 [1022/7450] enabled
PCI: 01:02.1 [1022/7451] enabled
PCI: 01:03.0 [1022/7460] enabled
PCI: 01:04.0 [1022/7468] enabled
PCI: 01:04.1 [1022/7469] enabled
PCI: 01:04.2 [1022/746a] enabled
PCI: 01:04.3 [1022/746b] enabled
PCI: pci_scan_bus for bus 2
PCI: pci_scan_bus returning with max=02
PCI: 02: Conventional PCI
PCI: pci_scan_bus for bus 3
PCI: 03:04.0 [14e4/16a8] enabled
PCI: 03:04.1 [14e4/16a8] enabled
PCI: pci_scan_bus returning with max=03
PCI: 03: 133MHz PCI-X
PCI: pci_scan_bus for bus 4
PCI: 04:00.0 [1022/7464] enabled
PCI: 04:00.1 [1022/7464] enabled
USB2 disabled.
PCI: 04:00.2 [1022/7463] disabled
PCI: 04:02.0 [1002/4752] enabled
PCI: 04:04.0 [8086/1229] enabled
PCI: pci_scan_bus returning with max=04
PNP: 002e.0 disabled
PNP: 002e.1 disabled
PNP: 002e.2 enabled
PNP: 002e.3 enabled
PNP: 002e.5 enabled
PNP: 002e.6 disabled
PNP: 002e.7 disabled
PNP: 002e.8 disabled
PNP: 002e.9 disabled
PNP: 002e.a disabled
PNP: 002e.b enabled
PCI: pci_scan_bus returning with max=04
PCI: pci_scan_bus returning with max=04
PCI: 00:18.3 siblings=0
CPU: APIC: 00 enabled
done
Allocating resources...
Reading resources...
PCI: 01:02.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 3 io
PCI: 01:02.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 3 prefmem
PCI: 01:03.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 4 prefmem
Done reading resources.
Setting resources...
PCI: 00:18.0 1a1 <- [0x00fd300000 - 0x00fd2fffff] prefmem <node 0 link 1>
PCI: 00:18.0 1a9 <- [0x00fc000000 - 0x00fd2fffff] mem <node 0 link 1>
PCI: 00:18.0 1d9 <- [0x0000001000 - 0x0000002fff] io <node 0 link 1>
PCI: 01:01.1 10 <- [0x00fd200000 - 0x00fd200fff] mem64
PCI: 01:02.0 20 <- [0x00fd100000 - 0x00fd1fffff] bus 3 mem
PCI: 03:04.0 10 <- [0x00fd100000 - 0x00fd10ffff] mem64
PCI: 03:04.0 18 <- [0x00fd110000 - 0x00fd11ffff] mem64
PCI: 03:04.1 10 <- [0x00fd120000 - 0x00fd12ffff] mem64
PCI: 03:04.1 18 <- [0x00fd130000 - 0x00fd13ffff] mem64
PCI: 01:02.1 10 <- [0x00fd201000 - 0x00fd201fff] mem64
PCI: 01:03.0 1c <- [0x0000001000 - 0x0000001fff] bus 4 io
PCI: 01:03.0 20 <- [0x00fc000000 - 0x00fd0fffff] bus 4 mem
PCI: 04:00.0 10 <- [0x00fd050000 - 0x00fd050fff] mem
PCI: 04:00.1 10 <- [0x00fd051000 - 0x00fd051fff] mem
PCI: 04:02.0 10 <- [0x00fc000000 - 0x00fcffffff] mem
PCI: 04:02.0 14 <- [0x0000001000 - 0x00000010ff] io
PCI: 04:02.0 18 <- [0x00fd052000 - 0x00fd052fff] mem
PCI: 04:02.0 30 <- [0x00fd000000 - 0x00fd01ffff] romem
PCI: 04:04.0 10 <- [0x00fd053000 - 0x00fd053fff] mem
PCI: 04:04.0 14 <- [0x0000001400 - 0x000000143f] io
PCI: 04:04.0 18 <- [0x00fd020000 - 0x00fd03ffff] mem
PCI: 04:04.0 30 <- [0x00fd040000 - 0x00fd04ffff] romem
PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] io
PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] irq
PNP: 002e.3 60 <- [0x00000002f8 - 0x00000002ff] io
PNP: 002e.3 70 <- [0x0000000003 - 0x0000000003] irq
PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io
PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io
PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq
PNP: 002e.5 72 <- [0x000000000c - 0x000000000c] irq
PNP: 002e.b 60 <- [0x0000000290 - 0x0000000297] io
PNP: 002e.b 70 <- [0x0000000005 - 0x0000000005] irq
PCI: 01:04.1 20 <- [0x0000002420 - 0x000000242f] io
PCI: 01:04.2 10 <- [0x0000002400 - 0x000000241f] io
PCI: 01:04.3 58 <- [0x0000002000 - 0x00000020ff] io
PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart>
Done setting resources.
Done allocating resources.
Enabling resources...
