[coreboot] lifebook b-2175 working with coreboot?
Countzero786 at gmx.de
Countzero786 at gmx.de
Sun Apr 6 18:35:26 CEST 2008
Greetings,
I'd like to know if there's a chance I can get coreboot to run on an old Fujitsu-Siemens Lifebook B-2175 I own.
As it uses the Intel 440mx chipset, here are links to the (complete I think?) official documentation:
http://www.intel.com/design/chipsets/designex/273504.htm
http://www.intel.com/design/chipsets/specupdt/245051.htm
http://www.intel.com/design/chipsets/datashts/440MX-66DSPub.htm
http://www.intel.com/design/chipsets/embedded/docs/440mx.htm
And the data I got from probing with the tools I found on your site, lspci and dmesg.
Thanks for your time in advance. Said.
./flashrom
--------------------
Calibrating delay loop... OK.
No coreboot table found.
Found chipset "Intel 440MX", enabling flash write... OK.
MBM29F400TC found at physical address 0xfff80000.
Flash part is MBM29F400TC (512 KB).
No operations were specified.
./superiotool -d
--------------------
superiotool r3194
Found SMSC FDC37N769 (id=0x28, rev=0x01) at 0x3f0
Register dump:
idx 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f
val 20 90 00 f4 00 00 ff 00 00 00 40 00 0e 28 01 00 00 00 00 00 02 00 00 03 00 00 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03 00 00
def 28 9c 88 70 00 00 ff 00 00 00 00 00 02 28 NA 00 00 80 RR RR NA NA NA 03 RR RR RR RR RR RR 80 00 3c RR RR 00 00 00 00 00 00 00 RR 00 00 03 00 00
lspci -v -v -v
--------------------
00:00.0 Host bridge: Intel Corporation 82440MX Host Bridge (rev 01)
Subsystem: Fujitsu Limited. Unknown device 107f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
00:00.1 Multimedia audio controller: Intel Corporation 82440MX AC'97 Audio Controller
Subsystem: Fujitsu Limited. QSound_SigmaTel Stac97 PCI Audio
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 9
Region 0: I/O ports at 1000 [size=256]
Region 1: I/O ports at 1400 [size=64]
00:00.2 Modem: Intel Corporation 82440MX AC'97 Modem Controller (prog-if 00 [Generic])
Subsystem: Fujitsu Limited. Unknown device 10d1
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 9
Region 0: I/O ports at 2000 [size=256]
Region 1: I/O ports at 1800 [size=128]
00:07.0 Bridge: Intel Corporation 82440MX ISA Bridge (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:07.1 IDE interface: Intel Corporation 82440MX EIDE Controller (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at 1480 [size=16]
00:07.2 USB Controller: Intel Corporation 82440MX USB Universal Host Controller (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin D routed to IRQ 15
Region 4: I/O ports at 14a0 [size=32]
00:07.3 Bridge: Intel Corporation 82440MX Power Management Controller
Control: I/O+ Mem+ BusMaster- SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:12.0 Ethernet controller: Intel Corporation 82557/8/9 Ethernet Pro 100 (rev 09)
Subsystem: Fujitsu Limited. Unknown device 1070
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fc020000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 1440 [size=64]
Region 2: Memory at fc000000 (32-bit, non-prefetchable) [size=128K]
Capabilities: <access denied>
00:13.0 CardBus bridge: O2 Micro, Inc. OZ6933/711E1 CardBus/SmartCardBus Controller (rev 02)
Subsystem: Fujitsu Limited. Unknown device 10e6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 20020000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 10000000-13fff000 (prefetchable)
Memory window 1: 14000000-17fff000
I/O window 0: 00001c00-00001cff
I/O window 1: 00002800-000028ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:13.1 CardBus bridge: O2 Micro, Inc. OZ6933/711E1 CardBus/SmartCardBus Controller (rev 02)
Subsystem: Fujitsu Limited. Unknown device 10e6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin B routed to IRQ 9
Region 0: Memory at 20021000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 18000000-1bfff000 (prefetchable)
Memory window 1: 1c000000-1ffff000
I/O window 0: 00002c00-00002cff
I/O window 1: 00003000-000030ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:14.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M (rev 64) (prog-if 00 [VGA controller])
Subsystem: Fujitsu Limited. Unknown device 1103
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 2400 [size=256]
Region 2: Memory at fc021000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 20000000 [disabled] [size=128K]
Capabilities: <access denied>
dmesg
--------------------
Linux version 2.6.24-WDC (root at wdc.inc) (gcc version 4.3.0 (GCC) ) #1 Fri Apr 4 09:50:06 CEST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e7800 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007fe0000 (usable)
BIOS-e820: 0000000007fe0000 - 0000000007fefc00 (ACPI data)
BIOS-e820: 0000000007fefc00 - 0000000007ff0000 (ACPI NVS)
BIOS-e820: 0000000007ff0000 - 0000000007ff2000 (reserved)
BIOS-e820: 0000000007ff2000 - 0000000008000000 (usable)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
128MB LOWMEM available.
