[coreboot] r3588 - in trunk/coreboot-v2/src: arch/i386/boot config include/boot southbridge/amd southbridge/amd/rs690

svn at coreboot.org svn at coreboot.org
Mon Sep 22 15:07:21 CEST 2008


Author: stepan
Date: 2008-09-22 15:07:20 +0200 (Mon, 22 Sep 2008)
New Revision: 3588

Added:
   trunk/coreboot-v2/src/southbridge/amd/rs690/
   trunk/coreboot-v2/src/southbridge/amd/rs690/Config.lb
   trunk/coreboot-v2/src/southbridge/amd/rs690/chip.h
   trunk/coreboot-v2/src/southbridge/amd/rs690/rs690.c
   trunk/coreboot-v2/src/southbridge/amd/rs690/rs690.h
   trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_cmn.c
   trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_early_setup.c
   trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_gfx.c
   trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_ht.c
   trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_pcie.c
Modified:
   trunk/coreboot-v2/src/arch/i386/boot/coreboot_table.c
   trunk/coreboot-v2/src/config/Options.lb
   trunk/coreboot-v2/src/include/boot/coreboot_tables.h
Log:
Patch for AMD RS690 chipset.

All the PCIe slots are enabled in this patch except power management.

Signed-off-by: Michael Xie <Michael.Xie at amd.com>
Reviewed-by: Marc Jones <marc.jones at amd.com>
Acked-by: Stefan Reinauer <stepan at coresystems.de>



Modified: trunk/coreboot-v2/src/arch/i386/boot/coreboot_table.c
===================================================================
--- trunk/coreboot-v2/src/arch/i386/boot/coreboot_table.c	2008-09-19 22:58:59 UTC (rev 3587)
+++ trunk/coreboot-v2/src/arch/i386/boot/coreboot_table.c	2008-09-22 13:07:20 UTC (rev 3588)
@@ -447,6 +447,15 @@
 	lb_add_memory_range(mem, LB_MEM_TABLE, 
 		rom_table_start, rom_table_end-rom_table_start);
 
+	/* AMD rs690 chip, we should remove the UMA from system memory. */
+#if (CONFIG_GFXUMA == 1) 
+	printk_info("uma_memory_start=0x%x, uma_memory_size=0x%x \n", 
+	uma_memory_start, uma_memory_size);
+	lb_add_memory_range(mem, LB_MEM_TABLE, 
+		uma_memory_start, uma_memory_size);
+#endif
+
+
 	/* Note:
 	 * I assume that there is always memory at immediately after
 	 * the low_table_end.  This means that after I setup the coreboot table.

Modified: trunk/coreboot-v2/src/config/Options.lb
===================================================================
--- trunk/coreboot-v2/src/config/Options.lb	2008-09-19 22:58:59 UTC (rev 3587)
+++ trunk/coreboot-v2/src/config/Options.lb	2008-09-22 13:07:20 UTC (rev 3588)
@@ -1073,12 +1073,24 @@
 	comment "name of the microcode patch file"	
 end
 
+define K8_MEM_BANK_B_ONLY
+	default 0
+	export always
+	comment "use AMD K8's memory bank B only to make a 64bit memory system and memory bank A is free, such as Filbert."
+end
+
 define CONFIG_VIDEO_MB
         default none
         export used
         comment "Integrated graphics with UMA has dynamic setup"
 end
 
+define CONFIG_GFXUMA
+        default none
+        export used
+        comment "GFX UMA"
+end
+
 define CONFIG_SPLASH_GRAPHIC
 	default 0
 	export used

Modified: trunk/coreboot-v2/src/include/boot/coreboot_tables.h
===================================================================
--- trunk/coreboot-v2/src/include/boot/coreboot_tables.h	2008-09-19 22:58:59 UTC (rev 3587)
+++ trunk/coreboot-v2/src/include/boot/coreboot_tables.h	2008-09-22 13:07:20 UTC (rev 3588)
@@ -43,6 +43,12 @@
  * See also: util/lbtdump/lbtdump.c
  */
 
+/* AMD rs690 chip, declare global variables. */
+#if (CONFIG_GFXUMA == 1) 
+	unsigned long uma_memory_start, uma_memory_size;
+#endif
+	
+
 struct lb_uint64 {
 	uint32_t lo;
 	uint32_t hi;

Added: trunk/coreboot-v2/src/southbridge/amd/rs690/Config.lb
===================================================================
--- trunk/coreboot-v2/src/southbridge/amd/rs690/Config.lb	                        (rev 0)
+++ trunk/coreboot-v2/src/southbridge/amd/rs690/Config.lb	2008-09-22 13:07:20 UTC (rev 3588)
@@ -0,0 +1,27 @@
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2008 Advanced Micro Devices, Inc.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; version 2 of the License.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+##
+##
+##
+
+config chip.h
+driver rs690_cmn.o
+driver rs690.o
+driver rs690_pcie.o
+driver rs690_ht.o
+driver rs690_gfx.o

Added: trunk/coreboot-v2/src/southbridge/amd/rs690/chip.h
===================================================================
--- trunk/coreboot-v2/src/southbridge/amd/rs690/chip.h	                        (rev 0)
+++ trunk/coreboot-v2/src/southbridge/amd/rs690/chip.h	2008-09-22 13:07:20 UTC (rev 3588)
@@ -0,0 +1,40 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#ifndef RS690_CHIP_H
+#define RS690_CHIP_H
+
+/* Member variables are defined in Config.lb. */
+struct southbridge_amd_rs690_config 
+{
+	unsigned long vga_rom_address;		/* The location that the VGA rom has been appened. */
+	u8 gpp_configuration;	/* The configuration of General Purpose Port, A/B/C/D/E. */
+	u8 port_enable;		/* Which port is enabled? GFX(2,3), GPP(4,5,6,7) */
+	u8 gfx_dev2_dev3;	/* for GFX Core initialization REFCLK_SEL */
+	u8 gfx_dual_slot;		/* Is it dual graphics slots */
+	u8 gfx_lane_reversal;	/* Single/Dual slot lan reversal */
+	u8 gfx_tmds;		/* whether support TMDS? */
+	u8 gfx_compliance;	/* whether support compliance? */
+	u8 gfx_reconfiguration;	/* Dynamic Lind Width Control */
+	u8 gfx_link_width;	/* Desired width of lane 2 */
+};
+struct chip_operations;
+extern struct chip_operations southbridge_amd_rs690_ops;
+
+#endif /* RS690_CHIP_H */

Added: trunk/coreboot-v2/src/southbridge/amd/rs690/rs690.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/amd/rs690/rs690.c	                        (rev 0)
+++ trunk/coreboot-v2/src/southbridge/amd/rs690/rs690.c	2008-09-22 13:07:20 UTC (rev 3588)
@@ -0,0 +1,228 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#include <console/console.h>
+
+#include <arch/io.h>
+
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <cpu/x86/msr.h>
+#include <cpu/amd/mtrr.h>
+#include "rs690.h"
+
+static device_t find_nb_dev(device_t dev, u32 devfn)
+{
+	device_t nb_dev;
+
+	nb_dev = dev_find_slot(dev->bus->secondary, devfn);
+
+	if (!nb_dev)
+		return nb_dev;
+
+	if ((nb_dev->vendor != PCI_VENDOR_ID_ATI)
+	    || (nb_dev->device != PCI_DEVICE_ID_ATI_RS690_HT)) {
+		u32 id;
+		id = pci_read_config32(nb_dev, PCI_VENDOR_ID);
+		if (id != (PCI_VENDOR_ID_ATI | (PCI_DEVICE_ID_ATI_RS690_HT << 16))) {
+			nb_dev = 0;
+		}
+	}
+	return nb_dev;
+}
+
+/*****************************************
+* Compliant with CIM_33's ATINB_MiscClockCtrl
+*****************************************/
+void static rs690_config_misc_clk(device_t nb_dev)
+{
+	u32 reg;
+	u16 word;
+	/* u8 byte; */
+	struct bus pbus; /* fake bus for dev0 fun1 */
+
+	reg = pci_read_config32(nb_dev, 0x4c);
+	reg |= 1 << 0;
+	pci_write_config32(nb_dev, 0x4c, reg);
+
+	word = pci_cf8_conf1.read16(&pbus, 0, 1, 0xf8);
+	word &= 0xf00;
+	 pci_cf8_conf1.write16(&pbus, 0, 1, 0xf8, word);
+
+	word = pci_cf8_conf1.read16(&pbus, 0, 1, 0xe8);
+	word &= ~((1 << 12) | (1 << 13) | (1 << 14));
+	word |= 1 << 13;
+	pci_cf8_conf1.write16(&pbus, 0, 1, 0xe8, word);
+
+	reg =  pci_cf8_conf1.read32(&pbus, 0, 1, 0x94);
+	reg &= ~((1 << 16) | (1 << 24) | (1 << 28));
+	pci_cf8_conf1.write32(&pbus, 0, 1, 0x94, reg);
+
+	reg = pci_cf8_conf1.read32(&pbus, 0, 1, 0x8c);
+	reg &= ~((1 << 13) | (1 << 14) | (1 << 24) | (1 << 25));
+	reg |= 1 << 13;
+	pci_cf8_conf1.write32(&pbus, 0, 1, 0x8c, reg);
+
+	reg = pci_cf8_conf1.read32(&pbus, 0, 1, 0xcc);
+	reg |= 1 << 24;
+	pci_cf8_conf1.write32(&pbus, 0, 1, 0xcc, reg);
+
+	reg = nbmc_read_index(nb_dev, 0x7a);
+	reg &= ~0x3f;
+	reg |= 1 << 2;
+	reg &= ~(1 << 6);
+	set_htiu_enable_bits(nb_dev, 0x05, 1 << 11, 1 << 11);
+	nbmc_write_index(nb_dev, 0x7a, reg);
+	/* Powering Down efuse and strap block clocks after boot-up. GFX Mode. */
+	reg = pci_cf8_conf1.read32(&pbus, 0, 1, 0xcc);
+	reg &= ~(1 << 23);
+	reg |= 1 << 24;
+	pci_cf8_conf1.write32(&pbus, 0, 1, 0xcc, reg);
+#if 0
+	/* Powerdown reference clock to graphics core PLL in northbridge only mode */
+	reg = pci_cf8_conf1.read32(&pbus, 0, 1, 0x8c);
+	reg |= 1 << 21;
+	pci_cf8_conf1.write32(&pbus, 0, 1, 0x8c, reg);
+
+	/* Powering Down efuse and strap block clocks after boot-up. NB Only Mode. */
+	reg = pci_cf8_conf1.read32(&pbus, 0, 1, 0xcc);
+	reg |= (1 << 23) | (1 << 24);
+	pci_cf8_conf1.write32(&pbus, 0, 1, 0xcc, reg);
+
+	/* Powerdown clock to memory controller in northbridge only mode */
+	byte = pci_cf8_conf1.read8(&pbus, 0, 1, 0xe4);
+	byte |= 1 << 0;
+	pci_cf8_conf1.write8(&pbus, 0, 1, 0xe4, reg);
+
+	/* CLKCFG:0xE8 Bit[17] = 0x1 	 Powerdown clock to IOC GFX block in no external graphics mode */
+	/* TODO: */
+#endif
+
+	reg = pci_read_config32(nb_dev, 0x4c);
+	reg &= ~(1 << 0);
+	pci_write_config32(nb_dev, 0x4c, reg);
+
+	set_htiu_enable_bits(nb_dev, 0x05, 7 << 8, 7 << 8);
+}
+
+/***********************************************
+*	0:00.0  NBCFG	:
+*	0:00.1  CLK	: bit 0 of nb_cfg 0x4c : 0 - disable, default
+*	0:01.0  P2P Internal:
+*	0:02.0  P2P	: bit 2 of nbmiscind 0x0c : 0 - enable, default	   + 32 * 2
+*	0:03.0  P2P	: bit 3 of nbmiscind 0x0c : 0 - enable, default	   + 32 * 2
+*	0:04.0  P2P	: bit 4 of nbmiscind 0x0c : 0 - enable, default	   + 32 * 2
+*	0:05.0  P2P	: bit 5 of nbmiscind 0x0c : 0 - enable, default	   + 32 * 2
+*	0:06.0  P2P	: bit 6 of nbmiscind 0x0c : 0 - enable, default	   + 32 * 2
+*	0:07.0  P2P	: bit 7 of nbmiscind 0x0c : 0 - enable, default	   + 32 * 2
+*	0:08.0  NB2SB	: bit 6 of nbmiscind 0x00 : 0 - disable, default   + 32 * 1
+* case 0 will be called twice, one is by cpu in hypertransport.c line458,
+* the other is by rs690.
+***********************************************/
+void rs690_enable(device_t dev)
+{
+	device_t nb_dev = 0, sb_dev = 0;
+	int index = -1;
+	u32 i;
+	u32 devfn;
+	u32 deviceid, vendorid;
+
+	vendorid = pci_read_config32(dev, PCI_VENDOR_ID);
+	deviceid = (vendorid >> 16) & 0xffff;
+	vendorid &= 0xffff;
+	printk_info("rs690_enable VID=0x%x, DID=0x%x\n", vendorid, deviceid);
+
+	/**********************************************************
+	* Work for bus0, internal GFX located on bus1 and will return after find_nb_dev.
+	**********************************************************/
+	i = (dev->path.u.pci.devfn) & ~7;
+	for (devfn = 0; devfn <= i; devfn += (1 << 3)) {
+		nb_dev = find_nb_dev(dev, devfn);
+		if (nb_dev)
+			break;
+	}
+	if (!nb_dev) {
+		printk_info("CAN NOT FIND RS690 DEVICE!\n");
+		return;		/* nb_dev is not dev */
+	}
+
+	/* sb_dev (dev 8) is a bridge that links to southbridge. */
+	sb_dev = dev_find_slot(0, PCI_DEVFN(8, 0));
+	if (!sb_dev) {
+		printk_info("rs690_enable CAN NOT FIND SB bridge, HALT!\n");
+		for (;;) ;
+	}
+
+	printk_info("rs690_enable bus0, dev=0x%x\n", (dev->path.u.pci.devfn - devfn) >> 3);
+	switch (dev->path.u.pci.devfn - devfn) {
+	case 0:		/* bus0, dev0, fun0; */
+		printk_info("Bus-0, Dev-0, Fun-0.\n");
+		enable_pcie_bar3(nb_dev);	/* PCIEMiscInit */
+		config_gpp_core(nb_dev, sb_dev);
+		rs690_gpp_sb_init(nb_dev, sb_dev, 8);
+		/* set SB payload size: 64byte */
+		set_pcie_enable_bits(nb_dev, 0x10 | PCIE_CORE_INDEX_GPPSB, 3 << 11, 2 << 11);
+
+		/* Bus0Dev0Fun1Clock control init, we have to do it here, for dev0 Fun1 doesn't have a vendor or device ID */
+		rs690_config_misc_clk(nb_dev);
+		break;
+
+	case 1 << 3:		/* bus0, dev1 */
+		printk_info("Bus-0, Dev-1, Fun-0.\n");
+		break;
+	case 2 << 3:		/* bus0, dev2,3, two GFX */
+	case 3 << 3:
+		printk_info("Bus-0, Dev-2,3, Fun-0. enable=%d\n", dev->enabled);
+		index = (dev->path.u.pci.devfn - devfn) >> 3;
+		set_nbmisc_enable_bits(nb_dev, 0x0c, 1 << index,
+				       (dev->enabled ? 0 : 1) << index);
+		if (dev->enabled)
+			rs690_gfx_init(nb_dev, dev, index);
+		break;
+	case 4 << 3:		/* bus0, dev4-7, four GPP */
+	case 5 << 3:
+	case 6 << 3:
+	case 7 << 3:
+		printk_info("Bus-0, Dev-4,5,6,7, Fun-0. enable=%d\n",
+			    dev->enabled);
+		index = (dev->path.u.pci.devfn - devfn) >> 3;
+		set_nbmisc_enable_bits(nb_dev, 0x0c, 1 << index,
+				       (dev->enabled ? 0 : 1) << index);
+		if (dev->enabled)
+			rs690_gpp_sb_init(nb_dev, dev, index);
+		break;
+	case 8 << 3:		/* bus0, dev8, SB */
+		printk_info("Bus-0, Dev-8, Fun-0. enable=%d\n", dev->enabled);
+		set_nbmisc_enable_bits(nb_dev, 0x00, 1 << 6,
+				       (dev->enabled ? 1 : 0) << 6);
+		if (dev->enabled)
+			rs690_gpp_sb_init(nb_dev, dev, index);
+		disable_pcie_bar3(nb_dev);
+		break;
+	default:
+		printk_debug("unknown dev: %s\n", dev_path(dev));
+	}
+}
+
+struct chip_operations southbridge_amd_rs690_ops = {
+	CHIP_NAME("ATI RS690")
+	.enable_dev = rs690_enable,
+};