PCI: 00:18.0 cmd <- 140
PCI: 01:01.1 subsystem <- 00/00
PCI: 01:01.1 cmd <- 146
PCI: 01:02.0 bridge ctrl <- 0003
PCI: 01:02.0 cmd <- 146
PCI: 03:04.0 subsystem <- 00/00
PCI: 03:04.0 cmd <- 142
PCI: 03:04.1 subsystem <- 00/00
PCI: 03:04.1 cmd <- 142
PCI: 01:02.1 subsystem <- 00/00
PCI: 01:02.1 cmd <- 146
PCI: 01:03.0 bridge ctrl <- 0003
PCI: 01:03.0 cmd <- 147
PCI: 04:00.0 subsystem <- 00/00
PCI: 04:00.0 cmd <- 142
PCI: 04:00.1 subsystem <- 00/00
PCI: 04:00.1 cmd <- 142
PCI: 04:02.0 cmd <- 1c3
PCI: 04:04.0 cmd <- 143
PCI: 01:04.0 subsystem <- 00/00
PCI: 01:04.0 cmd <- 14f
w83627hf hwm smbus enabled
PCI: 01:04.1 subsystem <- 00/00
PCI: 01:04.1 cmd <- 141
PCI: 01:04.2 subsystem <- 00/00
PCI: 01:04.2 cmd <- 141
PCI: 01:04.3 subsystem <- 00/00
PCI: 01:04.3 cmd <- 141
PCI: 00:18.1 subsystem <- 00/00
PCI: 00:18.1 cmd <- 140
PCI: 00:18.2 subsystem <- 00/00
PCI: 00:18.2 cmd <- 140
PCI: 00:18.3 cmd <- 140
done.
Initializing devices...
Root Device init
PCI: 00:18.0 init
PCI: 01:02.0 init
PCI: 03:04.0 init
PCI: 03:04.1 init
PCI: 01:03.0 init
PCI: 01:04.0 init
amd8111: ioapic bsp_apicid = 00
RTC Init
Invalid CMOS LB checksum
enabling HPET @0xfed00000
PNP: 002e.2 init
PNP: 002e.3 init
PNP: 002e.5 init
PNP: 002e.b init
PCI: 01:04.1 init
IDE1 IDE0 PCI: 01:04.3 init
set power on after power fail
PCI: 00:18.1 init
PCI: 00:18.2 init
PCI: 00:18.3 init
NB: Function 3 Misc Control.. done.
APIC_CLUSTER: 0 init
Initializing CPU #0
CPU: vendor AMD device f5a
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 512MB, type WB
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
microcode: equivalent processor rev id = 0x004a, patch id = 0x00000000
microcode: patch id that want to apply= 0x00000047
microcode: updated to patch id = 0x00000047 success
Setting up local apic... apic_id: 0 done.
Clearing memory 2048K - 524288K: ------- done
CPU #0 Initialized
APIC delivery error (4).
CPU 1 would not start!
CPU 1 did not initialize!
All AP CPUs stopped
PCI: 04:02.0 init
PCI: 04:04.0 init
Devices initialized
Writing IRQ routing tables to 0xf0000...done.
Wrote the mp table end at: 00000020 - 000001b8
Moving GDT to 0x500...ok
Wrote linuxbios table at: 00000530 - 00000dcc checksum a17
Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3
rom_stream: 0xfffc0000 - 0xfffdffff
Found ELF candiate at offset 0
Loading Etherboot version: 5.2.6
Dropping non PT_LOAD segment
New segment addr 0x20000 size 0x6469a offset 0xb0 filesize 0xd0cd
(cleaned up) New segment addr 0x20000 size 0x6469a offset 0xb0 filesize 0xd0cd
Loading Segment: addr: 0x000000001ffa4000 memsz: 0x0000000000020000 filesz: 0x000000000000d0cd
Clearing Segment: addr: 0x000000001ffb10cd memsz: 0x0000000000012f33
Loading Segment: addr: 0x0000000000040000 memsz: 0x000000000004469a filesz: 0x0000000000000000
Clearing Segment: addr: 0x0000000000040000 memsz: 0x000000000004469a
Jumping to boot code at 0x20000
ROM segment 0x0000 length 0x0000 reloc 0x00020000
CPU 2281 Mhz
Etherboot 5.2.6 (GPL) http://etherboot.org Tagged ELF for [TG3][FILO]
Relocating _text from: [0002d0d0,00086240) to [1fea6e90,1ff00000)
Boot from (N)etwork (D)isk or (Q)uit? D
Probing pci disk...
[FILO]FILO version 0.4.1 (vincente at TSOU) Wed May 3 15:16:34 CST 2006
Press <Enter> for default boot, or <Esc> for boot prompt... 2 1 timed out
boot: hda1:/boot/vmlinuz initrd=/boot/initrd noacpi ro root=/dev/hda1 console=tty0 console=ttyS0,115200
hda: LBA: Maxtor 6Y080P0
Mounted ext2fs
Found Linux version 2.6.9-1.667 (bhcompile at tweety.build.redhat.com) #1 Tue Nov 2 14:41:25 EST 2004 bzImage.
