[coreboot] ASUS m5a88-v AGESA port (bulldozer): Linux does not set up SATA drives
darkdefende at gmail.com
darkdefende at gmail.com
Sun Jul 7 20:49:09 CEST 2013
I did what David suggested and dumped the dsdt data. I then noticed that I had
some things wrong in the routing.asl file so I fixed that.
I also split the dsdt.asl file like the asrock/e350m1 and others have done.
When I did that I took a closer look at some of the changes I've done and
changed them to be more in line with what's in the asrock board code.
After this the "Bogus APIC", "_OSC" and the routing errors seems to be solved.
However I still get the sata error...
The "BAR can't assign mem pref" I have yet to solve. But I don't know were
I should look for a solution. I've seen some logs from other coreboot boards
where is says "BAR 15: assigned [mem 0x....". However the original bios
doesn't seem to have any of this.
Besides that I've also tried to boot with the kernel parameters:
"libata.force=nosrst" and "noapic acpi=off pci=nomsi"
When I force no soft reset it errors out with this instead:
ata1.00: qc timeout (cmd 0xec)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
Paul Menzel writes:
> Could you attach a diff of the two `kernel_log.txt` (without the time
> stamps) please?
>
Sure, "kernel_v_notime" is the original bios in the attached diff.
This diff is after I fixed the above errors.
> Two more ideas coming to my mind. First try to boot from an USB medium
> (from SeaBIOS for example) and look how far that goes and if you can
> compare lspci output from there.
Do you know any dists that comes with serial port support?
I tried fedora and ubuntu quickly but when I tried to boot them with the
grub2 payload I didn't get any output.
I don't have a spare GPU so because I can't get the onboard one working
I have to stick to the serial port...
> Maybe a newer Linux kernel also helps there.
Perhaps. But it should work because it works with vanilla bios, no?
-------------- next part --------------
--- kernel_v_notime 2013-07-07 13:11:36.000000000 +0200
+++ kernel_c_notime 2013-07-07 20:02:24.000000000 +0200
@@ -3,100 +3,97 @@
Linux version 3.2.12-gentoo (root at coreboot) (gcc version 4.5.3 (Gentoo 4.5.3-r2 p1.5, pie-0.4.7) ) #3 SMP PREEMPT Thu Jun 14 05:44:56 CEST 2012
Command line: root=/dev/sda2 console=tty0 console=ttyS0,115200,n8
BIOS-provided physical RAM map:
- BIOS-e820: 0000000000000000 - 000000000009ac00 (usable)
- BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved)
- BIOS-e820: 00000000000e2000 - 0000000000100000 (reserved)
- BIOS-e820: 0000000000100000 - 00000000cff80000 (usable)
- BIOS-e820: 00000000cff80000 - 00000000cff98000 (ACPI data)
- BIOS-e820: 00000000cff98000 - 00000000cffc0000 (ACPI NVS)
- BIOS-e820: 00000000cffc0000 - 00000000d0000000 (reserved)
- BIOS-e820: 00000000ffa00000 - 0000000100000000 (reserved)
- BIOS-e820: 0000000100000000 - 000000041f000000 (usable)
+ BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
+ BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
+ BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
+ BIOS-e820: 0000000000100000 - 00000000bffe0000 (usable)
+ BIOS-e820: 00000000bffe0000 - 00000000e0000000 (reserved)
+ BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
+ BIOS-e820: 0000000100000000 - 0000000418000000 (usable)
NX (Execute Disable) protection: active
DMI present.
No AGP bridge found
-last_pfn = 0x41f000 max_arch_pfn = 0x400000000
+last_pfn = 0x418000 max_arch_pfn = 0x400000000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
-last_pfn = 0xcff80 max_arch_pfn = 0x400000000
-found SMP MP-table at [ffff8800000ff780] ff780
+mtrr: your BIOS has configured an incorrect mask, fixing it.