Entering add_active_range(0, 0, 32768) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 32768
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 32768
On node 0 totalpages: 32768
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 224 pages used for memmap
Normal zone: 28448 pages, LIFO batch:7
Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F64D0, 0014 (r0 FUJ )
ACPI: RSDT 07FEC74F, 0028 (r1 FUJ QUILT 1060000 FUJ 1000)
ACPI: FACP 07FEFB8C, 0074 (r1 FUJ QUILT 1060000 FUJ 1000)
ACPI: DSDT 07FEC777, 3415 (r1 FUJ QUILT 1060000 MSFT 1000007)
ACPI: FACS 07FEFFC0, 0040
ACPI: DMI detected: Fujitsu Siemens
ACPI: PM-Timer IO Port: 0xff08
Allocating PCI resources starting at 10000000 (gap: 08000000:f7f00000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e8000
swsusp: Registered nosave memory region: 00000000000e8000 - 0000000000100000
swsusp: Registered nosave memory region: 0000000007fe0000 - 0000000007fef000
swsusp: Registered nosave memory region: 0000000007fef000 - 0000000007ff0000
swsusp: Registered nosave memory region: 0000000007ff0000 - 0000000007ff2000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: root=/dev/hda3 ro vga=6
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffb000 (01102000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 512 (order: 9, 2048 bytes)
Detected 497.575 MHz processor.
Console: colour VGA+ 80x60
console [tty0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 125144k/131072k available (2200k kernel code, 5316k reserved, 720k data, 284k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffb5000 - 0xfffff000 ( 296 kB)
vmalloc : 0xc8800000 - 0xfffb3000 ( 887 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
.init : 0xc03de000 - 0xc0425000 ( 284 kB)
.data : 0xc03260b7 - 0xc03da39c ( 720 kB)
.text : 0xc0100000 - 0xc03260b7 (2200 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 995.54 BogoMIPS (lpj=497774)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: Intel Celeron (Coppermine) stepping 06
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 0k freed
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
ACPI: setting ELCR to 0200 (from 8200)
net_namespace: 64 bytes
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd9ce, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: GPE = 0x2c, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region ff00-ff3f claimed by PIIX4 ACPI
PCI quirk: region ff80-ff8f claimed by PIIX4 SMB
PIIX4 devres C PIO at fd60-fd67
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 *15)
ACPI: Power Resource [USBP] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 8 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Time: tsc clocksource has been installed.
