[flashrom] [PATCH] Use extract_param everywhere
Carl-Daniel Hailfinger
c-d.hailfinger.devel.2006 at gmx.net
Sat Jul 3 03:25:14 CEST 2010
Various places in the flashrom source feature custom parameter
extraction from programmer_param. This led to wildly differing syntax
for programmer parameters, and it also voids pretty much every
assumption you could make about programmer_param. The latter is a
problem for libflashrom.
Use extract_param everywhere, clean up related code and make it more
foolproof.
Add two instances of exit(1) where we have no option to return an error.
Remove six instances of exit(1) where returning an error was possible.
Once this patch is in, it is very easy to make programmer_param static.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006 at gmx.net>
Index: flashrom-extract_param_everywhere/flashrom.8
===================================================================
--- flashrom-extract_param_everywhere/flashrom.8 (Revision 1067)
+++ flashrom-extract_param_everywhere/flashrom.8 (Arbeitskopie)
@@ -183,7 +183,7 @@
.BR "* ft2232_spi" " (for SPI flash ROMs attached to a FT2232H/FT4232H based\
USB SPI programmer)"
.sp
-.BR "* serprog" " (for flash ROMs attached to Urja's AVR programmer)"
+.BR "* serprog" " (for flash ROMs attached to a programmer speaking serprog)"
.sp
.BR "* buspirate_spi" " (for SPI flash ROMs attached to a Bus Pirate)"
.sp
@@ -296,22 +296,23 @@
.BR "dummy " programmer
An optional parameter specifies the bus types it
should support. For that you have to use the
-.B "flashrom \-p dummy:type"
+.B "flashrom \-p dummy:bus=[type[+type[+type]]]"
syntax where
.B type
-can be any comma-separated combination of
-.BR parallel ", " lpc ", " fwh ", " spi ", or " all
-(in any order).
+can be any of
+.BR parallel ", " lpc ", " fwh ", " spi
+in any order. If you specify bus without type, all buses will be disabled.
+If you do not specify bus, all buses will be enabled.
.sp
Example:
-.B "flashrom \-p dummy:lpc,fwh"
+.B "flashrom \-p dummy:bus=lpc+fwh"
.TP
.BR "nic3com" , " nicrealtek" , " nicsmc1211" , " gfxnvidia" , " satasii \
" and " atahpt " programmers
These programmers have an option to specify the PCI address of the card
your want to use, which must be specified if more than one card supported
by the selected programmer is installed in your system. The syntax is
-.BR "flashrom \-p xxxx:bb:dd.f" ,
+.BR "flashrom \-p xxxx:pci=bb:dd.f" ,
where
.B xxxx
is the name of the programmer
@@ -323,7 +324,7 @@
is the PCI function number of the desired device.
.sp
Example:
-.B "flashrom \-p nic3com:05:04.0"
+.B "flashrom \-p nic3com:pci=05:04.0"
.TP
.BR "it87spi " programmer
An optional
@@ -342,7 +343,7 @@
An optional parameter specifies the controller
type and interface/port it should support. For that you have to use the
.sp
-.B " flashrom \-p ft2232_spi:model,port=interface"
+.B " flashrom \-p ft2232_spi:type=model,port=interface"
.sp
syntax where
.B model
@@ -363,11 +364,11 @@
programmer. In the device/baud combination, the device has to start with a
slash. For serial, you have to use the
.sp
-.B " flashrom \-p serprog:/dev/device:baud"
+.B " flashrom \-p serprog:dev=/dev/device:baud"
.sp
syntax and for IP, you have to use
.sp
-.B " flashrom \-p serprog:ip:port"
+.B " flashrom \-p serprog:ip=ipaddr:port"
.sp
instead. More information about serprog is available in