+last_pfn = 0xbffe0 max_arch_pfn = 0x400000000
+found SMP MP-table at [ffff8800000f12a0] f12a0
Using GB pages for direct mapping
-init_memory_mapping: 0000000000000000-00000000cff80000
-init_memory_mapping: 0000000100000000-000000041f000000
-ACPI: RSDP 00000000000fbc30 00024 (v02 ACPIAM)
-ACPI: XSDT 00000000cff80100 00054 (v01 123011 XSDT1420 20111230 MSFT 00000097)
-ACPI: FACP 00000000cff80290 000F4 (v03 123011 FACP1420 20111230 MSFT 00000097)
-ACPI: DSDT 00000000cff80460 0F160 (v01 A1867 A1867001 00000001 INTL 20060113)
-ACPI: FACS 00000000cff98000 00040
-ACPI: APIC 00000000cff80390 0008C (v01 123011 APIC1420 20111230 MSFT 00000097)
-ACPI: MCFG 00000000cff80420 0003C (v01 123011 OEMMCFG 20111230 MSFT 00000097)
-ACPI: OEMB 00000000cff98040 00072 (v01 123011 OEMB1420 20111230 MSFT 00000097)
-ACPI: HPET 00000000cff8f8b0 00038 (v01 123011 OEMHPET 20111230 MSFT 00000097)
-ACPI: SSDT 00000000cff8f8f0 01714 (v01 A M I POWERNOW 00000001 AMD 00000001)
+init_memory_mapping: 0000000000000000-00000000bffe0000
+init_memory_mapping: 0000000100000000-0000000418000000
+ACPI: RSDP 00000000000f1280 00014 (v00 CORE )
+ACPI: RSDT 00000000bffe2424 0003C (v01 CORE COREBOOT 00000000 CORE 00000000)
+ACPI: FACP 00000000bffe53f8 000F4 (v04 CORE COREBOOT 00000000 CORE 00000000)
+ACPI: DSDT 00000000bffe24c8 02EF0 (v02 ASUS COREBOOT 00010001 INTL 20090123)
+ACPI: FACS 00000000bffe53b8 00040
+ACPI: HPET 00000000bffe54f0 00038 (v01 CORE COREBOOT 00000000 CORE 00000000)
+ACPI: APIC 00000000bffe5528 0008C (v01 CORE COREBOOT 00000000 CORE 00000000)
+ACPI: HEST 00000000bffe55b8 001D0 (v01 CORE COREBOOT 00000000 CORE 00000000)
+ACPI: SSDT 00000000bffe5790 01714 (v01 AMD POWERNOW 00000001 AMD 00000001)
+ACPI: SSDT 00000000bffe6eb0 00045 (v02 CORE COREBOOT 0000002A CORE 0000002A)
No NUMA configuration found
-Faking a node at 0000000000000000-000000041f000000
-Initmem setup node 0 0000000000000000-000000041f000000
- NODE_DATA [000000041effb000 - 000000041effffff]
+Faking a node at 0000000000000000-0000000418000000
+Initmem setup node 0 0000000000000000-0000000418000000
+ NODE_DATA [0000000417ffb000 - 0000000417ffffff]
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
- Normal 0x00100000 -> 0x0041f000
+ Normal 0x00100000 -> 0x00418000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
- 0: 0x00000010 -> 0x0000009a
- 0: 0x00000100 -> 0x000cff80
- 0: 0x00100000 -> 0x0041f000
+ 0: 0x00000010 -> 0x0000009f
+ 0: 0x00000100 -> 0x000bffe0
+ 0: 0x00100000 -> 0x00418000
ACPI: PM-Timer IO Port: 0x808
-ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] enabled)
-ACPI: LAPIC (acpi_id[0x02] lapic_id[0x11] enabled)
-ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] enabled)
-ACPI: LAPIC (acpi_id[0x04] lapic_id[0x13] enabled)
-ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] enabled)
-ACPI: LAPIC (acpi_id[0x06] lapic_id[0x15] enabled)
-ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] enabled)
-ACPI: LAPIC (acpi_id[0x08] lapic_id[0x17] enabled)
-ACPI: IOAPIC (id[0x18] address[0xfec00000] gsi_base[0])
-IOAPIC[0]: apic_id 24, version 33, address 0xfec00000, GSI 0-23
+ACPI: LAPIC (acpi_id[0x00] lapic_id[0x10] enabled)
+ACPI: LAPIC (acpi_id[0x01] lapic_id[0x11] enabled)
+ACPI: LAPIC (acpi_id[0x02] lapic_id[0x12] enabled)
+ACPI: LAPIC (acpi_id[0x03] lapic_id[0x13] enabled)
+ACPI: LAPIC (acpi_id[0x04] lapic_id[0x14] enabled)
+ACPI: LAPIC (acpi_id[0x05] lapic_id[0x15] enabled)
+ACPI: LAPIC (acpi_id[0x06] lapic_id[0x16] enabled)
+ACPI: LAPIC (acpi_id[0x07] lapic_id[0x17] enabled)
+ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
+IOAPIC[0]: apic_id 8, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
Using ACPI (MADT) for SMP configuration information
