[LinuxBIOS] Supertek ST-3ET

[Markus Boas]

Hi Volks,
the ST-3WT boots but it dosn't load the rtl8139.elf oder zelf image for pxe.

There is the boot log:

Sep 19:08:00 CEST 2007 starting...
Setting up default parameters for memory
Sizing memory
Probing for DIMM0
    Found DIMM0
    Page Size:       00002000
    Component Banks: 4
    Module Banks:    1
    DIMM size:       08000000
Probing for DIMM1
MC_BANK_CFG = 00701530
Copying LinuxBIOS to RAM.
Jumping to LinuxBIOS.
LinuxBIOS-2.0.0.0Normal So 30. Sep 19:08:00 CEST 2007 booting...
clocks_per_usec: 360
Enumerating buses...
Finding PCI configuration type.
PCI: Using configuration type 1
PCI_DOMAIN: 0000 enabled
PCI: pci_scan_bus for bus 00
PCI: 00:00.0 [1078/0001] enabled
PCI: 00:0f.0 [10ec/8139] enabled
PCI: 00:12.0 [1078/0100] enabled
PCI: 00:12.1 [1078/0101] enabled
PCI: 00:12.2 [1078/0102] enabled
PCI: 00:12.3 [1078/0103] enabled
PCI: 00:12.4 [1078/0104] enabled
PCI: 00:13.0 [0e11/a0f8] enabled
PNP: 002e.0 enabled
PNP: 002e.1 enabled
PNP: 002e.2 enabled
PNP: 002e.3 disabled
PNP: 002e.4 enabled
PNP: 002e.5 enabled
PNP: 002e.6 enabled
PNP: 002e.7 enabled
PNP: 002e.8 enabled
PCI: 00:12.1 disabled
PCI: 00:12.2 enabled
PCI: 00:12.3 disabled
PCI: 00:12.4 disabled
PCI: pci_scan_bus returning with max=000
done
Allocating resources...
Reading resources...
Done reading resources.
Setting resources...
BC_DRAM_TOP = 0x07bfffff
MC_GBASE_ADD = 0x000000f8
I would set ram size to 124 Mbytes
PCI: 00:0f.0 10 <- [0x0000001000 - 0x00000010ff] io
PCI: 00:0f.0 14 <- [0x00febfd000 - 0x00febfd0ff] mem
PCI: 00:12.1 10 <- [0x00febfe000 - 0x00febfe0ff] mem
PCI: 00:12.2 20 <- [0x0000001400 - 0x000000147f] io
PCI: 00:12.3 10 <- [0x00febff000 - 0x00febff07f] mem
PCI: 00:12.4 10 <- [0x00febfb000 - 0x00febfbfff] mem
PCI: 00:13.0 10 <- [0x00febfc000 - 0x00febfcfff] mem
Done setting resources.
Done allocating resources.
Enabling resources...
PCI: 00:00.0 cmd <- 07
PCI: 00:0f.0 cmd <- 03
PCI: 00:12.0 cmd <- 0f
PCI: 00:12.2 missing enable_resources
PCI: 00:12.1 cmd <- 02
PCI: 00:12.2 cmd <- 01
PCI: 00:12.3 cmd <- 02
PCI: 00:12.4 cmd <- 02
PCI: 00:13.0 cmd <- 02
done.
Initializing devices...
Root Device init
PCI: 00:00.0 init
northbridge: northbridge_init()
PCI: 00:12.0 init
PNP: 002e.0 init
PNP: 002e.1 init
PNP: 002e.2 init
PNP: 002e.4 init
PNP: 002e.5 init
PNP: 002e.6 init
PNP: 002e.7 init
PNP: 002e.8 init
PCI: 00:0f.0 init
PCI: 00:12.1 init
PCI: 00:12.2 init
Primary IDE interface disabled
Secondary IDE interface enabled
PCI: 00:12.3 init
PCI: 00:12.4 init
PCI: 00:13.0 init
Devices initialized
Copying IRQ routing tables to 0xf0000...done.
Verifing copy of IRQ routing tables at 0xf0000...done
Checking IRQ routing table consistency...
check_pirq_routing_table() - irq_routing_table located at: 0x000f0000
done.
Moving GDT to 0x500...ok
Adjust low_table_end from 0x00000530 to 0x00001000
Adjust rom_table_end from 0x000f0400 to 0x00100000
Wrote linuxbios table at: 00000530 - 0000068c  checksum 7000

Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3

rom_stream: 0xfffc0000 - 0xfffcffff
No header at 0
...
...
...
No header at 8096
header_offset is -1
Can not load ELF


The Config.lb

# Config file for the Eaglelion 5BCM motherboard
# This will make a target directory of 5bcm

target 5bcm
mainboard eaglelion/5bcm

option ROM_SIZE=512*1024

romimage "normal"
        option USE_FALLBACK_IMAGE=0
        option ROM_IMAGE_SIZE=0x10000
        option LINUXBIOS_EXTRA_VERSION=".0Normal"
#       payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
#       payload ../../../../tg3--ide_disk.zelf
#       payload ../../../../../lnxieepro100.ebi
#       payload /etc/hosts
        payload /home/ryven/hardware/Linuxbios/payload/rtl8139.elf
end

romimage "fallback"
        option USE_FALLBACK_IMAGE=1
        option ROM_IMAGE_SIZE=0x10000
        option LINUXBIOS_EXTRA_VERSION=".0Fallback"
#       payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
#       payload ../../../../tg3--ide_disk.zelf
#       payload ../../../../../lnxieepro100.ebia
#       payload /etc/hosts
        payload /home/ryven/hardware/Linuxbios/payload/rtl8139.elf
end

buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback"

The lspci -vv

Geode:~# lspci -vv
0000:00:00.0 Host bridge: Cyrix Corporation PCI Master
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

0000:00:0f.0 Ethernet controller: Realtek Semiconductor Co., Ltd. 
RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Realtek Semiconductor Co., Ltd. RT8139
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at e000 [size=256]
        Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA 
PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:12.0 ISA bridge: Cyrix Corporation 5530 Legacy [Kahlua] (rev 30)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x04 (16 bytes)

0000:00:12.1 Bridge: Cyrix Corporation 5530 SMI [Kahlua]
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Region 0: Memory at 40012000 (32-bit, non-prefetchable) [size=256]

0000:00:12.2 IDE interface: Cyrix Corporation 5530 IDE [Kahlua] (prog-if 80 
[Master])
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Region 4: I/O ports at f000 [size=16]

0000:00:12.3 Multimedia audio controller: Cyrix Corporation 5530 Audio 
[Kahlua]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Region 0: Memory at 40011000 (32-bit, non-prefetchable) [size=128]

0000:00:12.4 VGA compatible controller: Cyrix Corporation 5530 Video [Kahlua] 
(prog-if 00 [VGA])
        Subsystem: Cyrix Corporation: Unknown device 0001
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Region 0: Memory at 40800000 (32-bit, non-prefetchable) [size=8M]

0000:00:13.0 USB Controller: Compaq Computer Corporation ZFMicro Chipset USB 
(rev 06) (prog-if 10 [OHCI])
        Subsystem: Compaq Computer Corporation ZFMicro Chipset USB
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (20000ns max), Cache Line Size: 0x08 (32 bytes)
        Interrupt: pin A routed to IRQ 15
        Region 0: Memory at d0004000 (32-bit, non-prefetchable) [size=4K]

Can say me somebody what i make wrong?


Greeding
	Markus