.B serprog-protocol.txt
Index: flashrom-extract_param_everywhere/drkaiser.c
===================================================================
--- flashrom-extract_param_everywhere/drkaiser.c (Revision 1067)
+++ flashrom-extract_param_everywhere/drkaiser.c (Arbeitskopie)
@@ -36,10 +36,14 @@
int drkaiser_init(void)
{
uint32_t addr;
+ char *devstring;
get_io_perms();
+
+ devstring = extract_param(&programmer_param, "pci", ",");
pcidev_init(PCI_VENDOR_ID_DRKAISER, PCI_BASE_ADDRESS_2,
- drkaiser_pcidev, programmer_param);
+ drkaiser_pcidev, devstring);
+ free(devstring);
/* Write magic register to enable flash write. */
pci_write_word(pcidev_dev, PCI_MAGIC_DRKAISER_ADDR,
@@ -53,6 +57,7 @@
addr, 128 * 1024);
buses_supported = CHIP_BUSTYPE_PARALLEL;
+
return 0;
}
@@ -60,7 +65,6 @@
{
/* Write protect the flash again. */
pci_write_word(pcidev_dev, PCI_MAGIC_DRKAISER_ADDR, 0);
- free(programmer_param);
pci_cleanup(pacc);
release_io_perms();
return 0;
Index: flashrom-extract_param_everywhere/it87spi.c
===================================================================
--- flashrom-extract_param_everywhere/it87spi.c (Revision 1067)
+++ flashrom-extract_param_everywhere/it87spi.c (Arbeitskopie)
@@ -142,22 +142,24 @@
flashport = sio_read(port, 0x64) << 8;
flashport |= sio_read(port, 0x65);
msg_pdbg("Serial flash port 0x%04x\n", flashport);
- if (programmer_param && !strlen(programmer_param)) {
- free(programmer_param);
- programmer_param = NULL;
+ /* Non-default port requested? */
+ portpos = extract_param(&programmer_param, "it87spiport", ",:");
+ if (portpos && strlen(portpos)) {
+ flashport = strtol(portpos, (char **)NULL, 0);
+ msg_pinfo("Forcing serial flash port 0x%04x\n",
+ flashport);
+ sio_write(port, 0x64, (flashport >> 8));
+ sio_write(port, 0x65, (flashport & 0xff));
+ } else if (portpos) {
+ msg_perr("Error: it87spiport specified, but no port "
+ "given.\n");
+ free(portpos);
+ /* FIXME: Return failure here once it87spi_common_init()
+ * can handle the return value sanely.
+ */
+ exit(1);
}
- if (programmer_param) {
- portpos = extract_param(&programmer_param,
- "it87spiport=", ",:");
- if (portpos) {
- flashport = strtol(portpos, (char **)NULL, 0);
- msg_pinfo("Forcing serial flash port 0x%04x\n",
- flashport);
- sio_write(port, 0x64, (flashport >> 8));
- sio_write(port, 0x65, (flashport & 0xff));
- free(portpos);
- }
- }
+ free(portpos);
exit_conf_mode_ite(port);
break;
/* TODO: Handle more IT87xx if they support flash translation */
Index: flashrom-extract_param_everywhere/buspirate_spi.c
===================================================================
--- flashrom-extract_param_everywhere/buspirate_spi.c (Revision 1067)
+++ flashrom-extract_param_everywhere/buspirate_spi.c (Arbeitskopie)
@@ -101,24 +101,18 @@
char *speed = NULL;
int spispeed = 0x7;
- if (programmer_param && !strlen(programmer_param)) {
- free(programmer_param);
- programmer_param = NULL;
- }
- if (programmer_param) {
- dev = extract_param(&programmer_param, "dev=", ",:");
- speed = extract_param(&programmer_param, "spispeed=", ",:");
- if (strlen(programmer_param))
- msg_perr("Unhandled programmer parameters: %s\n",
- programmer_param);
- free(programmer_param);
- programmer_param = NULL;
- }
- if (!dev) {
+ dev = extract_param(&programmer_param, "dev", ",:");
+ if (!dev || !strlen(dev)) {
msg_perr("No serial device given. Use flashrom -p "
