[LinuxBIOS] r2641 - in trunk/LinuxBIOSv2: src/mainboard src/mainboard/asi src/mainboard/asi/mb_5blmp targets targets/asi targets/asi/mb_5blmp

svn at openbios.org svn at openbios.org
Wed May 9 09:52:14 CEST 2007


Author: uwe
Date: 2007-05-09 09:52:14 +0200 (Wed, 09 May 2007)
New Revision: 2641

Added:
   trunk/LinuxBIOSv2/src/mainboard/asi/
   trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/
   trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/Config.lb
   trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/Options.lb
   trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/auto.c
   trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/chip.h
   trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/irq_tables.c
   trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/mainboard.c
   trunk/LinuxBIOSv2/targets/asi/
   trunk/LinuxBIOSv2/targets/asi/mb_5blmp/
   trunk/LinuxBIOSv2/targets/asi/mb_5blmp/Config.lb
Log:
Add initial support for the ASI/BCom MB-5BLMP mainboard, as used in
the IGEL Winnet III thin client.

It boots a Linux kernel, but there are some problems. The login
prompt is never reached, it simply hangs at some point.
One possible reason is the IRQ table, which needs fixing.

Signed-off-by: Uwe Hermann <uwe at hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan at coresystems.de>



Added: trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/Config.lb	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/Config.lb	2007-05-09 07:52:14 UTC (rev 2641)
@@ -0,0 +1,209 @@
+##
+## Compute the location and size of where this firmware image
+## (linuxBIOS plus bootloader) will live in the boot rom chip.
+##
+if USE_FALLBACK_IMAGE
+	default ROM_SECTION_SIZE   = FALLBACK_SIZE
+	default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
+else
+	default ROM_SECTION_SIZE   = ( ROM_SIZE - FALLBACK_SIZE )
+	default ROM_SECTION_OFFSET = 0
+end
+
+##
+## Compute the start location and size size of
+## The linuxBIOS bootloader.
+##
+default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default PAYLOAD_SIZE            = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+
+##
+## Compute where this copy of linuxBIOS will start in the boot rom
+##
+default _ROMBASE      = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up linuxBIOS,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+default XIP_ROM_SIZE=65536
+default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+
+##
+## Set all of the defaults for an x86 architecture
+##
+
+arch i386 end
+
+##
+## Build the objects we have code for in this directory.
+##
+
+driver mainboard.o
+
+if HAVE_PIRQ_TABLE
+	object irq_tables.o
+end
+
+##
+## Romcc output
+##
+# makerule ./failover.E
+# 	depends "$(MAINBOARD)/failover.c ./romcc" 
+# 	action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+# end
+# 
+# makerule ./failover.inc
+# 	depends "$(MAINBOARD)/failover.c ./romcc"
+# 	action "./romcc    -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+# end
+
+makerule ./auto.E 
+	depends	"$(MAINBOARD)/auto.c ./romcc" 
+	action	"./romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+makerule ./auto.inc 
+	depends "$(MAINBOARD)/auto.c ./romcc"
+	action	"./romcc    -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+
+##
+## Build our 16 bit and 32 bit linuxBIOS entry code
+##
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
+
+##
+## Build our reset vector (This is where linuxBIOS is entered)
+##
+if USE_FALLBACK_IMAGE 
+	mainboardinit cpu/x86/16bit/reset16.inc 
+	ldscript /cpu/x86/16bit/reset16.lds 
+else
+	mainboardinit cpu/x86/32bit/reset32.inc 
+	ldscript /cpu/x86/32bit/reset32.lds 
+end
+
+### Should this be in the northbridge code?
+mainboardinit arch/i386/lib/cpu_reset.inc
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+
+###
+### This is the early phase of linuxBIOS startup 
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+# if USE_FALLBACK_IMAGE
+# 	ldscript /arch/i386/lib/failover.lds 
+# 	mainboardinit ./failover.inc
+# end
+
+###
+### O.k. We aren't just an intermediary anymore!
+###
+
+##
+## Setup RAM
+##
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+mainboardinit cpu/amd/model_gx1/cpu_setup.inc
+mainboardinit cpu/amd/model_gx1/gx_setup.inc
+mainboardinit ./auto.inc
+
+##
+## Include the secondary Configuration files 
+##
+dir /pc80
+config chip.h
+
+chip northbridge/amd/gx1		# Northbridge
+  device pci_domain 0 on
+    device pci 0.0 on end
+      chip southbridge/amd/cs5530	# Southbridge
+        device pci 12.0 on
+          chip superio/nsc/pc87351	# Super I/O
+            device pnp 2e.0 on		# PIC
+               io 0x60 = 0x20
+               io 0x62 = 0xa0
+               irq 0x70 = 2
+            end
+            device pnp 2e.1 on		# DMA
+            end
+            device pnp 2e.2 on		# System Timer
+               io 0x60 = 0x40
+               irq 0x70 = 0
+            end
+            device pnp 2e.3 on		# RTC
+               io 0x60 = 0x70
+               irq 0x70 = 8
+            end
+            device pnp 2e.4 on		# Keyboard + Mouse
+               io 0x60 = 0x60
+               io 0x62 = 0x64
+               irq 0x70 = 1
+               irq 0x72 = 12
+            end
+            device pnp 2e.5 on		# PC Speaker
+            end
+            device pnp 2e.6 on		# Math Coprocessor (FPU)
+               io 0x60 = 0xf0
+               irq 0x70 = 13
+            end
+            device pnp 2e.7 on		# System board
+            end
+            device pnp 2e.8 on		# Motherboard resources
+            end
+            device pnp 2e.9 on		# PCI bus
+            end
+            device pnp 2e.c on		# Motherboard resources
+            end
+            device pnp 2e.d on		# Motherboard resources
+            end
+            device pnp 2e.e on		# COM1
+               io 0x60 = 0x3f8
+               irq 0x70 = 4
+            end
+            device pnp 2e.f off		# FDC
+            end
+            device pnp 2e.10 on		# Parallel port
+               io 0x60 = 0x378
+               irq 0x70 = 7
+            end
+            device pnp 2e.12 on		# COM2
+               io 0x60 = 0x2f8
+               irq 0x70 = 3
+            end
+          end
+        device pci 12.1 off end		# SMI
+        device pci 12.2 on  end		# IDE
+        device pci 12.3 off end 	# Audio
+        device pci 12.4 off end		# Video (VGA)
+      end
+      # device pci 12.4 on		# VGA (onboard)
+      #   chip drivers/pci/onboard
+      #     device pci 12.4 on end
+      #     register "rom_address" = "0xfffc0000" # 256 KB image
+      #     # register "rom_address" = "0xfff80000" # 512 KB image
+      #     # register "rom_address" = "0xfff00000" # 1 MB image
+      #   end
+      # end
+      device pci 0f.0 off end		# Ethernet (Realtek RTL8139B)
+      device pci 13.0 on end		# USB
+    end
+  end
+
+  chip cpu/amd/model_gx1		# CPU
+  end
+
+end
+

