[coreboot] [Fwd: Re: [Fwd: Re: arima hdama problem]]

[Hugh Greenberg]

Ok, here is the output:

coreboot-2.3 Tue Oct 20 15:20:40 MDT 2009 starting...
Enabling routing table for node 00 done.
Enabling UP settings
Disabling read/write/fill probes for UP... done.
coherent_ht_finalize
done
started ap apicid:
SBLink=00
NC node|link=00
entering ht_optimize_link
pos=0x8a, unfiltered freq_cap=0x8075
pos=0x8a, filtered freq_cap=0x35
pos=0xce, unfiltered freq_cap=0x35
freq_cap1=0x35, freq_cap2=0x15
dev1 old_freq=0x0, freq=0x4, needs_reset=0x1
dev2 old_freq=0x0, freq=0x4, needs_reset=0x1
width_cap1=0x11, width_cap2=0x11
dev1 input ln_width1=0x4, ln_width2=0x4
dev1 input width=0x1
dev1 output ln_width1=0x4, ln_width2=0x4
dev1 input|output width=0x11
old dev1 input|output width=0x11
dev2 input|output width=0x11
old dev2 input|output width=0x11
entering ht_optimize_link
pos=0xd2, unfiltered freq_cap=0x35
pos=0xce, unfiltered freq_cap=0x1
pos=0xce, filtered freq_cap=0x1
freq_cap1=0x15, freq_cap2=0x1
dev1 old_freq=0x0, freq=0x0, needs_reset=0x0
dev2 old_freq=0x0, freq=0x0, needs_reset=0x0
width_cap1=0x0, width_cap2=0x0
dev1 input ln_width1=0x3, ln_width2=0x3
dev1 input width=0x0
dev1 output ln_width1=0x3, ln_width2=0x3
dev1 input|output width=0x0
old dev1 input|output width=0x0
dev2 input|output width=0x0
old dev2 input|output width=0x0
ht reset -


coreboot-2.3 Tue Oct 20 15:20:40 MDT 2009 starting...
Enabling routing table for node 00 done.
Enabling UP settings
Disabling read/write/fill probes for UP... done.
coherent_ht_finalize
done
started ap apicid:
SBLink=00
NC node|link=00
entering ht_optimize_link
pos=0x8a, unfiltered freq_cap=0x8075
pos=0x8a, filtered freq_cap=0x35
pos=0xce, unfiltered freq_cap=0x35
freq_cap1=0x35, freq_cap2=0x15
dev1 old_freq=0x4, freq=0x4, needs_reset=0x0
dev2 old_freq=0x4, freq=0x4, needs_reset=0x0
width_cap1=0x11, width_cap2=0x11
dev1 input ln_width1=0x4, ln_width2=0x4
dev1 input width=0x1
dev1 output ln_width1=0x4, ln_width2=0x4
dev1 input|output width=0x11
old dev1 input|output width=0x11
dev2 input|output width=0x11
old dev2 input|output width=0x11
entering ht_optimize_link
pos=0xd2, unfiltered freq_cap=0x35
pos=0xce, unfiltered freq_cap=0x1
pos=0xce, filtered freq_cap=0x1
freq_cap1=0x15, freq_cap2=0x1
dev1 old_freq=0x0, freq=0x0, needs_reset=0x0
dev2 old_freq=0x0, freq=0x0, needs_reset=0x0
width_cap1=0x0, width_cap2=0x0
dev1 input ln_width1=0x3, ln_width2=0x3
dev1 input width=0x0
dev1 output ln_width1=0x3, ln_width2=0x3
dev1 input|output width=0x0
old dev1 input|output width=0x0
dev2 input|output width=0x0
old dev2 input|output width=0x0
SMBus controller enabled
Ram1.00
setting up CPU00 northbridge registers
done.
Ram2.00
Enabling dual channel memory
Registered
166Mhz
RAM end at 0x00100000 kB
Lower RAM end at 0x00100000 kB
Ram3
Before starting clocks: Before memreset:

-- 
Hugh Greenberg



Myles Watson wrote:
>
>
> On Tue, Oct 20, 2009 at 2:53 PM, Hugh Greenberg <hng at lanl.gov 
> <mailto:hng at lanl.gov>> wrote:
>
>     Yes.  Here is the output:
>
>
>     RAM end at 0x00100000 kB
>     Lower RAM end at 0x00100000 kB
>     Ram3
>
> OK.  So it's actually hanging in RAM init, not starting the other 
> processors.
>
> Here's another patch :)
>
> Thanks,
> Myles
>