[flashrom] [commit] r693 - trunk

[svn at flashrom.org]

Author: hailfinger
Date: 2009-08-19 17:03:28 +0200 (Wed, 19 Aug 2009)
New Revision: 693

Modified:
   trunk/flashrom.8
   trunk/flashrom.c
Log:
Current programmer parameter syntax is
-p programmer=parameter
Unfortunately, many parameters are of the form variable=val, so we get
commandlines like this:
flashrom -p it87spi=port=0x820
and this looks horrible.

Using : instead of = would make such parameters look better:
flashrom -p it87spi:port=0x820

As a side benefit, this patch mentions the programmer name in the error
message if it is unknown.

Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006 at gmx.net>
Acked-by: Stefan Reinauer <stepan at coresystems.de>


Modified: trunk/flashrom.8
===================================================================
--- trunk/flashrom.8	2009-08-19 13:55:34 UTC (rev 692)
+++ trunk/flashrom.8	2009-08-19 15:03:28 UTC (rev 693)
@@ -150,7 +150,7 @@
 .sp
 The dummy programmer has an optional parameter specifying the bus types it
 should support. For that you have to use the
-.B "flashrom -p dummy=type"
+.B "flashrom -p dummy:type"
 syntax where
 .B type
 can be any comma-separated combination of
@@ -158,11 +158,11 @@
 in any order.
 .sp
 Example:
-.B "flashrom -p dummy=lpc,fwh"
+.B "flashrom -p dummy:lpc,fwh"
 .sp
 If you have multiple supported PCI cards which can program flash chips
 (NICs, SATA/IDE controllers, etc.) in your system, you must use the
-.B "flashrom -p xxxx=bb:dd.f"
+.B "flashrom -p xxxx:bb:dd.f"
 syntax to explicitly select one of them, where
 .B xxxx
 is the name of the programmer
@@ -174,7 +174,7 @@
 is the PCI function number of the desired NIC.
 .sp
 Example:
-.B "flashrom -p nic3com=05:04.0"
+.B "flashrom -p nic3com:05:04.0"
 .sp
 Currently the following programmers support this mechanism:
 .BR nic3com ,
@@ -183,14 +183,14 @@
 The it87spi programmer has an optional parameter which will set the I/O base
 port of the IT87* SPI controller interface to the port specified in the
 parameter. For that you have to use the
-.B "flashrom -p it87spi=port=portnum"
+.B "flashrom -p it87spi:port=portnum"
 syntax where
 .B portnum
 is an I/O port number which must be a multiple of 8.
 .sp
 The ft2232spi programmer has an optional parameter specifying the controller
 type and interface/port it should support. For that you have to use the
-.B "flashrom -p ft2232spi=model,port=interface"
+.B "flashrom -p ft2232spi:model,port=interface"
 syntax where
 .B model
 can be any of
@@ -208,9 +208,9 @@
 The serprog programmer has an optional parameter specifying either a serial
 device/baud combination or an IP/port combination for communication with the
 programmer. For serial, you have to use the
-.B "flashrom -p serprog=/dev/device:baud"
+.B "flashrom -p serprog:/dev/device:baud"
 syntax and for IP, you have to use
-.B "flashrom -p serprog=ip:port"
+.B "flashrom -p serprog:ip:port"
 instead. More information about serprog is available in serprog-protocol.txt in
 the source distribution.
 .sp

Modified: trunk/flashrom.c
===================================================================
--- trunk/flashrom.c	2009-08-19 13:55:34 UTC (rev 692)
+++ trunk/flashrom.c	2009-08-19 15:03:28 UTC (rev 693)
@@ -708,7 +708,7 @@
 				namelen = strlen(name);
 				if (strncmp(optarg, name, namelen) == 0) {
 					switch (optarg[namelen]) {
-					case '=':
+					case ':':
 						programmer_param = strdup(optarg + namelen + 1);
 						break;
 					case '\0':
@@ -725,7 +725,7 @@
 				}
 			}
 			if (programmer == PROGRAMMER_INVALID) {
-				printf("Error: Unknown programmer.\n");
+				printf("Error: Unknown programmer %s.\n", optarg);
 				exit(1);
 			}
 			break;