[coreboot] Asus M2V-MX SE: Interrupt issues
Paul Menzel
paulepanter at users.sourceforge.net
Mon Dec 16 01:23:47 CET 2013
Dear coreboot folks,
finally I was able to test coreboot (master with SeaBIOS) on my Asus
M2V-MX SE. Unfortunately GNU/Linux does not get to the LUKS passphrase
prompt.
[ 0.010581] ACPI: Unable to load the System Description Tables
pnp call arg1=0
[ 0.136009] PnPBIOS: dev_node_info: function not supported on this system
[ 0.140001] PnPBIOS: Unable to get node info. Aborting.
[ 0.734938] uhci_hcd 0000:00:10.0: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.0 setup!
[ 0.736070] uhci_hcd 0000:00:10.0: init 0000:00:10.0 fail, -19
[ 0.740071] ehci-pci 0000:00:10.4: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.4 setup!
[ 0.744062] ehci-pci 0000:00:10.4: init 0000:00:10.4 fail, -19
[ 0.761636] uhci_hcd 0000:00:10.1: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.1 setup!
[ 0.764067] uhci_hcd 0000:00:10.1: init 0000:00:10.1 fail, -19
[ 0.772078] uhci_hcd 0000:00:10.2: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.2 setup!
[ 0.776044] uhci_hcd 0000:00:10.2: init 0000:00:10.2 fail, -19
[ 0.793897] uhci_hcd 0000:00:10.3: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.3 setup!
[ 0.796079] uhci_hcd 0000:00:10.3: init 0000:00:10.3 fail, -19
pnp call arg1=5
[ 31.841109] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 31.848224] ata4.00: failed command: READ DMA
[ 31.852644] ata4.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 31.852644] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 31.867303] ata4.00: status: { DRDY }
Passing `acpi=off` I got a little further but there are still SATA
issues. Linux reports the following.
[ 1.316609] sata_via 0000:00:0f.0: can't find IRQ for PCI INT B; please try using pci=biosirq
[ 1.320966] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
[ 1.324122] usbcore: registered new device driver usb
[ 1.328938] sata_via 0000:00:0f.0: routed to hard irq line 0
[ 1.340738] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.344646] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.348418] ehci-pci: EHCI PCI platform driver
[ 1.357184] ------------[ cut here ]------------
[ 1.360096] WARNING: CPU: 0 PID: 75 at /build/linux-tAcKXn/linux-3.11.10/drivers/ata/libata-core.c:6234 ata_host_activate+0xeb/0xf0 [libata]()
[ 1.364064] Modules linked in: ehci_pci(+) uhci_hcd(+) ehci_hcd via_rhine(+) pata_via(+) sata_via(+) mii libata usbcore usb_common scsi_mod
[ 1.380068] CPU: 0 PID: 75 Comm: modprobe Not tainted 3.11-2-686-pae #1 Debian 3.11.10-1
[ 1.384065] Hardware name: , BIOS
[ 1.387697] 00000009 c13e5bc3 00000000 c1049d8e c14ac25c 00000000 0000004b f8478b20
[ 1.396066] 0000185a f84641fb f84641fb f75fd1cc f8471ed0 00000000 f8274560 c1049e4b
[ 1.404317] 00000009 00000000 f84641fb f75fd1cc f7496000 c122854f f7707d1f 00000080
[ 1.412315] Call Trace:
[ 1.414828] [<c13e5bc3>] ? dump_stack+0x3e/0x4e
[ 1.416072] [<c1049d8e>] ? warn_slowpath_common+0x7e/0xa0