Added: trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/Options.lb
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/Options.lb	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/Options.lb	2007-05-09 07:52:14 UTC (rev 2641)
@@ -0,0 +1,160 @@
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses CONFIG_ROM_PAYLOAD
+uses IRQ_SLOT_COUNT
+uses MAINBOARD
+uses MAINBOARD_VENDOR
+uses MAINBOARD_PART_NUMBER
+uses LINUXBIOS_EXTRA_VERSION
+uses ARCH
+uses FALLBACK_SIZE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_PAYLOAD_START
+# uses CONFIG_COMPRESS
+# uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
+# uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses _RAMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses OBJCOPY
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_CONSOLE_SERIAL8250
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses CONFIG_UDELAY_TSC
+uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
+# uses CONFIG_CONSOLE_VGA
+# uses CONFIG_PCI_ROM_RUN
+
+
+## ROM_SIZE is the size of boot ROM that this board will use.
+default ROM_SIZE = 256 * 1024
+
+###
+### Build options
+###
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=0
+
+## Delay timer options
+##
+default CONFIG_UDELAY_TSC=1
+default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=5        # TODO?
+
+##
+## Build code to export a CMOS option table
+##
+# default HAVE_OPTION_TABLE=0
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 64 * 1024
+default FALLBACK_SIZE = 128 * 1024
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+# default USE_OPTION_TABLE = 0
+
+default _RAMBASE = 0x00004000
+
+default CONFIG_ROM_PAYLOAD = 1
+
+##
+## The default compiler
+##
+default CROSS_COMPILE=""
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG      1   system is unusable               
+## ALERT      2   action must be taken immediately 
+## CRIT       3   critical conditions              
+## ERR        4   error conditions                 
+## WARNING    5   warning conditions               
+## NOTICE     6   normal but significant condition 
+## INFO       7   informational                    
+## DEBUG      8   debug-level messages             
+## SPEW       9   Way too many details             
+
+## Request this level of debugging output
+default DEFAULT_CONSOLE_LOGLEVEL=9
+## At a maximum only compile in this level of debugging
+default MAXIMUM_CONSOLE_LOGLEVEL=9
+
+# VGA Console
+# default CONFIG_CONSOLE_VGA=1
+# default CONFIG_PCI_ROM_RUN=1
+
+end
+

Added: trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/auto.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/auto.c	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/auto.c	2007-05-09 07:52:14 UTC (rev 2641)
@@ -0,0 +1,53 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Uwe Hermann <uwe at hermann-uwe.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#define ASSEMBLY 1
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/hlt.h>
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "northbridge/amd/gx1/raminit.c"
+#include "superio/nsc/pc87351/pc87351_early_serial.c"
+#include "cpu/x86/bist.h"
+
+#define SERIAL_DEV PNP_DEV(0x2e, PC87351_SP1)
+
+static void main(unsigned long bist)
+{
+	/* Initialize the serial console. */
+	pc87351_enable_serial(SERIAL_DEV, TTYS0_BASE);
+	uart_init();
+	console_init();
+
+	/* Halt if there was a built in self test failure. */
+	report_bist_failure(bist);
+
+	/* Initialize RAM. */
+	sdram_init();
+
+	/* Check whether RAM works. */
+	/* ram_check(0x00000000, 0x4000); */
+}