"buspirate_spi:dev=/dev/ttyUSB0\n");
return 1;
}
+ ret = buspirate_serialport_setup(dev);
+ if (ret)
+ return ret;
+ free(dev);
+
+ speed = extract_param(&programmer_param, "spispeed", ",:");
if (speed) {
for (i = 0; spispeeds[i].name; i++)
if (!strncasecmp(spispeeds[i].name, speed,
@@ -129,13 +123,11 @@
if (!spispeeds[i].name)
msg_perr("Invalid SPI speed, using default.\n");
}
+ free(speed);
+
/* This works because speeds numbering starts at 0 and is contiguous. */
msg_pdbg("SPI speed is %sHz\n", spispeeds[spispeed].name);
- ret = buspirate_serialport_setup(dev);
- if (ret)
- return ret;
-
/* This is the brute force version, but it should work. */
for (i = 0; i < 19; i++) {
/* Enter raw bitbang mode */
Index: flashrom-extract_param_everywhere/gfxnvidia.c
===================================================================
--- flashrom-extract_param_everywhere/gfxnvidia.c (Revision 1067)
+++ flashrom-extract_param_everywhere/gfxnvidia.c (Arbeitskopie)
@@ -58,11 +58,15 @@
int gfxnvidia_init(void)
{
uint32_t reg32;
+ char *devstring;
get_io_perms();
+ devstring = extract_param(&programmer_param, "pci", ",");
io_base_addr = pcidev_init(PCI_VENDOR_ID_NVIDIA, PCI_BASE_ADDRESS_0,
- gfx_nvidia, programmer_param);
+ gfx_nvidia, devstring);
+ free(devstring);
+
io_base_addr += 0x300000;
msg_pinfo("Detected NVIDIA I/O base address: 0x%x.\n", io_base_addr);
@@ -87,7 +91,6 @@
reg32 |= (1 << 0);
pci_write_long(pcidev_dev, 0x50, reg32);
- free(programmer_param);
pci_cleanup(pacc);
release_io_perms();
return 0;
Index: flashrom-extract_param_everywhere/atahpt.c
===================================================================
--- flashrom-extract_param_everywhere/atahpt.c (Revision 1067)
+++ flashrom-extract_param_everywhere/atahpt.c (Arbeitskopie)
@@ -41,11 +41,14 @@
int atahpt_init(void)
{
uint32_t reg32;
+ char *devstring;
get_io_perms();
+ devstring = extract_param(&programmer_param, "pci", ",");
io_base_addr = pcidev_init(PCI_VENDOR_ID_HPT, PCI_BASE_ADDRESS_4,
- ata_hpt, programmer_param);
+ ata_hpt, devstring);
+ free(devstring);
/* Enable flash access. */
reg32 = pci_read_long(pcidev_dev, REG_FLASH_ACCESS);
@@ -66,7 +69,6 @@
reg32 &= ~(1 << 24);
pci_write_long(pcidev_dev, REG_FLASH_ACCESS, reg32);
- free(programmer_param);
pci_cleanup(pacc);
release_io_perms();
return 0;
Index: flashrom-extract_param_everywhere/serprog.c
===================================================================
--- flashrom-extract_param_everywhere/serprog.c (Revision 1067)
+++ flashrom-extract_param_everywhere/serprog.c (Arbeitskopie)
@@ -298,43 +298,80 @@
int serprog_init(void)
{
uint16_t iface;
- int len;
unsigned char pgmname[17];
unsigned char rbuf[3];
unsigned char c;
- char *num;
- char *dev;
- msg_pspew("%s\n", __func__);
- /* the parameter is either of format "/dev/device:baud" or "ip:port" */
- if ((!programmer_param) || (!strlen(programmer_param))) {
- nodevice:
- msg_perr("Error: No device/host given for the serial programmer driver.\n"
- "Use flashrom -p serprog=/dev/device:baud or flashrom -p serprog=ip:port\n");
- exit(1);
+ char *device;
+ char *baudport;
+ int have_device = 0;
+
+ /* the parameter is either of format "dev=/dev/device:baud" or "ip=ip:port" */
+ device = extract_param(&programmer_param, "dev", ",");
+ if (device && strlen(device)) {
+ baudport = strstr(device, ":");
+ if (baudport) {
