[LinuxBIOS] DK8-HTX FILO IDE timeout

[yhlu]

let me build one image tomorrow.

YH

On 9/21/06, Chris Stillo <cstillo at comcast.net> wrote:
> YH,
>
> Thanks for the suggestion. I decreased LOG level to 8, and did not see
> "IDE1 IDE0 PCI: 00:07.1 init" in the LOG. Then I hacked amd8111_ide.c
> now I see "IDE1 IDE0 PCI: *01:04.3* init" in the log. And still the IDE
> timeout happens in FILO... but this is not suprising since it looks like
> the wrong PCI address is assigned to IDE(?) If so, do you know how to
> correct this?
>
> Thanks,
> Chris
> > Please decrease that LOG level to 8.
> >
> > And you should got
> > PCI:00:07.1 init
> > IDE1
> > IDE0
> >
> > in your log output.
> >
> > If it still doesn't work, hardcode amd8111_ide.c to enable ide device
> > directly.
> >
> > YH
> >
> > -----Original Message-----
> > From: Chris Stillo [mailto:cstillo at comcast.net]
> > Sent: Thursday, September 21, 2006 3:57 PM
> > To: Lu, Yinghai
> > Cc: linuxbios at linuxbios.org; Stefan Reinauer
> > Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
> >
> > I added these lines and recompiled, but it still does not work. Maybe
> > there is still something else missing? I will re-check PCI configuration
> >
> > in MB's Config.lb, must still be an error in there...
> >
> >> Check serengeti_leopard or tyan/s2881 etc  MB Config.lb to add two
> >>
> > lines
> >
> >> to enable your IDE devices.
> >>
> >> YH
> >>
> >> -----Original Message-----
> >> From: Chris Stillo [mailto:cstillo at comcast.net]
> >> Sent: Thursday, September 21, 2006 3:24 PM
> >> To: Lu, Yinghai
> >> Cc: linuxbios at linuxbios.org; Stefan Reinauer
> >> Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
> >>
> >> No, those lines are not there in MB Config... I serach for 'ide0' and
> >> find nothing... where exactly do they go in the file?
> >>
> >>
> >>> Please check if you have register "ide0_enable"="1"  in MB Config.lb
> >>>
> >>>                 chip southbridge/amd/amd8111
> >>>                     # this "device pci 0.0" is the parent the next
> >>>
> > one
> >
> >>>                     # PCI bridge
> >>>                     device pci 0.0 on
> >>>                         device pci 0.0 on end
> >>>                         device pci 0.1 on end
> >>>                         device pci 0.2 on end
> >>>                         device pci 1.0 off end
> >>>                     end
> >>> .....
> >>>                     register "ide0_enable"="1"
> >>>                     register "ide1_enable"="1"
> >>>
> >>> ....
> >>>
> >>>
> >>> YH
> >>>
> >>>
> >>> -----Original Message-----
> >>> From: Chris Stillo [mailto:cstillo at comcast.net]
> >>> Sent: Thursday, September 21, 2006 3:13 PM
> >>> To: Lu, Yinghai
> >>> Cc: linuxbios at linuxbios.org; Stefan Reinauer
> >>> Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
> >>>
> >>> Hi YH,
> >>>
> >>> I checked  MB Config.lb as you suggested. From lspci I know my IDE
> >>> controller is here:
> >>>
> >>> 00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev
> >>> 03)
> >>>
> >>> Yet I do not see 00:07.1 mentioned in the MB Config.lb in the
> >>> southbridge section. Maybe this is the issue... , maybe IDE is not
> >>> configured since SATA would be mostly used? (My SATA drive is
> >>> recognized, but has XP on it :| -- it is presenlty disconnected).
> >>>
> >>> I also included AMD 3111 chip.h below, which looks ok. I have not
> >>> modified either file at all.
> >>> If you see an error please let me know...
> >>>
> >>> Thanks,
> >>> Chris
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>> Check your MB Config.lb to see if amd8111 is under correct 0.18.0
> >>>>
> >>>>
> >>>>
> >>> link.
> >>>
> >>>
> >>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>> # config for Iwill/DK8HTX
> >>> chip northbridge/amd/amdk8/root_complex
> >>>     device pci_domain 0 on
> >>>         chip northbridge/amd/amdk8
> >>>             device pci 18.0 on # LDT 0
> >>>                 chip southbridge/amd/amd8131
> >>>                     device pci 0.0 on end
> >>>                     device pci 0.1 on end
> >>>                     device pci 1.0 on end
> >>>                     device pci 1.1 on end
> >>>                 end
> >>>                 chip southbridge/amd/amd8111
> >>>                     # this "device pci 0.0" is the parent the next
> >>>
> > one
> >
> >>>                     # PCI bridge
> >>>                     device pci 0.0 on
> >>>                         device pci 0.0 on end
> >>>                         device pci 0.1 on end
> >>>                         device pci 0.2 on end
> >>>                         device pci 1.0 off end
> >>>                     end
> >>>
> >>>
> >>>
> > ------------------------------------------------------------------------
> >
> >>
> >>
> >>> -------------------------------
> >>>
> >>> /LinuxBIOSv2/src/southbridge/amd/amd8111
> >>> bash-3.1$ more chip.h
> >>>
> >>> #ifndef AMD8111_CHIP_H
> >>> #define AMD8111_CHIP_H
> >>>
> >>> struct southbridge_amd_amd8111_config
> >>> {
> >>>         unsigned int ide0_enable : 1;
> >>>         unsigned int ide1_enable : 1;
> >>>         unsigned int phy_lowreset : 1;
> >>> };
> >>>
> >>> struct chip_operations;
> >>> extern struct chip_operations southbridge_amd_amd8111_ops;
> >>>
> >>> #endif /* AMD8111_CHIP_H */
> >>>
> >>>
> >>>
> >>>
> >>>> YH
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >
> >
> >
> >
> >
> >
> >
> >
>
>
>
> --
> linuxbios mailing list
> linuxbios at linuxbios.org
> http://www.openbios.org/mailman/listinfo/linuxbios
>