Added: trunk/coreboot-v2/src/southbridge/amd/rs690/rs690.h
===================================================================
--- trunk/coreboot-v2/src/southbridge/amd/rs690/rs690.h	                        (rev 0)
+++ trunk/coreboot-v2/src/southbridge/amd/rs690/rs690.h	2008-09-22 13:07:20 UTC (rev 3588)
@@ -0,0 +1,152 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#ifndef __RS690_H__
+#define __RS690_H__
+
+#include <stdint.h>
+#include "chip.h"
+
+#define PCI_DEVICE_ID_ATI_RS690_HT 0x7910
+#define PCI_DEVICE_ID_ATI_RS690_PCIE 0x7912
+#define PCI_DEVICE_ID_ATI_RS690_PCIE_DEV2 0x7913
+#define PCI_DEVICE_ID_ATI_RS690_PCIE_DEV3 0x791B
+#define PCI_DEVICE_ID_ATI_RS690_PCIE_DEV4 0x7914
+#define PCI_DEVICE_ID_ATI_RS690_PCIE_DEV5 0x7915
+#define PCI_DEVICE_ID_ATI_RS690_PCIE_DEV6 0x7916
+#define PCI_DEVICE_ID_ATI_RS690_PCIE_DEV7 0x7917
+#define PCI_DEVICE_ID_ATI_RS690_PCIE_DEV8 0x7918
+#define	PCI_DEVICE_ID_ATI_RS690_INT_GFX	  0x791e
+#define	PCI_DEVICE_ID_ATI_RS690MT_INT_GFX	  0x791f
+
+#define NBMISC_INDEX 	0x60
+#define NBHTIU_INDEX 	0xA8
+#define NBMC_INDEX 		0xE8
+#define NBPCIE_INDEX  	0xE0
+#define EXT_CONF_BASE_ADDRESS 0xE0000000
+#define	TEMP_MMIO_BASE_ADDRESS	0xC0000000
+
+typedef struct __PCIE_CFG__ {
+	u16 Config;
+	u8 ResetReleaseDelay;
+	u8 Gfx0Width;
+	u8 Gfx1Width;
+	u8 GfxPayload;
+	u8 GppPayload;
+	u8 PortDetect;
+	u8 PortHp;		/* hot plug */
+	u16 DbgConfig;
+	u32 DbgConfig2;
+	u8 GfxLx;
+	u8 GppLx;
+	u8 NBSBLx;
+	u8 PortSlotInit;
+	u8 Gfx0Pwr;
+	u8 Gfx1Pwr;
+	u8 GppPwr;
+} PCIE_CFG;
+
+/* PCIE config flags */
+#define	PCIE_DUALSLOT_CONFIG			(1 << 0)
+#define	PCIE_OVERCLOCK_ENABLE		(1 << 1)
+#define	PCIE_GPP_CLK_GATING			(1 << 2)
+#define	PCIE_ENABLE_STATIC_DEV_REMAP	(1 << 3)
+#define	PCIE_OFF_UNUSED_GFX_LANES		(1 << 4)
+#define	PCIE_OFF_UNUSED_GPP_LANES		(1 << 5)
+#define	PCIE_DISABLE_HIDE_UNUSED_PORTS	(1 << 7)
+#define	PCIE_GFX_CLK_GATING			(1 << 11)
+#define	PCIE_GFX_COMPLIANCE			(1 << 14)
+#define	PCIE_GPP_COMPLIANCE			(1 << 15)
+
+typedef enum _NB_REVISION_ {
+	REV_RS690_A11 = 5,
+	REV_RS690_A12 = 6,
+	REV_RS690_A21 = 7,
+} NB_REVISION;
+
+/* -------------------- ----------------------
+* NBMISCIND
+ ------------------- -----------------------*/
+#define	PCIE_LINK_CFG			0x8
+#define	PCIE_NBCFG_REG7		0x37
+#define	STRAPS_OUTPUT_MUX_7		0x67
+#define	STRAPS_OUTPUT_MUX_A		0x6a
+
+/* -------------------- ----------------------
+* PCIEIND
+ ------------------- -----------------------*/
+#define	PCIE_CI_CNTL			0x20
+#define	PCIE_LC_LINK_WIDTH		0xa2
+#define   PCIE_LC_STATE0			0xa5
+#define	PCIE_VC0_RESOURCE_STATUS	0x11a	/* 16bit read only */
+
+#define	PCIE_CORE_INDEX_GFX			(0 << 16) /* see 5.2.2 */
+#define	PCIE_CORE_INDEX_GPPSB		(1 << 16)
+
+/* contents of PCIE_NBCFG_REG7 */
+#define   RECONFIG_GPPSB_EN			(1 << 12)
+#define	RECONFIG_GPPSB_GPPSB			(1 << 14)
+#define   RECONFIG_GPPSB_LINK_CONFIG		(1 << 15)
+#define	RECONFIG_GPPSB_ATOMIC_RESET		(1 << 17)
+
+/* contents of PCIE_VC0_RESOURCE_STATUS */
+#define	VC_NEGOTIATION_PENDING		(1 << 1)
+
+#define	LC_STATE_RECONFIG_GPPSB		0x10
+
+/* ------------------------------------------------
+* Global variable
+* ------------------------------------------------- */
+extern PCIE_CFG AtiPcieCfg;
+
+/* ----------------- export funtions ----------------- */
+u32 nbmisc_read_index(device_t nb_dev, u32 index);
+void nbmisc_write_index(device_t nb_dev, u32 index, u32 data);
+u32 nbpcie_p_read_index(device_t dev, u32 index);
+void nbpcie_p_write_index(device_t dev, u32 index, u32 data);
+u32 nbpcie_ind_read_index(device_t nb_dev, u32 index);
+void nbpcie_ind_write_index(device_t nb_dev, u32 index, u32 data);
+u32 htiu_read_index(device_t nb_dev, u32 index);
+void htiu_write_index(device_t nb_dev, u32 index, u32 data);
+u32 nbmc_read_index(device_t nb_dev, u32 index);
+void nbmc_write_index(device_t nb_dev, u32 index, u32 data);
+
+u32 pci_ext_read_config32(device_t nb_dev, device_t dev, u32 reg);
+void pci_ext_write_config32(device_t nb_dev, device_t dev, u32 reg, u32 mask, u32 val);
+
+void set_nbcfg_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask, u32 val);
+void set_nbcfg_enable_bits_8(device_t nb_dev, u32 reg_pos, u8 mask, u8 val);
+void set_nbmc_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask, u32 val);
+void set_htiu_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask, u32 val);
+void set_nbmisc_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask, u32 val);
+void set_pcie_enable_bits(device_t dev, u32 reg_pos, u32 mask, u32 val);
+void rs690_set_tom(device_t nb_dev);
+
+void ProgK8TempMmioBase(u8 in_out, u32 pcie_base_add, u32 mmio_base_add);
+void enable_pcie_bar3(device_t nb_dev);
+void disable_pcie_bar3(device_t nb_dev);
+
+void rs690_enable(device_t dev);
+void rs690_gpp_sb_init(device_t nb_dev, device_t dev, u32 port);
+void rs690_gfx_init(device_t nb_dev, device_t dev, u32 port);
+void avoid_lpc_dma_deadlock(device_t nb_dev, device_t sb_dev);
+void config_gpp_core(device_t nb_dev, device_t sb_dev);
+void PcieReleasePortTraining(device_t nb_dev, device_t dev, u32 port);
+u8 PcieTrainPort(device_t nb_dev, device_t dev, u32 port);
+#endif				/* RS690_H */