-ACPI: HPET id: 0x8300 base: 0xfed00000
+ACPI: HPET id: 0x43538210 base: 0xfed00000
SMP: Allowing 8 CPUs, 0 hotplug CPUs
-PM: Registered nosave memory: 000000000009a000 - 000000000009b000
-PM: Registered nosave memory: 000000000009b000 - 00000000000a0000
-PM: Registered nosave memory: 00000000000a0000 - 00000000000e2000
-PM: Registered nosave memory: 00000000000e2000 - 0000000000100000
-PM: Registered nosave memory: 00000000cff80000 - 00000000cff98000
-PM: Registered nosave memory: 00000000cff98000 - 00000000cffc0000
-PM: Registered nosave memory: 00000000cffc0000 - 00000000d0000000
-PM: Registered nosave memory: 00000000d0000000 - 00000000ffa00000
-PM: Registered nosave memory: 00000000ffa00000 - 0000000100000000
-Allocating PCI resources starting at d0000000 (gap: d0000000:2fa00000)
+PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
+PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
+PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
+PM: Registered nosave memory: 00000000bffe0000 - 00000000e0000000
+PM: Registered nosave memory: 00000000e0000000 - 00000000f8000000
+PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
+PM: Registered nosave memory: 00000000fc000000 - 0000000100000000
+Allocating PCI resources starting at e0000000 (gap: e0000000:18000000)
setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
-PERCPU: Embedded 26 pages/cpu @ffff88041ec00000 s76416 r8192 d21888 u262144
-Built 1 zonelists in Zone order, mobility grouping on. Total pages: 4056901
+PERCPU: Embedded 26 pages/cpu @ffff880417c00000 s76416 r8192 d21888 u262144
+Built 1 zonelists in Zone order, mobility grouping on. Total pages: 3963242
Policy zone: Normal
Kernel command line: root=/dev/sda2 console=tty0 console=ttyS0,115200,n8
PID hash table entries: 4096 (order: 3, 32768 bytes)
xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
Checking aperture...
No AGP bridge found
-Node 0: aperture @ 0 size 32 MB
+Node 0: aperture @ b292000000 size 32 MB
+Aperture beyond 4GB. Ignoring.
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
-Mapping aperture over 65536 KB of RAM @ c4000000
-PM: Registered nosave memory: 00000000c4000000 - 00000000c8000000
-Memory: 16092424k/17285120k available (7836k kernel code, 787416k absent, 405280k reserved, 5094k data, 652k init)
+Mapping aperture over 65536 KB of RAM @ b4000000
+PM: Registered nosave memory: 00000000b4000000 - 00000000b8000000
+Memory: 15722144k/17170432k available (7836k kernel code, 1049156k absent, 399132k reserved, 5094k data, 652k init)
SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:4352 nr_irqs:744 16
-Extended CMOS year: 2000
-Console: colour VGA+ 80x25
+Console: colour dummy device 80x25
console [tty0] enabled
console [ttyS0] enabled
Fast TSC calibration using PIT
-Detected 3114.509 MHz processor.
-Calibrating delay loop (skipped), value calculated using timer frequency.. 6229.01 BogoMIPS (lpj=3114509)
+Detected 3100.410 MHz processor.
+Calibrating delay loop (skipped), value calculated using timer frequency.. 6200.82 BogoMIPS (lpj=3100410)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux: Initializing.
@@ -109,7 +106,7 @@
CPU: Processor Core ID: 0
mce: CPU supports 7 MCE banks
ACPI: Core revision 20110623
-..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
+..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: AMD FX(tm)-8120 Eight-Core Processor stepping 02
Performance Events: AMD Family 15h PMU driver.
... version: 0
@@ -128,15 +125,12 @@
#6
#7 Ok.
Brought up 8 CPUs
-Total of 8 processors activated (49820.29 BogoMIPS).
-PM: Registering ACPI NVS region at cff98000 (163840 bytes)
-RTC time: 20:31:44, date: 12/03/12
+Total of 8 processors activated (49597.71 BogoMIPS).
