[LinuxBIOS] r2702 - trunk/LinuxBIOSv2/src/northbridge/intel/i440bx

[svn at openbios.org]

Author: uwe
Date: 2007-05-28 16:37:06 +0200 (Mon, 28 May 2007)
New Revision: 2702

Modified:
   trunk/LinuxBIOSv2/src/northbridge/intel/i440bx/raminit.c
Log:
Lower the RAM init delays we use on the Intel 440BX.

As per JEDEC, we should wait 200us until voltages and clocks are stable.
Then apply NOPs for 200 clock cycles (for simplicity we use 200us here).

All other delays are so low that we get away with just waiting 1us.

Signed-off-by: Uwe Hermann <uwe at hermann-uwe.de>
Acked-by: Peter Stuge <peter at stuge.se>
Acked-by: Stefan Reinauer <stepan at coresystems.de>



Modified: trunk/LinuxBIOSv2/src/northbridge/intel/i440bx/raminit.c
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/intel/i440bx/raminit.c	2007-05-27 23:31:31 UTC (rev 2701)
+++ trunk/LinuxBIOSv2/src/northbridge/intel/i440bx/raminit.c	2007-05-28 14:37:06 UTC (rev 2702)
@@ -509,44 +509,41 @@
 {
 	int i;
 
-	/* TODO: Use a delay here? Needed? */
-	mdelay(200);
+	/* 0. Wait until power/voltages and clocks are stable (200us). */
+	udelay(200);
 
-	/* TODO: How long should the delays be? Fix later. */
-
-	/* 1. Apply NOP. */
+	/* 1. Apply NOP. Wait 200 clock cycles (200us should do). */
 	PRINT_DEBUG("RAM Enable 1: Apply NOP\r\n");
 	do_ram_command(ctrl, RAM_COMMAND_NOP, 0);
-	mdelay(10);
+	udelay(200);
 
 	/* 2. Precharge all. Wait tRP. */
 	PRINT_DEBUG("RAM Enable 2: Precharge all\r\n");
 	do_ram_command(ctrl, RAM_COMMAND_PRECHARGE, 0);
-	mdelay(10);
+	udelay(1);
 
 	/* 3. Perform 8 refresh cycles. Wait tRC each time. */
 	PRINT_DEBUG("RAM Enable 3: CBR\r\n");
 	for (i = 0; i < 8; i++) {
 		do_ram_command(ctrl, RAM_COMMAND_CBR, 0);
-		mdelay(10);
+		udelay(1);
 	}
 
 	/* 4. Mode register set. Wait two memory cycles. */
 	PRINT_DEBUG("RAM Enable 4: Mode register set\r\n");
 	do_ram_command(ctrl, RAM_COMMAND_MRS, 0x1d0);
-	mdelay(10);
-	mdelay(10);
+	udelay(2);
 
 	/* 5. Normal operation. */
 	PRINT_DEBUG("RAM Enable 5: Normal operation\r\n");
 	do_ram_command(ctrl, RAM_COMMAND_NORMAL, 0);
-	mdelay(10);
+	udelay(1);
 
 	/* 6. Finally enable refresh. */
 	PRINT_DEBUG("RAM Enable 6: Enable refresh\r\n");
 	// pci_write_config8(ctrl->d0, PMCR, 0x10);
 	spd_enable_refresh(ctrl);
-	mdelay(10);
+	udelay(1);
 
 	PRINT_DEBUG("Northbridge following SDRAM init:\r\n");
 	DUMPNORTH();