[ 1.420074] [<f84641fb>] ? ata_host_activate+0xeb/0xf0 [libata]
[ 1.424074] [<f84641fb>] ? ata_host_activate+0xeb/0xf0 [libata]
[ 1.428074] [<f8471ed0>] ? ata_bmdma_port_intr+0xf0/0xf0 [libata]
[ 1.432071] [<c1049e4b>] ? warn_slowpath_null+0x1b/0x20
[ 1.436074] [<f84641fb>] ? ata_host_activate+0xeb/0xf0 [libata]
[ 1.440072] [<c122854f>] ? pcibios_set_master+0x2f/0xb0
[ 1.444073] [<f8272734>] ? svia_init_one+0x2a4/0x5a7 [sata_via]
[ 1.448073] [<c13ed7f6>] ? notifier_call_chain+0x46/0x60
[ 1.452074] [<c12dafc5>] ? __pm_runtime_resume+0x45/0x60
[ 1.456073] [<c122a083>] ? pci_device_probe+0x63/0xb0
[ 1.460073] [<c12d1c30>] ? __device_attach+0x30/0x30
[ 1.464072] [<c12d1a74>] ? driver_probe_device+0x54/0x1e0
[ 1.468073] [<c1229f5f>] ? pci_match_device+0xf/0xa0
[ 1.472073] [<c12d1ca1>] ? __driver_attach+0x71/0x80
[ 1.476073] [<c12d02ef>] ? bus_for_each_dev+0x3f/0x70
[ 1.480073] [<c12d1676>] ? driver_attach+0x16/0x20
[ 1.484074] [<c12d1c30>] ? __device_attach+0x30/0x30
[ 1.488074] [<c12d1357>] ? bus_add_driver+0x197/0x230
[ 1.492075] [<c1229e40>] ? store_new_id+0x110/0x110
[ 1.496075] [<c12d21c3>] ? driver_register+0x63/0x120
[ 1.500076] [<c108ecdd>] ? ktime_get+0x4d/0xe0
[ 1.504075] [<f82d9000>] ? 0xf82d8fff
[ 1.508076] [<c100205a>] ? do_one_initcall+0x5a/0x150
[ 1.512075] [<f82d9000>] ? 0xf82d8fff
[ 1.515879] [<c10428d8>] ? set_memory_nx+0x58/0x60
[ 1.516076] [<c10a0c04>] ? load_module+0x1924/0x2120
[ 1.520078] [<c10a1476>] ? SyS_init_module+0x76/0xa0
[ 1.524077] [<c13ea1d7>] ? syscall_call+0x7/0xb
[ 1.528075] ---[ end trace ab2b1229e957e6e0 ]---
[ 1.539612] scsi0 : sata_via
[ 1.540195] scsi1 : sata_via
[ 1.551726] ata1: SATA max UDMA/133 cmd 0x28a0 ctl 0x28b0 bmdma 0x2880
[ 1.552083] ata2: SATA max UDMA/133 cmd 0x28a8 ctl 0x28b4 bmdma 0x2888
[ 1.566861] scsi2 : pata_via
[ 1.572933] scsi3 : pata_via
[ 1.575953] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2890 irq 14
[ 1.576085] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2898 irq 15
[ 1.586723] via-rhine 0000:00:12.0: can't find IRQ for PCI INT A; please try using pci=biosirq
[ 1.588332] via-rhine 0000:00:12.0 eth0: VIA Rhine II at 0x12400, 00:00:de:ad:be:ef, IRQ 0
[ 1.596767] via-rhine 0000:00:12.0 eth0: MII PHY found at address 1, status 0x7949 advertising 0de1 Link 0000
[ 1.607921] uhci_hcd 0000:00:10.0: can't find IRQ for PCI INT A; please try using pci=biosirq
[ 1.608087] uhci_hcd 0000:00:10.0: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.0 setup!
[ 1.612084] uhci_hcd 0000:00:10.0: init 0000:00:10.0 fail, -19
[ 1.625665] ehci-pci 0000:00:10.4: can't find IRQ for PCI INT C; please try using pci=biosirq
[ 1.628090] ehci-pci 0000:00:10.4: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.4 setup!
[ 1.632084] ehci-pci 0000:00:10.4: init 0000:00:10.4 fail, -19
[ 1.654457] uhci_hcd 0000:00:10.1: can't find IRQ for PCI INT B; please try using pci=biosirq
[ 1.656091] uhci_hcd 0000:00:10.1: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.1 setup!