Added: trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_cmn.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_cmn.c	                        (rev 0)
+++ trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_cmn.c	2008-09-22 13:07:20 UTC (rev 3588)
@@ -0,0 +1,314 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#include <console/console.h>
+
+#include <arch/io.h>
+
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <cpu/x86/msr.h>
+#include <cpu/amd/mtrr.h>
+#include <boot/coreboot_tables.h>
+#include <delay.h>
+#include "rs690.h"
+
+static u32 nb_read_index(device_t dev, u32 index_reg, u32 index)
+{
+	pci_write_config32(dev, index_reg, index);
+	return pci_read_config32(dev, index_reg + 0x4);
+}
+
+static void nb_write_index(device_t dev, u32 index_reg, u32 index, u32 data)
+{
+
+	pci_write_config32(dev, index_reg, index);
+	pci_write_config32(dev, index_reg + 0x4, data);
+
+}
+
+/* extension registers */
+u32 pci_ext_read_config32(device_t nb_dev, device_t dev, u32 reg)
+{
+	/*get BAR3 base address for nbcfg0x1c */
+	u32 addr = pci_read_config32(nb_dev, 0x1c);
+	printk_debug("addr=%x,bus=%x,devfn=%x\n", addr, dev->bus->secondary,
+		     dev->path.u.pci.devfn);
+	addr |= dev->bus->secondary << 20 |	/* bus num */
+	    dev->path.u.pci.devfn << 12 | reg;
+	return *((u32 *) addr);
+}
+
+void pci_ext_write_config32(device_t nb_dev, device_t dev, u32 reg_pos, u32 mask, u32 val)
+{
+	u32 reg_old, reg;
+
+	/*get BAR3 base address for nbcfg0x1c */
+	u32 addr = pci_read_config32(nb_dev, 0x1c);
+	printk_debug("write: addr=%x,bus=%x,devfn=%x\n", addr, dev->bus->secondary,
+		     dev->path.u.pci.devfn);
+	addr |= dev->bus->secondary << 20 |	/* bus num */
+	    dev->path.u.pci.devfn << 12 | reg_pos;
+
+	reg = reg_old = *((u32 *) addr);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		*((u32 *) addr) = val;
+	}
+}
+
+u32 nbmisc_read_index(device_t nb_dev, u32 index)
+{
+	return nb_read_index((nb_dev), NBMISC_INDEX, (index));
+}
+
+void nbmisc_write_index(device_t nb_dev, u32 index, u32 data)
+{
+	nb_write_index((nb_dev), NBMISC_INDEX, ((index) | 0x80), (data));
+}
+
+u32 nbpcie_p_read_index(device_t dev, u32 index)
+{
+	return nb_read_index((dev), NBPCIE_INDEX, (index));
+}
+
+void nbpcie_p_write_index(device_t dev, u32 index, u32 data)
+{
+	nb_write_index((dev), NBPCIE_INDEX, (index), (data));
+}
+
+u32 nbpcie_ind_read_index(device_t nb_dev, u32 index)
+{
+	return nb_read_index((nb_dev), NBPCIE_INDEX, (index));
+}
+
+void nbpcie_ind_write_index(device_t nb_dev, u32 index, u32 data)
+{
+	nb_write_index((nb_dev), NBPCIE_INDEX, (index), (data));
+}
+
+u32 htiu_read_index(device_t nb_dev, u32 index)
+{
+	return nb_read_index((nb_dev), NBHTIU_INDEX, (index));
+}
+
+void htiu_write_index(device_t nb_dev, u32 index, u32 data)
+{
+	nb_write_index((nb_dev), NBHTIU_INDEX, ((index) | 0x100), (data));
+}
+
+u32 nbmc_read_index(device_t nb_dev, u32 index)
+{
+	return nb_read_index((nb_dev), NBMC_INDEX, (index));
+}
+
+void nbmc_write_index(device_t nb_dev, u32 index, u32 data)
+{
+	nb_write_index((nb_dev), NBMC_INDEX, ((index) | 1 << 9), (data));
+}
+
+void set_nbcfg_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask, u32 val)
+{
+	u32 reg_old, reg;
+	reg = reg_old = pci_read_config32(nb_dev, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		pci_write_config32(nb_dev, reg_pos, reg);
+	}
+}
+
+void set_nbcfg_enable_bits_8(device_t nb_dev, u32 reg_pos, u8 mask, u8 val)
+{
+	u8 reg_old, reg;
+	reg = reg_old = pci_read_config8(nb_dev, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		pci_write_config8(nb_dev, reg_pos, reg);
+	}
+}
+
+void set_nbmc_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask, u32 val)
+{
+	u32 reg_old, reg;
+	reg = reg_old = nbmc_read_index(nb_dev, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		nbmc_write_index(nb_dev, reg_pos, reg);
+	}
+}
+
+void set_htiu_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask, u32 val)
+{
+	u32 reg_old, reg;
+	reg = reg_old = htiu_read_index(nb_dev, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		htiu_write_index(nb_dev, reg_pos, reg);
+	}
+}
+
+void set_nbmisc_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask, u32 val)
+{
+	u32 reg_old, reg;
+	reg = reg_old = nbmisc_read_index(nb_dev, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		nbmisc_write_index(nb_dev, reg_pos, reg);
+	}
+}
+
+void set_pcie_enable_bits(device_t dev, u32 reg_pos, u32 mask, u32 val)
+{
+	u32 reg_old, reg;
+	reg = reg_old = nb_read_index(dev, NBPCIE_INDEX, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		nb_write_index(dev, NBPCIE_INDEX, reg_pos, reg);
+	}
+}
+
+/***********************************************************
+* To access bar3 we need to program PCI MMIO 7 in K8.
+* in_out:
+*	1: enable/enter k8 temp mmio base
+*	0: disable/restore
+***********************************************************/
+void ProgK8TempMmioBase(u8 in_out, u32 pcie_base_add, u32 mmio_base_add)
+{
+	/* K8 Function1 is address map */
+	device_t k8_f1 = dev_find_slot(0, PCI_DEVFN(0x18, 1));
+
+	if (in_out) {
+		pci_write_config32(k8_f1, 0xbc,
+				   (((pcie_base_add + 0x10000000 -
+				     1) >> 8) & 0xffffff00) | 0x8);
+		pci_write_config32(k8_f1, 0xb8, (pcie_base_add >> 8) | 0x3);
+		pci_write_config32(k8_f1, 0xb4,
+				   ((mmio_base_add + 0x10000000 -
+				     1) >> 8) & 0xffffff00);
+		pci_write_config32(k8_f1, 0xb0, (mmio_base_add >> 8) | 0x3);
+	} else {
+		pci_write_config32(k8_f1, 0xb8, 0);
+		pci_write_config32(k8_f1, 0xbc, 0);
+		pci_write_config32(k8_f1, 0xb0, 0);
+		pci_write_config32(k8_f1, 0xb4, 0);
+	}
+}
+
+void PcieReleasePortTraining(device_t nb_dev, device_t dev, u32 port)
+{
+	switch (port) {
+	case 2:		/* GFX, bit4-5 */
+	case 3:
+		set_nbmisc_enable_bits(nb_dev, PCIE_LINK_CFG,
+				       1 << (port + 2), 0 << (port + 2));
+		break;
+	case 4:		/* GPP, bit20-24 */
+	case 5:
+	case 6:
+	case 7:
+		set_nbmisc_enable_bits(nb_dev, PCIE_LINK_CFG,
+				       1 << (port + 17), 0 << (port + 17));
+		break;
+	}
+}
+
+/********************************************************************************************************
+* Output:
+*	0: no device is present.
+*	1: device is present and is trained.
+********************************************************************************************************/
+u8 PcieTrainPort(device_t nb_dev, device_t dev, u32 port)
+{
+	u16 count = 5000;
+	u32 lc_state, reg;
+	int8_t current, res = 0;
+
+	while (count--) {
+		mdelay(40);
+		udelay(200);
+		lc_state = nbpcie_p_read_index(dev, 0xa5);	/* lc_state */
+		printk_debug("PcieLinkTraining port=%x:lc current state=%x\n",
+			     port, lc_state);
+		current = lc_state & 0x3f;	/* get LC_CURRENT_STATE, bit0-5 */
+
+		switch (current) {
+		case 0x00:	/* 0x00-0x04 means no device is present */
+		case 0x01:
+		case 0x02:
+		case 0x03:
+		case 0x04:
+			res = 0;
+			count = 0;
+			break;
+		case 0x07:	/* device is in compliance state (training sequence is doen). Move to train the next device */
+			res = 1;	/* TODO: CIM sets it to 0 */
+			count = 0;
+			break;
+		case 0x10:
+			reg =
+			    pci_ext_read_config32(nb_dev, dev,
+						  PCIE_VC0_RESOURCE_STATUS);
+			printk_debug("PcieTrainPort reg=0x%x\n", reg);
+			/* check bit1 */
+			if (reg & VC_NEGOTIATION_PENDING) {	/* bit1=1 means the link needs to be re-trained. */
+				/* set bit8=1, bit0-2=bit4-6 */
+				u32 tmp;
+				reg =
+				    nbpcie_p_read_index(dev,
+							PCIE_LC_LINK_WIDTH);
+				tmp = (reg >> 4) && 0x3;	/* get bit4-6 */
+				reg &= 0xfff8;	/* clear bit0-2 */
+				reg += tmp;	/* merge */
+				reg |= 1 << 8;
+				count++;	/* CIM said "keep in loop"?  */
+			} else {
+				res = 1;
+				count = 0;
+			}
+			break;
+		default:	/* reset pcie */
+			res = 0;
+			count = 0;	/* break loop */
+			break;
+		}
+	}
+	return res;
+}
+
+/*
+* Compliant with CIM_33's ATINB_SetToms.
+* Set Top Of Memory below and above 4G.
+*/
+void rs690_set_tom(device_t nb_dev)
+{
+	/* set TOM */
+	pci_write_config32(nb_dev, 0x90, uma_memory_start);
+	nbmc_write_index(nb_dev, 0x1e, uma_memory_start);
+}
+