+RTC time: 21:07:13, date: 01/02/13
NET: Registered protocol family 16
kworker/u:0 used greatest stack depth: 5424 bytes left
Extended Config Space enabled on 1 nodes
ACPI: bus type pci registered
-PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
-PCI: not using MMCONFIG
PCI: Using configuration type 1 for base access
PCI: Using configuration type 1 for extended access
bio: create slab <bio-0> at 0
@@ -144,22 +138,20 @@
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
-ACPI: Executed 3 blocks of module-level executable AML code
+ACPI: Executed 2 blocks of module-level executable AML code
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
+ACPI: BIOS offers _BFS
+ACPI: If "acpi.bfs=1" improves resume, please notify linux-acpi at vger.kernel.org
ACPI: Using IOAPIC for interrupt routing
-PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
-PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
-ACPI: EC: GPE = 0xa, I/O: command/status = 0x66, data = 0x62
+ACPI: Power Resource [PFN0] (on)
ACPI: No dock devices found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
-pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
-pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
-pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
-pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff]
-pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xdfffffff]
-pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff]
+pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
+pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
+pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
+pci_root PNP0A08:00: host bridge window [mem 0xe0000000-0xffffffff]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:09.0: PCI bridge to [bus 02-02]
pci 0000:00:0a.0: PCI bridge to [bus 03-03]
@@ -168,14 +160,14 @@
pci 0000:00:15.1: PCI bridge to [bus 06-06]
pci0000:00: Requesting ACPI _OSC control (0x1d)
pci0000:00: ACPI _OSC control (0x1d) granted
-ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 14 15)
-ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 14 15)
-ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 14 15)
-ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *9 10 11 14 15)
-ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 14 15) *0
-ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 14 15) *0
-ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 14 15) *0
-ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 14 15) *0
+ACPI: PCI Interrupt Link [INTA] (IRQs 3 4 5 7 10 11 12 15) *0
+ACPI: PCI Interrupt Link [INTB] (IRQs 3 4 5 7 10 11 12 15) *0
+ACPI: PCI Interrupt Link [INTC] (IRQs 3 4 5 7 10 11 12 15) *0
+ACPI: PCI Interrupt Link [INTD] (IRQs 3 4 5 7 10 11 12 15) *0
+ACPI: PCI Interrupt Link [INTE] (IRQs 3 4 5 7 10 11 12 15) *0
+ACPI: PCI Interrupt Link [INTF] (IRQs 9) *0
+ACPI: PCI Interrupt Link [INTG] (IRQs 3 4 5 7 10 11 12 15) *0
+ACPI: PCI Interrupt Link [INTH] (IRQs 3 4 5 7 10 11 12 15) *0
vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:01:05.0
@@ -185,6 +177,8 @@
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.24.
PCI: Using ACPI for IRQ routing
+pci 0000:00:01.0: no compatible bridge window for [mem 0xc0000000-0xdfffffff 64bit pref]
+pci 0000:01:05.0: no compatible bridge window for [mem 0xc0000000-0xdfffffff pref]
cfg80211: Calling CRDA to update world regulatory domain
NetLabel: Initializing
NetLabel: domain hash size = 128
@@ -195,60 +189,25 @@
Switching to clocksource hpet
pnp: PnP ACPI init
ACPI: bus type pnp registered
-system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved
-system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved
-system 00:0a: [io 0x04d0-0x04d1] has been reserved
-system 00:0a: [io 0x040b] has been reserved
-system 00:0a: [io 0x04d6] has been reserved
-system 00:0a: [io 0x0c00-0x0c01] has been reserved
-system 00:0a: [io 0x0c14] has been reserved
-system 00:0a: [io 0x0c50-0x0c51] has been reserved
-system 00:0a: [io 0x0c52] has been reserved
-system 00:0a: [io 0x0c6c] has been reserved
-system 00:0a: [io 0x0c6f] has been reserved
-system 00:0a: [io 0x0cd0-0x0cd1] has been reserved
-system 00:0a: [io 0x0cd2-0x0cd3] has been reserved
-system 00:0a: [io 0x0cd4-0x0cd5] has been reserved
-system 00:0a: [io 0x0cd6-0x0cd7] has been reserved