[ 1.660086] uhci_hcd 0000:00:10.1: init 0000:00:10.1 fail, -19
[ 1.681390] uhci_hcd 0000:00:10.2: can't find IRQ for PCI INT C; please try using pci=biosirq
[ 1.684094] uhci_hcd 0000:00:10.2: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.2 setup!
[ 1.688088] uhci_hcd 0000:00:10.2: init 0000:00:10.2 fail, -19
[ 1.692691] uhci_hcd 0000:00:10.3: can't find IRQ for PCI INT D; please try using pci=biosirq
[ 1.696093] uhci_hcd 0000:00:10.3: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.3 setup!
[ 1.700089] uhci_hcd 0000:00:10.3: init 0000:00:10.3 fail, -19
[ 1.760100] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 1.972108] ata2: SATA link up 1.5 Gbps (SStatus 123 SControl 300)
[ 1.984117] Switched to clocksource tsc
[ 2.140327] ata2.00: ATA-8: WDC WD20EARS-60MVWB0, 51.0AB51, max UDMA/100
[ 2.147082] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 2.160322] ata2.00: configured for UDMA/100
[ 2.164788] scsi 1:0:0:0: Direct-Access ATA WDC WD20EARS-60M 51.0 PQ: 0 ANSI: 5
[ 2.337648] sd 1:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 2.345494] sd 1:0:0:0: [sda] 4096-byte physical blocks
[ 2.351152] sd 1:0:0:0: [sda] Write Protect is off
[ 2.356082] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
pnp call arg1=5
[ 32.453347] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
[ 32.859471] ata2: lost interrupt (Status 0x50)
[ 32.863997] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 32.871098] ata2.00: failed command: READ DMA
[ 32.875513] ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 32.875513] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 32.890173] ata2.00: status: { DRDY }
[ 32.895147] ata2: soft resetting link
[ 33.131698] ata2.00: configured for UDMA/100
[ 33.136030] ata2.00: device reported invalid CHS sector 0
[ 33.141493] ata2: EH complete
[ 63.882854] ata2: lost interrupt (Status 0x50)
[ 63.887380] ata2.00: limiting speed to UDMA/66:PIO4
[ 63.892316] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 63.899421] ata2.00: failed command: READ DMA
[ 63.903836] ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 63.903836] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 63.918498] ata2.00: status: { DRDY }
[ 63.922224] ata2: soft resetting link
[ 64.127077] ata2.00: configured for UDMA/66
[ 64.131321] ata2.00: device reported invalid CHS sector 0
[ 64.136786] ata2: EH complete
[ 94.938232] ata2: lost interrupt (Status 0x50)
[ 94.942740] ata2.00: limiting speed to UDMA/33:PIO4
[ 94.947672] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 94.954771] ata2.00: failed command: READ DMA
[ 94.959185] ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 94.959185] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 94.973847] ata2.00: status: { DRDY }
[ 94.977570] ata2: soft resetting link
[ 95.198465] ata2.00: configured for UDMA/33
[ 95.202705] ata2.00: device reported invalid CHS sector 0
[ 95.208166] ata2: EH complete
Please find the log files attached.
Thanks,
Paul
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 20131215--asus-m2v-mx-se--linux-no-quiet-acpi-off--minicom.log
Type: text/x-log
Size: 128874 bytes
Desc: not available
URL: <http://www.coreboot.org/pipermail/coreboot/attachments/20131216/adf0f144/attachment-0002.log>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 20131215--asus-m2v-mx-se--minicom.log
Type: text/x-log
Size: 107923 bytes
Desc: not available
URL: <http://www.coreboot.org/pipermail/coreboot/attachments/20131216/adf0f144/attachment-0003.log>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 198 bytes
Desc: This is a digitally signed message part
URL: <http://www.coreboot.org/pipermail/coreboot/attachments/20131216/adf0f144/attachment-0001.sig>
More information about the coreboot
mailing list