+ /* Split device from baudrate. */
+ *baudport = '\0';
+ baudport++;
+ }
+ if (!baudport || !strlen(baudport)) {
+ msg_perr("Error: No baudrate specified.\n"
+ "Use flashrom -p serprog:dev=/dev/device:baud\n");
+ free(device);
+ return 1;
+ }
+ if (strlen(device)) {
+ sp_fd = sp_openserport(device, atoi(baudport));
+ have_device++;
+ }
}
- num = strstr(programmer_param, ":");
- len = num - programmer_param;
- if (!len) goto nodevice;
- if (!num) {
- msg_perr("Error: No port or baudrate specified to serial programmer driver.\n"
- "Use flashrom -p serprog=/dev/device:baud or flashrom -p serprog=ip:port\n");
- exit(1);
+ if (device && !strlen(device)) {
+ msg_perr("Error: No device specified.\n"
+ "Use flashrom -p serprog:dev=/dev/device:baud\n");
+ free(device);
+ return 1;
}
- len = num - programmer_param;
- dev = malloc(len + 1);
- if (!dev) sp_die("Error: memory allocation failure");
- memcpy(dev, programmer_param, len);
- dev[len] = 0;
- num = strdup(num + 1);
- if (!num) sp_die("Error: memory allocation failure");
- free(programmer_param);
- programmer_param = NULL;
+ free(device);
- if (dev[0] == '/') sp_fd = sp_openserport(dev, atoi(num));
- else sp_fd = sp_opensocket(dev, atoi(num));
+ device = extract_param(&programmer_param, "ip", ",");
+ if (have_device && device) {
+ msg_perr("Error: Both host and device specified.\n"
+ "Please use either dev= or ip= but not both.\n");
+ free(device);
+ return 1;
+ }
+ if (device && strlen(device)) {
+ baudport = strstr(device, ":");
+ if (baudport) {
+ /* Split host from port. */
+ *baudport = '\0';
+ baudport++;
+ }
+ if (!baudport || !strlen(baudport)) {
+ msg_perr("Error: No port specified.\n"
+ "Use flashrom -p serprog:ip=ipaddr:port\n");
+ free(device);
+ return 1;
+ }
+ if (strlen(device)) {
+ sp_fd = sp_opensocket(device, atoi(baudport));
+ have_device++;
+ }
+ }
+ if (device && !strlen(device)) {
+ msg_perr("Error: No host specified.\n"
+ "Use flashrom -p serprog:ip=ipaddr:port\n");
+ free(device);
+ return 1;
+ }
+ free(device);
- free(dev); dev = NULL;
- free(num); num = NULL;
+ if (!have_device) {
+ msg_perr("Error: Neither host nor device specified.\n"
+ "Use flashrom -p serprog:dev=/dev/device:baud or "
+ "flashrom -p serprog:ip=ipaddr:port\n");
+ return 1;
+ }
msg_pdbg(MSGHEADER "connected - attempting to synchronize\n");
Index: flashrom-extract_param_everywhere/nicrealtek.c
===================================================================
--- flashrom-extract_param_everywhere/nicrealtek.c (Revision 1067)
+++ flashrom-extract_param_everywhere/nicrealtek.c (Arbeitskopie)
@@ -41,10 +41,14 @@
int nicrealtek_init(void)
{
+ char *devstring;
+
get_io_perms();
+ devstring = extract_param(&programmer_param, "pci", ",");
io_base_addr = pcidev_init(PCI_VENDOR_ID_REALTEK, PCI_BASE_ADDRESS_0,
- nics_realtek, programmer_param);
+ nics_realtek, devstring);
+ free(devstring);
buses_supported = CHIP_BUSTYPE_PARALLEL;
@@ -53,10 +57,14 @@
int nicsmc1211_init(void)
{
+ char *devstring;
+
get_io_perms();
+ devstring = extract_param(&programmer_param, "pci", ",");
io_base_addr = pcidev_init(PCI_VENDOR_ID_SMC1211, PCI_BASE_ADDRESS_0,
- nics_realteksmc1211, programmer_param);
+ nics_realteksmc1211, devstring);
+ free(devstring);
buses_supported = CHIP_BUSTYPE_PARALLEL;
@@ -66,7 +74,6 @@
int nicrealtek_shutdown(void)
{
/* FIXME: We forgot to disable software access again. */