Added: trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/chip.h
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/chip.h	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/chip.h	2007-05-09 07:52:14 UTC (rev 2641)
@@ -0,0 +1,25 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Uwe Hermann <uwe at hermann-uwe.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+extern struct chip_operations mainboard_asi_mb_5blmp_ops;
+
+struct mainboard_asi_mb_5blmp_config {
+	int nothing;
+};

Added: trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/irq_tables.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/irq_tables.c	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/irq_tables.c	2007-05-09 07:52:14 UTC (rev 2641)
@@ -0,0 +1,39 @@
+/* TODO: This is currently copied from the IEI NOVA-4899R target, but it's
+ * quite surely wrong for this board. It gets me further in the boot process
+ * than using no irq_tables.c file at all, though!
+ */
+
+/* TODO: Add license header. */
+
+#include <arch/pirq_routing.h>
+
+const struct irq_routing_table intel_irq_routing_table = {
+	PIRQ_SIGNATURE,  /* u32 signature */
+	PIRQ_VERSION,    /* u16 version   */
+	32+16*5,	 /* there can be total 5 devices on the bus */
+	0x00,		 /* Where the interrupt router lies (bus) */
+	(0x12<<3)|0x0,   /* Where the interrupt router lies (dev) */
+	0xe00,		 /* IRQs devoted exclusively to PCI usage */
+	0x1078,		 /* Vendor */
+	0x0002,		 /* Device */
+	0,		 /* Crap (miniport) */
+	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+	0x2d,         /*  u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+	{
+		/* bus,     dev|fn,   {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap},  slot, rfu */
+		// USB
+		{0x00,(0x13<<3)|0x0, {{0x01, 0xdeb8}, {0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x00, 0x0deb8}}, 0x0, 0x0},
+		// eth0
+		{0x00,(0x0a<<3)|0x0, {{0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x04, 0xdeb8}, {0x00, 0x0deb8}}, 0x0, 0x0},//0x3, 0x0},
+		// eth1
+		{0x00,(0x0b<<3)|0x0, {{0x03, 0xdeb8}, {0x04, 0xdeb8}, {0x02, 0xdeb8}, {0x00, 0x0deb8}}, 0x0, 0x0},//0x2, 0x0},
+		// eth2
+		{0x00,(0x0c<<3)|0x0, {{0x04, 0xdeb8}, {0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x00, 0x0deb8}}, 0x0, 0x0},//0x1, 0x0},
+		// PCI slot
+		{0x00,(0x0f<<3)|0x0, {{0x04, 0xdeb8}, {0x03, 0xdeb8}, {0x02, 0xdeb8}, {0x00, 0x0deb8}}, 0x0, 0x0},
+	}
+};
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+        return copy_pirq_routing_table(addr);
+}

Added: trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/mainboard.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/mainboard.c	                        (rev 0)
+++ trunk/LinuxBIOSv2/src/mainboard/asi/mb_5blmp/mainboard.c	2007-05-09 07:52:14 UTC (rev 2641)
@@ -0,0 +1,27 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Uwe Hermann <uwe at hermann-uwe.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#include <device/device.h>
+#include "chip.h"
+
+struct chip_operations mainboard_asi_mb_5blmp_ops = {
+	CHIP_NAME("ASI/BCom MB-5BLMP Mainboard")
+};
+

Added: trunk/LinuxBIOSv2/targets/asi/mb_5blmp/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/targets/asi/mb_5blmp/Config.lb	                        (rev 0)
+++ trunk/LinuxBIOSv2/targets/asi/mb_5blmp/Config.lb	2007-05-09 07:52:14 UTC (rev 2641)
@@ -0,0 +1,43 @@
+##
+## This file is part of the LinuxBIOS project.
+##
+## Copyright (C) 2007 Uwe Hermann <uwe at hermann-uwe.de>
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+##
+
+target mb_5blmp
+mainboard asi/mb_5blmp
+
+option ROM_SIZE = (256 * 1024)
+# option ROM_SIZE = (256 * 1024) - (32 * 1024)
+# option FALLBACK_SIZE = (256 * 1024) - (32 * 1024)
+
+romimage "normal"
+	option USE_FALLBACK_IMAGE = 0
+	option ROM_IMAGE_SIZE = 64 * 1024
+	option LINUXBIOS_EXTRA_VERSION = ".0Normal"
+	payload /tmp/filo.elf
+end
+
+romimage "fallback"
+	option USE_FALLBACK_IMAGE = 1
+	option ROM_IMAGE_SIZE = 64 * 1024
+	option LINUXBIOS_EXTRA_VERSION = ".0Fallback"
+	payload /tmp/filo.elf
+end
+
+buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback"
+# buildrom ./linuxbios.rom ROM_SIZE "fallback"





More information about the coreboot mailing list