-system 00:0a: [io 0x0cd8-0x0cdf] has been reserved
-system 00:0a: [io 0x0b00-0x0b3f] has been reserved
-system 00:0a: [io 0x0800-0x089f] has been reserved
-system 00:0a: [io 0x0b00-0x0b1f] has been reserved
-system 00:0a: [io 0x0b20-0x0b3f] has been reserved
-system 00:0a: [io 0x0900-0x090f] has been reserved
-system 00:0a: [io 0x0910-0x091f] has been reserved
-system 00:0a: [io 0xfe00-0xfefe] has been reserved
-system 00:0a: [mem 0xffb80000-0xffbfffff] has been reserved
-system 00:0a: [mem 0xfec10000-0xfec1001f] has been reserved
-system 00:0a: [mem 0xfed80000-0xfed80fff] has been reserved
-system 00:0b: [io 0x0230-0x023f] has been reserved
-system 00:0b: [io 0x0290-0x029f] has been reserved
-system 00:0b: [io 0x0300-0x030f] has been reserved
-system 00:0b: [io 0x0a30-0x0a3f] has been reserved
-system 00:0c: [mem 0xe0000000-0xefffffff] has been reserved
-system 00:0d: [mem 0x00000000-0x0009ffff] could not be reserved
-system 00:0d: [mem 0x000c0000-0x000cffff] could not be reserved
-system 00:0d: [mem 0x000e0000-0x000fffff] could not be reserved
-system 00:0d: [mem 0x00100000-0xcfffffff] could not be reserved
-system 00:0d: [mem 0xfec00000-0xffffffff] could not be reserved
-pnp: PnP ACPI: found 14 devices
+pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
+pci 0000:00:01.0: BAR 15: can't assign mem pref (size 0x20000000)
+pci 0000:01:05.0: BAR 0: can't assign mem pref (size 0x20000000)
+pci 0000:01:05.0: BAR 0: trying firmware assignment [mem 0xc0000000-0xdfffffff pref]
+pci 0000:01:05.0: BAR 0: [mem 0xc0000000-0xdfffffff pref] conflicts with reserved [mem 0xbffe0000-0xdfffffff]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
-pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
-pci 0000:00:01.0: bridge window [mem 0xfe800000-0xfe9fffff]
-pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
+pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
+pci 0000:00:01.0: bridge window [mem 0xe0100000-0xe02fffff]
pci 0000:00:09.0: PCI bridge to [bus 02-02]
-pci 0000:00:09.0: bridge window [io 0xd000-0xdfff]
-pci 0000:00:09.0: bridge window [mem 0xfea00000-0xfeafffff]
+pci 0000:00:09.0: bridge window [io 0x2000-0x2fff]
+pci 0000:00:09.0: bridge window [mem 0xe0300000-0xe03fffff]
pci 0000:00:0a.0: PCI bridge to [bus 03-03]
-pci 0000:00:0a.0: bridge window [mem 0xfeb00000-0xfebfffff]
+pci 0000:00:0a.0: bridge window [mem 0xe0400000-0xe04fffff]
pci 0000:00:14.4: PCI bridge to [bus 04-04]
pci 0000:00:15.0: PCI bridge to [bus 05-05]
pci 0000:00:15.1: PCI bridge to [bus 06-06]
-pci 0000:00:15.1: bridge window [io 0xe000-0xefff]
-pci 0000:00:15.1: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
-pci 0000:00:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
-pci 0000:00:0a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
+pci 0000:00:15.1: bridge window [io 0x3000-0x3fff]
+pci 0000:00:15.1: bridge window [mem 0xe0000000-0xe00fffff 64bit pref]
pci 0000:00:15.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:15.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
NET: Registered protocol family 2
@@ -282,26 +241,26 @@
pci 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:03:00.0: PCI INT A disabled
PCI-DMA: Disabling AGP.
-PCI-DMA: aperture base @ c4000000 size 65536 KB
+PCI-DMA: aperture base @ b4000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
perf: AMD IBS detected (0x000000ff)
-microcode: CPU0: patch_level=0x06000613
-microcode: CPU1: patch_level=0x06000613
-microcode: CPU2: patch_level=0x06000613
-microcode: CPU3: patch_level=0x06000613
-microcode: CPU4: patch_level=0x06000613
-microcode: CPU5: patch_level=0x06000613
-microcode: CPU6: patch_level=0x06000613
-microcode: CPU7: patch_level=0x06000613
+microcode: CPU0: patch_level=0x06000624
+microcode: CPU1: patch_level=0x06000624
+microcode: CPU2: patch_level=0x06000624
+microcode: CPU3: patch_level=0x06000624
+microcode: CPU4: patch_level=0x06000624
+microcode: CPU5: patch_level=0x06000624
+microcode: CPU6: patch_level=0x06000624
+microcode: CPU7: patch_level=0x06000624
microcode: Microcode Update Driver: v2.00 <tigran at aivazian.fsnet.co.uk>, Peter Oruba
audit: initializing netlink socket (disabled)
-type=2000 audit(1354566703.447:1): initialized
+type=2000 audit(1357160832.396:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
NTFS driver 2.1.30 [Flags: R/W].