- free(programmer_param);
pci_cleanup(pacc);
release_io_perms();
return 0;
Index: flashrom-extract_param_everywhere/nic3com.c
===================================================================
--- flashrom-extract_param_everywhere/nic3com.c (Revision 1067)
+++ flashrom-extract_param_everywhere/nic3com.c (Arbeitskopie)
@@ -56,10 +56,15 @@
int nic3com_init(void)
{
+ char *devstring;
+
get_io_perms();
+ devstring = extract_param(&programmer_param, "pci", ",");
io_base_addr = pcidev_init(PCI_VENDOR_ID_3COM, PCI_BASE_ADDRESS_0,
- nics_3com, programmer_param);
+ nics_3com, devstring);
+ free(devstring);
+
id = pcidev_dev->device_id;
/* 3COM 3C90xB cards need a special fixup. */
@@ -96,7 +101,6 @@
OUTL(internal_conf, io_base_addr + INTERNAL_CONFIG);
}
- free(programmer_param);
pci_cleanup(pacc);
release_io_perms();
return 0;
Index: flashrom-extract_param_everywhere/ft2232_spi.c
===================================================================
--- flashrom-extract_param_everywhere/ft2232_spi.c (Revision 1067)
+++ flashrom-extract_param_everywhere/ft2232_spi.c (Arbeitskopie)
@@ -76,46 +76,49 @@
int f;
struct ftdi_context *ftdic = &ftdic_context;
unsigned char buf[512];
- char *portpos = NULL;
int ft2232_type = FTDI_FT4232H;
enum ftdi_interface ft2232_interface = INTERFACE_B;
+ char *arg;
- if (ftdi_init(ftdic) < 0) {
- msg_perr("ftdi_init failed\n");
- return EXIT_FAILURE; // TODO
- }
-
- if (programmer_param && !strlen(programmer_param)) {
- free(programmer_param);
- programmer_param = NULL;
- }
- if (programmer_param) {
- if (strstr(programmer_param, "2232"))
+ arg = extract_param(&programmer_param, "type", ",:");
+ if (arg) {
+ if (!strcmp(arg, "2232H"))
ft2232_type = FTDI_FT2232H;
- if (strstr(programmer_param, "4232"))
+ else if (!strcmp(arg, "4232H"))
ft2232_type = FTDI_FT4232H;
- portpos = strstr(programmer_param, "port=");
- if (portpos) {
- portpos += 5;
- switch (toupper(*portpos)) {
- case 'A':
- ft2232_interface = INTERFACE_A;
- break;
- case 'B':
- ft2232_interface = INTERFACE_B;
- break;
- default:
- msg_perr("Invalid interface specified, "
- "using default.\n");
- }
+ else {
+ msg_perr("Error: Invalid device type specified.\n");
+ free(arg);
+ return 1;
}
- free(programmer_param);
}
+ free(arg);
+ arg = extract_param(&programmer_param, "port", ",:");
+ if (arg) {
+ switch (toupper(*arg)) {
+ case 'A':
+ ft2232_interface = INTERFACE_A;
+ break;
+ case 'B':
+ ft2232_interface = INTERFACE_B;
+ break;
+ default:
+ msg_perr("Error: Invalid port/interface specified.\n");
+ free(arg);
+ return 1;
+ }
+ }
+ free(arg);
msg_pdbg("Using device type %s ",
(ft2232_type == FTDI_FT2232H) ? "2232H" : "4232H");
msg_pdbg("interface %s\n",
(ft2232_interface == INTERFACE_A) ? "A" : "B");
+ if (ftdi_init(ftdic) < 0) {
+ msg_perr("ftdi_init failed\n");
+ return EXIT_FAILURE; // TODO
+ }
+
f = ftdi_usb_open(ftdic, 0x0403, ft2232_type);
if (f < 0 && f != -5) {
Index: flashrom-extract_param_everywhere/satasii.c
===================================================================
--- flashrom-extract_param_everywhere/satasii.c (Revision 1067)
+++ flashrom-extract_param_everywhere/satasii.c (Arbeitskopie)
@@ -43,11 +43,15 @@
{
uint32_t addr;
uint16_t reg_offset;
+ char *devstring;
get_io_perms();
+ devstring = extract_param(&programmer_param, "pci", ",");
pcidev_init(PCI_VENDOR_ID_SII, PCI_BASE_ADDRESS_0, satas_sii,