Added: trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_early_setup.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_early_setup.c	                        (rev 0)
+++ trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_early_setup.c	2008-09-22 13:07:20 UTC (rev 3588)
@@ -0,0 +1,469 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+
+ 
+#define NBHTIU_INDEX		0xA8
+#define NBMISC_INDEX		0x60
+#define NBMC_INDEX 		0xE8
+
+static u32 nb_read_index(device_t dev, u32 index_reg, u32 index)
+{
+	pci_write_config32(dev, index_reg, index);
+	return pci_read_config32(dev, index_reg + 0x4);
+}
+
+static void nb_write_index(device_t dev, u32 index_reg, u32 index, u32 data)
+{
+	pci_write_config32(dev, index_reg, index /* | 0x80 */ );
+	pci_write_config32(dev, index_reg + 0x4, data);
+}
+
+static u32 nbmisc_read_index(device_t nb_dev, u32 index)
+{
+	return nb_read_index((nb_dev), NBMISC_INDEX, (index));
+}
+
+static void nbmisc_write_index(device_t nb_dev, u32 index, u32 data)
+{
+	nb_write_index((nb_dev), NBMISC_INDEX, ((index) | 0x80), (data));
+}
+
+static u32 htiu_read_index(device_t nb_dev, u32 index)
+{
+	return nb_read_index((nb_dev), NBHTIU_INDEX, (index));
+}
+
+static void htiu_write_index(device_t nb_dev, u32 index, u32 data)
+{
+	nb_write_index((nb_dev), NBHTIU_INDEX, ((index) | 0x100), (data));
+}
+
+static u32 nbmc_read_index(device_t nb_dev, u32 index)
+{
+	return nb_read_index((nb_dev), NBMC_INDEX, (index));
+}
+
+static void nbmc_write_index(device_t nb_dev, u32 index, u32 data)
+{
+	nb_write_index((nb_dev), NBMC_INDEX, ((index) | 1 << 9), (data));
+}
+
+static void set_htiu_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask,
+				 u32 val)
+{
+	u32 reg_old, reg;
+	reg = reg_old = htiu_read_index(nb_dev, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		htiu_write_index(nb_dev, reg_pos, reg);
+	}
+}
+
+static void set_nbmisc_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask,
+				   u32 val)
+{
+	u32 reg_old, reg;
+	reg = reg_old = nbmisc_read_index(nb_dev, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		nbmisc_write_index(nb_dev, reg_pos, reg);
+	}
+}
+
+static void set_nbcfg_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask,
+				  u32 val)
+{
+	u32 reg_old, reg;
+	reg = reg_old = pci_read_config32(nb_dev, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		pci_write_config32(nb_dev, reg_pos, reg);
+	}
+}
+
+static void set_nbcfg_enable_bits_8(device_t nb_dev, u32 reg_pos, u8 mask,
+				    u8 val)
+{
+	u8 reg_old, reg;
+	reg = reg_old = pci_read_config8(nb_dev, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		pci_write_config8(nb_dev, reg_pos, reg);
+	}
+}
+
+static void set_nbmc_enable_bits(device_t nb_dev, u32 reg_pos, u32 mask,
+				 u32 val)
+{
+	u32 reg_old, reg;
+	reg = reg_old = nbmc_read_index(nb_dev, reg_pos);
+	reg &= ~mask;
+	reg |= val;
+	if (reg != reg_old) {
+		nbmc_write_index(nb_dev, reg_pos, reg);
+	}
+}
+
+/*
+* Compliant with CIM_33's ATINB_PrepareInit
+*/
+static void get_cpu_rev()
+{
+	u32 eax, ebx, ecx, edx;
+	__asm__ volatile ("cpuid":"=a" (eax), "=b"(ebx), "=c"(ecx), "=d"(edx)
+			  :"0"(1));
+	printk_info("get_cpu_rev EAX=0x%x.\n", eax);
+	if (eax <= 0xfff)
+		printk_info("CPU Rev is K8_Cx.\n");
+	else if (eax <= 0x10fff)
+		printk_info("CPU Rev is K8_Dx.\n");
+	else if (eax <= 0x20fff)
+		printk_info("CPU Rev is K8_Ex.\n");
+	else if (eax <= 0x40fff)
+		printk_info("CPU Rev is K8_Fx.\n");
+	else if (eax == 0x60fb1 || eax == 0x60f81)	/*These two IDS are exception, they are G1. */
+		printk_info("CPU Rev is K8_G1.\n");
+	else if (eax <= 0X60FF0)
+		printk_info("CPU Rev is K8_G0.\n");
+	else if (eax <= 0x100000)
+		printk_info("CPU Rev is K8_G1.\n");
+	else
+		printk_info("CPU Rev is K8_10.\n");
+}
+
+static u8 get_nb_rev(device_t nb_dev)
+{
+	u32 reg;
+	reg = pci_read_config32(nb_dev, 0x00);
+	if (0x7911 == (reg >> 16))
+		return 7;
+	reg = pci_read_config8(nb_dev, 0x89);	/* copy from CIM, can't find in doc */
+	if (reg & 0x2)		/* check bit1 */
+		return 7;
+	if (reg & 0x1)		/* check bit0 */
+		return 6;
+	else
+		return 5;
+}
+
+/*****************************************
+* Compliant with CIM_33's ATINB_HTInit
+* Init HT link speed/width for rs690 -- k8 link
+*****************************************/
+static void rs690_htinit()
+{
+	/*
+	 * About HT, it has been done in enumerate_ht_chain().
+	 */
+	device_t k8_f0;
+	u32 reg;
+	u8 k8_ht_freq;
+
+	k8_f0 = PCI_DEV(0, 0x18, 0);
+	/************************
+	* get k8's ht freq, in k8's function 0, offset 0x88
+	* bit11-8, specifics the maximum operation frequency of the link's transmitter clock.
+	* The link frequency field (Frq) is cleared by cold reset. SW can write a nonzero
+	* value to this reg, and that value takes effect on the next warm reset or 
+	* LDTSTOP_L disconnect sequence.
+	* 0000b = 200Mhz
+	* 0010b = 400Mhz
+	* 0100b = 600Mhz
+	* 0101b = 800Mhz
+	* 0110b = 1Ghz
+	* 1111b = 1Ghz
+	************************/
+	reg = pci_read_config32(k8_f0, 0x88);
+	k8_ht_freq = (reg & 0xf00) >> 8;
+	printk_info("rs690_ht_init k8_ht_freq=%x.\n", k8_ht_freq);
+}
+
+/*******************************************************
+* Optimize k8 with UMA.
+* See BKDG_NPT_0F guide for details.
+* The processor node is addressed by its Node ID on the HT link and can be
+* accessed with a device number in the PCI configuration space on Bus0.
+* The Node ID 0 is mapped to Device 24 (0x18), the Node ID 1 is mapped
+* to Device 25, and so on.
+* The processor implements configuration registers in PCI configuration
+* space using the following four headers
+*	Function0: HT technology configuration
+*	Function1: Address map configuration
+*	Function2: DRAM and HT technology Trace mode configuration
+*	Function3: Miscellaneous configuration
+*******************************************************/
+static void k8_optimization()
+{
+	device_t k8_f0, k8_f2, k8_f3;
+	msr_t msr;
+
+	printk_info("k8_optimization()\n");
+	k8_f0 = PCI_DEV(0, 0x18, 0);
+	k8_f2 = PCI_DEV(0, 0x18, 2);
+	k8_f3 = PCI_DEV(0, 0x18, 3);
+
+	pci_write_config32(k8_f0, 0x90, 0x01700178);	/* CIM NPT_Optimization */
+	set_nbcfg_enable_bits(k8_f0, 0x68, 1 << 28, 0 << 28);
+	set_nbcfg_enable_bits(k8_f0, 0x68, 1 << 26 | 1 << 27,
+			      1 << 26 | 1 << 27);
+	set_nbcfg_enable_bits(k8_f0, 0x68, 1 << 11, 1 << 11);
+	set_nbcfg_enable_bits(k8_f0, 0x84, 1 << 11 | 1 << 13 | 1 << 15, 1 << 11 | 1 << 13 | 1 << 15);	/* TODO */
+
+	pci_write_config32(k8_f3, 0x70, 0x51320111);	/* CIM NPT_Optimization */
+	pci_write_config32(k8_f3, 0x74, 0x50304021);
+	pci_write_config32(k8_f3, 0x78, 0x08002A00);
+	if (pci_read_config32(k8_f3, 0xE8) & 0x3<<12)
+		pci_write_config32(k8_f3, 0x7C, 0x0000211B); /* dual core */
+	else
+		pci_write_config32(k8_f3, 0x7C, 0x0000211C); /* single core */
+	set_nbcfg_enable_bits_8(k8_f3, 0xDC, 0xFF, 0x25);
+
+	set_nbcfg_enable_bits(k8_f2, 0xA0, 1 << 5, 1 << 5);
+	set_nbcfg_enable_bits(k8_f2, 0x94, 0xF << 24, 7 << 24);
+	set_nbcfg_enable_bits(k8_f2, 0x90, 1 << 10, 1 << 10);
+	set_nbcfg_enable_bits(k8_f2, 0xA0, 3 << 2, 3 << 2);
+	set_nbcfg_enable_bits(k8_f2, 0xA0, 1 << 5, 1 << 5);
+
+	msr = rdmsr(0xC001001F);
+	msr.lo &= ~(1 << 9);
+	msr.hi &= ~(1 << 4);
+	wrmsr(0xC001001F, msr);
+}
+
+/*****************************************
+* Compliant with CIM_33's ATINB_PCICFG_POR_TABLE
+*****************************************/
+static void rs690_por_pcicfg_init(device_t nb_dev)
+{
+	/* enable PCI Memory Access */
+	set_nbcfg_enable_bits_8(nb_dev, 0x04, (u8)(~0xFD), 0x02);
+	/* Set RCRB Enable */
+	set_nbcfg_enable_bits_8(nb_dev, 0x84, (u8)(~0xFF), 0x1);
+	/* allow decode of 640k-1MB */
+	set_nbcfg_enable_bits_8(nb_dev, 0x84, (u8)(~0xEF), 0x10);
+	/* Enable PM2_CNTL(BAR2) IO mapped cfg write access to be broadcast to both NB and SB */
+	set_nbcfg_enable_bits_8(nb_dev, 0x84, (u8)(~0xFF), 0x4);
+	/* Power Management Register Enable */
+	set_nbcfg_enable_bits_8(nb_dev, 0x84, (u8)(~0xFF), 0x80);
+
+	/* Reg4Ch[1]=1 (APIC_ENABLE) force cpu request with address 0xFECx_xxxx to south-bridge
+	 * Reg4Ch[6]=1 (BMMsgEn) enable BM_Set message generation
+	 * BMMsgEn */
+	set_nbcfg_enable_bits_8(nb_dev, 0x4C, (u8)(~0x00), 0x42 | 1);
+
+	/* Reg4Ch[16]=1 (WakeC2En) enable Wake_from_C2 message generation.
+	 * Reg4Ch[18]=1 (P4IntEnable) Enable north-bridge to accept MSI with address 0xFEEx_xxxx from south-bridge */
+	set_nbcfg_enable_bits_8(nb_dev, 0x4E, (u8)(~0xFF), 0x05);
+	/* Reg94h[4:0] = 0x0  P drive strength offset 0
+	 * Reg94h[6:5] = 0x2  P drive strength additive adjust */
+	set_nbcfg_enable_bits_8(nb_dev, 0x94, (u8)(~0x80), 0x40);
+
+	/* Reg94h[20:16] = 0x0  N drive strength offset 0
+	 * Reg94h[22:21] = 0x2  N drive strength additive adjust */
+	set_nbcfg_enable_bits_8(nb_dev, 0x96, (u8)(~0x80), 0x40);
+
+	/* Reg80h[4:0] = 0x0  Termination offset
+	 * Reg80h[6:5] = 0x2  Termination additive adjust */
+	set_nbcfg_enable_bits_8(nb_dev, 0x80, (u8)(~0x80), 0x40);
+
+	/* Reg80h[14] = 0x1   Enable receiver termination control */
+	set_nbcfg_enable_bits_8(nb_dev, 0x81, (u8)(~0xFF), 0x40);
+
+	/* Reg94h[15] = 0x1 Enables HT transmitter advanced features to be turned on
+	 * Reg94h[14] = 0x1  Enable drive strength control */
+	set_nbcfg_enable_bits_8(nb_dev, 0x95, (u8)(~0x3F), 0xC4);
+
+	/* Reg94h[31:29] = 0x7 Enables HT transmitter de-emphasis */
+	set_nbcfg_enable_bits_8(nb_dev, 0x97, (u8)(~0x1F), 0xE0);
+
+	/*Reg8Ch[10:9] = 0x3 Enables Gfx Debug BAR,
+	 * force this BAR as mem type in rs690_gfx.c */
+	set_nbcfg_enable_bits_8(nb_dev, 0x8D, (u8)(~0xFF), 0x03);
+	
+}
+
+/*****************************************
+* Compliant with CIM_33's ATINB_MCIndex_POR_TABLE
+*****************************************/
+static void rs690_por_mc_index_init(device_t nb_dev)
+{
+	set_nbmc_enable_bits(nb_dev, 0x7A, ~0xFFFFFF80, 0x0000005F);
+	set_nbmc_enable_bits(nb_dev, 0xD8, ~0x00000000, 0x00600060);
+	set_nbmc_enable_bits(nb_dev, 0xD9, ~0x00000000, 0x00600060);
+	set_nbmc_enable_bits(nb_dev, 0xE0, ~0x00000000, 0x00000000);
+	set_nbmc_enable_bits(nb_dev, 0xE1, ~0x00000000, 0x00000000);
+	set_nbmc_enable_bits(nb_dev, 0xE8, ~0x00000000, 0x003E003E);
+	set_nbmc_enable_bits(nb_dev, 0xE9, ~0x00000000, 0x003E003E);
+}
+
+/*****************************************
+* Compliant with CIM_33's ATINB_MISCIND_POR_TABLE
+* Compliant with CIM_33's MISC_INIT_TBL
+*****************************************/
+static void rs690_por_misc_index_init(device_t nb_dev)
+{
+	/* NB_MISC_IND_WR_EN + IOC_PCIE_CNTL
+	 * Block non-snoop DMA request if PMArbDis is set.
+	 * Set BMSetDis */
+	set_nbmisc_enable_bits(nb_dev, 0x0B, ~0xFFFF0000, 0x00000180);
+	set_nbmisc_enable_bits(nb_dev, 0x01, ~0xFFFFFFFF, 0x00000040);
+
+	/* NBCFG (NBMISCIND 0x0): NB_CNTL -
+	 *   HIDE_NB_AGP_CAP  ([0], default=1)HIDE
+	 *   HIDE_P2P_AGP_CAP ([1], default=1)HIDE
+	 *   HIDE_NB_GART_BAR ([2], default=1)HIDE
+	 *   AGPMODE30        ([4], default=0)DISABLE
+	 *   AGP30ENCHANCED   ([5], default=0)DISABLE
+	 *   HIDE_AGP_CAP     ([8], default=1)ENABLE */
+	set_nbmisc_enable_bits(nb_dev, 0x00, ~0xFFFF0000, 0x00000506);	/* set bit 10 for MSI */
+
+	/* NBMISCIND:0x6A[16]= 1 SB link can get a full swing
+	 *      set_nbmisc_enable_bits(nb_dev, 0x6A, 0ffffffffh, 000010000);
+	 * NBMISCIND:0x6A[17]=1 Set CMGOOD_OVERRIDE. */
+	set_nbmisc_enable_bits(nb_dev, 0x6A, ~0xffffffff, 0x00020000);
+
+	/* NBMISIND:0x40 Bit[8]=1 and Bit[10]=1 following bits are required to set in order to allow LVDS or PWM features to work. */
+	set_nbmisc_enable_bits(nb_dev, 0x40, ~0xffffffff, 0x00000500);
+
+	/* NBMISIND:0xC Bit[13]=1 Enable GSM mode for C1e or C3 with pop-up. */
+	set_nbmisc_enable_bits(nb_dev, 0x0C, ~0xffffffff, 0x00002000);
+
+	/* Set NBMISIND:0x1F[3] to map NB F2 interrupt pin to INTB# */
+	set_nbmisc_enable_bits(nb_dev, 0x1F, ~0xffffffff, 0x00000008);
+
+	/* Compliant with CIM_33's MISC_INIT_TBL, except Hide NB_BAR3_PCIE
+	 * Enable access to DEV8
+	 * Enable setPower message for all ports
+	 */
+	set_nbmisc_enable_bits(nb_dev, 0x00, 1 << 6, 1 << 6);
+	set_nbmisc_enable_bits(nb_dev, 0x0b, 1 << 20, 1 << 20);
+	set_nbmisc_enable_bits(nb_dev, 0x51, 1 << 20, 1 << 20);
+	set_nbmisc_enable_bits(nb_dev, 0x53, 1 << 20, 1 << 20);
+	set_nbmisc_enable_bits(nb_dev, 0x55, 1 << 20, 1 << 20);
+	set_nbmisc_enable_bits(nb_dev, 0x57, 1 << 20, 1 << 20);
+	set_nbmisc_enable_bits(nb_dev, 0x59, 1 << 20, 1 << 20);
+	set_nbmisc_enable_bits(nb_dev, 0x5B, 1 << 20, 1 << 20);
+
+	set_nbmisc_enable_bits(nb_dev, 0x00, 1 << 7, 1 << 7);
+	set_nbmisc_enable_bits(nb_dev, 0x07, 0x000000f0, 0x30);
+	/* Disable bus-master trigger event from SB and Enable set_slot_power message to SB */
+	set_nbmisc_enable_bits(nb_dev, 0x0B, 0xffffffff, 0x500180);
+}
+
+/*****************************************
+* Compliant with CIM_33's ATINB_HTIUNBIND_POR_TABLE
+*****************************************/
+static void rs690_por_htiu_index_init(device_t nb_dev)
+{
+	/* 0xBC:
+	* Enables GSM mode for C1e or C3 with pop-up
+	* Prevents AllowLdtStop from being asserted during HT link recovery
+	* Allows FID cycles to be serviced faster. Needed for RS690 A12. No harm in RS690 A11 */
+	set_htiu_enable_bits(nb_dev, 0x05, ~0xffffffff, 0x0BC);
+	/* 0x4203A202:
+	* Enables writes to pass in-progress reads
+	* Enables streaming of CPU writes
+	* Enables extended write buffer for CPU writes
+	* Enables additional response buffers
+	* Enables special reads to pass writes
+	* Enables decoding of C1e/C3 and FID cycles
+	* Enables HTIU-display handshake bypass.
+	* Enables tagging fix */
+	set_htiu_enable_bits(nb_dev, 0x06, ~0xFFFFFFFE, 0x4203A202);
+
+	/* Enables byte-write optimization for IOC requests
+	* Disables delaying STPCLK de-assert during FID sequence. Needed when enhanced UMA arbitration is used.
+	* Disables upstream system-management delay */
+	set_htiu_enable_bits(nb_dev, 0x07, ~0xFFFFFFF9, 0x001);
+
+	/* HTIUNBIND 0x16 [1] = 0x1     Enable crc decoding fix */
+	set_htiu_enable_bits(nb_dev, 0x16, ~0xFFFFFFFF, 0x2);
+}
+
+/*****************************************
+* Compliant with CIM_33's ATINB_POR_INIT_JMPDI
+* Configure RS690 registers to power-on default RPR.
+* POR: Power On Reset
+* RPR: Register Programming Requirements
+*****************************************/
+static void rs690_por_init(device_t nb_dev)
+{
+	printk_info("rs690_por_init\n");
+	/* ATINB_PCICFG_POR_TABLE, initialize the values for rs690 PCI Config registers */
+	rs690_por_pcicfg_init(nb_dev);
+
+	/* ATINB_MCIND_POR_TABLE */
+	rs690_por_mc_index_init(nb_dev);
+
+	/* ATINB_MISCIND_POR_TABLE */
+	rs690_por_misc_index_init(nb_dev);
+
+	/* ATINB_HTIUNBIND_POR_TABLE */
+	rs690_por_htiu_index_init(nb_dev);
+
+	/* ATINB_CLKCFG_PORT_TABLE */
+	/* rs690 A11 SB Link full swing? */
+}
+
+/* enable CFG access to Dev8, which is the SB P2P Bridge */
+static void enable_rs690_dev8()
+{
+	set_nbmisc_enable_bits(PCI_DEV(0, 0, 0), 0x00, 1 << 6, 1 << 6);
+}
+
+
+
+/*
+* Compliant with CIM_33's AtiNBInitEarlyPost (AtiInitNBBeforePCIInit).
+*/
+static void rs690_before_pci_init()
+{
+}
+
+/*
+* The calling sequence is same as CIM.
+*/
+static void rs690_early_setup()
+{
+	device_t nb_dev = PCI_DEV(0, 0, 0);
+	printk_info("rs690_early_setup()\n");
+
+	/*ATINB_PrepareInit */
+	get_cpu_rev();
+	switch (get_nb_rev(nb_dev)) {	/* PCIEMiscInit */
+	case 5:
+		printk_info("NB Revision is A11.\n");
+		break;
+	case 6:
+		printk_info("NB Revision is A12.\n");
+		break;
+	case 7:
+		printk_info("NB Revision is A21.\n");
+		break;
+	}
+
+	rs690_htinit();
+	k8_optimization();
+	rs690_por_init(nb_dev);
+}