-msgmni has been set to 31559
+msgmni has been set to 30836
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
@@ -309,90 +268,53 @@
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
-00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
+serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
+ACPI: Fan [FAN0] (on)
+thermal LNXTHERM:00: registered as thermal_zone0
+ACPI: Thermal Zone [TZ00] (40 C)
[drm] Initialized drm 1.1.0 20060810
[drm] radeon defaulting to kernel modesetting.
[drm] radeon kernel modesetting enabled.
radeon 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
-[drm] initializing kernel modesetting (RS880 0x1002:0x9715 0x1043:0x843E).
-[drm] register mmio base: 0xFE9F0000
+[drm] initializing kernel modesetting (RS880 0x1002:0x9715 0x1002:0x0000).
+[drm] register mmio base: 0xE0200000
[drm] register mmio size: 65536
-ATOM BIOS: 113
-radeon 0000:01:05.0: VRAM: 368M 0x00000000C0000000 - 0x00000000D6FFFFFF (368M used)
-radeon 0000:01:05.0: GTT: 512M 0x00000000A0000000 - 0x00000000BFFFFFFF
-[drm] Detected VRAM RAM=368M, BAR=256M
-[drm] RAM width 32bits DDR
-[TTM] Zone kernel: Available graphics memory: 8079188 kiB.
-[TTM] Zone dma32: Available graphics memory: 2097152 kiB.
-[TTM] Initializing pool allocator.
-[drm] radeon: 368M of VRAM memory ready
-[drm] radeon: 512M of GTT memory ready.
-[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
-[drm] Driver supports precise vblank timestamp query.
-[drm] radeon: irq initialized.
-[drm] GART: num cpu pages 131072, num gpu pages 131072
-[drm] Loading RS780 Microcode
-[drm] PCIE GART of 512M enabled (table at 0x00000000C0040000).
-radeon 0000:01:05.0: WB enabled
-[drm] ring test succeeded in 1 usecs
-[drm] radeon: ib pool ready.
-[drm] ib test succeeded in 0 usecs
-[drm] Radeon Display Connectors
-[drm] Connector 0:
-[drm] VGA
-[drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
-[drm] Encoders:
-[drm] CRT1: INTERNAL_KLDSCP_DAC1
-[drm] Connector 1:
-[drm] DVI-D
-[drm] HPD1
-[drm] DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c
-[drm] Encoders:
-[drm] DFP3: INTERNAL_KLDSCP_LVTMA
-[drm] radeon: power management initialized
-[drm] fb mappable at 0xD0142000
-[drm] vram apper at 0xD0000000
-[drm] size 9216000
-[drm] fb depth is 24
-[drm] pitch is 7680
-fbcon: radeondrmfb (fb0) is primary device
-Console: switching to colour frame buffer device 240x75
-Refined TSC clocksource calibration: 3113.984 MHz.
-Switching to clocksource tsc
-fb0: radeondrmfb frame buffer device
-drm: registered panic notifier
-[drm] Initialized radeon 2.12.0 20080528 for 0000:01:05.0 on minor 0
+radeon 0000:01:05.0: Invalid ROM contents
+[drm:radeon_get_bios] *ERROR* Unable to locate a BIOS ROM
+radeon 0000:01:05.0: Fatal error during GPU init
+[drm] radeon: finishing device.
+[TTM] Memory type 2 has not been initialized.
+radeon 0000:01:05.0: PCI INT A disabled
+radeon: probe of 0000:01:05.0 failed with error -22
brd: module loaded
loop: module loaded
ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
-ahci 0000:00:11.0: AHCI 0001.0200 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
-ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
+ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode
+ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp fbs pio slum part ccc
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
-scsi4 : ahci
-scsi5 : ahci
-ata1: SATA max UDMA/133 abar m1024 at 0xfe7ffc00 port 0xfe7ffd00 irq 19
-ata2: SATA max UDMA/133 abar m1024 at 0xfe7ffc00 port 0xfe7ffd80 irq 19
-ata3: SATA max UDMA/133 abar m1024 at 0xfe7ffc00 port 0xfe7ffe00 irq 19
-ata4: SATA max UDMA/133 abar m1024 at 0xfe7ffc00 port 0xfe7ffe80 irq 19
-ata5: SATA max UDMA/133 abar m1024 at 0xfe7ffc00 port 0xfe7fff00 irq 19
-ata6: SATA max UDMA/133 abar m1024 at 0xfe7ffc00 port 0xfe7fff80 irq 19
+ata1: SATA max UDMA/133 abar m1024 at 0xe0508000 port 0xe0508100 irq 44
+ata2: SATA max UDMA/133 abar m1024 at 0xe0508000 port 0xe0508180 irq 44
+ata3: SATA max UDMA/133 abar m1024 at 0xe0508000 port 0xe0508200 irq 44
+ata4: SATA max UDMA/133 abar m1024 at 0xe0508000 port 0xe0508280 irq 44
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
+Refined TSC clocksource calibration: 3100.115 MHz.