- programmer_param);
+ devstring);
+ free(devstring);
+
id = pcidev_dev->device_id;
if ((id == 0x3132) || (id == 0x3124)) {
@@ -71,7 +75,6 @@
int satasii_shutdown(void)
{
- free(programmer_param);
pci_cleanup(pacc);
release_io_perms();
return 0;
Index: flashrom-extract_param_everywhere/dummyflasher.c
===================================================================
--- flashrom-extract_param_everywhere/dummyflasher.c (Revision 1067)
+++ flashrom-extract_param_everywhere/dummyflasher.c (Arbeitskopie)
@@ -25,44 +25,46 @@
#include "flash.h"
#include "chipdrivers.h"
+static void tolower_string(char *str)
+{
+ for (; *str != '\0'; str++)
+ *str = (char)tolower((unsigned char)*str);
+}
+
int dummy_init(void)
{
- int i;
+ char *bustext = NULL;
+
msg_pspew("%s\n", __func__);
- /* "all" is equivalent to specifying no type. */
- if (programmer_param && (!strcmp(programmer_param, "all"))) {
- free(programmer_param);
- programmer_param = NULL;
- }
- if (!programmer_param)
- programmer_param = strdup("parallel,lpc,fwh,spi");
+ bustext = extract_param(&programmer_param, "bus", ",:");
+ msg_pdbg("Requested buses are: %s\n", bustext ? bustext : "default");
+ if (!bustext)
+ bustext = strdup("parallel+lpc+fwh+spi");
/* Convert the parameters to lowercase. */
- for (i = 0; programmer_param[i] != '\0'; i++)
- programmer_param[i] =
- (char)tolower((unsigned char)programmer_param[i]);
+ tolower_string(bustext);
buses_supported = CHIP_BUSTYPE_NONE;
- if (strstr(programmer_param, "parallel")) {
+ if (strstr(bustext, "parallel")) {
buses_supported |= CHIP_BUSTYPE_PARALLEL;
msg_pdbg("Enabling support for %s flash.\n", "parallel");
}
- if (strstr(programmer_param, "lpc")) {
+ if (strstr(bustext, "lpc")) {
buses_supported |= CHIP_BUSTYPE_LPC;
msg_pdbg("Enabling support for %s flash.\n", "LPC");
}
- if (strstr(programmer_param, "fwh")) {
+ if (strstr(bustext, "fwh")) {
buses_supported |= CHIP_BUSTYPE_FWH;
msg_pdbg("Enabling support for %s flash.\n", "FWH");
}
- if (strstr(programmer_param, "spi")) {
+ if (strstr(bustext, "spi")) {
buses_supported |= CHIP_BUSTYPE_SPI;
spi_controller = SPI_CONTROLLER_DUMMY;
msg_pdbg("Enabling support for %s flash.\n", "SPI");
}
if (buses_supported == CHIP_BUSTYPE_NONE)
msg_pdbg("Support for all flash bus types disabled.\n");
- free(programmer_param);
+ free(bustext);
return 0;
}
Index: flashrom-extract_param_everywhere/chipset_enable.c
===================================================================
--- flashrom-extract_param_everywhere/chipset_enable.c (Revision 1067)
+++ flashrom-extract_param_everywhere/chipset_enable.c (Arbeitskopie)
@@ -300,11 +300,8 @@
int max_decode_fwh_decode = 0;
int contiguous = 1;
- if (programmer_param)
- idsel = strstr(programmer_param, "fwh_idsel=");
-
- if (idsel) {
- idsel += strlen("fwh_idsel=");
+ idsel = extract_param(&programmer_param, "fwh_idsel", ",:");
+ if (idsel && strlen(idsel)) {
fwh_conf = (uint32_t)strtoul(idsel, NULL, 0);
/* FIXME: Need to undo this on shutdown. */
@@ -312,7 +309,15 @@
pci_write_long(dev, 0xd0, fwh_conf);
pci_write_word(dev, 0xd4, fwh_conf);
/* FIXME: Decode settings are not changed. */
+ } else if (idsel) {
+ msg_perr("Error: idsel= specified, but no number given.\n");
+ free(idsel);
+ /* FIXME: Return failure here once internal_init() starts
+ * to care about the return value of the chipset enable.