Added: trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_gfx.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_gfx.c	                        (rev 0)
+++ trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_gfx.c	2008-09-22 13:07:20 UTC (rev 3588)
@@ -0,0 +1,582 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+/*
+ *  for rs690 internal graphics device
+ *  device id of internal grphics:
+ *	RS690M/T: 0x791f
+ *    RS690:	   0x791e
+ */
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <delay.h>
+#include "rs690.h"
+
+#define CLK_CNTL_INDEX	0x8
+#define CLK_CNTL_DATA	0xC
+
+static u32 clkind_read(device_t dev, u32 index)
+{
+	u32	gfx_bar2 = pci_read_config32(dev, 0x18) & ~0xF;
+
+	*(u32*)(gfx_bar2+CLK_CNTL_INDEX) = index & 0x7F;
+	return *(u32*)(gfx_bar2+CLK_CNTL_DATA);
+}
+
+static void clkind_write(device_t dev, u32 index, u32 data)
+{
+	u32	gfx_bar2 = pci_read_config32(dev, 0x18) & ~0xF;
+	/* printk_info("gfx bar 2 %02x\n", gfx_bar2); */
+
+	*(u32*)(gfx_bar2+CLK_CNTL_INDEX) = index | 1<<7;
+	*(u32*)(gfx_bar2+CLK_CNTL_DATA)  = data;
+}
+
+/*
+* pci_dev_read_resources thinks it is a IO type.
+* We have to force it to mem type.
+*/
+static void rs690_gfx_read_resources(device_t dev)
+{
+	printk_info("rs690_gfx_read_resources.\n");
+
+	/* The initial value of 0x24 is 0xFFFFFFFF, which is confusing.
+	   Even if we write 0xFFFFFFFF into it, it will be 0xFFF00000,
+	   which tells us it is a memory address base.
+	 */
+	pci_write_config32(dev, 0x24, 0x00000000);
+
+	/* Get the normal pci resources of this device */
+	pci_dev_read_resources(dev);
+	compact_resources(dev);
+}
+
+static void internal_gfx_pci_dev_init(struct device *dev)
+{
+	unsigned short deviceid, vendorid;
+	struct southbridge_amd_rs690_config *cfg =
+	    (struct southbridge_amd_rs690_config *)dev->chip_info;
+	deviceid = pci_read_config16(dev, PCI_DEVICE_ID);
+	vendorid = pci_read_config16(dev, PCI_VENDOR_ID);
+	printk_info("internal_gfx_pci_dev_init device=%x, vendor=%x, vga_rom_address=0x%x.\n",
+	     deviceid, vendorid, cfg->vga_rom_address);
+
+#if 0 /* I think these should be done in Config.lb. Please check it. */
+	dev->on_mainboard = 1;
+	dev->rom_address = cfg->vga_rom_address;	/* 0xfff00000; */
+#endif
+	pci_dev_init(dev);
+
+	/* clk ind */
+	clkind_write(dev, 0x08, 0x01);
+	clkind_write(dev, 0x0C, 0x22);
+	clkind_write(dev, 0x0F, 0x0);
+	clkind_write(dev, 0x11, 0x0);
+	clkind_write(dev, 0x12, 0x0);
+	clkind_write(dev, 0x14, 0x0);
+	clkind_write(dev, 0x15, 0x0);
+	clkind_write(dev, 0x16, 0x0);
+	clkind_write(dev, 0x17, 0x0);
+	clkind_write(dev, 0x18, 0x0);
+	clkind_write(dev, 0x19, 0x0);
+	clkind_write(dev, 0x1A, 0x0);
+	clkind_write(dev, 0x1B, 0x0);
+	clkind_write(dev, 0x1C, 0x0);
+	clkind_write(dev, 0x1D, 0x0);
+	clkind_write(dev, 0x1E, 0x0);
+	clkind_write(dev, 0x26, 0x0);
+	clkind_write(dev, 0x27, 0x0);
+	clkind_write(dev, 0x28, 0x0);
+	clkind_write(dev, 0x5C, 0x0);
+}
+
+static void rs690_gfx_set_resources(struct device *dev)
+{
+	printk_info("rs690_gfx_set_resources.\n");
+	pci_dev_set_resources(dev);
+}
+
+/*
+* Set registers in RS690 and CPU to enable the internal GFX.
+* Please refer to CIM source code and BKDG.
+*/
+static void rs690_internal_gfx_enable(device_t dev)
+{
+	u32 l_dword;
+	int i;
+	device_t k8_f0 = 0, k8_f2 = 0;
+	device_t nb_dev = dev_find_slot(0, 0);
+
+	printk_info("rs690_internal_gfx_enable dev=0x%x, nb_dev=0x%x.\n", dev,
+		    nb_dev);
+
+	/* set APERTURE_SIZE, 128M. */
+	l_dword = pci_read_config32(nb_dev, 0x8c);
+	printk_info("nb_dev, 0x8c=0x%x\n", l_dword);
+	l_dword &= 0xffffff8f;
+	pci_write_config32(nb_dev, 0x8c, l_dword);
+
+	/* set TOM */
+	rs690_set_tom(nb_dev);
+	
+	/* LPC DMA Deadlock workaround? */
+	k8_f0 = dev_find_slot(0, PCI_DEVFN(0x18, 0));
+	l_dword = pci_read_config32(k8_f0, 0x68);
+	l_dword &= ~(1 << 22);
+	l_dword |= (1 << 21);
+	pci_write_config32(k8_f0, 0x68, l_dword);
+
+	/* Enable 64bit mode. */
+	set_nbmc_enable_bits(nb_dev, 0x5f, 0, 1 << 9);
+	set_nbmc_enable_bits(nb_dev, 0xb0, 0, 1 << 8);
+
+	/* 64bit Latency. */
+	set_nbmc_enable_bits(nb_dev, 0x5f, 0x7c00, 0x800);
+
+	/* UMA dual channel control register. */
+	nbmc_write_index(nb_dev, 0x86, 0x3d);
+
+	/* check the setting later!! */
+	set_htiu_enable_bits(nb_dev, 0x07, 1 << 7, 0);
+
+	/* UMA mode, powerdown memory PLL. */
+	set_nbmc_enable_bits(nb_dev, 0x74, 0, 1 << 31);
+
+	/* Copy CPU DDR Controller to NB MC. */
+	/* Why K8_MC_REG80 is special? */
+	k8_f2 = dev_find_slot(0, PCI_DEVFN(0x18, 2));
+	for (i = 0; i <= (0x80 - 0x40) / 4; i++) {
+		l_dword = pci_read_config32(k8_f2, 0x40 + i * 4);
+		nbmc_write_index(nb_dev, 0x63 + i, l_dword);
+	}
+
+	/* Set K8 MC for UMA, Family F. */
+	l_dword = pci_read_config32(k8_f2, 0xa0);
+	l_dword |= 0x2c;
+	pci_write_config32(k8_f2, 0xa0, l_dword);
+	l_dword = pci_read_config32(k8_f2, 0x94);
+	l_dword &= 0xf0ffffff;
+	l_dword |= 0x07000000;
+	pci_write_config32(k8_f2, 0x94, l_dword);
+
+	/* set FB size and location. */
+	nbmc_write_index(nb_dev, 0x1b, 0x00);
+	l_dword = nbmc_read_index(nb_dev, 0x1c);
+	l_dword &= 0xffff0;
+	l_dword |= 0x400 << 20;
+	l_dword |= 0x4;
+	nbmc_write_index(nb_dev, 0x1c, l_dword);
+	l_dword = nbmc_read_index(nb_dev, 0x1d);
+	l_dword &= 0xfffff000;
+	l_dword |= 0x0400;
+	nbmc_write_index(nb_dev, 0x1d, l_dword);
+	nbmc_write_index(nb_dev, 0x100, 0x3fff3800);
+
+	/* Program MC table. */
+	set_nbmc_enable_bits(nb_dev, 0x00, 0, 1 << 31);
+	l_dword = nbmc_read_index(nb_dev, 0x91);
+	l_dword |= 0x5;
+	nbmc_write_index(nb_dev, 0x91, l_dword);
+	set_nbmc_enable_bits(nb_dev, 0xb1, 0, 1 << 6);
+	set_nbmc_enable_bits(nb_dev, 0xc3, 0, 1);
+
+	/* TODO: the optimization of voltage and frequency */
+}
+
+static struct pci_operations lops_pci = {
+	.set_subsystem = pci_dev_set_subsystem,
+};
+
+static struct device_operations ht_ops = {
+	.read_resources = rs690_gfx_read_resources,
+	.set_resources = rs690_gfx_set_resources,
+	.enable_resources = pci_dev_enable_resources,
+	.init = internal_gfx_pci_dev_init,	/* The option ROM initializes the device. rs690_gfx_init, */
+	.scan_bus = 0,
+	.enable = rs690_internal_gfx_enable,
+	.ops_pci = &lops_pci,
+};
+
+static struct pci_driver internal_gfx_driver __pci_driver = {
+	.ops = &ht_ops,
+	.vendor = PCI_VENDOR_ID_ATI,
+	.device = PCI_DEVICE_ID_ATI_RS690MT_INT_GFX,
+};
+
+/* step 12 ~ step 14 from rpr */
+static void single_port_configuration(device_t nb_dev, device_t dev)
+{
+	u8 result, width;
+	u32 reg32;
+	struct southbridge_amd_rs690_config *cfg =
+	    (struct southbridge_amd_rs690_config *)nb_dev->chip_info;
+
+	printk_info("rs690_gfx_init single_port_configuration.\n");
+
+	/* step 12 training, releases hold training for GFX port 0 (device 2) */
+	set_nbmisc_enable_bits(nb_dev, 0x8, 1 << 4, 0<<4);
+	PcieReleasePortTraining(nb_dev, dev, 2);
+	result = PcieTrainPort(nb_dev, dev, 2);
+	printk_info("rs690_gfx_init single_port_configuration step12.\n");
+
+	/* step 13 Power Down Control */
+	/* step 13.1 Enables powering down transmitter and receiver pads along with PLL macros. */
+	set_pcie_enable_bits(nb_dev, 0x40, 1 << 0, 1 << 0);
+
+	/* step 13.a Link Training was NOT successful */
+	if (!result) {
+		set_nbmisc_enable_bits(nb_dev, 0x8, 0, 0x3 << 4); /* prevent from training. */
+		set_nbmisc_enable_bits(nb_dev, 0xc, 0, 0x3 << 2); /* hide the GFX bridge. */
+		if (cfg->gfx_tmds)
+			nbpcie_ind_write_index(nb_dev, 0x65, 0xccf0f0);
+		else {
+			nbpcie_ind_write_index(nb_dev, 0x65, 0xffffffff);
+			set_nbmisc_enable_bits(nb_dev, 0x7, 1 << 3, 1 << 3);
+		}
+	} else {		/* step 13.b Link Training was successful */
+
+		reg32 = nbpcie_p_read_index(dev, 0xa2);
+		width = (reg32 >> 4) & 0x7;
+		printk_debug("GFX LC_LINK_WIDTH = 0x%x.\n", width);
+		switch (width) {
+		case 1:
+		case 2:
+			nbpcie_ind_write_index(nb_dev, 0x65,
+					       cfg->gfx_lane_reversal ? 0x7f7f : 0xccfefe);
+			break;
+		case 4:
+			nbpcie_ind_write_index(nb_dev, 0x65,
+					       cfg->gfx_lane_reversal ? 0x3f3f : 0xccfcfc);
+			break;
+		case 8:
+			nbpcie_ind_write_index(nb_dev, 0x65,
+					       cfg->gfx_lane_reversal ? 0x0f0f : 0xccf0f0);
+			break;
+		}
+	}
+	printk_info("rs690_gfx_init single_port_configuration step13.\n");
+
+	/* step 14 Reset Enumeration Timer, disables the shortening of the enumeration timer */
+	set_pcie_enable_bits(dev, 0x70, 1 << 19, 0 << 19);
+	printk_info("rs690_gfx_init single_port_configuration step14.\n");
+}
+
+/* step 15 ~ step 18 from rpr */
+static void dual_port_configuration(device_t nb_dev, device_t dev)
+{
+	u8 result, width;
+	u32 reg32;
+	struct southbridge_amd_rs690_config *cfg =
+		    (struct southbridge_amd_rs690_config *)nb_dev->chip_info;
+
+	/* step 15: Training for Device 2 */
+	set_nbmisc_enable_bits(nb_dev, 0x8, 1 << 4, 0 << 4);
+	/* Releases hold training for GFX port 0 (device 2) */
+	PcieReleasePortTraining(nb_dev, dev, 2);
+	/* PCIE Link Training Sequence */
+	result = PcieTrainPort(nb_dev, dev, 2);
+
+	/* step 16: Power Down Control for Device 2 */
+	/* step 16.a Link Training was NOT successful */
+	if (!result) {
+		/* Powers down all lanes for port A */
+		nbpcie_ind_write_index(nb_dev, 0x65, 0x0f0f);
+	} else {		/* step 16.b Link Training was successful */
+
+		reg32 = nbpcie_p_read_index(dev, 0xa2);
+		width = (reg32 >> 4) & 0x7;