+Switching to clocksource tsc
e100: Copyright(c) 1999-2006 Intel Corporation
e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
e1000: Copyright (c) 1999-2006 Intel Corporation.
sky2: driver version 1.30
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:06:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
-r8169 0000:06:00.0: eth0: RTL8168evl/8111evl at 0xffffc9000187e000, c8:60:00:60:b1:c2, XID 0c900800 IRQ 44
+r8169 0000:06:00.0: eth0: RTL8168evl/8111evl at 0xffffc900025d0000, 00:00:00:00:00:03, XID 0c900800 IRQ 45
r8169 0000:06:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
@@ -400,7 +322,7 @@
ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
ehci_hcd 0000:00:12.2: debug port 1
-ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe7ff800
+ehci_hcd 0000:00:12.2: irq 17, io mem 0xe0508400
ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
@@ -414,7 +336,7 @@
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
ehci_hcd 0000:00:13.2: debug port 1
-ehci_hcd 0000:00:13.2: irq 17, io mem 0xfe7ff400
+ehci_hcd 0000:00:13.2: irq 17, io mem 0xe0508500
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
@@ -425,39 +347,25 @@
hub 2-0:1.0: 5 ports detected
ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:16.2: EHCI Host Controller
-ata5: SATA link down (SStatus 0 SControl 300)
-ata3: SATA link down (SStatus 0 SControl 300)
-ata4: SATA link down (SStatus 0 SControl 300)
-ata6: SATA link down (SStatus 0 SControl 300)
ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
ehci_hcd 0000:00:16.2: debug port 1
-ehci_hcd 0000:00:16.2: irq 17, io mem 0xfe7ff000
+ehci_hcd 0000:00:16.2: irq 17, io mem 0xe0508600
ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: EHCI Host Controller
+ata4: SATA link down (SStatus 0 SControl 300)
+ata3: SATA link down (SStatus 0 SControl 300)
usb usb3: Manufacturer: Linux 3.2.12-gentoo ehci_hcd
usb usb3: SerialNumber: 0000:00:16.2
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
-ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
-ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
-ata1.00: ATA-8: Corsair Force GT, 1.3.3, max UDMA/133
-ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
-ata1.00: configured for UDMA/133
-scsi 0:0:0:0: Direct-Access ATA Corsair Force GT 1.3. PQ: 0 ANSI: 5
-sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
-sd 0:0:0:0: Attached scsi generic sg0 type 0
-sd 0:0:0:0: [sda] Write Protect is off
-sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- sda: sda1 sda2
ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
-sd 0:0:0:0: [sda] Attached SCSI disk
ohci_hcd 0000:00:12.0: OHCI Host Controller
ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
-ohci_hcd 0000:00:12.0: irq 18, io mem 0xfe7fe000
+ohci_hcd 0000:00:12.0: irq 18, io mem 0xe0504000
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
@@ -468,7 +376,7 @@
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
-ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe7fd000
+ohci_hcd 0000:00:13.0: irq 18, io mem 0xe0505000
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: OHCI Host Controller
@@ -476,21 +384,10 @@
usb usb5: SerialNumber: 0000:00:13.0
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 5 ports detected
-ata2.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
-ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
-ata2.00: configured for UDMA/133
-scsi 1:0:0:0: Direct-Access ATA WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
-sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
-sd 1:0:0:0: [sdb] 4096-byte physical blocks
-sd 1:0:0:0: Attached scsi generic sg1 type 0
-sd 1:0:0:0: [sdb] Write Protect is off
-sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 >
ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
-sd 1:0:0:0: [sdb] Attached SCSI disk
ohci_hcd 0000:00:14.5: OHCI Host Controller
ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 6
-ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe7fc000
+ohci_hcd 0000:00:14.5: irq 18, io mem 0xe0506000
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: OHCI Host Controller
@@ -501,7 +398,7 @@
ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:16.0: OHCI Host Controller
ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 7
-ohci_hcd 0000:00:16.0: irq 18, io mem 0xfe7f3000
+ohci_hcd 0000:00:16.0: irq 18, io mem 0xe0507000
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: OHCI Host Controller
@@ -515,14 +412,12 @@
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
-i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
-i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
+i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
mousedev: PS/2 mouse device common for all mice
-rtc_cmos 00:03: RTC can wake from S4
-rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
-rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
-input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
+rtc_cmos 00:01: RTC can wake from S4
+rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
+rtc0: alarms up to one day, 114 bytes nvram, hpet irqs
device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel at redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
@@ -530,10 +425,21 @@
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
snd_hda_intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
+hda-intel: spurious response 0x0:0x0, last cmd=0x0f0000
+hda-intel: azx_get_response timeout, switching to polling mode: last cmd=0x100f0000
+hda-intel: Codec #1 probe error; disabling it...