Loading kernel... ok
Loading initrd... ok
Jumping to entry point...
Linux version 2.6.9-1.667 (bhcompile at tweety.build.redhat.com) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 Tue Nov 2 14:41:25 EST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000000e34 type 16
BIOS-e820: 0000000000000e34 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 00000000000f0400 type 16
BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
0MB HIGHMEM available.
512MB LOWMEM available.
zapping low mappings.
DMI not present.
ACPI: Unable to locate RSDP
Built 1 zonelists
Kernel command line: noacpi ro root=/dev/hda1 console=tty0 console=ttyS0,115200
mapped 4G/4G trampoline to ffff4000.
Initializing CPU#0
CPU 0 irqstacks, hard=023d5000 soft=023d4000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2205.406 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 515148k/524288k available (2068k kernel code, 8584k reserved, 647k data, 144k init, 0k highmem)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD 02/05 stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 386k freed
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Unable to handle 64-bit address space for
PCI: Discovered primary peer bus 01 [IRQ]
PCI: Using IRQ router default [1022/7468] at 0000:01:04.0
PCI: IRQ 0 for device 0000:01:04.2 doesn't match PIRQ mask - try pci=usepirqmask
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1009857017.468:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 6ECDA687281A73E5
- key was been created 89567280 seconds in future
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: probe of vesafb0 failed with error -6
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ÿttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD8111: IDE controller at PCI slot 0000:01:04.1
AMD8111: chipset revision 3
AMD8111: not 100% native mode: will probe irqs later
AMD8111: 0000:01:04.1 (rev 03) UDMA133 controller
ide0: BM-DMA at 0x2420-0x2427, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x2428-0x242f, BIOS settings: hdc:pio, hdd:pio
hda: Maxtor 6Y080P0, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(133)
hda:hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
ide0: reset: success
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
ide0: reset: success
hda1 hda2 hda3
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 32Kbytes
TCP: Hash tables configured (established 131072 bind 37449)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 144k freed
Red Hat nash version 4.1.18 starting
Mounted /proc filesystem
Mounting sysfs
Creating /dev
Starting udev
Loading jbd.ko module
Loading ext3.ko module
Creating root device
Mounting root filesystem
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Switching to new root
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
INIT: version 2.85 booting
Welcome to Fedora Core
Press 'I' to enter interactive startup.
Starting udev: [ OK ]
Initializing hardware... storage network audio done[ OK ]
Configuring kernel parameters: [ OK ]
Setting clock (utc): Tue Jan 1 11:50:35 CST 2002 [ OK ]
Setting hostname linuxbios: [ OK ]
Checking root filesystem
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/hda1
/1: clean, 333623/1026144 files, 1822094/2048279 blocks
[ OK ]
Remounting root filesystem in read-write mode: [ OK ]
Setting up Logical Volume Management: [ OK ]
Checking filesystems
Checking all file systems.
[/sbin/fsck.ext3 (1) -- /home] fsck.ext3 -a /dev/hda3
/home1: clean, 32800/8863744 files, 531251/17697605 blocks
[ OK ]
Mounting local filesystems: [ OK ]
Enabling local filesystem quotas: [ OK ]
Enabling swap space: [ OK ]
INIT: Entering runlevel: 3
Entering non-interactive startup
Starting sysstat: [ OK ]
Checking for new hardware [ OK ]
Applying iptables firewall rules: [ OK ]
Starting pcmcia: [ OK ]
Setting network parameters: [ OK ]
Bringing up loopback interface: [ OK ]
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Starting irqbalance: [ OK ]
Starting portmap: [ OK ]
Starting NFS statd: [ OK ]
Starting NFS4 idmapd: [ OK ]
Mounting other filesystems: [ OK ]
Starting lm_sensors: [ OK ]
Starting automount:No Mountpoints Defined[ OK ]
Starting nifd...
Starting mDNSResponder... [ OK ]
Starting smartd: [ OK ]
Starting hpoj: [ OK ]
Starting cups: [ OK ]
Starting sshd:[ OK ]
Starting xinetd: [ OK ]
Starting sendmail: make: Warning: File `Makefile' has modification time 8.4e+07 s in the future
make: warning: Clock skew detected. Your build may be incomplete.
/usr/sbin/sendmail: /usr/sbin/sendmail: cannot execute binary file
[FAILED]
Starting sm-client: /usr/sbin/sendmail: /usr/sbin/sendmail: cannot execute binary file
[FAILED]
Starting console mouse services: [ OK ]
Starting IIIMF input server: [ OK ]
Starting Canna server: [ OK ]
Starting crond: [ OK ]
Starting xfs: [ OK ]
Starting anacron: [ OK ]
Starting atd: [ OK ]
Starting system message bus: [ OK ]
Starting cups-config-daemon: [ OK ]
Starting HAL daemon: [ OK ]
Fedora Core release 3 (Heidelberg)
Kernel 2.6.9-1.667 on an i686
linuxbios login:
More information about the coreboot
mailing list