+ */
+ exit(1);
}
+ free(idsel);
/* Ignore all legacy ranges below 1 MB.
* We currently only support flashing the chip which responds to
Index: flashrom-extract_param_everywhere/flashrom.c
===================================================================
--- flashrom-extract_param_everywhere/flashrom.c (Revision 1067)
+++ flashrom-extract_param_everywhere/flashrom.c (Arbeitskopie)
@@ -428,7 +428,15 @@
int programmer_init(void)
{
- return programmer_table[programmer].init();
+ int ret;
+
+ ret = programmer_table[programmer].init();
+ if (programmer_param && strlen(programmer_param)) {
+ msg_perr("Unhandled programmer parameters: %s\n",
+ programmer_param);
+ ret = 1;
+ }
+ return ret;
}
int programmer_shutdown(void)
@@ -536,22 +544,24 @@
char *strcat_realloc(char *dest, const char *src)
{
dest = realloc(dest, strlen(dest) + strlen(src) + 1);
- if (!dest)
+ if (!dest) {
+ msg_gerr("Out of memory!\n");
return NULL;
+ }
strcat(dest, src);
return dest;
}
/* This is a somewhat hacked function similar in some ways to strtok().
- * It will look for needle in haystack, return a copy of needle and remove
- * everything from the first occurrence of needle to the next delimiter
- * from haystack.
+ * It will look for needle with a subsequent '=' in haystack, return a copy of
+ * needle and remove everything from the first occurrence of needle to the next
+ * delimiter from haystack.
*/
char *extract_param(char **haystack, char *needle, char *delim)
{
- char *param_pos, *rest, *tmp;
- char *dev = NULL;
- int devlen;
+ char *param_pos, *opt_pos, *rest;
+ char *opt = NULL;
+ int optlen;
int needlelen;
needlelen = strlen(needle);
@@ -567,43 +577,41 @@
do {
if (!param_pos)
return NULL;
- /* Beginning of the string? */
- if (param_pos == *haystack)
- break;
- /* After a delimiter? */
- if (strchr(delim, *(param_pos - 1)))
- break;
+ /* Needle followed by '='? */
+ if (param_pos[needlelen] == '=') {
+
+ /* Beginning of the string? */
+ if (param_pos == *haystack)
+ break;
+ /* After a delimiter? */
+ if (strchr(delim, *(param_pos - 1)))
+ break;
+ }
/* Continue searching. */
param_pos++;
param_pos = strstr(param_pos, needle);
} while (1);
-
+
if (param_pos) {
- param_pos += strlen(needle);
- devlen = strcspn(param_pos, delim);
- if (devlen) {
- dev = malloc(devlen + 1);
- if (!dev) {
- msg_gerr("Out of memory!\n");
- exit(1);
- }
- strncpy(dev, param_pos, devlen);
- dev[devlen] = '\0';
+ /* Get the string after needle and '='. */
+ opt_pos = param_pos + needlelen + 1;
+ optlen = strcspn(opt_pos, delim);
+ /* Return an empty string if the parameter was empty. */
+ opt = malloc(optlen + 1);
+ if (!opt) {
+ msg_gerr("Out of memory!\n");
+ exit(1);
}
- rest = param_pos + devlen;
+ strncpy(opt, opt_pos, optlen);
+ opt[optlen] = '\0';
+ rest = opt_pos + optlen;