+		printk_debug("GFX LC_LINK_WIDTH = 0x%x.\n", width);
+		switch (width) {
+		case 1:
+		case 2:
+			nbpcie_ind_write_index(nb_dev, 0x65,
+					       cfg->gfx_lane_reversal ? 0x0707 : 0x0e0e);
+			break;
+		case 4:
+			nbpcie_ind_write_index(nb_dev, 0x65,
+					       cfg->gfx_lane_reversal ? 0x0303 : 0x0c0c);
+			break;
+		}
+	}
+
+	/* step 17: Training for Device 3 */
+	set_nbmisc_enable_bits(nb_dev, 0x8, 1 << 5, 0 << 5);
+	/* Releases hold training for GFX port 0 (device 3) */
+	PcieReleasePortTraining(nb_dev, dev, 3);
+	/* PCIE Link Training Sequence */
+	result = PcieTrainPort(nb_dev, dev, 3);
+
+	/*step 18: Power Down Control for Device 3 */
+	/* step 18.a Link Training was NOT successful */
+	if (!result) {
+		/* Powers down all lanes for port B and PLL1 */
+		nbpcie_ind_write_index(nb_dev, 0x65, 0xccf0f0);
+	} else {		/* step 18.b Link Training was successful */
+
+		reg32 = nbpcie_p_read_index(dev, 0xa2);
+		width = (reg32 >> 4) & 0x7;
+		printk_debug("GFX LC_LINK_WIDTH = 0x%x.\n", width);
+		switch (width) {
+		case 1:
+		case 2:
+			nbpcie_ind_write_index(nb_dev, 0x65,
+					       cfg->gfx_lane_reversal ? 0x7070 : 0xe0e0);
+			break;
+		case 4:
+			nbpcie_ind_write_index(nb_dev, 0x65,
+					       cfg->gfx_lane_reversal ? 0x3030 : 0xc0c0);
+			break;
+		}
+	}
+}
+
+
+/* For single port GFX configuration Only 
+* width:
+* 	000 = x16
+* 	001 = x1
+*	010 = x2
+*	011 = x4
+*	100 = x8
+*	101 = x12 (not supported)
+*	110 = x16
+*/
+static void dynamic_link_width_control(device_t nb_dev, device_t dev, u8 width)
+{
+	u32 reg32;
+	device_t sb_dev;
+	struct southbridge_amd_rs690_config *cfg =
+	    (struct southbridge_amd_rs690_config *)nb_dev->chip_info;
+
+	/* step 5.9.1.1 */
+	reg32 = nbpcie_p_read_index(dev, 0xa2);
+
+	/* step 5.9.1.2 */
+	set_pcie_enable_bits(nb_dev, 0x40, 1 << 0, 1 << 0);
+	/* step 5.9.1.3 */
+	set_pcie_enable_bits(dev, 0xa2, 3 << 0, width << 0);
+	/* step 5.9.1.4 */
+	set_pcie_enable_bits(dev, 0xa2, 1 << 8, 1 << 8);
+	/* step 5.9.2.4 */
+	if (0 == cfg->gfx_reconfiguration)
+		set_pcie_enable_bits(dev, 0xa2, 1 << 11, 1 << 11);
+
+	/* step 5.9.1.5 */
+	do {
+		reg32 = nbpcie_p_read_index(dev, 0xa2);
+	}
+	while (reg32 & 0x100);
+
+	/* step 5.9.1.6 */
+	sb_dev = dev_find_slot(0, PCI_DEVFN(8, 0));
+	do {
+		reg32 = pci_ext_read_config32(nb_dev, sb_dev,
+					  PCIE_VC0_RESOURCE_STATUS);
+	} while (reg32 & VC_NEGOTIATION_PENDING);
+
+	/* step 5.9.1.7 */
+	reg32 = nbpcie_p_read_index(dev, 0xa2);
+	if (((reg32 & 0x70) >> 4) != 0x6) {
+		/* the unused lanes should be powered off. */
+	}
+
+	/* step 5.9.1.8 */
+	set_pcie_enable_bits(nb_dev, 0x40, 1 << 0, 0 << 0);
+}
+
+/*
+* GFX Core initialization, dev2, dev3
+*/
+void rs690_gfx_init(device_t nb_dev, device_t dev, u32 port)
+{
+	u16 reg16;
+	struct southbridge_amd_rs690_config *cfg =
+	    (struct southbridge_amd_rs690_config *)nb_dev->chip_info;
+
+	printk_info("rs690_gfx_init, nb_dev=0x%x, dev=0x%x, port=0x%x.\n",
+		    nb_dev, dev, port);
+
+	/* step 0, REFCLK_SEL, skip A11 revision */
+	set_nbmisc_enable_bits(nb_dev, 0x6a, 1 << 9,
+			       cfg->gfx_dev2_dev3 ? 1 << 9 : 0 << 9);
+	printk_info("rs690_gfx_init step0.\n");
+
+	/* step 1, lane reversal (only need if CMOS option is enabled) */
+	if (cfg->gfx_lane_reversal) {
+		set_nbmisc_enable_bits(nb_dev, 0x33, 1 << 2, 1 << 2);
+		if (cfg->gfx_dual_slot)
+			set_nbmisc_enable_bits(nb_dev, 0x33, 1 << 3, 1 << 3);
+	}
+	printk_info("rs690_gfx_init step1.\n");
+
+	/* step 1.1, dual-slot gfx configuration (only need if CMOS option is enabled) */
+	/* AMD calls the configuration CrossFire */
+	if (cfg->gfx_dual_slot)
+		set_nbmisc_enable_bits(nb_dev, 0x0, 0xf << 8, 5 << 8);
+	printk_info("rs690_gfx_init step2.\n");
+
+	/* step 2, TMDS, (only need if CMOS option is enabled) */
+	if (cfg->gfx_tmds) {
+	}
+
+	/* step 3, GFX overclocking, (only need if CMOS option is enabled) */
+	/* skip */
+
+	/* step 4, reset the GFX link */
+	/* step 4.1 asserts both calibration reset and global reset */
+	set_nbmisc_enable_bits(nb_dev, 0x8, 0x3 << 14, 0x3 << 14);
+
+	/* step 4.2 de-asserts calibration reset */
+	set_nbmisc_enable_bits(nb_dev, 0x8, 1 << 14, 0 << 14);
+
+	/* step 4.3 wait for at least 200us */
+	udelay(200);
+
+	/* step 4.4 de-asserts global reset */
+	set_nbmisc_enable_bits(nb_dev, 0x8, 1 << 15, 0 << 15);
+
+	/* step 4.5 asserts both calibration reset and global reset */
+	/* a weird step in RPR, don't do that */
+	/* set_nbmisc_enable_bits(nb_dev, 0x8, 0x3 << 14, 0x3 << 14); */
+
+	/* step 4.6 bring external GFX device out of reset, wait for 1ms */
+	mdelay(1);
+	printk_info("rs690_gfx_init step4.\n");
+
+	/* step 5 program PCIE memory mapped configuration space */
+	/* done by enable_pci_bar3() before */
+
+	/* step 6 SBIOS compile flags */
+
+	/* step 7 compliance state, (only need if CMOS option is enabled) */
+	/* the compliance stete is just for test. refer to 4.2.5.2 of PCIe specification */
+	if (cfg->gfx_compliance) {
+		/* force compliance */
+		set_nbmisc_enable_bits(nb_dev, 0x32, 1 << 6, 1 << 6);
+		/* release hold training for device 2. GFX initialization is done. */
+		set_nbmisc_enable_bits(nb_dev, 0x8, 1 << 4, 0 << 4);
+		dynamic_link_width_control(nb_dev, dev, cfg->gfx_link_width);
+		printk_info("rs690_gfx_init step7.\n");
+		return;
+	}
+
+	/* step 8 common initialization */
+	/* step 8.1 sets RCB timeout to be 25ms */
+	set_pcie_enable_bits(dev, 0x70, 7 << 16, 3 << 16);
+	printk_info("rs690_gfx_init step8.1.\n");
+
+	/* step 8.2 disables slave ordering logic */
+	set_pcie_enable_bits(nb_dev, 0x20, 1 << 8, 1 << 8);
+	printk_info("rs690_gfx_init step8.2.\n");
+
+	/* step 8.3 sets DMA payload size to 64 bytes */
+	set_pcie_enable_bits(nb_dev, 0x10, 7 << 10, 4 << 10);
+	printk_info("rs690_gfx_init step8.3.\n");
+
+	/* step 8.4 if the LTSSM could not see all 8 TS1 during Polling Active, it can still 
+	 * time out and go back to Detect Idle.*/
+	set_pcie_enable_bits(dev, 0x02, 1 << 14, 1 << 14);
+	printk_info("rs690_gfx_init step8.4.\n");
+
+	/* step 8.5 shortens the enumeration timer */
+	set_pcie_enable_bits(dev, 0x70, 1 << 19, 1 << 19);
+	printk_info("rs690_gfx_init step8.5.\n");
+
+	/* step 8.6 blocks DMA traffic during C3 state */
+	set_pcie_enable_bits(dev, 0x10, 1 << 0, 0 << 0);
+	printk_info("rs690_gfx_init step8.6.\n");
+
+	/* step 8.7 Do not gate the electrical idle form the PHY
+	 * step 8.8 Enables the escape from L1L23 */
+	set_pcie_enable_bits(dev, 0xa0, 3 << 30, 3 << 30);
+	printk_info("rs690_gfx_init step8.8.\n");
+
+	/* step 8.9 Setting this register to 0x1 will workaround a PCI Compliance failure reported by Vista DTM. 
+	 * SLOT_IMPLEMENTED at PCIE_CAP */
+	reg16 = pci_read_config16(dev, 0x5a);
+	reg16 |= 0x100;
+	pci_write_config16(dev, 0x5a, reg16);
+	printk_info("rs690_gfx_init step8.9.\n");
+
+	/* step 8.10 Setting this register to 0x1 will hide the Advanced Error Rporting Capabilities in the PCIE Brider.
+	 * This will workaround several failures reported by the PCI Compliance test under Vista DTM. */
+	set_nbmisc_enable_bits(nb_dev, 0x33, 1 << 31, 0 << 31);
+	printk_info("rs690_gfx_init step8.10.\n");
+
+	/* step 8.11 Sets REGS_DLP_IGNORE_IN_L1_EN to ignore DLLPs during L1 so that txclk can be turned off. */
+	set_pcie_enable_bits(nb_dev, 0x02, 1 << 0, 1 << 0);
+	printk_info("rs690_gfx_init step8.11.\n");
+
+	/* step 8.12 Sets REGS_LC_DONT_GO_TO_L0S_IF_L1_ARMED to prevent lc to go to from L0 to Rcv_L0s if L1 is armed. */
+	set_pcie_enable_bits(nb_dev, 0x02, 1 << 6, 1 << 6);
+	printk_info("rs690_gfx_init step8.12.\n");
+
+	/* step 8.13 Sets CMGOOD_OVERRIDE. */
+	set_nbmisc_enable_bits(nb_dev, 0x6a, 1 << 17, 1 << 17);
+	printk_info("rs690_gfx_init step8.13.\n");
+
+	/* step 9 Enable TLP Flushing, for non-AMD GFX devices and Hot-Plug devices only. */
+	/* skip */
+
+	/* step 10 Optional Features, only needed if CMOS option is enabled. */
+	/* step 10.a: L0s */
+	/* enabling L0s in the RS690 GFX port(s) */
+	set_pcie_enable_bits(nb_dev, 0xF9, 3 << 13, 2 << 13);
+	set_pcie_enable_bits(dev, 0xA0, 0xf << 8, 8 << 8);
+	reg16 = pci_read_config16(dev, 0x68);
+	reg16 |= 1 << 0;
+	/* L0s is intended as a power saving state */
+	/* pci_write_config16(dev, 0x68, reg16); */
+
+	/* enabling L0s in the External GFX Device(s) */
+
+	/* step 10.b: active state power management (ASPM L1) */
+	/* TO DO */
+
+	/* step 10.c: turning off PLL During L1/L23 */
+	set_pcie_enable_bits(nb_dev, 0x40, 1 << 3, 1 << 3);
+	set_pcie_enable_bits(nb_dev, 0x40, 1 << 9, 1 << 9);
+
+	/* step 10.d: TXCLK clock gating */
+	set_nbmisc_enable_bits(nb_dev, 0x7, 3, 3);
+	set_nbmisc_enable_bits(nb_dev, 0x7, 1 << 22, 1 << 22);
+	set_pcie_enable_bits(nb_dev, 0x11, 0xf << 4, 0xc << 4);
+
+	/* step 10.e: LCLK clock gating, done in rs690_config_misc_clk() */
+
+	/* step 11 Poll GPIO to determine whether it is single-port or dual-port configuration.  
+	 * While details will be added later in the document, for now assue the single-port configuration. */
+	/* skip */
+
+	/* Single-port/Dual-port configureation. */
+	switch (cfg->gfx_dual_slot) {
+	case 0:
+		single_port_configuration(nb_dev, dev);
+		break;
+	case 1:
+		dual_port_configuration(nb_dev, dev);
+		break;
+	default:
+		printk_info("Incorrect configuration of external gfx slot.\n");
+		break;
+	}
+}

