[coreboot] [Fwd: Re: [Fwd: Re: arima hdama problem]]

Hugh Greenberg hng at lanl.gov
Tue Oct 20 22:01:09 CEST 2009


Oops.  I did miss a big chunk of the log :).  I thought it was part of 
the previous output.  Here is the full log:


coreboot-2.3 Tue Oct 20 11:36:27 MDT 2009 starting...
Enabling routing table for node 00 done.
Enabling SMP settings
(0,1) link=01
(1,0) link=01
setup_remote_node: done
Renaming current temporary node to 01 done.
Enabling routing table for node 01 done.
02 nodes initialized.
coherent_ht_finalize
done
SBLink=00
NC node|link=00
enterinlg ahpti_co patpiimci zied_ li0n1k

pos=0x8a, unfiltered freq_cap=0x8075
pos=0x8a, filtered freq_cap=0x35
pos=0xce, unfiltered freq_cap=0x35
freq_cap1=0x35, freq_cap2=0x15
dev1 old_freq=0x0, freq=0x4, needs_reset=0x1
dev2 old_freq=0x0, freq=0x4, needs_reset=0x1
width_cap1=0x11, width_cap2=0x11
dev1 input ln_width1=0x4, ln_width2=0x4
dev1 input width=0x1
dev1 output ln_width1=0x4, ln_width2=0x4
dev1 input|output width=0x11
old dev1 input|output width=0x11
dev2 input|output width=0x11
old dev2 input|output width=0x11
entering ht_optimize_link
pos=0xd2, unfiltered freq_cap=0x35
pos=0xce, unfiltered freq_cap=0x1
pos=0xce, filtered freq_cap=0x1
freq_cap1=0x15, freq_cap2=0x1
dev1 old_freq=0x0, freq=0x0, needs_reset=0x0
dev2 old_freq=0x0, freq=0x0, needs_reset=0x0
width_cap1=0x0, width_cap2=0x0
dev1 input ln_width1=0x3, ln_width2=0x3
dev1 input width=0x0
dev1 output ln_width1=0x3, ln_width2=0x3
dev1 input|output width=0x0
old dev1 input|output width=0x0
dev2 input|output width=0x0
old dev2 input|output width=0x0
ht reset -


coreboot-2.3 Tue Oct 20 11:36:27 MDT 2009 starting...
Enabling routing table for node 00 done.
Enabling SMP settings
(0,1) link=01
(1,0) link=01
setup_remote_node: done
Renaming current temporary node to 01 done.
Enabling routing table for node 01 done.
02 nodes initialized.
coherent_ht_finalize
done
SBLink=00
NC node|link=00
iapicen taepriicn gi d ht_0o1p
 mize_link
pos=0x8a, unfiltered freq_cap=0x8075
pos=0x8a, filtered freq_cap=0x35
pos=0xce, unfiltered freq_cap=0x35
freq_cap1=0x35, freq_cap2=0x15
dev1 old_freq=0x4, freq=0x4, needs_reset=0x0
dev2 old_freq=0x4, freq=0x4, needs_reset=0x0
width_cap1=0x11, width_cap2=0x11
dev1 input ln_width1=0x4, ln_width2=0x4
dev1 input width=0x1
dev1 output ln_width1=0x4, ln_width2=0x4
dev1 input|output width=0x11
old dev1 input|output width=0x11
dev2 input|output width=0x11
old dev2 input|output width=0x11
entering ht_optimize_link
pos=0xd2, unfiltered freq_cap=0x35
pos=0xce, unfiltered freq_cap=0x1
pos=0xce, filtered freq_cap=0x1
freq_cap1=0x15, freq_cap2=0x1
dev1 old_freq=0x0, freq=0x0, needs_reset=0x0
dev2 old_freq=0x0, freq=0x0, needs_reset=0x0
width_cap1=0x0, width_cap2=0x0
dev1 input ln_width1=0x3, ln_width2=0x3
dev1 input width=0x0
dev1 output ln_width1=0x3, ln_width2=0x3
dev1 input|output width=0x0
old dev1 input|output width=0x0
dev2 input|output width=0x0
old dev2 input|output width=0x0
SMBus controller enabled
Ram1.00
setting up CPU00 northbridge registers
done.
Ram1.01
setting up CPU01 northbridge registers
done.
Ram2.00
Enabling dual channel memory
Registered
166Mhz
RAM end at 0x00100000 kB
Lower RAM end at 0x00100000 kB
Ram2.01
Enabling dual channel memory
Registered
166Mhz
RAM end at 0x00200000 kB
Lower RAM end at 0x00200000 kB
Ram3

-- 
Hugh Greenberg



Myles Watson wrote:
>
>
> On Tue, Oct 20, 2009 at 1:50 PM, Hugh Greenberg <hng at lanl.gov 
> <mailto:hng at lanl.gov>> wrote:
>
>     No, I haven't been editing the logs.  I sent you exactly what I
>     saw on the serial port.
>
> Good to know.  I didn't think you would, but there's a big chunk missing.
>
> Thanks,
> Myles
>




More information about the coreboot mailing list