+ /* Skip all delimiters after the current parameter. */
rest += strspn(rest, delim);
- param_pos -= strlen(needle);
memmove(param_pos, rest, strlen(rest) + 1);
- tmp = realloc(*haystack, strlen(*haystack) + 1);
- if (!tmp) {
- msg_gerr("Out of memory!\n");
- exit(1);
- }
- *haystack = tmp;
+ /* We could shrink haystack, but the effort is not worth it. */
}
-
- return dev;
+ return opt;
}
/* start is an offset to the base address of the flash chip */
Index: flashrom-extract_param_everywhere/internal.c
===================================================================
--- flashrom-extract_param_everywhere/internal.c (Revision 1067)
+++ flashrom-extract_param_everywhere/internal.c (Arbeitskopie)
@@ -121,36 +121,45 @@
int force_laptop = 0;
char *arg;
- arg = extract_param(&programmer_param, "boardenable=", ",:");
+ arg = extract_param(&programmer_param, "boardenable", ",:");
if (arg && !strcmp(arg,"force")) {
force_boardenable = 1;
} else if (arg && !strlen(arg)) {
msg_perr("Missing argument for boardenable.\n");
+ free(arg);
+ return 1;
} else if (arg) {
msg_perr("Unknown argument for boardenable: %s\n", arg);
- exit(1);
+ free(arg);
+ return 1;
}
free(arg);
- arg = extract_param(&programmer_param, "boardmismatch=", ",:");
+ arg = extract_param(&programmer_param, "boardmismatch", ",:");
if (arg && !strcmp(arg,"force")) {
force_boardmismatch = 1;
} else if (arg && !strlen(arg)) {
msg_perr("Missing argument for boardmismatch.\n");
+ free(arg);
+ return 1;
} else if (arg) {
msg_perr("Unknown argument for boardmismatch: %s\n", arg);
- exit(1);
+ free(arg);
+ return 1;
}
free(arg);
- arg = extract_param(&programmer_param, "laptop=", ",:");
+ arg = extract_param(&programmer_param, "laptop", ",:");
if (arg && !strcmp(arg,"force_I_want_a_brick")) {
force_laptop = 1;
} else if (arg && !strlen(arg)) {
msg_perr("Missing argument for laptop.\n");
+ free(arg);
+ return 1;
} else if (arg) {
msg_perr("Unknown argument for laptop: %s\n", arg);
- exit(1);
+ free(arg);
+ return 1;
}
free(arg);
Index: flashrom-extract_param_everywhere/nicnatsemi.c
===================================================================
--- flashrom-extract_param_everywhere/nicnatsemi.c (Revision 1067)
+++ flashrom-extract_param_everywhere/nicnatsemi.c (Arbeitskopie)
@@ -36,10 +36,14 @@
int nicnatsemi_init(void)
{
+ char *devstring;
+
get_io_perms();
+ devstring = extract_param(&programmer_param, "pci", ",");
io_base_addr = pcidev_init(PCI_VENDOR_ID_NATSEMI, PCI_BASE_ADDRESS_0,
- nics_natsemi, programmer_param);
+ nics_natsemi, devstring);
+ free(devstring);
buses_supported = CHIP_BUSTYPE_PARALLEL;
@@ -48,7 +52,6 @@
int nicnatsemi_shutdown(void)
{
- free(programmer_param);
pci_cleanup(pacc);
release_io_perms();
return 0;
--
http://www.hailfinger.org/
More information about the flashrom
mailing list