Added: trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_ht.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_ht.c	                        (rev 0)
+++ trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_ht.c	2008-09-22 13:07:20 UTC (rev 3588)
@@ -0,0 +1,90 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "rs690.h"
+
+/* for UMA internal graphics */
+void avoid_lpc_dma_deadlock(device_t nb_dev, device_t sb_dev)
+{
+	device_t k8_f0;
+	u8 reg;
+
+	k8_f0 = dev_find_slot(0, PCI_DEVFN(0x18, 0));
+	set_nbcfg_enable_bits(k8_f0, 0x68, 3 << 21, 1 << 21);
+
+	reg = nbpcie_p_read_index(sb_dev, 0x10);
+	reg |= 0x100;		/* bit9=1 */
+	nbpcie_p_write_index(sb_dev, 0x10, reg);
+
+	reg = nbpcie_p_read_index(nb_dev, 0x10);
+	reg |= 0x100;		/* bit9=1 */
+	nbpcie_p_write_index(nb_dev, 0x10, reg);
+
+	/* Enable NP protocol over PCIE for memory-mapped writes targeting LPC
+	 * Set this bit to avoid a deadlock condition. */
+	reg = htiu_read_index(nb_dev, 0x6);
+	reg |= 0x1000000;	/* bit26 */
+	htiu_write_index(nb_dev, 0x6, reg);
+}
+
+static void pcie_init(struct device *dev)
+{
+	/* Enable pci error detecting */
+	u32 dword;
+
+	printk_info("pcie_init in rs690_ht.c\n");
+
+	/* System error enable */
+	dword = pci_read_config32(dev, 0x04);
+	dword |= (1 << 8);	/* System error enable */
+	dword |= (1 << 30);	/* Clear possible errors */
+	pci_write_config32(dev, 0x04, dword);
+
+	/* 
+	 * 1 is APIC enable
+	 * 18 is enable nb to accept A4 interrupt request from SB.
+	 */
+	dword = pci_read_config32(dev, 0x4C);
+	dword |= 1 << 1 | 1 << 18;	/* Clear possible errors */
+	pci_write_config32(dev, 0x4C, dword);
+}
+
+static struct pci_operations lops_pci = {
+	.set_subsystem = pci_dev_set_subsystem,
+};
+
+static struct device_operations ht_ops = {
+	.read_resources = pci_dev_read_resources,
+	.set_resources = pci_dev_set_resources,
+	.enable_resources = pci_dev_enable_resources,
+	.init = pcie_init,
+	.scan_bus = 0,
+	.ops_pci = &lops_pci,
+};
+
+static struct pci_driver ht_driver __pci_driver = {
+	.ops = &ht_ops,
+	.vendor = PCI_VENDOR_ID_ATI,
+	.device = PCI_DEVICE_ID_ATI_RS690_HT,
+};