+hda-intel: spurious response 0x0:0x0, last cmd=0x0f0000
+hda-intel: Codec #2 probe error; disabling it...
+hda-intel: no codecs initialized
+snd_hda_intel 0000:00:14.2: PCI INT A disabled
snd_hda_intel 0000:01:05.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
+hda-intel: azx_get_response timeout, switching to polling mode: last cmd=0x000f0000
+ata1: softreset failed (1st FIS failed)
+ata2: softreset failed (1st FIS failed)
+hda-intel: Codec #0 probe error; disabling it...
+hda_intel: azx_get_response timeout, switching to single_cmd mode: last cmd=0x00070503
ALSA device list:
- #0: HDA ATI SB at 0xfe7f4000 irq 16
- #1: HDA ATI HDMI at 0xfe9e8000 irq 19
+ #0: HDA ATI HDMI at 0xe0210000 irq 19
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ctnetlink v0.93: registering with nfnetlink.
@@ -546,20 +452,42 @@
NET: Registered protocol family 17
Registering the dns_resolver key type
registered taskstats version 1
- Magic number: 8:860:547
+ Magic number: 13:410:145
+ata_port ata2: hash matches
+ ata2: hash matches
+acpi device:16: hash matches
console [netcon0] enabled
netconsole: network logging started
+ata1: softreset failed (1st FIS failed)
+ata2: softreset failed (1st FIS failed)
+ata1: softreset failed (1st FIS failed)
+ata1: limiting SATA link speed to 3.0 Gbps
+ata2: softreset failed (1st FIS failed)
+ata2: limiting SATA link speed to 3.0 Gbps
+ata1: softreset failed (1st FIS failed)
+ata1: reset failed, giving up
+ata2: softreset failed (1st FIS failed)
+ata2: reset failed, giving up
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
-EXT3-fs (sda2): error: couldn't mount because of unsupported optional features (240)
-EXT2-fs (sda2): error: couldn't mount because of unsupported optional features (240)
-EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
-VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
-Freeing unused kernel memory: 652k freed
-Write protecting the kernel read-only data: 12288k
-Freeing unused kernel memory: 332k freed
-Freeing unused kernel memory: 1392k freed
+Root-NFS: no NFS server address
+VFS: Unable to mount root fs via NFS, trying floppy.
+VFS: Cannot open root device "sda2" or unknown-block(2,0)
+Please append a correct "root=" boot option; here are the available partitions:
+Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
+Pid: 1, comm: swapper/0 Tainted: G I 3.2.12-gentoo #3
+Call Trace:
+ [<ffffffff8179857d>] panic+0x96/0x1a4
+ [<ffffffff817986c7>] ? printk+0x3c/0x3e
+ [<ffffffff81cb5f3b>] mount_block_root+0x14a/0x1ea
+ [<ffffffff81cb61ca>] mount_root+0xe0/0xeb
+ [<ffffffff811307e1>] ? sys_unlink+0x11/0x20
+ [<ffffffff81cb6345>] prepare_namespace+0x170/0x19d
+ [<ffffffff81cb5c91>] kernel_init+0x140/0x150
+ [<ffffffff817a4134>] kernel_thread_helper+0x4/0x10
+ [<ffffffff81cb5b51>] ? start_kernel+0x342/0x342
+ [<ffffffff817a4130>] ? gs_change+0xb/0xb
More information about the coreboot
mailing list