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0xff00-0xff3f has been reserved
system 00:01: ioport range 0xf800-0xf87f has been reserved
system 00:01: ioport range 0xfd60-0xfd67 has been reserved
system 00:01: ioport range 0xfe00-0xfe00 has been reserved
system 00:01: ioport range 0xff80-0xff8f has been reserved
PCI: Bus 1, cardbus bridge: 0000:00:13.0
IO window: 00001c00-00001cff
IO window: 00002800-000028ff
PREFETCH window: 10000000-13ffffff
MEM window: 14000000-17ffffff
PCI: Bus 5, cardbus bridge: 0000:00:13.1
IO window: 00002c00-00002cff
IO window: 00003000-000030ff
PREFETCH window: 18000000-1bffffff
MEM window: 1c000000-1fffffff
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:13.0 to 64
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
ACPI: PCI Interrupt 0000:00:13.1[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:13.1 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
Unpacking initramfs... done
Freeing initrd memory: 749k freed
IA-32 Microcode Update Driver: v1.14a <tigran at aivazian.fsnet.co.uk>
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered (default)
PCI: Firmware left 0000:00:12.0 e100 interrupts enabled, disabling
Boot video device is 0000:00:14.0
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
PCI: Enabling device 0000:00:00.2 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:00.2[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI interrupt for device 0000:00:00.2 disabled
loop: module loaded
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Using IPI Shortcut mode
Freeing unused kernel memory: 284k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller (0x8086:0x7199 rev 0x00) at PCI slot 0000:00:07.1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1480-0x1487, BIOS settings: hda:DMA, hdb:pio
PIIX4: IDE port disabled
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
hda: TOSHIBA MK1016GAP, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 19640880 sectors (10056 MB), CHS=19485/16/63
hda: cache flushes not supported
hda: hda1 hda2 < hda5 > hda3 hda4
SGI XFS with ACLs, security attributes, realtime, no debug enabled
SGI XFS Quota Management subsystem
Filesystem "hda3": Disabling barriers, not supported by the underlying device
XFS mounting filesystem hda3
Ending clean XFS mount for filesystem: hda3
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k
floppy0: no floppy controllers found
ide-floppy driver 0.99.newide
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [CMB1] (battery absent)
input: Power Button (FF) as /devices/virtual/input/input1
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/virtual/input/input2
ACPI: Power Button (CM) [PWRB]
input: Lid Switch as /devices/virtual/input/input3
ACPI: Lid Switch [LID]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
Marking TSC unstable due to: TSC halts in idle.
Time: acpi_pm clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
PCI: Enabling device 0000:00:07.2 (0000 -> 0001)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 15
PCI: setting IRQ 15 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 15, io base 0x000014a0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
eepro100.c:v1.09j-t 9/29/99 Donald Becker
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw at saw.sw.com.sg> and others
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
eth0: OEM i82557/i82558 10/100 Ethernet, 00:00:0e:21:09:35, IRQ 9.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0xdbd8681d).
input: PC Speaker as /devices/platform/pcspkr/input/input4
input: PS/2 Touchpad as /devices/platform/i8042/serio1/input/input5
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
usb 1-1: new low speed USB device using uhci_hcd and address 2
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Yenta: CardBus bridge found at 0000:00:13.0 [10cf:10e6]
Yenta O2: res at 0x94/0xD4: ea/00
Yenta O2: enabling read prefetch/write burst
usb 1-1: configuration #1 chosen from 1 choice
input: LBPS/2 Fujitsu Lifebook TouchScreen as /devices/platform/i8042/serio1/input/input6
Yenta: ISA IRQ mask 0x0cb8, PCI irq 9
Socket status: 30000006
Yenta: CardBus bridge found at 0000:00:13.1 [10cf:10e6]
Yenta: ISA IRQ mask 0x0cb8, PCI irq 9
Socket status: 30000006
ACPI: PCI Interrupt 0000:00:00.1[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:00.1 to 64
intel8x0_measure_ac97_clock: measured 50106 usecs
intel8x0: clocking to 48000
usbcore: registered new interface driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:07.2/usb1/1-1/1-1:1.0/input/input7
input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:07.2-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Filesystem "hda3": Disabling barriers, not supported by the underlying device
Filesystem "hda3": Disabling barriers, not supported by the underlying device
JFS: nTxBlock = 986, nTxLock = 7895
Filesystem "hda4": Disabling barriers, not supported by the underlying device
XFS mounting filesystem hda4
Ending clean XFS mount for filesystem: hda4
Adding 248968k swap on /dev/hda5. Priority:-1 extents:1 across:248968k
hda: cache flushes not supported
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
spurious 8259A interrupt: IRQ7.
--
GMX startet ShortView.de. Hier findest Du Leute mit Deinen Interessen!
Jetzt dabei sein: http://www.shortview.de/?mc=sv_ext_mf@gmx
More information about the coreboot
mailing list