Added: trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_pcie.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_pcie.c	                        (rev 0)
+++ trunk/coreboot-v2/src/southbridge/amd/rs690/rs690_pcie.c	2008-09-22 13:07:20 UTC (rev 3588)
@@ -0,0 +1,422 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <delay.h>
+#include "rs690.h"
+
+/*------------------------------------------------
+* Global variable
+------------------------------------------------*/
+PCIE_CFG AtiPcieCfg = {
+	PCIE_ENABLE_STATIC_DEV_REMAP,	/* Config */
+	0,			/* ResetReleaseDelay */
+	0,			/* Gfx0Width */
+	0,			/* Gfx1Width */
+	0,			/* GfxPayload */
+	0,			/* GppPayload */
+	0,			/* PortDetect, filled by GppSbInit */
+	0,			/* PortHp */
+	0,			/* DbgConfig */
+	0,			/* DbgConfig2 */
+	0,			/* GfxLx */
+	0,			/* GppLx */
+	0,			/* NBSBLx */
+	0,			/* PortSlotInit */
+	0,			/* Gfx0Pwr */
+	0,			/* Gfx1Pwr */
+	0			/* GppPwr */
+};
+
+static void PciePowerOffGppPorts(device_t nb_dev, device_t dev, u32 port);
+static void ValidatePortEn(device_t nb_dev);
+
+static void ValidatePortEn(device_t nb_dev)
+{
+}
+
+
+/*****************************************************************
+* Compliant with CIM_33's PCIEPowerOffGppPorts
+* Power off unused GPP lines
+*****************************************************************/
+static void PciePowerOffGppPorts(device_t nb_dev, device_t dev, u32 port)
+{
+	u32 reg;
+	u16 state_save;
+	struct southbridge_amd_rs690_config *cfg =
+	    (struct southbridge_amd_rs690_config *)nb_dev->chip_info;
+	u8 state = cfg->port_enable;
+
+	if (!(AtiPcieCfg.Config & PCIE_DISABLE_HIDE_UNUSED_PORTS))
+		state &= AtiPcieCfg.PortDetect;
+	state = ~state;
+	state &= (1 << 4) + (1 << 5) + (1 << 6) + (1 << 7);
+	state_save = state << 17;
+	state &= !(AtiPcieCfg.PortHp);
+	reg = nbmisc_read_index(nb_dev, 0x0c);
+	reg |= state;
+	nbmisc_write_index(nb_dev, 0x0c, reg);
+
+	reg = nbmisc_read_index(nb_dev, 0x08);
+	reg |= state_save;
+	nbmisc_write_index(nb_dev, 0x08, reg);
+
+	if ((AtiPcieCfg.Config & PCIE_OFF_UNUSED_GPP_LANES)
+	    && !(AtiPcieCfg.
+		 Config & (PCIE_DISABLE_HIDE_UNUSED_PORTS +
+			   PCIE_GFX_COMPLIANCE))) {
+	}
+	/* step 3 Power Down Control for Southbridge */
+	reg = nbpcie_p_read_index(dev, 0xa2);
+
+	switch ((reg >> 4) & 0x7) {	/* get bit 4-6, LC_LINK_WIDTH_RD */
+	case 1:
+		nbpcie_ind_write_index(nb_dev, 0x65, 0x0e0e);
+		break;
+	case 2:
+		nbpcie_ind_write_index(nb_dev, 0x65, 0x0c0c);
+		break;
+	default:
+		break;
+	}
+}
+
+static void pcie_init(struct device *dev)
+{
+	/* Enable pci error detecting */
+	u32 dword;
+
+	printk_debug("pcie_init in rs690_pcie.c\n");
+
+	/* System error enable */
+	dword = pci_read_config32(dev, 0x04);
+	dword |= (1 << 8);	/* System error enable */
+	dword |= (1 << 30);	/* Clear possible errors */
+	pci_write_config32(dev, 0x04, dword);
+}
+
+static struct pci_operations lops_pci = {
+	.set_subsystem = 0,
+};
+
+static struct device_operations pcie_ops = {
+	.read_resources = pci_bus_read_resources,
+	.set_resources = pci_dev_set_resources,
+	.enable_resources = pci_bus_enable_resources,
+	.init = pcie_init,
+	.scan_bus = pci_scan_bridge,
+	/*.enable           = rs690_enable, */
+	.ops_pci = &lops_pci,
+};
+
+static struct pci_driver pcie_driver __pci_driver = {
+	.ops = &pcie_ops,
+	.vendor = PCI_VENDOR_ID_ATI,
+	.device = PCI_DEVICE_ID_ATI_RS690_PCIE,
+};
+
+static struct pci_driver pcie_driver_dev7 __pci_driver = {
+	.ops = &pcie_ops,
+	.vendor = PCI_VENDOR_ID_ATI,
+	.device = PCI_DEVICE_ID_ATI_RS690_PCIE_DEV7,
+};
+static struct pci_driver pcie_driver_dev8 __pci_driver = {
+	.ops = &pcie_ops,
+	.vendor = PCI_VENDOR_ID_ATI,
+	.device = PCI_DEVICE_ID_ATI_RS690_PCIE_DEV8,
+};
+
+/**********************************************************************
+**********************************************************************/
+static void switching_gpp_configurations(device_t nb_dev, device_t sb_dev)
+{
+	u32 reg;
+	struct southbridge_amd_rs690_config *cfg =
+	    (struct southbridge_amd_rs690_config *)nb_dev->chip_info;
+
+	/* enables GPP reconfiguration */
+	reg = nbmisc_read_index(nb_dev, PCIE_NBCFG_REG7);
+	reg |=
+	    (RECONFIG_GPPSB_EN + RECONFIG_GPPSB_LINK_CONFIG +
+	     RECONFIG_GPPSB_ATOMIC_RESET);
+	nbmisc_write_index(nb_dev, PCIE_NBCFG_REG7, reg);
+
+	/* sets desired GPPSB configurations, bit4-7 */
+	reg = nbmisc_read_index(nb_dev, 0x67);
+	reg &= 0xff0f;		/* clean */
+	reg |= cfg->gpp_configuration;
+	nbmisc_write_index(nb_dev, 0x67, reg);
+
+	/* read bit14 and write back its inverst value */
+	reg = nbmisc_read_index(nb_dev, PCIE_NBCFG_REG7);
+	reg ^= RECONFIG_GPPSB_GPPSB;
+	nbmisc_write_index(nb_dev, PCIE_NBCFG_REG7, reg);
+
+	/* delay 1ms */
+	mdelay(1);
+
+	/* waits until SB has trained to L0, poll for bit0-5 = 0x10 */
+	do {
+		reg = nbpcie_p_read_index(sb_dev, PCIE_LC_STATE0);
+		reg &= 0x1f;	/* remain LSB 5 bits */
+	} while (LC_STATE_RECONFIG_GPPSB != reg);
+
+	/* ensures that virtual channel negotiation is completed. poll for bit1 = 0 */
+	do {
+		reg =
+		    pci_ext_read_config32(nb_dev, sb_dev,
+					  PCIE_VC0_RESOURCE_STATUS);
+	} while (reg & VC_NEGOTIATION_PENDING);
+}
+
+/*****************************************************************
+* The rs690 uses NBCONFIG:0x1c (BAR3) to map the PCIE Extended Configuration
+* Space to a 256MB range within the first 4GB of addressable memory.
+*****************************************************************/
+void enable_pcie_bar3(device_t nb_dev)
+{
+	printk_debug("enable_pcie_bar3()\n");
+	set_nbcfg_enable_bits(nb_dev, 0x7C, 1 << 30, 1 << 30);	/* Enables writes to the BAR3 register. */
+	set_nbcfg_enable_bits(nb_dev, 0x84, 7 << 16, 0 << 16);
+
+	pci_write_config32(nb_dev, 0x1C, EXT_CONF_BASE_ADDRESS);	/* PCIEMiscInit */
+	pci_write_config32(nb_dev, 0x20, 0x00000000);
+	set_htiu_enable_bits(nb_dev, 0x32, 1 << 28, 1 << 28);	/* PCIEMiscInit */
+	ProgK8TempMmioBase(1, EXT_CONF_BASE_ADDRESS, TEMP_MMIO_BASE_ADDRESS);
+}
+
+/*****************************************************************
+* We should disable bar3 when we want to exit rs690_enable, because bar3 will be
+* remapped in set_resource later.
+*****************************************************************/
+void disable_pcie_bar3(device_t nb_dev)
+{
+	printk_debug("disable_pcie_bar3()\n");
+	set_nbcfg_enable_bits(nb_dev, 0x7C, 1 << 30, 0 << 30);	/* Disable writes to the BAR3. */
+	pci_write_config32(nb_dev, 0x1C, 0);	/* clear BAR3 address */
+	ProgK8TempMmioBase(0, EXT_CONF_BASE_ADDRESS, TEMP_MMIO_BASE_ADDRESS);
+}
+
+/*****************************************
+* Compliant with CIM_33's PCIEGPPInit
+* nb_dev:
+*	root bridge struct
+* dev:
+*	p2p bridge struct
+* port:
+*	p2p bridge number, 4-8
+*****************************************/
+void rs690_gpp_sb_init(device_t nb_dev, device_t dev, u32 port)
+{
+	u8 reg8;
+	u16 reg16;
+	device_t sb_dev;
+	struct southbridge_amd_rs690_config *cfg =
+	    (struct southbridge_amd_rs690_config *)nb_dev->chip_info;
+	printk_debug("gpp_sb_init nb_dev=0x%x, dev=0x%x, port=0x%x\n", nb_dev, dev, port);
+
+	/* init GPP core */
+	set_pcie_enable_bits(nb_dev, 0x20 | PCIE_CORE_INDEX_GPPSB, 1 << 8,
+			     1 << 8);
+	/* PCIE initialization 5.10.2: rpr 2.12*/
+	set_pcie_enable_bits(nb_dev, 0x02 | PCIE_CORE_INDEX_GPPSB, 1 << 0, 1 << 0);	/* no description in datasheet. */
+
+	/* init GPPSB port */
+	/* Sets RCB timeout to be 100ms by setting bits[18:16] to 3 b101 and shortens the enumeration timer by setting bit[19] to 0*/
+	set_pcie_enable_bits(dev, 0x70, 7 << 16, 0xd << 16);
+	/* PCIE initialization 5.10.2: rpr 2.4 */
+	set_pcie_enable_bits(dev, 0x02, ~0xffffffff, 1 << 14);
+	/* Do not gate the electrical idle from the PHY and enables the escape from L1L23 */
+	set_pcie_enable_bits(dev, 0xA0, ~0xffffffbf, (3 << 30) | (3 << 12) | (3 << 4));
+	/* PCIE initialization 5.10.2: rpr 2.13 */
+	set_pcie_enable_bits(dev, 0x02, ~0xffffffff, 1 << 6);
+
+	/* SLOT_IMPLEMENTED in pcieConfig space */
+	reg8 = pci_read_config8(dev, 0x5b);
+	reg8 |= 1 << 0;
+	pci_write_config8(dev, 0x5b, reg8);
+
+	reg16 = pci_read_config16(dev, 0x5a);
+	reg16 |= 0x100;
+	pci_write_config16(dev, 0x5a, reg16);
+	nbmisc_write_index(nb_dev, 0x34, 0);
+
+	/* check compliance rpr step 2.1*/
+	if (AtiPcieCfg.Config & PCIE_GPP_COMPLIANCE) {
+		u32 tmp;
+		tmp = nbmisc_read_index(nb_dev, 0x67);
+		tmp |= 1 << 3;
+		nbmisc_write_index(nb_dev, 0x67, tmp);
+	}
+
+	/* step 5: dynamic slave CPL buffer allocation */
+	set_pcie_enable_bits(dev, 0x20, 1 << 11, 1 << 11);
+
+	/* step 5a: Training for GPP devices */
+	/* init GPP */
+	switch (port) {
+	case 4:		/* GPP */
+	case 5:
+	case 6:
+	case 7:
+		/* Blocks DMA traffic during C3 state */
+		set_pcie_enable_bits(dev, 0x10, 1 << 0, 0 << 0);
+		/* Enabels TLP flushing */
+		set_pcie_enable_bits(dev, 0x20, 1 << 19, 0 << 19);
+
+		/* check port enable */
+		if (cfg->port_enable & (1 << port)) {
+			PcieReleasePortTraining(nb_dev, dev, port);
+			if (!(AtiPcieCfg.Config & PCIE_GPP_COMPLIANCE)) {
+				u8 res = PcieTrainPort(nb_dev, dev, port);
+				printk_debug("PcieTrainPort port=0x%x result=%d\n", port, res);
+				if (res) {
+					AtiPcieCfg.PortDetect |= 1 << port;
+				}
+			}
+		}
+		break;
+	case 8:		/* SB */
+		break;
+	}
+	PciePowerOffGppPorts(nb_dev, dev, port);
+
+	/* step 5b: GFX devices in a GPP slot */
+
+	/* step 6a: VCI */
+	sb_dev = dev_find_slot(0, PCI_DEVFN(8, 0));
+	if (port == 8) {
+		/* Clear bits 7:1 */
+		pci_ext_write_config32(nb_dev, sb_dev, 0x114, 0x3f << 1, 0 << 1);
+		/* Maps Traffic Class 1-7 to VC1 */
+		pci_ext_write_config32(nb_dev, sb_dev, 0x120, 0x7f << 1, 0x7f << 1);
+		/* Assigns VC ID to 1 */
+		pci_ext_write_config32(nb_dev, sb_dev, 0x120, 7 << 24, 1 << 24);
+		/* Enables VC1 */
+		pci_ext_write_config32(nb_dev, sb_dev, 0x120, 1 << 31, 1 << 31);
+#if 0
+		do {
+			reg16 = pci_ext_read_config32(nb_dev, sb_dev, 0x124);
+			reg16 &= 0x2;
+		} while (reg16); /*bit[1] = 0 means VC1 flow control initialization is successful */
+#endif
+	}
+
+	/* step 6b: L0s for the southbridge link */
+	/* To enalbe L0s in the southbridage*/
+
+	/* step 6c: L0s for the GPP link(s) */
+	/* To eable L0s in the RS690 for the GPP port(s) */
+	set_pcie_enable_bits(nb_dev, 0xf9, 3 << 13, 2 << 13);
+	set_pcie_enable_bits(dev, 0xa0, 0xf << 8, 0x9 << 8);
+	reg16 = pci_read_config16(dev, 0x68);
+	reg16 |= 1 << 0;
+	pci_write_config16(dev, 0x68, reg16);
+
+	/* step 6d: ASPM L1 for the southbridge link */
+	/* To enalbe L1s in the southbridage*/
+
+	/* step 6e: ASPM L1 for GPP link(s) */;
+	set_pcie_enable_bits(nb_dev, 0xf9, 3 << 13, 2 << 13);
+	set_pcie_enable_bits(dev, 0xa0, 3 << 12, 3 << 12);
+	set_pcie_enable_bits(dev, 0xa0, 0xf << 4, 3 << 4);
+	reg16 = pci_read_config16(dev, 0x68);
+	reg16 &= ~0xff;
+	reg16 |= 1 << 1;
+	pci_write_config16(dev, 0x68, reg16);
+
+	/* step 6f: Turning off PLL during L1/L23 */
+	set_pcie_enable_bits(nb_dev, 0x40, 1 << 3, 1 << 3);
+	set_pcie_enable_bits(nb_dev, 0x40, 1 << 9, 1 << 9);
+
+	/* step 6g: TXCLK clock gating */
+	set_nbmisc_enable_bits(nb_dev, 0x7, 3 << 4, 3 << 4);
+	set_nbmisc_enable_bits(nb_dev, 0x7, 1 << 22, 1 << 22);
+	set_pcie_enable_bits(nb_dev, 0x11, 0xf << 4, 0xc << 4);
+
+	/* step 6h: LCLK clock gating, done in rs690_config_misc_clk() */
+}
+
+/*****************************************
+* Compliant with CIM_33's PCIEConfigureGPPCore
+*****************************************/
+void config_gpp_core(device_t nb_dev, device_t sb_dev)
+{
+	u32 reg;
+	struct southbridge_amd_rs690_config *cfg =
+	    (struct southbridge_amd_rs690_config *)nb_dev->chip_info;
+
+	reg = nbmisc_read_index(nb_dev, 0x20);
+	if (AtiPcieCfg.Config & PCIE_ENABLE_STATIC_DEV_REMAP)
+		reg &= 0xfffffffd;	/* set bit1 = 0 */
+	else
+		reg |= 0x2;	/* set bit1 = 1 */
+	nbmisc_write_index(nb_dev, 0x20, reg);
+
+	reg = nbmisc_read_index(nb_dev, 0x67);	/* get STRAP_BIF_LINK_CONFIG_GPPSB at bit 4-7 */
+	if (cfg->gpp_configuration != ((reg >> 4) & 0xf))
+		switching_gpp_configurations(nb_dev, sb_dev);
+	ValidatePortEn(nb_dev);
+}
+
+/*****************************************
+* Compliant with CIM_33's PCIEMiscClkProg
+*****************************************/
+void pcie_config_misc_clk(device_t nb_dev)
+{
+	u32 reg;
+	struct bus pbus; /* fake bus for dev0 fun1 */
+
+	reg = pci_read_config32(nb_dev, 0x4c);
+	reg |= 1 << 0;
+	pci_write_config32(nb_dev, 0x4c, reg);
+
+	if (AtiPcieCfg.Config & PCIE_GFX_CLK_GATING) {
+		/* TXCLK Clock Gating */
+		set_nbmisc_enable_bits(nb_dev, 0x07, 3 << 0, 3 << 0);
+		set_nbmisc_enable_bits(nb_dev, 0x07, 1 << 22, 1 << 22);
+		set_pcie_enable_bits(nb_dev, 0x11 | PCIE_CORE_INDEX_GFX, (3 << 6) | (~0xf), 3 << 6);
+
+		/* LCLK Clock Gating */
+		reg =  pci_cf8_conf1.read32(&pbus, 0, 1, 0x94);
+		reg &= ~(1 << 16);
+		pci_cf8_conf1.write32(&pbus, 0, 1, 0x94, reg);
+	}
+
+	if (AtiPcieCfg.Config & PCIE_GPP_CLK_GATING) {
+		/* TXCLK Clock Gating */
+		set_nbmisc_enable_bits(nb_dev, 0x07, 3 << 4, 3 << 4);
+		set_nbmisc_enable_bits(nb_dev, 0x07, 1 << 22, 1 << 22);
+		set_pcie_enable_bits(nb_dev, 0x11 | PCIE_CORE_INDEX_GPPSB, (3 << 6) | (~0xf), 3 << 6);
+
+		/* LCLK Clock Gating */
+		reg =  pci_cf8_conf1.read32(&pbus, 0, 1, 0x94);
+		reg &= ~(1 << 24);
+		pci_cf8_conf1.write32(&pbus, 0, 1, 0x94, reg);
+	}
+
+	reg = pci_read_config32(nb_dev, 0x4c);
+	reg &= ~(1 << 0);
+	pci_write_config32(nb_dev, 0x4c, reg);
+}





More information about the coreboot mailing list